Okay so I recently updated my Ipaq hx4700 to 6.1 Alkor Build 21054 and installed MobileSRC's Mobile Remote v1.1 on it. I want to use it as a bluetooth remote for my PS3 but I keep getting two errors over and over again:
Error 1 (shown at boot up of mobile remote): Failed to load driver: 87
Error 2 (shown after selecting legacy mode, and then checkmark to begin connecting):
Error Connecting: [1062] Listen INTR failed
There was an error connecting to the computer. Please ensure that your computer is on, has Bluetooth enabled, and has an active pairing with this machine.
Any help is much appreciated.
Thanx in advance
Related
When connecting my PC to the Phone using add new connection wizard I get the following message after the Laptop finds the phone and I enter in the security code: "Installing a modem on COM40"
Then it comes the message "Automatic modem installation failed
Please set up again"
I'm using:
Sony VAIO VGN sz460N
Windows Vista
Nokia 6125
Any advice or suggestions would be appreciated.
Thank you
Hi All,
I am unable to install WMDC 6.1 on Vista x86 SP2 (with all updates installed till date). Whenever I am trying to install - it says:
Atleast one of the Windows component required by WMDC is missing.
When I am connecting the device without installing - it is saying :
"Windows Mobile-based device"
The Class installer has denied the request to install or upgrade this device.
My System:
Toshiba Satellite A40 (P4 M 2.66 / 768 MB/ 80 GB) / Vista x86 SP2 / ESET NOD32 Antivirus.
I have tried disabling AV as well as firewall. Still the same result.
This happens with both my HTC Vox and Samsung B7320. Any help will be appreciated.
Thanks in Advance
Bump
Sorry, just bumping up to top
i just tried to update my HTC PU10 windows mobile 5 to WM6 but then the screen got blank and now i think its in boot loader screen as i read in most of the forums. i read most of the forums abt this for 7hrs now and still stuck coz im new to these.
im using windows 7 on my pc so i cant use Activesync so im using windows mobile device center to connect
i tried connecting to mtty1.42 but my MDA dosnt detect in USB as most of the forums say but when i connect to the pc my MDA screen gose serial to USB v1.01 it mean im in the boot loader screen am i right ? so please tell me wht to do next
thanks in advance
Mudith
Welcome to forums
Have a read on the Wiki here:
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Hope it helps,
ok i got my MDA working have to use Windows XP. ROM Update Utility dosnt detect the MDA from USB on Windows7
Windows XP is the best
thanks guys for ur support
hy mudith
i have the same problem with my pda...so please tell me what to do next...i read on forums but my pda doesn't connect on my pc....!!! i don't know what should i do..!!!
Belated Help
Firstly, remove both the SIM card and any memory card. Make sure your battery is charged as well. Can you get into the bootloader (Light button, on/off button and reset button all at the same time)?
If so then your screen should be showing 'Serial' at the top and a number at the bottom. Plug the cable into the XDA and into your PC (it IS a PC and not an iMac I'm assuming?). What OS are you using? XP, Vista or 7?
You need to ensure that 'connect via USB' is DE-SELECTED in either activesync or Windows mobile device centre.
With the cable plugged in, the 'serial' should change to 'USB'. If so all is good. If not, try another cable!
You may also need to ensure you have the correct drivers loaded for Vista and Win 7. I can't get it to work under Win 7 but I can under Vista. XP is preferred for stability for me though.
Now, assuming you have USB on the XDA screen, run mtty (attached to this post) and select usb as the connection type.
Then press enter and you should get a 'USB>' command prompt in the window on the PC. Type (not copy paste) the following:
set 14 0 <press return - don't type this bit obviously!>
Task 28 55aa <press return - don't type this bit obviously!>
Allow each to finish before typing the next and allow the command prompt to appear before exiting.
Then exit mtty and flash a good ROM, I use VNInt with HomeScreenPlus.
Good Luck!
During the upgrade of jasjar to wm6.5
After synchronization by activesynic and format the old version
Restart the machine work and entered the boot Loader system
Screen appears, written by usb from the top and bottom of v1.00
And a message from windows xp says usb device not recognised
And stop everything ....
I tried to install the driver of the usb from the cd but the pc does not accept
also tried more pc by xp, seven, vista
But the same thing ....
What is the solution
Hi everyone.
Firs of all, excuse me, cause i'm a newbie at the topic.
My question is "simple": How to flash *anything* to a mobile device based on WIN CE without drivers on windows or linux?
Much further details:
The device is the Kin phone, based on windows mobile 6.5.
Device is connected by USB to the pc.
No activesync / windows mobile device center connection is available (no driver and so).
We can start the device in SBL mode (secure boot loader?), so able to flash IPL,OS,Radio and splash image (according to coinflipper leaked rom analysis).
We got the VID and PID for the product in the SBL mode: V 0x045e; P 0x2345
"lsbusb -vv" on the device shows 2 endpoints, 1 for bulk transfer in, other for out.
Using raw c++ i was able to write and read succesfully on the device endpoint but whatever i sent to it was just answered with a "0x01" as response.
So if the winCE masters here can enlight the thing a little, it will be much appreciated.
Thanks in advance,
John K.