Hello all,
I have just got a new HTC Dream and proceeded to do the following :
I started by flashing dreaimg.nbh drc 7, then a rooted using telnet following the instructions on cyanogen wiki. I then flashed the new radio 26i and the death spl. I have installed cyan 5.0.7t2 plus google apps.
Now however when I boot it up it is staying on the g1 boot up screen and not continuing. Earlier versions of cyanogen mod work but not 5.0.7 for some reason.
Any ideas?
i just had the same prob. im on moto droid. comming from droidmod 1.0 after reboot after flashin newest cgnmod it jut hangs on moto logo. went back to last backup
Cyan doesn't support the droid does it? :S
Mraellis said:
Hello all,
I have just got a new HTC Dream and proceeded to do the following :
I started by flashing dreaimg.nbh drc 7, then a rooted using telnet following the instructions on cyanogen wiki. I then flashed the new radio 26i and the death spl. I have installed cyan 5.0.7t2 plus google apps.
Now however when I boot it up it is staying on the g1 boot up screen and not continuing. Earlier versions of cyanogen mod work but not 5.0.7 for some reason.
Any ideas?
Click to expand...
Click to collapse
Make sure the death spl was installed and make sure to wipe before installing. Install cyan and then gapps without rebooting in between.
I usually have to install gapps after cyanogen. Some people before, some people after. It's kinda odd.
Also, for the droid, there is a cyanogenmod. Dunno if CM5 is on there yet, though. Don't really know anything about the Droid.
I read somewhere that there was a bug in 5.0.7 where you can't use the terminal method to install it, you have to use amon-ra recovery instead (I can't find the page anymore)
I think CM 5.0.8 fixes this
Related
Hi!
I have JF 1.42 RC 33 with root enabled on my G1 from polish network Era.
Then I've decided to switch to JF 1.5 ADP, so first I've installed radio update from htc web page and after this i 've installed 1.5. After succesfull instalation my phone restarts after few minutes and loops on android logo. It is immposible to switch it off. I can only take off battery. Only way to use it once again is to go to recovery mode, then wipe it, and install JF 1.5 one more time. But after this my phone once again is working till first reboot. I've tryied JF 1.5, the Dudes and Hayakuro updatesl but it is same situation. Reboot and loop on android logo.
Now I have JF 1.43 RC9 and new radio 2.22. I've also tryied to install one more time radio update and JF 1.5 update, but it doesn't help. What elsa I can do?
Also I have newest version on Hard SPL. But I did't changed it since I've rooted phone.
szymarek said:
Hi!
I have JF 1.42 RC 33 with root enabled on my G1 from polish network Era.
Then I've decided to switch to JF 1.5 ADP, so first I've installed radio update from htc web page and after this i 've installed 1.5. After succesfull instalation my phone restarts after few minutes and loops on android logo. It is immposible to switch it off. I can only take off battery. Only way to use it once again is to go to recovery mode, then wipe it, and install JF 1.5 one more time. But after this my phone once again is working till first reboot. I've tryied JF 1.5, the Dudes and Hayakuro updatesl but it is same situation. Reboot and loop on android logo.
Now I have JF 1.43 RC9 and new radio 2.22. I've also tryied to install one more time radio update and JF 1.5 update, but it doesn't help. What elsa I can do?
Also I have newest version on Hard SPL. But I did't changed it since I've rooted phone.
Click to expand...
Click to collapse
There are actually a few threads for people running into issues including myself. Mine turned out to be an issue form apps2sd that I have in my thread
http://forum.xda-developers.com/showthread.php?t=511709
There is also http://forum.xda-developers.com/showthread.php?p=3731933
and http://forum.xda-developers.com/showthread.php?t=511955
I have a G1 that I tried to root and mod. Using the the downgrade method to RC29. I've been reading and waiting untill I felt comfortable trying to mod it. When the one click method came out I ordered my 8gb class 6 sd card. By the time it came, the hole was patched. So got rc29 and Cy recovery1.4 did the telnet and got root. When I went to recovery it was Android Recovery not Cy. Even though I had Nandroid b/u 2.2 and it said Zen's recovery build. I did this 3 times with same results. Next I went to drizzy hero full rom. It said to update radio and spl using a link on the page. The link took me to haykuro's radio and hard slp. Installed the radio first (using the update.zip) then the spl. The radio worked, the spl has me stuck on the G1 screen. I've tried everything that I can think of.
Now I slipped my sim into a my touch 2 pro. Is it me or is this what Ive been tring to get all along. This phone is SWEET!! Plus I've been seeing more upgrades and stuff for WM than Android lately. I'm no dev, obvioulsy my G1 is prob. bricked, but it sure seems like you can do almost anything with WM that you can with Android. Except change O/S. My mind is open on any opinions or ideas. (still like to fix G1) (mt2p is still on 6.1, should I upgrade?)
so i have a mytouch 3g with the perfected SPL (i believe ... says HBOOT-1.33.0006 when I check the version with back+power) and I've been using AmonRa's 1.6.2 rom for quite some time now.
I have been looking to upgrade to the Eclair roms floating around the forums which states that it requires a newer SPL so I downloaded the Engineering SPL 1.33.2010 along with the new rom
My question is (after some research) can i just boot into recovery mode and flash the new SPL that way? or is the only way the goldcard way?
You can just flash from the recovery images, but make sure the spl is completed and then he upgrade let me know how it goes
thanks, i'll give it a go and hope it doesn't brick
OK so i got the ENG SPL to install with no problems, but I can't get the rom to install
i'm trying to use Eugene's v2.3 rom found here http://alldroid.org/viewtopic.php?f=130&t=515
it flashes, says install complete, but upon reboot, it loads the mytouch splash page, then about a minute or 2 later, it loads this strange screen with colors that form an X in the middle of the screen and keeps doing that ... i've never seen that before so I flashed back to the 1.6.2 ion rom i used prior
anyone have any ideas?
thats the boot screen...the first time i got it I had to wait 45min for it to finish loading the rom....restarts (after first boot) are quicker....just be patient...I suggest flashing + rebooting then going to sleep...wake up in the morn...if its still going then u have a prob.
This is the screen ur getting right?
http://www.youtube.com/watch?v=lAFSEsEZnnE&feature=player_embedded
yeah, tahts the screen...scared the crap out of me...doesn't make any sense to use an "X" as the boot screen as "X"s are a negative symbol ... i did wait it out, however, took about 5 minutes, but it worked!
I am now running on the 1.33.2010 ENG SPL with eugene's 2.1 rom and it is quite flawless (minus the fact that there's no camera). Hope the camera fix comes out soon!
I'm new to rooting, and new to flashing roms, i downloaded rom manager but it wasn't letting me flash Cyanogen 6.0, So i go to the cyanogen website and follow their instructions to flash CM6 on to my HTC Evo.
It worked, but I disliked the rom and wanted to go back to Baked Snack, so I load up rom manager and tell it to restore to the backup I did before flashing and it won't. it starts to, and aborts, or it half flashes it and i've got this /really/ ugly pesudo htc sense with no apps that takes 20 minutes to load and the market crashes as soon as you open it.
i've flashed back to Cyanogen for the time being cause I want to have a working phone, but I want to get away from Cyanogen, I like HTC sense, and i liked Baked snack.
can anyone help me? I think the problem is the Hboot from when i did the engineering spl step of Cyanogens evo walkthrough..
hi all,
Ok, I'm new to this stuff.
1. used the simple root and it worked great.
2. I then flashed CM7 and it worked great except market was not on it.
3. I downloaded and flashed gapps-hdpi-20101114-signed.zip by mistake, not realizing I had to use another gapps.
4. After I flashed it, the cm7 and android setup screens kept cycling between each other.
5. I restored to clockworkmod (sp) and then deleted the gapps and tried to then flash cm7. It didn't cycle between cm7 and android setup, but the cm7 screens kept cycling and never got past that.
6. I thought perhaps it was just cm7 now, so I tried miui and it's doing the same thing. It's cycling between the gingerbread man and MIUI with the status bar and won't do anything else.
Very frustrated. what have I done and how do I fix it?
Thanks folks,
Brett
You could flash the stock ruu and start over.. or, wipe everything flash cm7 and then flash gapps.
Sent from my Desire HD using XDA Premium App
bdws1975 said:
hi all,
Ok, I'm new to this stuff.
1. used the simple root and it worked great.
2. I then flashed CM7 and it worked great except market was not on it.
3. I downloaded and flashed gapps-hdpi-20101114-signed.zip by mistake, not realizing I had to use another gapps.
4. After I flashed it, the cm7 and android setup screens kept cycling between each other.
5. I restored to clockworkmod (sp) and then deleted the gapps and tried to then flash cm7. It didn't cycle between cm7 and android setup, but the cm7 screens kept cycling and never got past that.
6. I thought perhaps it was just cm7 now, so I tried miui and it's doing the same thing. It's cycling between the gingerbread man and MIUI with the status bar and won't do anything else.
Very frustrated. what have I done and how do I fix it?
Thanks folks,
Brett
Click to expand...
Click to collapse
Follow the instructions here step by step and it will have you up and running in MIUI:
http://forum.xda-developers.com/showpost.php?p=11643155&postcount=1
Read forum rules about where to post. Closed.