palm treo 750 ROM completely dead - Palm Treo 750

The only thing my treo 750 is showing when I do a reset+button is:
Palm Tr
IPL-0.20
Palm Tr
SPL-0.24.0000
Serial
if I connect the USB, it changes Serial to USB.
I can´t fo anything at that point. If I put the CHEEIMG.nbh in the SD card and try to reboot, I only got a black screen. If I try to run the romupdateutility it ends with a communication error.
please help...

Did you try a hard reset or a soft reset? If all you did was the soft reset, try a hard reset.
Also, you haven't successfully HardSPL'd your phone based on the SPL (SPL-0.24.0000) you are showing in your post. You won't be able to flash a ROM via SD card without a successful Hard SPL.

trukis to facilitate and verify which one did you decided to illustrate!
Soft and Hard Reset on Treo750:
Soft Reset
In Palm Treo 750 can be done soft reset by quickly pressing the small reset button labeled below the slot for miniSD memory card:
Hard Reset
A Hard Reset will erase all internal memory and returns the Treo its factory specification.
All data entered, preferences or software installed on your Treo will be deleted.
To do the Hard Reset, just press the reset button - above - simultaneously with the red "End" - Off (as shown below) Press and hold both buttons until the screen completely disappear.
When the screen comes back you will see the option to "Erase all data." Select Yes to complete the hard reset.

I have the same trouble with my treo 750.. I tried hard and soft resets but the device falls again in the tri-color screen.
Is there a method to send terminal emulation commands with some kind of software being in that mode?
Please help.

you´d better googlefy - there are some topics on ppcgeek´s web pages with download links that should provide tool able to unlock in bootloader.. personally I never had such problem - I simply went here on xda forum, used treo 750 wiki and then I succesfully flashed to wm 6.1 .

Related

JamIN rom update - loader screen

Hey all.
I have successfully managed to edit my jamIN extedendrom.
But... when I hard-reset the device to load the new extrom, the "loader screen" comes up showing what is installing etc.
The problem I have is this: One of my cab files installs antivirus software, but you need to tap "accept" before the software installs.
Because of the fact that this "loader" screen is in the way, I cannot tap accept and the rom installation just hangs there.
Is there any way to remove this loader screen, or make it go to the back whenever a popup comes up?
Thanx in advance!
You could try hard resetting your phone, after the screen alignment setup you get 3 seconds warning about loading the EXT ROM, just soft reset. You won't get the software from the EXT ROM, but at least you can edit the ROM again.
All the best

NBD 8.0 Won't start, A little help

I flashed to NBD 8.0 about a week ago and have been loving it's sweetness. Today though, I turn on my wizard and it won't get past the NBD startup screen. I have reset and taken out the batter a few times now to no avail. Can anyone help?
Could it be... dare I say.. Bricked.
Can't even do a hard reset.
Your gonna have to do a hard reset. i've had the same, but search to NBD8.0 forum the procedure is there if you can't google it for hard reset of your device. also try to keep your reply/questions in that particular post and try not create a post when one already exsits for the rom your using. They stress the fact that you must read before asking a question that's been asked a thousand times.
wade_link said:
Could it be... dare I say.. Bricked.
Can't even do a hard reset.
Click to expand...
Click to collapse
I had the same problem with a different rom, but the same OS. If you see the boot splash screen, and the boot stops in there, press the power button and keep it press when you notice that the boots hangs up. it might power off you device, o bring it to life.
To do a hard reset on a wizard, you must press the comm button + voice dial button + reset button (with the stylus).
Then press send when the screen ask for it.
NBD 8.0 Won't stuck at the 3rd - PLEASE HELP!
I loaded the 8.0 last Friday. Last night, I rebooted the MDA and it stuck at the 3rd screen. Tried hard reset and got no responses. Also, tried to get the lhe bootloader (3 colors) screen - no reponses either. CAN ANYONE HELP!
Thanks
kmlworld said:
I loaded the 8.0 last Friday. Last night, I rebooted the MDA and it stuck at the 3rd screen. Tried hard reset and got no responses. Also, tried to get the lhe bootloader (3 colors) screen - no reponses either. CAN ANYONE HELP!
Thanks
Click to expand...
Click to collapse
Did you remove your SD card, sometimes that helps
Eelco
while doing your hard reset, don't let go of the two buttons after you have used the sylus.
NDB 8.0 stuck at the 3rd screen- PLEASE HELP!
I tried to remove the SD and SIM card - but it still doesn't work. No matter how I tried, I can't seem to able to get the the bootloader (3 colors) screens.
Thanks in advanced for your guys help!
kmlworld
I have the same problem too on v7.9 and v8.0. I've soft resetted the next day, and it always gets stuck on the 3rd splash screen. I tested this out a couple of times. But when I was using v7.4 I never had that problem.
I just had the same problem (stuck on NBD screen) with 7.9, after trying to access an html file saved on the sd card. A hard-reset solved the problem (after some brick-scare time, though ... )
the problem I have is I can't even get pass the 3rd screens. soft-reset and hard reset did not help. Tried to get the the bootload to reload the os but CAN'T.
The problem I have is I can't get pass the 3rd screen. Hard or soft resets didnot help. I want to reload the OS but CANT get to the bootloader screen. Tried all combination of keys that described on this forum. Anyone has any other ideas?
kmlworld said:
The problem I have is I can't get pass the 3rd screen. Hard or soft resets didnot help. I want to reload the OS but CANT get to the bootloader screen. Tried all combination of keys that described on this forum. Anyone has any other ideas?
Click to expand...
Click to collapse
this should work:
- turn it off
- remove sd card
- while pressing the voicedial button turn it on (keep pressing the voicedial button till bootscreen appears)
- reflash os
It would help me a little if those who are having this problems gives more details (g3 or g4, ipl/spl version, extra software installed, do they use touch version or not)
Zoki, here are my details : NBD 7.9 touch on a G3, IPL/SPL 2.26, GSM 2.11 (the t-mobile version, i flashed the 2.69 version since) running BatteryStatus 1.04.201 beta3. Nothing more installed except tom tom 6.02 and opera mini 4 beta. I was browsing the minisd card with the built-in file explorer to open an html file with IE when it completely froze.
I tried holding the power button in order for it to reset, to no avail. I popped out the battery, remove the sd card, but it stuck on boot on the NBD screen. After trying several times, I hard-reset it, and it worked.
I count on upgrading to ipl/spl 3.08 before installing NBD 8.1.
Update: I flash on a laptop computer running XP Pro, and before installing NBD 7.9 I flushed the t-mobile 2.26 version, as recommended somewhere in this forum. Last program I installed, several hours before the freeze (and forgot to mention) was Deepfish (latest version).
Zoki, i am ready to help if you need to run tests/debug/log, thank you very much for your work !
Is the lock up happening after you install software?
I have experienced the same issue when I install any third party software into NBD V8. I think this is one of the best ROMs I have worked with and tested other than this issue.
zoki said:
It would help me a little if those who are having this problems gives more details (g3 or g4, ipl/spl version, extra software installed, do they use touch version or not)
Click to expand...
Click to collapse
My is a G3 Version.
CID Unlocked
IPL/SPL Versions 2.25
Base Rom V8, No changes, TouchFlo enabled
installed via ShellTool
OS of host machine: Vista Ultimate with XP HTC device drivers.
Issues installed when installing any cab file or installation from Active sync.
I had to do a reset and then I noticed it locks up in the NBD screen. The issue can only be resolved with a hard reset.
Hope this helps... Will be looking for any input and if I can help in any way! PM me!
Here is my setup
Mine is a G3 Version.
CID Unlocked
IPL/SPL Versions 3.08
Radio 2.19 and 2.69 (tried both w/ same problem)
Base Rom V8, No changes, TouchFlo enabled
I have installed:
Bluetooth Headphones
Hardware GPS unit
Coreplayer
iGo Myway gps software
Piscel Browser
Now I have tried to test it out to see what is making the system freeze on that 3rd screen. So I installed each of those programs. Then I do a soft reset. It starts up fine each time. My problem seems to happen like the next day or so. If I soft reset the next day, then it will freeze. So i'm not totally sure if it's 3rd party software or not. When I was using his 7.4, I had all these programs installed and no problems with soft reset.
I've done the take out SD Card, reboot and whatnot. Same problem. The only thing that works for me is to either Hard reset (holding comm manager button, voice record button + reset button) or to go into boot mode (power button + camera button + reset) and do the reflash.
Bottom line is though, it's a great rom, i love it. Having it freeze isn't totally a big deal to me, since I keep my stuff backed up through the PIM. I think I just need to stay away from doing soft resets. Hopefully someone will figure out what is going on with it. But for now i'm fine with it.
nbd screen hangup
zoki said:
It would help me a little if those who are having this problems gives more details (g3 or g4, ipl/spl version, extra software installed, do they use touch version or not)
Click to expand...
Click to collapse
G4-device IPL+SPL 2.21.001.
Radio 2.69faria.
batterystatus v3, touch.
After softreset it hangsup.
HELP!!
Can't get the the bootloader screen
Anyone know how to get to the bootloader (3 colors) screen? I tried the power+talk+reset, comm+talk+reset, messaging+ie+reset, etc. - none seem to work. Anyone has other ideas?

severe problem with my vox

hi everyone. yesterday i installed dr. gonzo's wm6.1 rom in my VOX. it was great and it worked perfectly in my phone.
The main problem started when i restored the backuped data. I took, This backup with sprite backup tool before upgrading my mobile from wm6.0 to wm6.1. when i restored this data taken in version 6.0, in version 6.1, i found that my homescreen is blank. whenever i press start button i find the following message display on my screen: Cant Find ':MSSTART' (or one of its components). MAKE SURE THAT THE PATH AND FILENAME ARE CORRECT AND THAT ALL THE LIBRARIES ARE AVAILABLE.
The same messge appears when i press any numeric key replacing MSSTAART with MSCDIAL.
Actually, when i backuped the data it also backuped the registry settings and when i restored the data it applied version 6.0 registry settings to version 6.1.
Now, neither my phone is getting connected to the activesync nor it is getting HARD RESET(I tried many times to Hard Reset it, but never succeeded. What happens is that as soon as i press the POWER button while holding both the soft keys, the phone TURNS OFF).
Please cananyboby help me? can anybody tell me that is there any other way to hard reset? or, how can i restore the phone back to factory settings?
Thanks for understanding my problem so patiently.
hoping to get a solution soon.
thanks
Get the battery out for a few seconds and put it back, and then do a hard reset.
But I think that you are not doing hard reset correctly, you have to press power button and both soft keys while your phone is turned OFF, then your phone will ask you to pres green button and it will do a hard reset.
must press the green dail key to comfirm the reset operation
error in uPgrading the ROM
Ive tried many times to hard reset but it dosent seems to take place. i tried to reflash my phone from the bootloader mode but it dosent seem to fi my problem. it showed an error while reflashing stating IMAGE FILE IS CORRUPT. IVE attached an image of that error.
any help???
LOL~~~
I see, first shut down your s710, hold the 2 soft keys
and then press the power button shortly (must not too long)
ive performed hardreset 3 times earlier but this time i cant hard reset just because of the problem. the problem is that none of its functions are working. i really need some help this time!!!
I am using this rom, it can be hardset by this method.
hold the 2 soft keys utill dialog show, press the power about 1.5-2 sec.
Hard reset capabilities are not dependant on the ROM. You need to properly flash with a signed HTC ROM or USPL and then an unsigned ROM. I don't think you're doing the proper steps involved to hard reset or to flash correctly. Re-read the Wiki.
Problem Solved
I was trying to flash 6.1 version after the problem occured so it showed IMAGE FILE currupt. Then I tried to flash the original(manufacturer's) version in the bootloader mode. everything went properly and my vox flashed perfectly.Now i've once again flashed the 6.1 version and is working great.
'My hearty Thanks' to everyone for the help and support.

i-mate JAQ restart problem please help

HOW TO FLASH, HARD RESET i-mate JAQ, please help
--------------------------------------------------------------------------------
i-mate JAQ restart problem, how to hard reset or flash this phone, please help. How to get into bootloader mode please help all respected members. Can i flash with JAF WMA to this phone?
Finally I've found.
from http://www.amazon.com/i-mate-JAQ-Smartphone-Unlocked/dp/B000KI71BS
and also http://forums.cnet.com/5208-6140_102-0.html?forumID=57&threadID=254732&messageID=2529411
I'll simple copy and paste:
- Factory reset is accomplished via software in the "Settings" folder. There is no provision for a hardware "hard" reset. This means that if the device won't boot for some reason, you are out of luck. Most devices have a certain sequence such as "Reset + Power + Volume" or some such, to allow a factory or "hard" reset if the device is locked up entirely. Removing the battery will not perform a hard reset. As a matter of fact, this exact situation occurred; my JAQ would not respond to the Settings -> Factory Reset Icon. I discovered that the device can be reset by pressing RESET, IMMEDIATELY followed by pressing the Fn Key + the right-hand soft key for 6 seconds. This will force a hard reset.
Found this took me about 5 months!
It's hard to find information on the JAQ since it's not made by HTC. i-mate is based in Dubai, and it's even harder to get information out of them. Their forums are terrible.
my imate jaq's battery shows 0% even then it works for 32 hrs continously... what to do .... reply on email pz .. [email protected]
i want to reflash the imate jaq.........itz wm5 .........where can i get the rom for dat....
i have some problem plz help
i want full flash I MATE JAQ
any body help me ???????????
i still havent got any solution for hard reset how is that?

Bootloader can't load

Help meee!
I've just installed advanced confirutaion tools 3. My mobile phone is HTC 3300 (Artemis). So, I tried MAKING SOME system tunings with this program.Then it asked me to reboot system to activate modifications. I pressed "Ok" and it switched off. Then I tried to switch it on. So my phone swithed on, label HTC appeared, and after it phone swithched off again =(
And so on so on...
Then I decided make a hard reset, but bootloader can't load completely. There appears tricolor, IPL xxxx SPL xxxx USB. and then buzz =( It doesn't react at any actions, just on soft reset or hard reset. Then I however loaded bootlader: it asked me to press "send",if I agree to restore all data. I pressed it, there poped-up a message,informing me about successful operation and the phone switched off again =(((
What I must do? I just want to recover my system =(
Thanks a lot for help!

Categories

Resources