I have an HTC diamond CDMA and when I am at certain areas at work I won't get a signal and my battery will drain very quickly. Is there a way to change the interval that the phone will attempt to find a cell tower to 10 minutes or something instead of having it constantly drain searching for a connection?
Related
A work colleague is using a sim free touch cruise on the vodafone network but vodafone don't have any support for this device (mind you neither does HTC ). We got the vodafone settings for billpay vodafone off the internet and input them and can now surf, download gmail etc over HSDPA (H icon shows) and then it automatically reverts to 3G when not in use.
The problem is that the icon for 3G/umts in use is always on (ie the small 3G over the signal strength) and when the bigger 3G icon is touched it shows how long connected to 3G and as the device is still connected it keeps counting time even though the application using 3G is shut down.
My questions are as follows:
In this state (big 3G icon showing and small 3G icon above signal strenght) is this costing anything being constantly connected to 3G but not using it?
How can it be set to automatically disconnect?
My own touch cruise is on the 3 network but I don't have this difficulty.
My thinking is that it might have something to do with "vodafone live" but not sure what is happening or possibly have selected the wrong set of settings for vodafone ireland as there is a few different sets.
Sorry this is a bit long winded but any advice much appreciated.
The always ON connection is general behaviour... it doesn't matter which network is the device on.
The big 3G/H icons only represent the available network (G(PRS)/E(DGE)/3G/H(SDPA))
The smaller is the signal strength...
The cost of the always ON connection depends on the dataplan being used... if it's an unlimited or a fairly large one like 5GB, it won't matter... but it realy depends on the data recieved....
In my case the avarage hourly traffic is around 1 MB, but i have a little e-mail traffic going so... whith a few mails and every 30 minute checking the traffic should be around 500 KB or lower...
As for the Auto-Disconnect, please search the forum... there are several threads about this in both subforums.
Thats great gnick666 thanks for your reply.
I know the Advanced Configuration Tool has an auto disconnect feature, but I had some issues with it and never went back to go play around with it.
You can also hold down the End button and a menu pops up and you can end data connection there. Or alternatively you can configure it so that holding down the End button always disconnects your data connection.
I have an unlimited data plan so not worried about data, I'm not sure however what the impact to battery usage is so I disconnect "just in case".
As for the 3G / H icon behaviors. Depending on which part of the country I'm in, I get different icons. Sometimes I get 3G and it switches to H when doing data. Othertimes it's always H whether disconnected or connected. (This is assuming that I'm in a 3G location) and not switching back to Edge.
Mine mostly shows the bigger 3G icon and the signal strenght icon with the little antenna icon (I'm on the 3 network which is 3g) but when I download data the small icon changes to 3G and then both change to H as required. Once finished it disconnects and reverts back to 3G. I have Schapps Advanced config tool installed.
Hello all,
can anyone tell me how to automatically switch off GPRS (or any connection) after an automated send/receive?
The reason I'm asking is that I set my interval to check for emails every 15m, but after the first time it connects, the GPRS just stays on and this kills my battery!
I would just like to know if there's a way for manilla to switch off any connections automatically after downloading emails.
Many many thanks,
iCE
Just go to connectivity option in menu and find GPRS connection...Then choose turn off option.
OP is looking for an automatic way of achieving this.
I have found that my battery life is dependent on signal strength, a good GRPS connection, over a day, poor GPRS and it struggles. HSPDA and just under the day depending on useage.
deedee said:
OP is looking for an automatic way of achieving this.
I have found that my battery life is dependent on signal strength, a good GRPS connection, over a day, poor GPRS and it struggles. HSPDA and just under the day depending on useage.
Click to expand...
Click to collapse
You alright bloke?
...
Just set the disconnect time, after it stalls of 2:00, have it disconnect.
Paul_Days said:
Just set the disconnect time, after it stalls of 2:00, have it disconnect.
Click to expand...
Click to collapse
Thanks for that Paul,
But how do you do that?
i have htc touch diamond 2 (topaz)
When phone activated (registered to the GSM network) screen in 10-20 sec activates itself and drains my battery.
when phone disabled from the connection menu problem gone and therefore I think it is due to radio rоm
Предложете по-добър превод
Also periodically loses connection for a few seconds to the network.
These problems have emerged since the update towin mobile6.5 with radio rom 4.49.25.17
Is it possible to obtain because radio rom?
With the old Win 6.1 with Radio 3.43, the problem with the activation of the screen was gone, but more often there does happen to lose network.
Network signal is maximum, therefore
Network signal is at maximum, so why is that sometimes gets lost network?
Hey guys,
As the radio stack is the second cause of battery draining after the display, I was thinking about a way to save battery life by reducing the impact of the 3G connection. Most of the energy saving apps on the market are only disconnecting the phone from the APN, but this isn't a great solution as each app could be set to update at different times and thus being unable to download data even if the user sets some exceptions. So I thought that an application which operates in the following way could be great to save power:
- The phone uses the 3G network while the screen is on;
- It switches to 2G when phone is in standby mode;
- It disconnects the APN data connection while the phone is using a WiFi Network;
Obviously to avoid possible issues during the switch between 2G and 3G the following rules are applied:
- If there's an incoming call or a phone call is being performed, there won't be any radio switch until the phone call is ended;
- If there's an incoming SMS/MMS, there won't be any radio switch until the text message is fully received.
Unfortunately as I'm not a Java developer I can't code anything like this. But let me know what you guys think about my idea and if it's technically feasible... Maybe some developer could be interested into further exploring my thoughts and will try to create such an app
Cheers
I'm not a developer but I think it sounds like a great idea. I go into settings and switch it to 2g when I'm in spotty areas outside of town. I have to work a bit to keep my N1 battery alive all day...
Hello I'm new here.
I don't know if your suggested profiles are the best case scenarios. You would need to calculate your data throughput, not just the radio power.
If you need to send 100 packets, your radio would be on the longest for edge > 3g > wifi. So, even though wifi uses the most power, it would be for a much shorter duration.
A profile for "place calls only" would work somewhat like airplane mode, but still keep track of towers. Your phone just wouldn't register on the network unless you wanted to place a call. You would miss your incoming calls, have no data connection, or sms. But, you could have it check at an interval for voicemail or sms. This would be most useful for "ringer off" situations like class or meeting.
Afaik Android is always connected to the APN even if the phone is not downloading anything, consuming a lot of battery power. On other platforms, i.e. Windows Mobile, the connection can be terminated by user and re-established when an app needs that.
The amount of data downloaded by widgets, Google mobile applications or apps which operates in background like eBuddy or Facebook should be quite low, so downloading the required data by using GSM or WCDMA while the phone is in standby would be pretty much the same. The only difference is that downloading stuff using GSM/EDGE should take much less energy power.
So that's why I thought about the app I described before: the phone can save a lot of energy power while in standby and be back to its full horsepower when there is any kind of user intervention. Pretty much the same thing that the system already does for CPU usage. It scales to the less consuming protocol (or, in the case of CPU, frequency and voltage) to save power
I know on the google api it isn't possible to do this, but I don't think that isn't the problem.
At the moment you have 3 options. GSM only, WCDMA only and GSM/WCDMA. Whenever you switch between the 3 of them, the phone will lose signal for 10 seconds before it can find the best network. So the switcher here is not the best as you will lose connection, and what if you are downloading something at the same time...
What you need is when the phone is on GSM/WCDMA that it knows the best network to pick from depending on the phones lifecycle. GSM/WCDMA loses battery power because it always tries to find the best network to connect to, so for example if you are on GSM it will constantly try to find a 3G network etc (as far as I understand it).
What we need is the ability for the phone to stay on GSM when the phone is idle and then when the phone is woken up to automatically start to search for a WCDMA network and then gracefully switch over like it does now. For this I have no idea if it is possible as I don't know how the scanning of the network works. If it is possible then that would be wicked. But this is what we need.
my preference would be if the phone would stay on 3g as long as any possible even if there would be a more reliable 2g connection and only switch to 2g if there really is no way to connect to 3g. turn of apn if the screen us turned of for longer then 1 or 2 minutes and only check every 15 minutes or so.
most of the time I'm on 3g only mode . since I live in a city I got good coverage almost all over the city. only problem is that when there is no 3g available also my phone is unreachable. I don't really miss data connectivity when there is no 3g since 2g is so slow that I rather have no internet at all but not being sale to be called or texted is a major disadvantage...
Sent from my Nexus One using XDA App
Hi all
I am having some weird problem with Google Map
when i use data plan provided by Maxis (my telco) the location that it shows is a few kilometers away from my actual position.
when i turn off the data usage and use my Wifi to open the google maps, it shows that i am off by 40m from my actual position
anyone got any idea what is causing the problem?
Sounds like your telco's not very good at finding your precise location.
I think wifi would always be more accurate. Wifi hotspots don't have much range, and there are a lot more of them than cell towers, so it's easier to know that you're within 40m of Starbucks WiFi #3828 than a particular cell tower.
In my home, with WiFi off and GPS off, the cell towers here usually report me a few blocks away from my house. With WiFi on, it puts me in my own backyard. With GPS on, it puts me in the correct room of the house.