Related
Hi All, I am after advice on how to get my original ROM back.
I upgraded to MksBiGStorage, and following the instructions I backed up my original ROM first.
My original ROM is on my Hard Drive but I think because I used a 1Gb SD card to back it up with ntrw.exe, it is 1Gb in size.
I was hoping I could just use ntrw.exe and transfer my 1Gb backup ROM back to my SD card again using ntrw.exe and then hard reset my phone and it would see the ROM and install it - BUGGER, that doesnt seem to work.
Can anyone tell me how to get my backed up ROM back onto my phone? Or does anyone have the Original Orange UK SPV m500 ROM I could download and install?
Desperately want my original phone back - Please help guys, you are my only hope. (I Sound like Princess Leah asking Obi-Wan).
guess i'm Yoda then
Think you put the rom after your sd's mbr with ntrw. To solve this do the following steps:
- create a romdump of your current rom, you know how don't you?
- now copy your backup rom on the sd without formatting it.
romupdate has overwritten the sd's mbr and ntrw will happily write the backup.nb1 image at the start position of your sd.
Now your magician should be able to se the image.
Also you cashrink your backup image extremely. Open the mksbigstorager romimage in hexedit go to the last byte and get the address and bytes. Now open your backup, go to the same address and look for the same bitpattern as it is very recognizable this shouldn't give a problem.
Now delete all the bytes behind them & you're left with a handy 64Mb image
Good luck, M
I dont mean to sound ungreatful for your reply, but I have no idea what you mean.
I only have one backup of my old ROM, and that is the 1Gb file on my hard drive.
Can you give me a step by step procedure for restoring it?
If I understand correctly, you are saying to backup my (not wanted) mksbigstorage ROM again to SD (which will write the MBR to the SD.
Then, copy my original ROM back to the SD using ntrw, then try and insert my SD back into my device and it will work?
Is that right?
MaJiK said:
If I understand correctly, you are saying to backup my (not wanted) mksbigstorage ROM again to SD (which will write the MBR to the SD.
Then, copy my original ROM back to the SD using ntrw, then try and insert my SD back into my device and it will work?
Is that right?
Click to expand...
Click to collapse
Yes that's right the rom-dump will overwrite/destroy the mbr. After that write the old 1Gb file on the same sd without formatting it, then it will work.
I'll post the steps to cut the 1Gb to 64Mb later as I need access to my PC for details on it. I did it myself as BS 1.13 on the ftp is my image and around 64Mb in size & mksbigstorager can do it too only that will do it with the BS patch & manually you get it without.
first thing is to get your old-rom on your device so start dumping ;-)
Regards, M
oltp, thanks for your help man. I am currently transferring my ROM to the SD.
Where abouts in NL are you from? I love NL - You guys rock
If ever I get the chance I will retire/emigrate in the Netherlands. Love it.
Just inserted card, and it says its trying to update the ROM.
MANY, MANY THANKS for taking the time to answer my questions.
I really appreciate it.... YODA!
You're welcome I'm just the messenger in this, someone else 'discovered' the mbr problem & posted it here.
Glad it works for you too.
Regarding the of the world I'm from the home of cannabis (Amsterdam) & live now near the city from 'a bridge to far' (Arnhem). Love it here too near the forests etc. Somehow the Dutch get a lot of bad credits lately in the news so it's nice to read that there are people liking Holland. So thank you & I guess you're device is ready for use by now.
Cheers, M
Absolutely spot on.
Once again, thanks for your help - I had almost given up.
I hope this helps others out aswell who need to revert back to the original ROM.
Regarding the 1Gb file, there are a couple of people in another thread of mine who obviously didnt back their ROM up and are asking for the original Orange UK ROM for download.
Is it safe to upload the ROM I have for them? I dont understand why its not downloadable anywhere on the net at the moment?
I will happily upload this ROM for others if its not going to cause licensing issues or invalidate my ROM at all.
I took a look at using the HexEdit program and think I know what I need to do, but selecting all the bytes after the address seems to take AGES! FOREVER.
Thanks again for your time oltp, I am well chuffed
Excuse me for my bad English, you better select to first 64Mb & save that part in a new file don't forget to include those footer bytes.
When you don't want people to get your device id, just replace those first 416bytes with a looping 'please put your own 416bytes here' or something simular. Must work don't you think?
I just uploaded mine as I hope, guess, belief they're not able or willing to backtrack me in the coming 18 months. Then my contract ends & I probably get a new 'phone'.
So pls upload your shrunken & zipped image you can pls a lot of others with it.
Cheers, M
Hi I know the big storage hack is plastered all over this forum but i still cant get it right.Some one please help me!
Ive got a magician with rom version 1.13.00 WWE radio v. 1.12.00 (i used to have 1.12.00 but i upgraded it by accident.<I woz finkin of it anyway>)
I fink Ive tried every procedure possible but always have problems but basically this is what ive done:
1.Using OS image tool ive copied my rom to pc.
2.Ive changed the 80 00 00 thingy to b8 01.
3.Ive tried to use the os image tool to write it back t ppc but it comes with a usb/communication error in programme A.Im using this way because I have only 32mb mmc card.
Any help would be much appreciated,
Thanks
wiki
Try the wiki (top right link on the page) & go to the magician section. It contains a description howto patch a shipped-rom, the one you used to upgrade to 1.13WWE, & get BS. Apperently you missed this method.
Cheers, M
I already have all of them files.Wen I patch it the size goes right up then 'programme a' doesnt copy it over becuase its too big.it has 2 b excactly 32 i fink and after i patch it the size changes.
My main problem is getting the rom over 2 the magician.Since I dont have a card the only 2 ways i can fink are using osimage tool or program a, both of these im having problems with.I have roms that i have patched and changed the 416 bytes to my roms.I have roms that were patched and ive changed to my roms.I have roms made using byte copy.I just cant get any of them over!!
Thanks 4 ure help,
Gareth
I already have all of them files.Wen I patch it the size goes right up then 'programme a' doesnt copy it over becuase its too big.it has 2 b excactly 32 i fink and after i patch it the size changes.
My main problem is getting the rom over 2 the magician.Since I dont have a card the only 2 ways i can fink are using osimage tool or program a, both of these im having problems with.I have roms that i have patched and changed the 416 bytes to my roms.I have roms that were patched and ive changed to my roms.I have roms made using byte copy.I just cant get any of them over!!
Thanks 4 ure help,
Gareth
Stop,
You're going in the wrong direction. The BS from shipped-rom method is about patching the provider supplied exe file. & after the patch you run it like a regular rom-upgrade. No SD or MMC involved!!! It's a rom-update via USB like the normal update.
pls read it once again @ the wiki.
ok thanks im trying that now.Im stuck on getting nbfdec to run.Ive extracted it to the unzipped rom folder.I open ms-dos command prompt and drag and drop the .exe on the command line to save typing the path.The program runs but then it crashes.Can anyone help me?
Try putting everything in "C:\BS" saves a lot of typing errors including filename handling.
Ive done that now but I dont know how to execute the command.Do you think you could type the whole command for me?When I open command prompt it says this c:\documents and settings\rod simpson\> ive tryped typing in that command but i dont know how to put it in with the path etc.
Sorry for going on and on I cant get my head round it!
Thanks
garethsimpsonuk said:
Ive done that now but I dont know how to execute the command.Do you think you could type the whole command for me?When I open command prompt it says this c:\documents and settings\rod simpson\> ive tryped typing in that command but i dont know how to put it in with the path etc.
Sorry for going on and on I cant get my head round it!
Thanks
Click to expand...
Click to collapse
Hi Rod,
To go to C:\BS from your personal doc&settings type on the commandline:
cd \ [Enter]
now you should be in C:\
then type:
cd bs [Enter]
now you should be in C:\BS
Works for other directories too.
Cheers, M
Thanks, that helped me a lot.Ive done everything els now so I converted it back to nbf and then executed the maupgrade_noid.It checked device info then displayed the rom to and from screen and both were blank.I proceeded and it displayed the 'success' screen but nothing had actually happened on the ppc.Ive tried the other upgrade program and the one thats cracked on the site.
Any help would be much appreciated
Thanks
Did you reset after the update process finished? & if so did it boot normally? & if so did you look at the internal storage folder size? Cause that's the only thing that's changed & the ext-rom has disappeared. Oh & you shouldn't see the customization start after a hard-reset...
btw rom to & from shouldn't be blank, pls run the update program without patch cause I think the editing somehow invalidated the shipped-rom. The original upgrade program should work & if so you know what's going on. If the original program fails there might be something with your device.
So start the plain shipped-rom first to find out..
Thankyou!Its worked!!
I went from scratch and downloaded all the files again.This time i didnt put my own header in the file because i thought thats where i'm going wrong.My devicedata.txt file looked like gibberish to me and it wouldnt copy and paste in to hex editor.So i just left it.I changed the 2 values in the code, converted it and flashed it.Will not having my header cause problems?My storage is now 26.72mb is that right?
Thankyou very much oltp for your help.It's much appreciated.
I think this site is long overdue a donation from me.
Cheers m8
Thankyou!Its worked!!
I went from scratch and downloaded all the files again.This time i didnt put my own header in the file because i thought thats where i'm going wrong.My devicedata.txt file looked like gibberish to me and it wouldnt copy and paste in to hex editor.So i just left it.I changed the 2 values in the code, converted it and flashed it.Will not having my header cause problems?My storage is now 26.72mb is that right?
Thankyou very much oltp for your help.It's much appreciated.
I think this site is long overdue a donation from me.
Cheers m8
The header contains info about romtype & provider name, probably some things more I'm
not sure about. The reason for changing it is to avoid errors like the country id error. With the use of maupgradeut_noid it's less important.
One thing I'm questioning is the reason why some of us have probs with connecting to the, I believe, special O2 services. Some claim there not able to connect anymore... Can some other setting as well. I'm on T-Mobile & everything works fine.
Basically if the upgrade was succesfull, you have an enlarged storage & the rest of your device will be working as before.
Cheers, M
how much space would i have in my main memory now? i have a 64+64 system (O2 Xda Mini) now branded to T-Mobile 1.33 and now applied the new patch (BIG STORAGE) using the Wiki Information guides. However any idea how much FREE space on first reboot i should have.
did the first reboot...(soft reboot) after flash...its been 3 mins and just the T-Mobile Screen..how lng should i wait before i "think" its a bad flash?
nevermind got it
Total Main Memory - (FREE MEMORY) - 43.99MB Storage / 25.54 MB Programs! woo hoo this is HOT
shivam said:
did the first reboot...(soft reboot) after flash...its been 3 mins and just the T-Mobile Screen..how lng should i wait before i "think" its a bad flash?
Click to expand...
Click to collapse
First boot takes much more time than next boots.
Have fun, M
all,
look over here.
cheers!
Sorry to say, but it's old news. We got a thread about it for three months now I guess with that method. Problem is you always need to update first & then dump your rom again. & somehow not all dumps are accurate. The brick change with a SD is larger than with a shipped-rom.
M
Guy's,
Finally you can flash any rom to your device without help from the 2nd device. I believe it's a great news for them who is suffering from the broken USB connecor.
It's tested on my G3 device with my latest ROM's and other should work without problem.
Procedure:
1. Download the tool and unrar somewhere in your pc.
2. Decode the rom image (nk.nbf) using HTC64 tool and put it (nk.nba) under the "SD_Flash" directory.
3. Run the "SDFlash_G3.cmd" and follow instruction on the screen.
Please note, it's limited to G3 device only and I may add support for G4 device in future.
SD-ROM image tool:
http://vidmes.com/Uni/ROMs/Tomal/Tools/Ranju_SD_Flash.rar
!! IMPORTANT: Do it at your own risk. I'll not take any responsibility if you damage your device. !!
Cheers
Great stuff.
I especially look forward to a G4 release.
My USB commector broke off the circuit board recently and was floating about inside the device for a while before I opened up the device and glued it back in position onto the circuitboard. It now works (the 5 little pins are connected) so I can charge the battery through it, but I don't really trust it to flash a firmware through.
Thankfully I'm already on the ROM I usually go back to (latest T-Mobile WM5) after playing around with WM6 and WM6.1.
Nice to see developments being made for those of us with handicapped uni's!!!
Thanks a ton, Ranju !
Have already downloaded and unpacked it. I'll certainly give it a try as soon as you release your v7.7 ROM.
Cheers!
Carlos
Dear Ranju,
You keep on surprising us!
Thanks friend,
Mohamed
Ranju, as usual, you are the man!
I experienced the "direct flash" on a Mio A701 and it's really a great feature. Now I can't ask you anything more... ehm...
..
... I was kidding I'd like only the new build of your rom eheh
thanks!!!
Thank you ranju for this great tool, so I can flash WM6.1 on my MDA Pro with broken miniUSB!
casouzaj said:
Thanks a ton, Ranju !
Have already downloaded and unpacked it. I'll certainly give it a try as soon as you release your v7.7 ROM.
Cheers!
Carlos
Click to expand...
Click to collapse
ha ha ha, nice catch!
Also waiting for a new release... and G4 tool
Cheers
Lord of the binary digits
Hi Ranju!
Thank you very much for sharing your great work.
Cheers
I tried to flash using bluetooth (yeah, I was stupid) and since then it's hanging in bootloader mode.
The mini-USB connector broke before (that's why I was using BT) and now I finally thought I had a solution to get it working again.
However, when I follow your steps and reset (backlight + power + reset) it doesn't even seem to look at the SD-card; it just shows serial + v1.00 again.
Any ideas?
In SDimage it get's to only 3,21%, but's that's normal on a 2 gig card I presume?
martinbl said:
@ 13,05% I get an error in SD Imaging tool and it stops there...
Any idea why?
Click to expand...
Click to collapse
what is the size of sd, 512mb?
ranju said:
what is the size of sd, 152mb?
Click to expand...
Click to collapse
I just edited my post .
I used another card and that got only to 3,21% or something (2gig card) so I presumed that's normal because of the image size?
To be complete:
I tried to flash using bluetooth (yeah, I was stupid) and since then it's hanging in bootloader mode.
The mini-USB connector broke before (that's why I was using BT) and now I finally thought I had a solution to get it working again.
However, when I follow your steps and reset (backlight + power + reset) it doesn't even seem to look at the SD-card; it just shows serial + v1.00 again.
martinbl said:
I just edited my post .
I used another card and that got only to 3,21% or something (2gig card) so I presumed that's normal because of the image size?
To be complete:
I tried to flash using bluetooth (yeah, I was stupid) and since then it's hanging in bootloader mode.
The mini-USB connector broke before (that's why I was using BT) and now I finally thought I had a solution to get it working again.
However, when I follow your steps and reset (backlight + power + reset) it doesn't even seem to look at the SD-card; it just shows serial + v1.00 again.
Click to expand...
Click to collapse
Yes, it's normal.
Did you inserted the card to device before entering to bootloader?
Read and follow all the instructions carefully in the .cmd file.
For more info, read Htc Service manual of Universal.
Thanks Ranju!!!
I am waiting for G4 device
ranju said:
Yes, it's normal.
Did you inserted the card to device before entering to bootloader?
Read and follow all the instructions carefully in the .cmd file.
For more info, read Htc Service manual of Universal.
Click to expand...
Click to collapse
I shall tell about all the steps I took:
1. Download the tool and unrar somewhere in your pc.
- Easy.
2. Decode the rom image (nk.nbf) using HTC64 tool and put it (nk.nba) under the "SD_Flash" directory.
- I took your(?) "Ranju_v76_WM61_19209_19209_1_0_2", unrarred it and decoded it to nk.nba.
3. Run the "SDFlash_G3.cmd" and follow instruction on the screen.
g3.bin and nk_sd_g3.bin are created.
After that, I put in my Dane-Elec 2 gig SD-card and format it to FAT32.
SDimage is opened and I select the FAT32 F: drive.
After that I push the "Import SD Image" button.
Fill in "i agree", click "ok" and "yes" (with "hex" unchecked).
There I choose bin files and select "nk_sd_g3."
I then click "Ignore", "yes" and "ignore" and it's starts writing.
At 3,21% I get the dump incomplete notification and click ok.
I then put the card in my Universal, press the light and power button and the reset pin.
For a second or so the v1.00 disapears and it comes back without doing/checking/reading anything.
I'm quit sure the SD-card should work because before I flashed using BT, it worked and I tested the same procedure with another card.
Any ideas what I'm doing wrong or why the Universal doesn't even seem to look for the SD-card?
martinbl said:
I shall tell about all the steps I took:
1. Download the tool and unrar somewhere in your pc.
- Easy.
2. Decode the rom image (nk.nbf) using HTC64 tool and put it (nk.nba) under the "SD_Flash" directory.
- I took your(?) "Ranju_v76_WM61_19209_19209_1_0_2", unrarred it and decoded it to nk.nba.
3. Run the "SDFlash_G3.cmd" and follow instruction on the screen.
g3.bin and nk_sd_g3.bin are created.
After that, I put in my Dane-Elec 2 gig SD-card and format it to FAT32.
SDimage is opened and I select the FAT32 F: drive.
After that I push the "Import SD Image" button.
Fill in "i agree", click "ok" and "yes" (with "hex" unchecked).
There I choose bin files and select "nk_sd_g3."
I then click "Ignore", "yes" and "ignore" and it's starts writing.
At 3,21% I get the dump incomplete notification and click ok.
I then put the card in my Universal, press the light and power button and the reset pin.
For a second or so the v1.00 disapears and it comes back without doing/checking/reading anything.
I'm quit sure the SD-card should work because before I flashed using BT, it worked and I tested the same procedure with another card.
Any ideas what I'm doing wrong or why the Universal doesn't even seem to look for the SD-card?
Click to expand...
Click to collapse
The same problem, I folowed all of the instructions as it is, but only serial 1.01 on the screen and no look for the image, i have tried with 2 SD cards, one 256 MB and the other is 512 MB, but there was no difference....
PLZ help
hbahaie said:
The same problem, I folowed all of the instructions as it is, but only serial 1.01 on the screen and no look for the image, i have tried with 2 SD cards, one 256 MB and the other is 512 MB, but there was no difference....
PLZ help
Click to expand...
Click to collapse
Yup, same problem here! I tried with a 512MB Toshiba SD card, previously formatted both to FAT(16) and FAT32. SDImage.exe runs up to 12.91% (FAT) or 12.93% (FAT32), with such card capacity. Same results: my Exec just sits there in booloader mode forever...
Cheers!
Carlos
all the steps are correct .
I'm sure root cause is under the header (g3.bin). it's a mmc header and I suppose there is a difference between sd & mmc header. I'll verify once I can arrange a sd card. alternatively someone can try it using a mmc card so that I can reach to a conclusion.
Hi ranju,
Uploading my MMC header for comparison purposes.
I'm also looking for SD header, g3/g4 both the devices for analysis.
So does this work with a G4? or has it not been tested?
Hi,
I'm sorry about this post but there seems to be an anormous amount of information which doesn't make a lot of sense to me.
All I want to do is upgrade my palm treo 750 from win5.0 to 6.1.
I've downloaded the rom but it doesn't upgarade. So I need to figure out a way to flash this phone so it can be upgraded to any roms.
I have tried the Cheetahunlocker which doens't work. It gets stuck on 0% then times out.
Could someone please give me some basic instructions on the best way to do this on the treo.
I've done this on the TYTN2 whith no issues however on this phone, it seems to be a lot harder.
Thanks in advance.
Your device needs to be unlocked. You can do this by calling ATT and getting unlock code or by using Magic_Unlocker.
search
Also you will need to have the HardSPL installed which is Step 1 only of the CheetahUnlocker
I just did it yesterday so I know it works.
After you get the phone unlocked, name the ROM .nbh file CHEEIMG.nbh and then put it on the SD card
The start the CheetahUnlocker process as it enters the HardSPL process it will go ahead and run the CHEEIMG file and flash your ROM
(it works ! ) DON"T CHANGE THE RADIO !!!!
After doing that be sure and reclaim your ROM space - search web for Removing Ext ROM and do that process, hard reset and you are ready to go
Takes about 15 min!
jcrompton said:
After you get the phone unlocked, name the ROM .nbh file CHEEIMG.nbh and then put it on the SD card
Click to expand...
Click to collapse
Thanks for your info.
sigh..
The rom is an exe file...
I downloaded 7-zip, extracted the rom to a folder.
Looking through it, I am unable find the ROM.nbh file!
CHEEMING.nbh is already there..
What am I doing wrong?
Thanks.
artii said:
Thanks for your info.
sigh..
The rom is an exe file...
I downloaded 7-zip, extracted the rom to a folder.
Looking through it, I am unable find the ROM.nbh file!
CHEEMING.nbh is already there..
What am I doing wrong?
Thanks.
Click to expand...
Click to collapse
Sorry I forgot it was already named CHEEIMG.nbh -- just use it like I said above.
Copy it to the SD card, put the SD card in the device and after you have used Magic_Unlocker , connect via Active Sync and start the CheetahUnlocker process. This will start the three step CheetahUnlock process (really all you need is step one which will put the HardSPL in place) as that process fails the CHEEIMG file on your SD card will get flashed.
Hope this makes sense
Bottom line is that you will be doing an SD flash of the CHEEIMG.nbh file but it takes HardSPL for that to work. Step one of the CheetahUnlocker installs HardSPL (that will be all you need of that process)
remember!
THE SD FLASHING METHOD TAKES A REALLY LONG TIME. SO LONG YOU MIGHT THINK IT'S BROKEN. BUT IT'S NOT!!!!
caps with bold and red= great way to emphasize an important point.
Thanks for the info but I'm still running into trouble.
I copied the file to the SDcard but when running the cheetahunlocker, it give the same error at 0% ( error 206) something about the connection..
I notice that active sync turns off when the cheetah unlocker goes to the coloured screen.
Edit:
Also, should I be moving the CHEEIMG.nbh or just copying it to the SD card?
Thanks.
artii said:
Thaks for the info but I'm still running into trouble.
I copied the file to the SDcard but when running the cheetahunlocker, it give the same error at 0% ( error 206) something about the connection..
I notice that active sync turns off when the cheetah unlocker goes to to the coloured screen.
Click to expand...
Click to collapse
Did you run the MagicUnlocker first?
Is the CHEEIMG.nbh file in the root of your SD card? Try re-formatiing your SD card (FAT32 important!) and then putting the CHEEIMG.nbh file in place on the root of the SD card.
After starting the CheetahUnlocker the TriColor screen should come on and then it should go to a standard White boot scan. It will ask if you want to flash and you will be asked to confirm by pushing the Power button.
If you can ever get Step One to complete on teh Cheetah Unlocker you should be able to confirm that the HardSPL is installed by turing off Today screen (Red, end button) , then hold the left side button while then pushing the reset button. You will get a tricolor screen that lists your SPL version. If it is HardSPL on an unlocked device and there is a CHEEIMG.nbh file on an inserted SD card it will then automatically go to a White boot screen .....
If any of this sounds foreign to you then you need to familiarize yourself in the Wiki re SD flashing
PS do you have the NetFramework 2.0 installed on your PC? When you start the CheetahUnlocker are you getting the Treo device confirmation to install the 2 boot exe files that let the Treo go to the boot screen (you have to answer yes to both of these) - are you making it that far?
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
artii said:
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
Click to expand...
Click to collapse
I'm not sure exactly what is happening in your case but I do know that once a device of any kind enters the bootloader - Active Sync dies - AS is part of the OS and that no longer exists after the bootloader starts, I.e. Windows Mobile isn't really running any longer. the AS connection just gets it started.
I'm not too sure either.
I've unlocked the phone which worked fine.
When I run the cheetahunlocker, it doensn't get past the first step.
Should I be running Hardspl first?
What rom works best with the Treo 750? Link please!!!
What rom are you wanting to use? I have Treo750_WM6.1_WWE_Lite, looking for a more stable rom. Please list some or link them.
I tried both roms
the lite one and the normal one. I must say that the normal one is more stable - with the lite I had to do a reset at least one per day. with the normal version I did not do a reset at all...
Hi, did you resolve this CONNECTION issue? I'm having exactly the same problem.
Anyone?
hey everyone... i have a problem similar to these i think. I'll explain
i've done the magic_unlocker and i can do the 1st step of the cheetahunlocker. treo reset automatically and when i try to flash the rom the trilinear screen doesn't change to the blue screen which is the screen of the rom flash
anybody now why?
i have cracked my head the hole day and a still can't do it :S
artii said:
Yes I ran the unlocker which worked fine.
I formatted the SD card, copied the CHEEMING.NBH to it so it's the only file there.
No I run the CheetahUnlocker.exe , yes to disclaimer , then STEP 1 - I click FLASH SPL, then next, next etc.. I hit Update - next - next then the phone msg comes up asking if I want to run jumpSPL.exe - I hit yes and it goes to the tri colour screen, the active sync dissapears, the screen on the pc stays at 0% and then I get the error 260: Connection, check cable etc..
How is it suppoed to maintain a connection when Active sync turns off?
I did check and framework2.0 is present.
Thanks.
Click to expand...
Click to collapse
If it goes into the bootloader then you should be good to go. Both 750s i unlocked did this. However, if done correctly, the phone should go to a light blue screen where you will press the power button and flashing should begin.
na1kkkk said:
hey everyone... i have a problem similar to these i think. I'll explain
i've done the magic_unlocker and i can do the 1st step of the cheetahunlocker. treo reset automatically and when i try to flash the rom the trilinear screen doesn't change to the blue screen which is the screen of the rom flash
anybody now why?
i have cracked my head the hole day and a still can't do it :S
Click to expand...
Click to collapse
Are you doing the SD method or Desktop? DO the SD method and it should begin flashing right away after the 1st step of cheetahunlocker.
Android on HTC cruise How to?
Hi all,
I'm REALLY confused or misinfomed or whatever on how to run andoid from my sd card.
I tried some things from a website androidonhtc but only got up to a point.
Is there a simple how-to on how to run android on cruise and some links on where to donwload the appropriate files?
For example i have got the haret but i can't find anywhere to download androidinstaller.tar
Am I close or far from my goal?
I know i might ask a silly question but guys i'm really confused.
Thanks anyway in advance.
as for how-to in hxxp://sourceforge.net/apps/trac/androidhtc/wiki/HowToInstall
after getting haretinstall.zip, you need a current kernel (zImage) from
- dzo = hxxp://it029000.massey.ac.nz/vogue/files/?C=M;O=D
or
- sourceforge = hxxp://sourceforge.net/projects/androidhtc/files/
------------------------
as for androidinstall.tar / .tgz you can get from
- vogue forum = hxxp://forum.xda-developers.com/forumdisplay.php?f=588
- kaiser forum = hxxp://forum.xda-developers.com/forumdisplay.php?f=602
- sourceforge = hxxp://sourceforge.net/projects/androidhtc/files/
PS: sorry for the hxxp link, I have no permission to post any link yet
Thank you very very very much for your help!
Congratulations mensa07. Although I already knew all this stuff from your link, it took me some time to figure them out because I did not know there was such a good guide for starters. Very usefull link. Thank you
Hi..
I reading many of threads..
But i still dunno how to make it works on my POLA100..
can any1 show me some guides??
tq..
yes please post a guide for dual booting ...i do not want to flash if not necesary ...
preeety plz
please check this thread for guide on running android on pola100
oh come on ..a couple of links with no explanation ...no nothing ...
its garbage !!! - we have to pick up pieces fom 10 or 12 threads to make this work?and the english is "lakky",,,
please post A GUIDE .... not o joke.
rocket1982 said:
oh come on ..a couple of links with no explanation ...no nothing ...
its garbage !!! - we have to pick up pieces fom 10 or 12 threads to make this work?and the english is "lakky",,,
please post A GUIDE .... not o joke.
Click to expand...
Click to collapse
well, it's no garbage, just required more explanation. let me try to make it simpler. this guide will use zImage-eclair and vaniljeclair, change it to suit your taste accordingly
- get haretinstall.zip from here
extract this file and get default-polaris.txt (rename as default.txt), zImage-eclair (rename as zImage), initrd.gz and haret.exe. put all these files into andboot folder in root of your sdcard. your sdcard will look like this:
/andboot/default.txt
/andboot/zImage
/andboot/initrd.gz
/andboot/haret.exe
- next you need to download vaniljeclair from here
extract the file and you will get androidinstall.tar, put this file along with those files on /andboot/
you should have those 5 files or you cannot boot android.
- select haret.exe to execute, press run, pay attention to the text rolling, when it asks you to hold button, hold volume button up, and you will be given installer menu. choose install and delete data. let the format and installer finish, then you will be given menu again. do not quit, just reset, and restart from haret (you will see that you have data.img, system.img and some other files). at this time let the installer do not interrupt, it took more than 5 minutes before android logo asks you to touch screen
- if there is problem during booting, post it here, let people here try to solve
HTH
i want to ask..izzit it will wide out my windows mobile system??
scotty89 said:
i want to ask..izzit it will wide out my windows mobile system??
Click to expand...
Click to collapse
no, if you start android from haret.exe, it will not erase anything.
even data in the sd card??
scotty89 said:
even data in the sd card??
Click to expand...
Click to collapse
it will not erase your sd card either, however you might want to backup your data first just in case something does not go well.
thx for ur help..
i get to boot in the android..
try to use it..
is the bluetooth and wireless fix>??
and can the contact to be sync??
scotty89 said:
thx for ur help..
i get to boot in the android..
try to use it..
is the bluetooth and wireless fix>??
and can the contact to be sync??
Click to expand...
Click to collapse
BT and WIFI should work, there is vaniljeclair thread on this problem if something is not working.
as for contact I think you need google account to sync.
Hi,
Thank you for the guide. I actually follow it and encountered an error. When it asked for volume up or d-pad center, I did, then it prompted that it was waiting for something several times. So I soft-reset the phone and launch it again.
Then, after haret.exe is booting linux, I have got a strange screen with scramble text.
How can I put everything back in the previous state to reinstall it propely?
Thank you
More info....
Did you get to the install screen after pressing centerdpad?
If yes, did it install?
What was it waiting for? The error message can give a clue what is wrong.
i manage to get to ask to hold up the center d-pad then get into a installer menu..
currently i just cant get my wifi and bt work..
haven get connection to sign in to google account..
I have all five file on my SD card but when I click on haret on my Sd and hit run where it say defaukt.txt..I get a error saying " cannot open script file \storage card\andboot\default.txt" is im doing something wrong..thx
u got change the polaris default-polaris to default??