Fun with String Dialing… (and requet for VC bluetooth hack) - Touch Pro2 CDMA

Here’s a new one; most of use string dialing to access voice mail—for example, on Verizon I have a speed dial that dials (where the “$” represents my pin numbers here for example’s sake):
“*86pp$$$$#” No sweat, it dials in gets the greeting, interrupts the greeting and enters my pin.
BUT my corporate voice mail system requires a ten digit access number followed by an 8 digit pin dialed DURING the first ring before greeting pickup. Meaning if I did the same thing:
“$$$-$$$-$$$$,$$$$$$$$#” it was too late—the ring tone was over.
So—is there a way to dial the second string (the 8digit pin immediately without the device thinking its an international call? If I put in 18 digits it ignores the last 8. If I use a “,” or “p” it’s too late.
Is there a way to customize the duration of a “,” (500 ms) or a “p” (1 second) in the registry or a hack for it?
I’m sure I’m not the only one with this problem.
Additional note: since the original post I switched the phone settings to short tone dialing and that worked… for now—but editing the pause duration would still be cool. Ideas?)
Now—if anyone can get Voice command to work with my Bluetooth headset (Jawbone II) I will buy you lunch!! Hell, Dinner!!

Related

Using 2 phone lines on WM5

Hello Guys!
I have two phone numbers which I can use on one SIM.
My provider sends phone calls on line 1 for the fist number, on line 2 for the second number.
On some old (and even new) Nokia-Phones it was possible to see "1" or "2" in the upper right corner on an incoming phone call, and to choose the line for an outgoing call by tap-and-hold "#".
I haven't seen this functionality in WM5 - is there a possibility to tweak that in registry or is there an Phone-Application with this feature?
Thanks for any Idea, Greetings,

Dialing "p" for wait

Hi,
in the old (and current I believe as well) Nokia phone - and most other pure mobile phones for that matter - you can dial a "p", typically by holding down the "*" for a while. The "p" makes the phone wait a little while before continuing to dial the rest of the number.
I need this feature!!!
I am using some prepaid phone cards for which this feature is really necessary.
So, anyone have a clue how to get a similar functionality on WM5? The "p" certainly does not work ...
Thanks in advance - Andy
if you're dialing live, you can dial only the connection number then open the keypad to dial the rest of the keycode manually. If you want to automate it, create a contact with the full number and you can enter in "p" there.
I have a contact for my voicemail which dials the voicemail and waits and the pin + #. this works great with voicecommand cause all I have to do is say "call voicemail" and it'll dial, enter in the password automatically and I don't have to touch the phone at all...
Interesting ... I did migrate all my number from my previous phone, where i had the "p" included in the number. The numbers also seemingly came up correctly on the PPC phone. However, when I tried to dial the number, it would not take the complete number with the "p" - I cannot remember exactly what it did, but it did not dial the whole thing. Thats why I thought/ hoped that there is another way. I guess, after what you are saying, I should give it another try ...
And yes, the application that you are describing is very similar to what I want to use. There is a prepaid international call provider, which has a local dial-in number and lets me call abroad for very little money. I call the local number - the service provider recognizes my account by the incoming phone number of my mobile - and then I dial the destination number. For the recognising part however, it is needed that the phone waits a little before it continues to dial the destination number.
Alright, alright .... works! Thx for the assurance! Tried it again and it just takes a lot longer - the pause is longer - than it used to be on my Nokia. Also, I do not hear the dialing tones after the "p" anymore, which probably put me off before.
Thanks! Thread closed
Try replacing the "p" with a "," . It will pause for a few seconds once the other side picks up the phone.

How to automatically dial calling card for long distance numbers

After too much time spent hunting around I've found a reliable way to force all long distance calls to go through a calling card. I've tried Long Distance Dialer and Sunnysoft Calling Card with poor results and suffered with shoddy interfaces. With this method you can use whatever dialer you like.
I'm using this in Canada where we do NOT have national calling--so depending on your plan, your mileage may vary with my specific rules.
I'm using the program MagiCall by Mobiion Software.
Here's what my rules are:
1. Create a rule to bypass future rules for local calls. In the action menu choose "Normal" and "Do nothing".
We have 2 area codes that are "local" most of the time.
The * at the beginning allows prefixes like "1" or "+1" (they are detected differently).
The * at the end is just to make sure it allows automatic dialing of extensions, etc. Note that any numbers with a , and additional digits at the end DO NOT work through the calling card rule properly.
Technically a number like 011 (60) 4123-1234 could slip through, but highly unlikely if not impossible.
*604-???-????*
*778-???-????*
2. I create a separate rule for toll free as sometimes I'm outside of the 604 area code and all calls there will be long distance. When I leave 604 I disable the rule to bypass local calls. In BC we also have 310-???? numbers that are toll free.
*800-???-????*
*866-???-????*
*877-???-????*
*888-???-????*
#*
\**
The last 2 are for #CODE's, and "\**" is for things like *611. Note that you can't properly enter a \ with the symbol panel on the TyTN. Use a different SIP like Fitaly, or enter a few extra rules: "???, ????, ?????" to cover your bases.
3. Create a rule for your calling card.
Filter type: All
Operation: Change Number
Call to: 877CALLINGCARD,PIN#,{phone}
It turns out some calling cards don't accept any darn number like my home PBX which automatically reformats calls for the provider.
Here is how I've set it up for my new Pingo calling card which requires a 1 before each 10 digit number and a # at the end. I should warn you that the Pingo calling card does NOT work with my Telco's voicemail. Anything involving DTMF is hit and miss after they've passed on the call. I have 3 calling card rules:
1. 10 digit dialing - This rule will only take the last 10 digits of the number dialed and send them with a 1 at the beginning.
Filter: ???-???-????, 1???-???-????, +1???-???-????
Operation: Change Number
Call to: 888PINGO,12345678901234,1{phone}[0,+10]#
2. International Calling.
Filter: +*
Operation: Change Number
Call to: 888PINGO,12345678901234,011{phone}#
3. Catch All - This just assumes the number is formatted correctly. It's also in hope of catching all numbers to avoid calling LD. If you can think of any other number formats, please let me know.
Filter: All
Operation: Change Number
Call to: 888PINGO,12345678901234,{phone}#
Other tips:
* To enable or disable dialing with a calling card, open the rule and check or uncheck the "Enabled" box on the left.
* When I'm outside of my local calling area, I disable the rule to bypass local numbers. This way calls to back home go through the calling card as well.
* To move rules up and down, click and hold on a rule.
* To automatically enter your voicemail password no matter how it's dialed. (With my TyTN I can't add ,password to my voicemail # in settings).
* Create a rule that automatically adds your prefix in areas where 10 digit dialing is mandatory. Example rule: ???-???? to 604{phone}. Be careful though, because once it's hit a rule, it won't follow through to a calling card one.
* Create a rule that adds your voicemail password to the end of your VM # automatically. This way you can use your fixed speed dial #1 for it.
* If you hate getting SMS's for your voicemail on top of the regular notification. Add a rule to delete them. I use the rules +Voicemail and +Urgent.
* Here on Rogers Wireless we have e-mail to SMS, but unless you pay a monthly fee, you need to reply with "read" to read the message! Set a rule for SMS that matches the phone number +30500* and the filter +"You have mail from" +"please reply with". Action1: Delete, Action2: Send SMS To:{phone} Message:read
* Want to check SMS delivery reports, but not have to delete a popup each time? Set a rule to move all delivery notifications to deleted items, and tick "tray icon" on the Others tab.
Please post your results for others to learn from.
Thank you. Very helpful. I am using the same product.
International calls with MagiCall
Here's what I did. Using my contact manager, MS Outlook, I assigned a category called International to all the contacts that would require for me to use my Calling Card. Then I created a Rule in MagiCall called 'Calling Card', Rule Type 'Phone Outbound', Filter 'Category', Categories 'International', Enabled. Then on 'Operation' tab: Action1 'Change Number', Call to: '13055035800,011{phone}[-1,0]#'
Explanation of Call to:
- 13055035800 is the number for Nexogy (Previously called Solollama), the LD call is cheaper than calling to the toll free number, plus my cell has plenty LD calls prepaid.
- , waits for the Nexogy server to pick up
- 011 is the international calling digit from North America
- {phone} places the Phone Number from the phone book
- [-1,0] strips the '+' sign at the beginning of my numbers. My numbers are formatted as +58-212-123-4567
- # is the end of number command for the Nexogy server, without it'll take an extra 2 or 3 seconds (an eternity!)
Regarding the password. My CC provider doesn't prompt for password when you've preset a your phone number on their website. Otherwise the Call To would look like: '13055035800,1234011{phone}[-1,0]#' being 1234 the password. If your provider needs more time to acknowledge the password, then you can try '13055035800,1234,011{phone}[-1,0]#'
The final number dialed will be: 13055035800(wait)1234(wait)011582121234567#
Hope this helps! If you find a software similar to PalmOS Takephone please let me know.

Any software to make sending DTMF touchtones possible??

Hey guys,
I just started using Treo 750. I love it so far except few things I miss about my old Nokia. Earlier I used to dial a calling card number and then just choose the contact's destination number by selecting "Touch Tone" option from the menu while in call, and it would touch tone that number for me and I was connected. Now, WM5 phone app doesnt seem to be able to do it, and I have to write down the contact's number on a paper first before dialing calling card access number.
Also, I know a comma can be used a 1-second soft pause, but any possible way to add hard pauses in the phone number like traditional cell phones can do... Its cumbersome carrying calling card's PIN code in pocket, and then entering it after dialing calling card number and then punching in destination number from a paper again... its frustrating...
I tried to look up a lot of dialers and apps, but none was a helpful find. Could someone suggest any way out.
anybody???
http://www.google.dk/search?source=...c&btnG=Google-søgning&meta=lr=lang_da|lang_en
I am using a product called MagiCall which has the calling card feature as well as calls filtering and SMS filtering.
I think it can help you.

Google Voice Stopped Working!

So I had my phone set up to where the voicemail forwards to my Google Voice, and had it working the other day. Now when people call they get a message saying that the wireless number you called is not in service.
I've tried a couple tests and here's what i came up with.
1 - Dial my cell phone directly, phone rings 5 or 6 times then gets the wireless subscriber number not found message.
2 - Dial my cell, then slide to reject the call on the cell, get busy signal
3 - Dial my Google Voice number, which then rings my cell, I let the cell ring a few times, then it goes to Google Voicemail like it should.
I have the Captivate set up to use Google Voice as the voicemail provider, and I have my google voice number entered as the voicemail number.
Is there a common setting or issue that I missed, or do I have a real problem on my hands? My phone is rooted, but still efault ROM.
I had something similar happen to me when I switched from my iPhone. I think it has to do with the number of rings before google voice picks up. For some reason they set it to 25 seconds and that's not changeable; however, you can lengthen the number of rings before your voicemail carrier takes over. Try changing it to 30 seconds with the instructions below:
1. On your phone, dial *#61# and click Send.
2. Some information should be displayed: number that the calls are being forwarded to and the delay before the forwarding engages.
3. Write down the number (including +1)
4. Dial **61*+1xxxyyyzzzz*11*30# and hit Send. +1xxxyyyzzzz is your google voice number, 30 is the delay in seconds. The delay can be set in 5 second increments, 30 is maximum.
5. Dial *#61# to verify that the new settings are active.
This worked for me, although you do have to wait a ridiculously long number of rings before it forwards it to GV. Nothing we can do about that until Google lets us mess with their 25 second time limit.
I'm thinking a lot of people will hang up before letting it ring that long. Its sort of like that saying "A watch pot never boils".

Categories

Resources