Related
My roommate bought an EVO 4G off Craigslist that was pre-flashed to MetroPCS. It had a clean ESN, so I tried to have it activated. I finally got voice and text to work, but no data. After searching the web, visiting flashing stores, and spending hours on the phone with Sprint's so called "Technical Support" over the last week, I finally figured it out...
This is my first tutorial, so bare with me. And I apologize if this is in the wrong forum, it seemed most appropriate. I performed all this in Windows 7 x64.
First you need some software-
1. QPST - http://www.mediafire.com/?m4s81a4zsdbmhen
2. HTC Diag phone drivers - http://www.mediafire.com/?631456zwxi09hh2
3. PRL File 60650 - http://www.corolada.com/prl/
4. I'm not sure if you need ADB installed, but I already did.
5. You will also need to know your MSL. It will most likely be 000000 if your phone is coming from Cricket or MetroPCS.
Now that we have those, we can get to work.
6. Connect your phone via USB and type in ##3424#, your phone should now be in Diag mode. Make sure USB Debugging is ENABLED!
7. Open your device manager in Windows and right click the unknown device "HTC DIAG", Select Update driver.
8. Select Browse my computer for driver. Click select device from list, Click next, Then click "Have Disk" and point to the appropriate HTC Diag driver folder you downloaded.
9. You now should have HTC Modem installed correctly. Right click on it and go to Properties, Then click on the modem tab. Find your port number eg. COM1, COM2, etc.
10. Open up QPST Configuration, Click the PORTS tab. On the bottom right click add port. Add the port you just found from the step above, and hit Enable.
11. Go back to the active phones tab, double click your phone.
12. On the bottom click read from phone. Then save it for a backup.
13. Click on Roaming tab. Find the PRL box, click browse and add your 60650 PRL file you downloaded.
14. Go back to the CDMA tab. Under phone number click the Class 1 box. Enter your phone number (xxx-xxx-xxxx) minus dashes in the box next to Class 1.
15. Click write to phone. Hard parts over!
16. Once that finishes, unplug and reboot your phone.
17. Go to Settings>Update Software>Update PRL then reboot again.
17. Once its back up go into your dialer. Punch in ##3282#. Hit Edit Mode. The password is your MSL.
18. Once in goto Data Profile. Hit Menu then hit RESET.
19. Your phone should now reboot and be able to activate on Sprints network!
I already did this for my roommate, so I am writing this out of memory. I wanted to post pictures but I would have to take CM7 off my phone and redo all of it... grrrr.
Again, this is my first guide so i might have missed something. But I hope not. So many people have helped me here on XDA, so this is my contribution to the community. I hope this helps some people.
I did this to a hero. I believe I just cleared all the ##data stuff and pep update manually.
Sent from my PC36100 using Tapatalk
I tried that to. But the only way to make it work was to flash the new PRL file. Neither Sprint or a Cricket flashing place could fix it. Which I thought was pretty stupid.
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
This is handy to have, and even better to have a few different ways to do it.
amoamare said:
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
Click to expand...
Click to collapse
Beat me to it.................. This will definitely work.
amoamare said:
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
Click to expand...
Click to collapse
thanks to all. this worked for me.
followed the guide, however data and market place is not working
calls and text work fine, any ideas ? thanks
amoamare said:
Another quick way of doing it.
Load Stock RUU.
This will rewrite PRL, NV items etc back as it rewrites the radio wich controls these.
Once done ##RTN# need MSL to use this, but this will help as well. and your done.
Click to expand...
Click to collapse
I tried this like 4 times, and it would never flash the PRL... the way I did it, it finally flashed sprints PRL.
brax said:
followed the guide, however data and market place is not working
calls and text work fine, any ideas ? thanks
Click to expand...
Click to collapse
Go into your phone settings, goto About Phone, what is the PRL number listed?
i am pretty sure i flashed the "60650.prl"
however i sold the phone and it will be back here tomorrow for repairs....
i had the guy do the settings -> update prl without luck....
sigh thanks for any help!
brax said:
i am pretty sure i flashed the "60650.prl"
however i sold the phone and it will be back here tomorrow for repairs....
i had the guy do the settings -> update prl without luck....
sigh thanks for any help!
Click to expand...
Click to collapse
Well if for some reason it didn't flash, then "update PRL" wont work cause its not looking for sprints PRL. Try to see what PRL is loaded on the phone, then I can probably help a little better.
guy claims under settings the prl says 1.77-003
thanks
brax said:
guy claims under settings the prl says 1.77-003
thanks
Click to expand...
Click to collapse
That's the PRI, not PRL. The PRL will be a five digit number. The latest Sprint PRL is 60675.
yeah thats what i figured, didnt know if that was a hex abbreviation with sprint's software for the prl or what... waiting for him to text me back...
i am pretty sure when i waited for him to activate the phone it showed a 3g icon when voice and text went active.. you sure if the prl is wrong everything else would work except data/mms/marketplace? thanks
the prl is = 60675
brax said:
yeah thats what i figured, didnt know if that was a hex abbreviation with sprint's software for the prl or what... waiting for him to text me back...
i am pretty sure when i waited for him to activate the phone it showed a 3g icon when voice and text went active.. you sure if the prl is wrong everything else would work except data/mms/marketplace? thanks
the prl is = 60675
Click to expand...
Click to collapse
Well you have a Sprint PRL. Did the phone go through the Hands Free Activation when you tried to activate it? If you see a 3G symbol then all should be good. You could have him call Sprint and tell them data isn't working and you need to re-activate it...
well we had to type in a diag code then hit update and then it activated, not OTA to get talk and text going... he said he spent a hour at the sprint store today and they couldnt solve it
You could try my guide again, from step 17.
i asked the guy via text to do the guide through 17 to end, he says they tried that at the sprint store... without luck... i guess i can try it tomorrow when the phones in my hands unless anyone else has any other ideas....
what i did was followed this guide after flashing a oem RUU back to the phone
"RUU_Supersonic_1.47.651.1_Radio_2.05.00.06.10_release_CL195459"
Did you get your phone working? Could you share some of your tricks? Thanks!
brax said:
what i did was followed this guide after flashing a oem RUU back to the phone
"RUU_Supersonic_1.47.651.1_Radio_2.05.00.06.10_release_CL195459"
Click to expand...
Click to collapse
i have a charge in europe and i want to use it as a console,player,etc...but its allways searching an 4g sim or something like that...how can i use it witout that?thanks in advance and apologise if i did smting wrong,im first time here
mindandminds said:
i have a charge in europe and i want to use it as a console,player,etc...but its allways searching an 4g sim or something like that...how can i use it witout that?thanks in advance and apologise if i did smting wrong,im first time here
Click to expand...
Click to collapse
Maybe go into the drop down menu at the top of the screen and disable data so 3g/4g isnt present or go into settings mobile networks and un select use packet data.
blueis300 said:
Maybe go into the drop down menu at the top of the screen and disable data so 3g/4g isnt present or go into settings mobile networks and un select use packet data.
Click to expand...
Click to collapse
its not helping...it ask me to select the language,than say SORRY,THIS SIM CARD IS NOT SUPPORTED OR READABLE.PLEASE CONTACT YOUR WIRELESS SERVICE PROVIDER.....i tried whith and without a sim inside...i plug the usb data cable and i cant even acces the internal memory...please help,it got to be a solution
So your phone was never setup before? I just took my sim card out and started and I could change and it worked.
---------- Post added at 04:16 AM ---------- Previous post was at 04:14 AM ----------
blueis300 said:
So your phone was never setup before? I just took my sim card out and started and I could change and it worked.
Click to expand...
Click to collapse
Maybe start the setup process, select english, next , skip back up assistant,either enter a gmail account or fake and see if you can get as far as you can just to get into the settings.
Ok what screen are you seeing can you do anything? Some company's can unlock the phone so u enter ur country code I guess then maybe bypass setup.Maybe have a friend that has a setup sim card for your country put in the phone just to pass the setup screen then there are several options to continue.
If you can get to a keypad screen,
Try this:
1. Select emergency call and dial ##778.
2. Select edit and enter service password 000000.
3. Select NAM Settings.
4. Change Mobile Directory number to 0000000000 (Ten digits).
5. Change MIN1 to 0000000 (Seven digits).
6. Change Mobile Country Code to 000 (Three digits).
7. As you back out "Commit the Change".
blueis300 said:
So your phone was never setup before? I just took my sim card out and started and I could change and it worked.
---------- Post added at 04:16 AM ---------- Previous post was at 04:14 AM ----------
Maybe start the setup process, select english, next , skip back up assistant,either enter a gmail account or fake and see if you can get as far as you can just to get into the settings.
Click to expand...
Click to collapse
my phone is new,and i cant skip the asistant,because its not setup...i cant enter the menu at all,after i select english its teling me that message about the sim
It worked a while for me until it recognized that there was no SIM card in which case it locked up again but just did the
Press the emergency call button.
Then dial *#83786633
Press the home key.
method and it bypasses the SIM activation for a while again.
No keypad or picture of a droid? Ive read several posts that if you can stick a valid sim card in even if its not your I would assume from the country you bought the phone you can bypass setup.If bought in the US use any active sim card and then bypass everything.
---------- Post added at 04:57 AM ---------- Previous post was at 04:50 AM ----------
Read another option, get a prepaid sim card from your country to help get past the no sim card and then disable the sim card check without continue as setup as you dont want to use as phone and cant.
http://forum.xda-developers.com/archive/index.php/t-1080753.html
Can you show me the actual screen and I can search from there?
just before your post,i find the same method on the other frum,here on xda....thank you very much,you guys are awsome...what is the thing with thanks meter?because i want to thank you...P.S.the phone is awsome!!!
On the bottom of this post it says thanks quote etc... Just hit thanks button. Or whatever you already said it. Glad you got it to happen. Had 2 other ideas but to dang early. Gonna try and sleep some more.
blueis300 said:
On the bottom of this post it says thanks quote etc... Just hit thanks button. Or whatever you already said it. Glad you got it to happen. Had 2 other ideas but to dang early. Gonna try and sleep some more.
Click to expand...
Click to collapse
If i manage to root the phone and install a custom firmware,i still have to enter in testmode every time i start the phone?well,for me isnt realy a phone,is a mini tablet...
Yeah I think so as you wipe everything and it wants to do some type of setup.
So,i cant get rid of the verizon apps and the bypass process in any way?
Sent from my SCH-I510 using XDA App
mindandminds said:
So,i cant get rid of the verizon apps and the bypass process in any way?
Sent from my SCH-I510 using XDA App
Click to expand...
Click to collapse
If you can bypass the setup process like you said you would just install a rooted rom that is either debloated or download a program to unistall or freeze them. So basically use ODIN to install debloated Rom and then you can do whatever you want. To be honest I havent really paid attention as Ive changed my phone so many times but even with rooted roms I think you would still need to bypass setup and like I said then you can do whatever you want.Didnt you say you had bypassed the setup process?
Just read you post #9 so you were referring to entering test mode everytime you restart your phone. Dont know didnt do anymore research as you said you had it working. I would have to google more an look it up. Maybe someone else might know more?
I am trying to install NextGen 1.5
Problem is, in main menu, whenever I go to "recovery", fone gets struck with htc logo(white background). Then I have to take out battery, re-insert, press vol down+power up .....fast boot and run "recovery.bat" from pc(while connected fone to pc). then I get back the CWM Recovery Menu.
This is occuring everytime. Please help me to fix it.
Try with some other recovery, it's not like you don't have a choice And from which main menu you're getting in to recovery?
shortyoko said:
Try with some other recovery, it's not like you don't have a choice And from which main menu you're getting in to recovery?
Click to expand...
Click to collapse
well "main menu" refers to vol down+power button, which leads to "fast boot, recovery, factory reset" options.
Also u only suggest me some better recovery plz.
http://forum.xda-developers.com/showthread.php?t=2123503
I don't know if it's better or not, I'm still with the good old yannou's recovery, staying with the principle 'if it aint broke, don't fix it'
shortyoko said:
http://forum.xda-developers.com/showthread.php?t=2123503
I don't know if it's better or not, I'm still with the good old yannou's recovery, staying with the principle 'if it aint broke, don't fix it'
Click to expand...
Click to collapse
Thanks buddy...1 more thing, I hv installed nextgen1.5 Now when i go to music player-->sound enhancer..i get a FC, can u help me wid dis ?
Plus when i try to grant SU permission to any app..it says "Sorry, test failed. This feature cannot be granted to ur fone"
Fone is perfectly rooted. Had been using it for 1 yr, n now for the frst tym put custom rom and all these issues.
That's for the dsp
.Music player force closes bcoz of DSP libraries to fix just remove the library file from /system/lib/soundfx/libcyanogen-dsp.so it will perfectly like breeze.
Click to expand...
Click to collapse
For super user, enable usb debugging option from the phone menu(at the moment I don't remember where it was in the menu)
shortyoko said:
That's for the dsp
For super user, enable usb debugging option from the phone menu(at the moment I don't remember where it was in the menu)
Click to expand...
Click to collapse
Thanks a ton ! worked like charm ! +1
If u dont mind, tell me from where did u get that solution for music player ? I was looking for that but google dint help >_<
From NExtGen thread, when firstly 1.5 was released this was kind'a annoying bug, so there was a lot of question about that, here is the specific post from where I took it > http://forum.xda-developers.com/showthread.php?p=33599083&highlight=1+5+dsp+fix#post33599083
Just a friendly advice for the next time, there is a 'search in this thread' function which is really helpful when you have an issue with, whichever rom, cos it's possible for somebody to yell at you if you asked something that has been answered several times before
shortyoko said:
From NExtGen thread, when firstly 1.5 was released this was kind'a annoying bug, so there was a lot of question about that, here is the specific post from where I took it > http://forum.xda-developers.com/showthread.php?p=33599083&highlight=1+5+dsp+fix#post33599083
Just a friendly advice for the next time, there is a 'search in this thread' function which is really helpful when you have an issue with, whichever rom, cos it's possible for somebody to yell at you if you asked something that has been answered several times before
Click to expand...
Click to collapse
will keep that in mind thought google was more accurate, but oh well !
Help?
You got your answer bro, or still need help....
Sorry i checked PM today so didn't reply...:good:
artistaditya said:
You got your answer bro, or still need help....
Sorry i checked PM today so didn't reply...:good:
Click to expand...
Click to collapse
its fine, shortyoko helped me. You may edit the thread name with [solved] tag
try another custom rom
Recently I got my Moto G and I was trying out new roms and now for some reason my device does not connect to the carrier.
Under Setting > About Phone > Status > it says...
Network = Unknown
Mobile network type = Unknown
Service State = Radio Off
Mobile Network State = Disconnected
I tried to go back to stock and Wifi is working so I know the radio is not fried or something.
Basic things I have already tried include:
Reboot the device.
Flash back to stock as mentioned before. (multiple times)
I tested the SIM card and it works as well.
Tried to turn on and off the Airplane mode.
I dont know what to do and I cant find any threads on a similar problem so if someone can please help me it'd be appreciated. Thank you.
jeety4079 said:
Recently I got my Moto G and I was trying out new roms and now for some reason my device does not connect to the carrier.
Under Setting > About Phone > Status > it says...
Network = Unknown
Mobile network type = Unknown
Service State = Radio Off
Mobile Network State = Disconnected
I tried to go back to stock and Wifi is working so I know the radio is not fried or something.
Basic things I have already tried include:
Reboot the device.
Flash back to stock as mentioned before. (multiple times)
I tested the SIM card and it works as well.
Tried to turn on and off the Airplane mode.
I dont know what to do and I cant find any threads on a similar problem so if someone can please help me it'd be appreciated. Thank you.
Click to expand...
Click to collapse
Are you in India? Using a dual-sim?
https://forums.motorola.com/posts/027c60e48f
Landrea said:
Are you in India? Using a dual-sim?
Click to expand...
Click to collapse
No I am in the US with T-Mobile. And I have the single sim version.
I can't be helpful here.
I only can suggest to look at this thread and try to flash some radios...
http://forum.xda-developers.com/showthread.php?t=2649763
Sent from my Commodore 64 using Videotel
Landrea said:
I can't be helpful here.
I only can suggest to look at this thread and try to flash some radios...
Sent from my Commodore 64 using Videotel
Click to expand...
Click to collapse
Thanks for trying anyhow. I have already tried both the radios for my phone (XT1034) and then even the 1032 version just in case. Then On a custom rom I was able to get into the radio settings by dialing *#*#4636#*#* and realized that my IMEI is set to 0's
I searched to see if this was normal and found out on a lot of other devices people have had similar issues but so far still havent found a way to resolve the problem.
jeety4079 said:
Thanks for trying anyhow. I have already tried both the radios for my phone (XT1034) and then even the 1032 version just in case. Then On a custom rom I was able to get into the radio settings by dialing *#*#4636#*#* and realized that my IMEI is set to 0's
I searched to see if this was normal and found out on a lot of other devices people have had similar issues but so far still havent found a way to resolve the problem.
Click to expand...
Click to collapse
Curious to know if you found a solution - I've just started researching this problem, so hopefully I'll find an answer somewhere else, but if you solved your problem, let me/us know how...
Solution
lhuge said:
Curious to know if you found a solution - I've just started researching this problem, so hopefully I'll find an answer somewhere else, but if you solved your problem, let me/us know how...
Click to expand...
Click to collapse
Yes I did find a solution. I flashed the Android 4.3 stock image with adb fastboot. And then reRooted and installed cwm again and it works like normal again. When I get home in about 8 hours I will try to post Dropbox links to the stock image and the instructions I used.
The last solution is reinstal your device.But don't forget to recover your data.
jeety4079 said:
Yes I did find a solution. I flashed the Android 4.3 stock image with adb fastboot. And then reRooted and installed cwm again and it works like normal again. When I get home in about 8 hours I will try to post Dropbox links to the stock image and the instructions I used.
Click to expand...
Click to collapse
For the sake of closure/followup, and in case anyone has as simple a problem as I had, my case was solved by ... ummmm ... turning the radio back on. I didn't know about the testing page you could get to by dialing *#*#4636#*#* ... I still have no idea how my radio got switched off, but I'm working fine now, thanks to @alray who replied to my question in THIS THREAD
The way I resolved the issue
Sorry I was unable to post the reply at a timely manner.
But I followed the directions at this site http://www.droidviews.com/restore-moto-g-to-stock-and-downgrade-firmware/
and used the US_retail_XT1034_14.10.0Q3.X-84-16_CFC.xml files to reflash back to stock android 4.3
I've been looking and looking and was just wondering if anyone has come across a hotspot mod or hack for the Spring S6 varient.
This service is like a must have for me, and I'd bet a few others could use and benefite from this ( if it has been released, or even in the work in progress)
Look in the note 4 forum - there's a guide there that works and is super easy.
austontatious said:
Look in the note 4 forum - there's a guide there that works and is super easy.
Click to expand...
Click to collapse
The guide in the Note 4 forum worked for me. First, I used the CF Auto Root method to root my phone. Next, I downloaded and installed the latest idoneapps' Galaxy Tools apk (GTv3.1.5.apk.) I first tried the simple method that worked on my GS5 - just click the "Enable Native Hotspot" button and reboot. Unfortunately, that seemed to break my 4G data - I think it has something to do with the APNs being locked. I went back to the GT application and (after reading through the instruction manual) changed the text in the sales_code box from SPR to XAS and hit the "set" button. I rebooted again and now my 4G was working. As a side benefit, APNs are now unlocked. Went back to the GT app and clicked the Enable Native Hotspot button and rebooted. Native hotspot is working fine for me on 3G and 4G. So, if you're having issues, check out that sales_code box.
scubafun said:
The guide in the Note 4 forum worked for me. First, I used the CF Auto Root method to root my phone. Next, I downloaded and installed the latest idoneapps' Galaxy Tools apk (GTv3.1.5.apk.) I first tried the simple method that worked on my GS5 - just click the "Enable Native Hotspot" button and reboot. Unfortunately, that seemed to break my 4G data - I think it has something to do with the APNs being locked. I went back to the GT application and (after reading through the instruction manual) changed the text in the sales_code box from SPR to XAS and hit the "set" button. I rebooted again and now my 4G was working. As a side benefit, APNs are now unlocked. Went back to the GT app and clicked the Enable Native Hotspot button and rebooted. Native hotspot is working fine for me on 3G and 4G. So, if you're having issues, check out that sales_code box.
Click to expand...
Click to collapse
Thanks for this information I'll make sure to try out and I will report back, but can you help me out with the sales quote box how to get to that correctly. And any tips on apraching the cf auto root for the sprint variant
IllMindedSkama said:
Thanks for this information I'll make sure to try out and I will report back, but can you help me out with the sales quote box how to get to that correctly. And any tips on apraching the cf auto root for the sprint variant
Click to expand...
Click to collapse
Instructions for root - and all necessary files - are in the thread here, but there really isn't much to it - install the drivers, run Odin, select the md5 file, put phone in download mode, connect phone to computer, click Start, wait a few seconds for it to finish, disconnect phone from computer, reboot. Less than 5 minutes. The thread also has the link for the stock recovery that is installed the same way and is supposed to improve battery life. I didn't have a problem with battery, but I installed it anyways. You can read the thread for more information and detailed instructions.
For the hot spot, refer to the Galaxy Tools thread on the note forum here.
The sales_code box is the second box on the right. Just tap it as you would any text box you want to type in. The keyboard comes up, delete the text that is there (SPR) and enter XAS. Click the Set button next to it. Reboot. I'll attach a screen shot so you can see what the app looks like once the change has been made.
scubafun said:
The guide in the Note 4 forum worked for me. First, I used the CF Auto Root method to root my phone. Next, I downloaded and installed the latest idoneapps' Galaxy Tools apk (GTv3.1.5.apk.) I first tried the simple method that worked on my GS5 - just click the "Enable Native Hotspot" button and reboot. Unfortunately, that seemed to break my 4G data - I think it has something to do with the APNs being locked. I went back to the GT application and (after reading through the instruction manual) changed the text in the sales_code box from SPR to XAS and hit the "set" button. I rebooted again and now my 4G was working. As a side benefit, APNs are now unlocked. Went back to the GT app and clicked the Enable Native Hotspot button and rebooted. Native hotspot is working fine for me on 3G and 4G. So, if you're having issues, check out that sales_code box.
Click to expand...
Click to collapse
I posted a link to that in another thread here and have been using it since day one. Don't change any settings and just enable hotspot that's it. Have you done any updates? I haven't so I'm still on the original software which may be why but I didn't change any other settings which could be your problem.
cruckus said:
I posted a link to that in another thread here and have been using it since day one. Don't change any settings and just enable hotspot that's it. Have you done any updates? I haven't so I'm still on the original software which may be why but I didn't change any other settings which could be your problem.
Click to expand...
Click to collapse
My phone performed a software update within minutes of me first setting it up - it booted in to recovery and everything. I hadn't installed the root package or Galaxy Tools app yet, so can't say if the update is why I couldn't enable the hot spot with a single click. It would have been the easiest way to go, so I'd suggest that anyone give that method a try first. If it doesn't work, then just make sales_code change and try again.
both of yall,
scubafun said:
My phone performed a software update within minutes of me first setting it up - it booted in to recovery and everything. I hadn't installed the root package or Galaxy Tools app yet, so can't say if the update is why I couldn't enable the hot spot with a single click. It would have been the easiest way to go, so I'd suggest that anyone give that method a try first. If it doesn't work, then just make sales_code change and try again.
Click to expand...
Click to collapse
This method ended up working out for me.
Im a sprint varient fully rooted with the 920t software, and having no issues with the deep sleep battery drain. But i thing i started to notice even with and without the sales_code change is that with some apps (i.e. snapchat). I cant send nor log in to unless i perfrom a info reset code (##72786#) but while doing this. It relocks the apns and disables the hotspot mod.
Any help with this is greatfully apreciated you guys. And also. Thanks again!!!
thanks again
scubafun said:
Instructions for root - and all necessary files - are in the thread here, but there really isn't much to it - install the drivers, run Odin, select the md5 file, put phone in download mode, connect phone to computer, click Start, wait a few seconds for it to finish, disconnect phone from computer, reboot. Less than 5 minutes. The thread also has the link for the stock recovery that is installed the same way and is supposed to improve battery life. I didn't have a problem with battery, but I installed it anyways. You can read the thread for more information and detailed instructions.
For the hot spot, refer to the Galaxy Tools thread on the note forum here.
The sales_code box is the second box on the right. Just tap it as you would any text box you want to type in. The keyboard comes up, delete the text that is there (SPR) and enter XAS. Click the Set button next to it. Reboot. I'll attach a screen shot so you can see what the app looks like once the change has been made.
Click to expand...
Click to collapse
Thanks this worked like a charm but with my last post above. I discovered a little bug.
IllMindedSkama said:
This method ended up working out for me.
Im a sprint varient fully rooted with the 920t software, and having no issues with the deep sleep battery drain. But i thing i started to notice even with and without the sales_code change is that with some apps (i.e. snapchat). I cant send nor log in to unless i perfrom a info reset code (##72786#) but while doing this. It relocks the apns and disables the hotspot mod.
Any help with this is greatfully apreciated you guys. And also. Thanks again!!!
Click to expand...
Click to collapse
Wish I had something useful to contribute, but I'm not having any issues - Snapchat is working fine. Attached is my current software version - as I mentioned, it did force an update the first time it booted up. Maybe pick an app you're having issues with, clear its cache, uninstall and then reinstall it to see if the problem persists.
sorry for the late reply
But i did get to figure it out. The problem was the "sales_code"
I just ad to leave it stock and just let the phone read everything correcrly.
Guys thanks again. Honestly
And also.... have any of ya had the screen rotation problrm???
IllMindedSkama said:
But i did get to figure it out. The problem was the "sales_code"
I just ad to leave it stock and just let the phone read everything correcrly.
Guys thanks again. Honestly
And also.... have any of ya had the screen rotation problrm???
Click to expand...
Click to collapse
I have that rotation issue. It's the damn adaptive charger. The wireless charger never has that issue. It was fixed in a later update supposedly but I had to get my original phone replaced.
anyone have link for GTv3.1.5.apk ?
((Development halted until further notice.)) So I'm not sure if you'll run into any issues, but this is what I'm running
aamszia said:
anyone have link for GTv3.1.5.apk ?
Click to expand...
Click to collapse
I have a Sprint Galaxy S6 5.02 (G920PVPU1AOCF ) rooted with pingpong.
I used GTv3.1.5 then updated to 3.1.8, just enabled native hotspot and nothing else.
Working with no problem.
No root necessary...all you need is your MSL. Easiest way to obtain MSL is by calling Sprint. Once obtained, in the dialer enter ##3282#, hit edit, enter MSL, hit APN Settings. On APN2 EHRPD internet tap on the settings. On APN type it shows default,mms. Edit so that it shows default,mms,dun and then hit ok, up top hit More and hit save. Hit back and tap on APN2 LTE internet settings wheel and do the same...APN type should be default,mms,dun. On More hit save then reboot the phone.
That's it...turn on native hotspot and it should work!
Hope this helps!!
-Apollo- said:
No root necessary...all you need is your MSL. Easiest way to obtain MSL is by calling Sprint. Once obtained, in the dialer enter ##3282#, hit edit, enter MSL, hit APN Settings. On APN2 EHRPD internet tap on the settings. On APN type it shows default,mms. Edit so that it shows default,mms,dun and then hit ok, up top hit More and hit save. Hit back and tap on APN2 LTE internet settings wheel and do the same...APN type should be default,mms,dun. On More hit save then reboot the phone.
That's it...turn on native hotspot and it should work!
Hope this helps!!
Click to expand...
Click to collapse
I tried calling Sprint and told them the GPS wasn't working and they refused to give me the msl but I've been using GT and ended up getting the msl with that
Any app out to get the msl with no roo
Sent From My EDGE
SG Note 3 Android 5.0 Rooted - Worked Great!
scubafun said:
Instructions for root - and all necessary files - are in the thread here, but there really isn't much to it - install the drivers, run Odin, select the md5 file, put phone in download mode, connect phone to computer, click Start, wait a few seconds for it to finish, disconnect phone from computer, reboot. Less than 5 minutes. The thread also has the link for the stock recovery that is installed the same way and is supposed to improve battery life. I didn't have a problem with battery, but I installed it anyways. You can read the thread for more information and detailed instructions.
For the hot spot, refer to the Galaxy Tools thread on the note forum here.
The sales_code box is the second box on the right. Just tap it as you would any text box you want to type in. The keyboard comes up, delete the text that is there (SPR) and enter XAS. Click the Set button next to it. Reboot. I'll attach a screen shot so you can see what the app looks like once the change has been made.
Click to expand...
Click to collapse
Thanks for the help on changing the Sales_code Text from SPR to XAS. It worked well for me after the reboot. I have I've spent almost 5 hours of my morning trying to find out my MSL with countless readers that didn't work. This method you describe did the trick. :good:
Doesn't work on my sprint s6. Sprint gave me the msl code but there is no APN option under the EDIT menu. I can only see APN under VIEW and it's greyed out, cannot be changed