Not booting anymore - myTouch 3G, Magic Android Development

Hi everyone,
I have a problem with my phone, during a ROM upgrade i received "Failed" on my screen and after reboot I see a white screen with some info about my phone, RRU text and at bottom an image with a chip.
What can I do ?
Thanks!

U need tell us more do u have a 32A or 32B wat rom did u try flashing?

Hello,
I used RUU_Sapphire_HTC_Europe_3.05.401.3_release_signed_NoDriver.
My model is 32A.
Thanks.

hi,
been there done that, here's my step :
Download this file :
http://rapidshare.com/files/310783087/HTC_Magic__SMARTONE-VODAFONE__ROM_3.03.990.6_with_HTC_Sense.exe
it's solve my half brick magic.

Hi,
I tried the update but it's not working. I receive this on the screen :
Checking Custom ID ...
Update Fail!
In the attachment you can see how my screen looks like.
Thanks.

Any ideas on this ?

make sure you phone is fully charged.
it happened to me once it stopped on the half way during installation bcoz of the low battery.
take out the battery, wait for a while, put it back, don't turn on, just charge.
I saw you got a perfect SPL, I think you can try all 3.5 RUU except the one comes with 1.76,0010
if you have a gold card, you can get any rom1.zip from above RUU to try it.
(i think rom1.zip)
don't forget to rename it to sappimg
hope this help.
cheers

Hi thihaz,
Thank you for your message.
How much should I keep the phone on charge ? The battery has a lot of power, it's almost full.
So the SPL from my attached image is good ? Can you recommend me a good ROM ?
I tried a few more ROMs but during the installation that screen persists and I receive the message :
Checking Custom ID ...
Update Fail!
I tried to make a gold card, but the VolumeDown+Power combination doesn't work. Also, I cannot boot into fast boot.
From that screen I suppose that the phones expects some kind of signal from RRU install but I don't know what to say ... I'm not an expert.
Thank you very much.

fatsal said:
hi,
been there done that, here's my step :
Download this file :
http://rapidshare.com/files/310783087/HTC_Magic__SMARTONE-VODAFONE__ROM_3.03.990.6_with_HTC_Sense.exe
it's solve my half brick magic.
Click to expand...
Click to collapse
Can you please explain the steps you follow to fix the phone using the file in the link you provided?
Also your phone is a 32A or 32B?
I might need to try this too but would like to hear some more of how you did yours.
Thanks

On my 32A didn't worked that update.

Isnt 1.76.0009 perfected?
Well something tells me you need to get the RUU which fit your phone. One with the same or higher SPL cause you got S-ON. Good luck with it!

florinmatinca said:
On my 32A didn't worked that update.
Click to expand...
Click to collapse
Does anyone has this file but for the 32A? (1.2 and Fender)

Hi everyone,
With a great help from HTC Support I fixed my phone.
My model is HTC Magic from Vodafone Romania.
To fix it I downloaded a ROM from here : http://www.htc.com/cz/SupportDownload.aspx?p_id=246&cat=2&dl_id=776
Please note that this ROM is designed for models from Vodafone Romania.
Cheers.

Related

Fatal downgrade...

Hi there,
My currently installed Rom was RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1.exe. (thank you jester for you good job)
Nevertheless, this ROM is in English and I wanted to downgrade to a French One before the selling of my device.
I have tried to install the downgrade kit detailed in this topic : http://forum.xda-developers.com/showthread.php?t=267344
The first step went OK but while trying to make the secnd step, my qtek is blocked at the boot splash screen showing the Jesterz picture and red information about the SPL and so on on the upper left corner... without starting... The USB connexion is not detected so I can't do anything... While trying to install any ROM, the USB connection is not detected ang I get an error message...
Did I kill my phone ?
Please help ! Tell me that it's not dead....
Don't worry, its nowhere close to being dead. If you have superCid, then use the SD card image to restore in bootloader mode. However, if the Cid is locked, then you would need a utility that can unlock Cid without Activesync mode (coz in your case, you would not be able to get an Activesync connection). imei-check.co.uk has a utility ($38 i guess) that unlocks Cid in bootloader.--- else show it to a professional. (in my country, I would have to shell out around $20 to get such a problem fixed at a mobile repair shop)
illanz said:
... The USB connexion is not detected so I can't do anything... While trying to install any ROM, the USB connection is not detected ang I get an error message...
Did I kill my phone ?
Please help ! Tell me that it's not dead....
Click to expand...
Click to collapse
Just take out the battery for about 10 minutes and re-insert. If it does not re-start, do a soft resert with the stylus and hopefully you should be fine
Hy,please help!
after downgrade, it doesnt work anymore.... i mean... i cant start the mobile!
after the downgrade i disable the USB data cable and now the mobile is dead... it doesnt starts from the ON/OFF Button and even if i connect the USB cable it makes nothing! No Led on... nothing! absolutly DEAD!!!
I have tried to put off the battery all night long with no result.. but I have achieved to reach the bootloader mode by pressing the camera button while soft reseting and keeping the camera button pushed...
OMG, I have been so scared ! ! !
Try this in order to reach the bootloader:
Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and KEEP PRESSING camara button till appear the Boot Loader.)
it doesnt work
I seem to have a simular problem. this is my post in another topic. It seems to fit better here.
This is what I tired so far:....
I used the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_S hip-NoVendorID and it often hangs and was slow with Push Email over GPRS.
I tried to find a way to downgrade but hadn't had time sofar. When I logged on XDA Developers Site I saw there was a new Image.
So I thought Great I dont need to find how to downgrade.
I don't know what G4 and G3 is so as everybody let's try the higest best one.
I uploaded the RUU-Prophet-G4-AKU3.3-Jester-b1
Wrong...
Now as previously stated I get to the multicolor screen with IPL 2.09 and the SPL 2.20..0001 on the screen and that's it.
I can get to the bootloader and load the same image again and get the same result.
I can load another image on and it loads to 80 Percent and says error [326] Invalid Command This NBF cannot be used with your PDA Phone. Please check your NBF file.
If I try an older Version it tells me upgrad only
And when I try to upload the G3 version it tells me error[300] invalid upgrade tool. This upgrade utility canot be used for your PDA Phone. Please get newer Upgrade utility.
Trying to use the nf.nbf or the G3 with the ROMUpdateUtility_NoID of the G4 doesn't work either.
If I would like to do the downgrade tool I need a Active Sync connection which I don't have.
I have no more thoughts. Please Help.
If you would have just read the forums better you would have known if your device is a G3 or a G4. (read this!).
Now it appears you have tried both for an update. Which may possibly have bricked your phone.
But... first things first. Can you get into the bootloader? (read wiki HERE on how to do that).
If you can still get into the bootloader then there is still a possibility for updating.
Try upgrading with the latest Qtek rom (note: this is an official rom, this one works for both G3 and G4! And since it's the latest you should be able to upgrade to this one).
Instructions quoted from another post of me:
You could try the 2.20 qtek rom which seems to be working well for quite some people (found here).
Although you have to make sure you read that thread good and use the ROMUpdateUtility_NoID.exe (found here ) to upgrade.
Update instructions:
1: With the qtek 2.20 rom you need to extract the zip and the exe file in the zip with WinRAR.
2: Then there is one folder called 'OutputFile' and a folder called 'RUU_TOOLS'.
Inside the RUU_TOOLS there is prophet and in that one WWE, when you go through them and in the WWE folder you see a bunch of files (readme.doc, enterbootloader.exe etc etc).
You need to copy ROMUpdateUtility_NoID.exe to the WWE folder with all the files. And you also need to copy the 'nk.nbf' file to the WWE folder (from the 'OutputFile' folder).
3: And then you need to put your phone in bootloader mode and run ROMUpdateUtility_NoID.exe to upgrade, which should work nicely then.
Click to expand...
Click to collapse
This should give you a good enough idea of what to do. This should work (new rom combined with no NoID updater).
However, if it's impossible to get yourself into the bootloader your options of upgrading your device are getting smaller.
Downgrading of a complete rom is only possible on a CID unlocked G3 (when it's CID unlocked you would know! because you would have done that yourself) and not on a G4 device.
Flasing a G3 device with a G4 rom or G4 device with a G3 rom might possibly turn your phone into a brick. This can easily be avoided by reading the forums properly and know what you are doing.
If anything (even if it's a small thing) is not completely clear to you about upgrading/downgrading your device I'd recommend not doing so.
edit: oh yeah... if you have a G4 device (which you should know by now) you cannot downgrade from this rom (well, only via a payed online service). And when you have a G3 device you could try and CID unlock it (read wiki + forums) before you want to downgrade, or don't downgrade at all.
But whatever you do, don't try to downgrade it without doing any of those things because you'll get into trouble. (to put it down bluntly)
illanz said:
I have tried to put off the battery all night long with no result.. but I have achieved to reach the bootloader mode by pressing the camera button while soft reseting and keeping the camera button pushed...
OMG, I have been so scared ! ! !
Click to expand...
Click to collapse
If you have reached the bootloader screen, just run my installer (or any official ROM) to get your phone working again.
My Prophet Died
I need help, to restore my Prophet, i upgrade wrong rom, i need will try the SD Backup, where can i see this process ?
Sorry my Inglish is too bad.
I've merged a couple of threads under this one, as they are all about the same problem (mostly)
Opening a new thread for the same problem isnt very useful
Hi RaptorRVL
Thank you very much for your patience in resuming all this for me.
I do try to read the forum but it isn't like a manual where you find the procedure stepby step. Like the G3 and G4 version I have newer come across until now. Sorry.
I tried the image you metioned and I have the result that at 80% it tells me error [326] Invalid Command This NBF cannot be used with your PDA Phone. Please check your NBF file
Any more thoughts?
As you seem to be an expert Can you let me know more about goldcard solution.
Cheers
Mick
From a readme I once found inside an update:
* ERROR [320~328] : INVALID COMMAND
These errors seldom occur. However, if one of these errors occur, it could not be recovered and the device had to be sent back to the customer service center. In this case, you have to flash a new ROM code.
Click to expand...
Click to collapse
Doesn't sound too good really. Maybe someone else here on the forums know what to do with this error :/
You did use the ROMUpdateUtility_NoID.exe and not the normal updater right? Can remember someone getting a similar error when using the wrong updater, but I'm not sure about that though...
edit: try doing a search on the prophet forums for "INVALID COMMAND" maybe there is a helpful post in there somewhere...
THANKS!! I was worried b/c i had the same problem today. I've been looking for so many threads abt this problem. Thanks for ur help guys!
same problem
so i have the same problem. I want to downgrade and it break at 95% invalid file. But now XDA is still alive. I can`t go into the bootloader but i tried this file: RUU_Prophet_220734_2207114_024721_NVID.exe
and now my Prophet is still running again. Hope i can help you. Good luck.
peter paul
P.S. sorry for my english, but its good to learn it again

Wont Boot

I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Drunknasty said:
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Click to expand...
Click to collapse
if your device is G3, unlocking is required to flash any rom, before upgrade your device, it is recommended to flash an official WM5.0 rom (in your case T-Mobile rom) with IPL and SPL 2.xx then flash again.
in general there are many probabilities for your issue.
((Where is TNT1.1?? did you mean 1.0?? ))
My Bad meant 1.0
So to get it straight.... I will need to unlock my phone each time?
Oh and to correct myself again, when flashing with the T-mobile ROM it says UPGRADE ONLY. And the read me file says its the wrong RUU. But it is the same file from Tmobile I used when I first got the phone. But I will try again.
Are there any other suggestions?
You need to read the "how to flash" sticky.
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Try another ROM.
Sounds like you need the "Wizard Love" rom. I dont have the link handy but I am sure someone else does.
Drunknasty said:
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Click to expand...
Click to collapse
Already got it. Thanks I am trying to load it now. But the only thing is that the last time it failed and I can understand what the error says. I know the number is 300 but can read the language.
But I will let you guys know when this load completes.
Thanks again for all the assistance.
No worky worky. The load completed and then boots the splash screen shows and then stays there.
Any ideas?
Try to remove the battery and let it out for at least half an hour. Then put it back in and see what it does then.
I thought the same thing too. So when it got done last night, out of frustration, I removed the battery and left it there to wait on when I get off work today. I will report back on what happens.
Again I would like to thank you guys for helping me. I really do appreciate it!
STEP 1 install the original manufacturer ROM
T-mobile UK
http://www.tm-phonedownloads.com/download_manager_mda_vario.html
T-mobile US
http://www.t-mobile.com/wmupgrade/
Search for the original rom for any other
instructions on how to use the original rom can be found here
http://support.t-mobile.com/knowbase/root/public/tm23294.htm?&A2L.SERVICE=AboutUpgrading
Put it in the bootloader mode.. ( three color screens )
hope this helps..
cheers
Praneet
Ok I did that and it gave me ERROR 296: UPGRADE ONLY
Then it tells me that the NBF file cannot be used for my PDA Phone. Please get newer NBF file.
Is there any way I can get the Tmobile splash and IPL\SPL number back to original, it doesnt need to boot all the way into WCE but atleast show the same numbers and splash during boot up?
Or any other way to get this thing to work?
Thanks guys
BTW it is a HTC Wizard from T-mobile.
If you are getting an error 300 you need a newer rom update utility, and regardless if your phone is a G3 or G4 it needs to be unlocked before you flash any rom.. LOAD a OFFICIAL cingular ROM onto your device before going any further, then unlock your phone either via www.imei-check.com or through some of the tools offered here...
Which one should I down load from Cingular? Even though I have a Tmobile phone?
what ipl and spl are you using and what radio are you using. Just post all the numbers from the bootloader
As soon as I get home, I will post them.
Thanks
Ipl 1.01
Spl 3.08
Thanks
Drunknasty said:
Ipl 1.01
Spl 3.08
Thanks
Click to expand...
Click to collapse
uh oh. someone tell me if I'm wrong, but I think this is bad. it's the result of flashing a g4 with g3 or the other way around... keep searching, and good luck.
flash the original t-mobile rom. your phone doesn't appear to be unlocked. good luck

stock on 0% flasahing rom

hello everybody
i started to flash a new rom
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[No_CubeV2]
and i think i followd all the instractions but after starting the flashing it stock on 17% after removing the battery as the program said it wont go over 0%
firs i installed kaiser-HardSPLv1 and after that i started to flash the rom and its not working.
pls tell me what to do to save my nice phone
dannt
speebman said:
hello everybody
i started to flash a new rom
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[No_CubeV2]
and i think i followd all the instractions but after starting the flashing it stock on 17% after removing the battery as the program said it wont go over 0%
firs i installed kaiser-HardSPLv1 and after that i started to flash the rom and its not working.
pls tell me what to do to save my nice phone
dannt
Click to expand...
Click to collapse
"think" you followed all the directions?
sorry for my bad english or leak of knolge in this part of the world i just read so much regarding this subject ant the more i read the more i got confused
so i just sow the first logical faq and followd him, plz i need my phone all my life is in their, help me.
danny
speebman said:
hello everybody
i started to flash a new rom
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06[No_CubeV2]
and i think i followd all the instractions but after starting the flashing it stock on 17% after removing the battery as the program said it wont go over 0%
firs i installed kaiser-HardSPLv1 and after that i started to flash the rom and its not working.
pls tell me what to do to save my nice phone
dannt
Click to expand...
Click to collapse
Things that will help others help you:
1. where are you located?
2. who is your provider
3. what ROM WERE you on?
4. ok - you had a phone that was working - and you did:
a. what did you do first?
b. second?
c. etc.
Your message KINDA indicates that you flashed a ROM and had issues - so you THEN flash HARDSPL? was that successful?
Bill
im from israel but my phone is from uk i think, my original rom was the HTC 6.1
i just run the kaiser-HardSPLv1 program and then i started flashing the rom duty 6.1 rom and it stoped at 17% like the program said i removed the batery and started the flashing prosse again but now it doesny even go above 0%, now im stock in the tri color screan
its writen
kais130
spl-3.28.0000
cpld-8
and usb in the littel whait screan
speebman said:
im from israel but my phone is from uk i think, my original rom was the HTC 6.1
i just run the kaiser-HardSPLv1 program and then i started flashing the rom duty 6.1 rom and it stoped at 17% like the program said i removed the batery and started the flashing prosse again but now it doesny even go above 0%, now im stock in the tri color screan
its writen
kais130
spl-3.28.0000
cpld-8
and usb in the littel whait screan
Click to expand...
Click to collapse
you don't have hardSPL installed..! surprise, surprise
u don't have hardspl flashed from bootloader info u provided. flash hardspl be4 flashing any roms.
please search and read; this has been answered many times.
p.s. use the new hardspl by jocky which is a sticky in this forum.
speebman said:
im from israel but my phone is from uk i think, my original rom was the HTC 6.1
i just run the kaiser-HardSPLv1 program and then i started flashing the rom duty 6.1 rom and it stoped at 17% like the program said i removed the batery and started the flashing prosse again but now it doesny even go above 0%, now im stock in the tri color screan
its writen
kais130
spl-3.28.0000
cpld-8
and usb in the littel whait screan
Click to expand...
Click to collapse
OK - I do not think that you got the HARDSPL installed on your phone correctly - BECAUSE - I believe that it would say OLIPOF or JOCKY on it and it does not.
I have not seen the new HARDSPL 328 and 329 but it LOOKS like to me that you did not successfully get the HARDSPL on your phone.
Personally - I would scan the message boards for GSLEON3 (user name) and send him a private message - there are many others that can help you and he or others MAY come trolling by and take pity on you - but at the moment he is the one that helps people in your situation the most from what I have seen.
I would NOT continue to work on it myself as you can definitely mess your phone up permanently. Does your phone still go into boot loader mode? If so - can you flash the required HARDSPL onto your phone?
Find a message that GSLEON3 has left and then lik on his name and send him a private message - he is very nice - BUT - he is VERY busy - continue to be nice and he will most likely get you back and running.
Bill
first of all thank u for the help
but, wich one i need? 28 or 29?
and how do i do this spl if i cant copy them to my device.
danny
speebman said:
first of all thank u for the help
but, wich one i need? 28 or 29?
and how do i do this spl if i cant copy them to my device.
danny
Click to expand...
Click to collapse
Danny -
Deep cleansing breaths here ok?
1. personally - I would PUT BACK what ever you had on your phone and get it running again - trying at this point to get ot to go to a different ROM is not a good idea right at this minute.
2. 28 and 29 from what I read makes no difference - users try each one to see which one works better on THEIR flashed ROM.
3. What I would do is look for the HARDSPL that goes with what you had loaded to begin with - or the actual SPL that came with your original ROM and put that one back.
I would be stuck here because I have to use JUMPSPL on my phone because I get the white screen - but I THINK that (don't quote me because I do not do it this way) if you don't get the white screen you can just flash the HARDSPL to your phone without JUMPSPL (having to be able to copy something to your phone.
HOWEVER - if you cannot or do not know how to continue from reading the WIKI - you MUST request help from a professional - I have already recommended one. (GSLEON3)
Bill
my active sink is not seeing the devais, maby MTTY? wil help
speebman said:
my active sink is not seeing the devais, maby MTTY? wil help
Click to expand...
Click to collapse
Based on your current track record, I wouldn't suggest you use MTTY as you have a VERY HIGH probability of bricking your phone (ie: it won't ever be usable again).
so im fu--.
Can you get the phone into the bootloader mode? Turn the phone off (pull the battery if you have to) then press and hold the camera button while you turn the phone on. You should get to a tri-color screen (this is the boot loader). Now plug in the USB cord and see if it switches from saying Serial to USB. If so, you can try flashing AN OFFICIAL ROM THAT WAS MEANT FOR YOUR PHONE (ie: Don't try to put an offical AT&T rom on an Orange). When you run the RUU program it will tell you that you need to have ActiveSync working, but don't worry about that. If your phone in bootloader shows USB, you can continue on.
BUT AGAIN... You need the Official rom that was meant for your device. Since you are not HardSPL'd you have to do it this way.
If you don't understand any of that, or have questions, don't just try it hoping you get it right...
As stated previously, it would be well worth you time to get someone like GSLEON to assist if you can.
mfrazzz said:
Can you get the phone into the bootloader mode? Turn the phone off (pull the battery if you have to) then press and hold the camera button while you turn the phone on. You should get to a tri-color screen (this is the boot loader). Now plug in the USB cord and see if it switches from saying Serial to USB. If so, you can try flashing AN OFFICIAL ROM THAT WAS MEANT FOR YOUR PHONE (ie: Don't try to put an offical AT&T rom on an Orange). When you run the RUU program it will tell you that you need to have ActiveSync working, but don't worry about that. If your phone in bootloader shows USB, you can continue on.
BUT AGAIN... You need the Official rom that was meant for your device. Since you are not HardSPL'd you have to do it this way.
If you don't understand any of that, or have questions, don't just try it hoping you get it right...
As stated previously, it would be well worth you time to get someone like GSLEON to assist if you can.
Click to expand...
Click to collapse
thank you!!!!!!1
i have flashed to my priviuas rom the original 6.1 htc rom and now its ok!!!
tnk
speebman said:
thank you!!!!!!1
i have flashed to my priviuas rom the original 6.1 htc rom and now its ok!!!
tnk
Click to expand...
Click to collapse
Cool. Glad that worked for you.... NOW, your next task is to read and understand ALL the steps before you try flashing a custom rom. HardSPL that sucker (but understand and follow EVERY step before you try that) and then you should be good to go...
my only problem is that their are so many strings of information and so many threads even wiki is confusing.
i will try to do this after i will make some order it all of this.
tnx again 4 the help
danny
speebman said:
my only problem is that their are so many strings of information and so many threads even wiki is confusing.
i will try to do this after i will make some order it all of this.
tnx again 4 the help
danny
Click to expand...
Click to collapse
Yes it is, but if you read this sticky at the top, it should help (start with noob guide which is the first link I think):
http://forum.xda-developers.com/showthread.php?t=369282
speebman said:
my only problem is that their are so many strings of information and so many threads even wiki is confusing.
i will try to do this after i will make some order it all of this.
tnx again 4 the help
danny
Click to expand...
Click to collapse
Not to be mean but if you have red Wiki and looked at threads here and they "don't make sense to you". You really have no business flashing a rom. If you don't understand what you are doing sooner or later you will brick your phone from your lack of knowledge and it will be no ones fault but your own.
I am really surprised people were willing to repeat what has been typed out hundreds and hundreds of times on these forums.
Welcome to XDA

Reverting to official RUU with HardSPL

I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum
flipside123 said:
I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum
Click to expand...
Click to collapse
I'm uploading a zip file which will have the entire thing already to go.
Just flash your device as you would with any other rom.
Hang tight the link will be available within 10 mins.
Thank you sir. Greatly appreciated
flipside123 said:
Thank you sir. Greatly appreciated
Click to expand...
Click to collapse
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM
flipside123 said:
One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM
Click to expand...
Click to collapse
Okay,
I thought you wanted to go back to the original T-Mobile rom.
If your trying to HARD-SPL your device to install one of my roms or another cooks roms then thats another story.
Please read my FAQ or one of the stickies.
Ok, I think I got it now. So I don't need to revert to the original ROM to flash it since I have HardSPL? Thanks for the help
wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there
I tried the file that you uploaded here...And it went thru the whole process of flashing the ROM, but after it updated my wing just stays on the T-Mobiel screen and never boots past that.
It had that open touch software on it and I don't want open touch. I want plan old WM 6.0 on there.
I called T-Mobile and got an offical 6.0 update from them, but when I try that one it gets to 1% then says it has a disconneted and I get a connection error.
ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
So does this work? The two people who did this had problems. I need the phone to be all stock so I can have t-mobile send a free replacement because the screen is going on this wing.
***EDIT:*** Oka so this is the same as http://forum.xda-developers.com/showthread.php?t=364543&page=2 the first time I tried it it froze at 15% on step 2 so I installed the RAPI CAB like it says. Step two completed, phone rebooted and had white screen then I got error 260 I think. I have the stock t-mobile rom on it and had it on before I did this but it still has the yang from when I did a hard spl. Is there another way to get it to stock or am I doing something wrong? Plug in phone, let it sync, run herald-uspl.exe hit enter and so forth.
***EDIT*** Ok so this time it completed but is now stuck at the T-Mobile screen and I am now unable to even flash because I can't get past it And that damn yang still shows up in bootloader. Well went into bootloader and flashed from there so phone works but the damn yang is still there. And on a side note: Has anyone ever had a problem with their screen going very dark after flashing a rom from here? Phone was fine then I flashed OTP v7.4 TouchFlo 2D Lite.nbh yesterday and at night screen started going dark, would light up when opened in keyboard mode, then switched and then both were very dark and hard to see. I then flashed to OTP v7.3.1 TouchFlo 2D Final.nbh and still dark. Then I flashed to stock rom and have been able to see the screen since.
This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4
smokeingit said:
This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4
Click to expand...
Click to collapse
Did not work. Do I need to install the cab files again? I know I deleted a file out of the stock rom so it would not overwrite or verify or something but I put that file back, should I not have? This has been a few weeks and still can't get the yang off. Screen on my girls phone is almost dead, she can't even slide it any more so I need to fix the spl so I can send back to t-mobile....anyone ?
this is what i do to get back to the tmobile orginal. download the software from tmobile. I downloaded the newest update from tmobile site. REMOVE YOUR SD CARD. Connected my phone via usb. Launched the update. It has never failed me yet. It is just like updating your phone. tmobile has to take it, it is their update. They sent me a new phone noproblem, matter of fact i have to do it again, the back on the phone keeps getting loose on me. so they are sending me another phone again. hope this helps.
Alternatively you can use the combination of uspl and stock rom ruu to return your device to stock tmobile rom...
1. Enter in to uspl like you were falshing one of ttran001 roms... You can get this HERALD-USPL-beta3 from http://rapidshare.com/files/79249048/Flash_Center.rar
2. ONLY use steps 1 and 2 from the black screen (getting the white screen on your device)...
3. For step 3 in the flasher exit out of the black screen (windows cmd screen) by pressing ctrl+C...
4. Fire up the official ruu from tmobile found here http://forum.xda-developers.com/showthread.php?t=358030 or alternatively if you have a tmobile account still active you can get the most up to date rom from http://www.t-mobile.com/wmupgrade/
5. Fallow on screen instructions...
6. Back to stock rom...
Brick dopod C858
ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
Hello freind,
I have been downloaded the above "Remove_HARD-SPL_On_The_Wing.rar" files and flash it to my Dopod C858 which has the Chiness language, I suppose to change the language from chinesse to Englis, After flashing the above files, now the phone is only in bootloader mode.
If you start the phone it will stuck on white screen and turn off.
Please help me how to revive my phone back.
Thanks and best regards
Jhemzz
Hey I'm having the same problem as most of these guys who tried the file. The phone just idles on the white Tmobile screen... does anyone know what to do or how to help?
Please and thank you!
angest90 said:
wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there
Click to expand...
Click to collapse
im having the same problem can anyone help me please?
hotsammysliz said:
im having the same problem can anyone help me please?
Click to expand...
Click to collapse
Being stuck at the Tmobile screen isn't a true brick. Just reflash your ROM. (If you're not HardSPL'd, reflash your RUU.)
Remove Hard SPL from bootloader
Hi,
Anyone out there knows if we can remove hardspl from bootloader of Wing. Problem is my mobile displays splash screen, then switch offs by itself. Its been quite some time that I have hardspled it and have been using it. But recently I am facing this issue, so I am trying to move to original RUU and try if it works.
So for that anyone knows if we can remove hardspl from bootloader, because I am only able to enter bootloader. Moreover I tried several original roms from Flash Center as well as through SD card as well, but still be SPL version is 4.70.yang. Anyone knows any other alternative.
Also, if anyone has faced similar problem then kindly advice how you resolved.
Thanks in advance!
Regards,
Pankaj

Help with my P4351

Hello friends, I need your help, to be trying
P4351 upgrade my cable took off from there, it is
nailed to the first screen (not the system starts
OS), just let me enter the Tricolor screen,
I tried many roms (both P4350, P4351 as)
with officials, as cooked, and give me error, with
the original Sell tells me Invalid ID, and the
The rom cooked tells me is corrupted, being that before
allow me to update with any rom.
My IPL is 4.24.0002
My SPL is 4.14.0000
For more information: my phone was bought in Paraguay.
I've tested with the official rom T-Mobile.
Anyone can help me?
thanks.
matuzalen said:
Hello friends, I need your help, to be trying
P4351 upgrade my cable took off from there, it is
nailed to the first screen (not the system starts
OS), just let me enter the Tricolor screen,
I tried many roms (both P4350, P4351 as)
with officials, as cooked, and give me error, with
the original Sell tells me Invalid ID, and the
The rom cooked tells me is corrupted, being that before
allow me to update with any rom.
My IPL is 4.24.0002
My SPL is 4.14.0000
For more information: my phone was bought in Paraguay.
I've tested with the official rom T-Mobile.
Anyone can help me?
thanks.
Click to expand...
Click to collapse
Oki, maybe i can help you.
Did your DROP your phone recently?
cause that's what happened to me, and it broke my camera button. so my device was forced to go to the bootloader screen (aka RGB screen).
mrbayn said:
Oki, maybe i can help you.
Did your DROP your phone recently?
cause that's what happened to me, and it broke my camera button. so my device was forced to go to the bootloader screen (aka RGB screen).
Click to expand...
Click to collapse
No, not been dropped, the problem arose because I took the
cable during the update.
Okay. On the RGB screen plug in your usb and run then run this:
http://www.mediafire.com/?yj1oz2m3mzm
Let me know how it does from here. If this works then i'll guide you the rest of the way.
I have tried with the file that I've been, but still
jumping the same error, ERROR [294] invalid vender ID, the update runs to the 1% and the phone is restarted and returned to the initial state.
Also thank you very much for your help!
First thing - Is your phone a Herald?
Because my last bit of advice was for the Wing..
Try to find your original ROM for your device.
The service provider that you have your cell pone through should have that stock ROM/Update.
Then make sure you're at the RGB screen when running the stock ROM.
Tribulattifather said:
First thing - Is your phone a Herald?
Because my last bit of advice was for the Wing..
Try to find your original ROM for your device.
The service provider that you have your cell pone through should have that stock ROM/Update.
Then make sure you're at the RGB screen when running the stock ROM.
Click to expand...
Click to collapse
Hi friend, my phone is Herald (HERA110), and it's runing on the screen RGB
1) Download THIS.
2) Flash with the above while on the RGB screen.
3) Run the HardSPL package.
4) Get back to RGB screen.
5) Flash any custom ROM for your device
^>^
I tried and nothing happened, I digue giving the same error, and
Phone will not start, and do not know what else to do, because I
the steps you give me the bottom of the letter or even so
does not work. You may no longer serve?

Categories

Resources