Database Info

Help Annoying ROM

1st things first complete noob i apologize for any stupidity in the following post. Right i have faria wm6 ROM on my phone it is unlocked and i did all the steps to installing as to the instructions on this forum. Now heres wots happening my device will not load past the boot screen where it says windows mobile unless i take the battery out, now i thought it might be because of the new american dst so i ran the microsoft cab to patch it up. Well no luck there i sync my time it lags so much so i take the battery out it resets to feb 2006 and it's fine. Also active sync is a pain when you click sync the bar comes up at the bottom and thats it no roatating arrows the softkey does not change to stop. Also when i configure my exchange it says message format and i can change to plain txt or html well wen i first used it i could change it to html but now its stuck on plain txt but i dont know whether thats a setting my exchange provider has to change on there sever - i dunno. But it all seems to revolve around active sync and the devices time. Please help or point me in the right direction because i would hate to go back to t-mobiles rom which is boring!
Any help much appreciated
P.S sorry if this has been posted many a time maybe looked in wrong place but plz post link.
Cheers Guys

dnlohara said:
1st things first complete noob i apologize for any stupidity in the following post. Right i have faria wm6 ROM on my phone it is unlocked and i did all the steps to installing as to the instructions on this forum. Now heres wots happening my device will not load past the boot screen where it says windows mobile unless i take the battery out, now i thought it might be because of the new american dst so i ran the microsoft cab to patch it up. Well no luck there i sync my time it lags so much so i take the battery out it resets to feb 2006 and it's fine. Also active sync is a pain when you click sync the bar comes up at the bottom and thats it no roatating arrows the softkey does not change to stop. Also when i configure my exchange it says message format and i can change to plain txt or html well wen i first used it i could change it to html but now its stuck on plain txt but i dont know whether thats a setting my exchange provider has to change on there sever - i dunno. But it all seems to revolve around active sync and the devices time. Please help or point me in the right direction because i would hate to go back to t-mobiles rom which is boring!
Any help much appreciated
P.S sorry if this has been posted many a time maybe looked in wrong place but plz post link.
Cheers Guys
Click to expand...
Click to collapse
This post makes no sense to me. First you say you can't boot past the 3rd splash screen (Windows MObile 6). Then you start talking about doing cab files and other stuff (which indicates you are past this screen and working on your device).
Please take a breath and give us more information and full details of exactly where you are at. You also have to tell us your current IPL, SPL, and OS versions that show when you boot the phone (we need exact numbers to be able to help). Is your phone a G3 or G4? What is the last / current ROM you have on your phone? Are you now able to get into your phone (ie: did you flash back)? Is your phone CID Unlocked?

Sorry for my confusing post. I am able to get past the boot screen if i take my battery out and put it back in but turning on normally It wont get past if you get what i mean. further explained below...
Heres my numbers: ipl is 2.21, spl 2.21 os 2.18 gsm 02.19.11 , it is CID unlocked, it was flashed to farias rom from t-mobiles latest rom. Ive flashed farias rom twice now going back to t-mobiles first in both instances.
The main problem i seem to get is with the devices time - i'll try to explain this as well as i can - if the devices time is set to now then it is really slow and active sync does not work and the today screen will only show the time and nothing else like messaging, live, tasks, calender etc. and if you reset the device it does not get past the boot screen. Taking the battery out therefore reseting the devices time it works great but changing the time back to now and it lags again. Hope you understand this
P.S. I have installed microsofts dst patch

dnlohara said:
Sorry for my confusing post. I am able to get past the boot screen if i take my battery out and put it back in but turning on normally It wont get past if you get what i mean. further explained below...
Heres my numbers: ipl is 2.21, spl 2.21 os 2.18 gsm 02.19.11 , it is CID unlocked, it was flashed to farias rom from t-mobiles latest rom. Ive flashed farias rom twice now going back to t-mobiles first in both instances.
Click to expand...
Click to collapse
I honestly don't know if this will help, but you might try flashing the latest TMobile US ROM to get you to 2.26 instead of 2.21
http://www.t-mobileapps.com/downloadcenter/Software_List.cfm?selDevice=24
Then flash Faria's over that. Note that the 2.26 ROM will put the 2.25 Radio on your phone. You may want to then get the 2.19 UK radio from the ftp site here and go back to that one (I find the 2.19 works better than the higher versions on WM6 for me).
Also (and maybe before doing what I just suggested) try either turning off BatteryStatus, or upgrading it to 1.04.201 Beta 3. There have been fixes and I had a lockup problem (I couldn't reboot my phone if the USB cord was plugged in and BatteryStatus 1.04.200 Beta 2 was running). I'll attach the cab to this post.
The main problem i seem to get is with the devices time - i'll try to explain this as well as i can - if the devices time is set to now then it is really slow and active sync does not work and the today screen will only show the time and nothing else like messaging, live, tasks, calender etc. and if you reset the device it does not get past the boot screen. Taking the battery out therefore reseting the devices time it works great but changing the time back to now and it lags again. Hope you understand this
Click to expand...
Click to collapse
Are you overclocking or anything? Have you installed other apps, or does it work this way right after installing Faria's WM6 rom?
Faria's WM6 ROM is very good and I've never seen stuff like this reported so it seems its something with your setup. You could try flashing the fixed mUn's ROM ( http://forum.xda-developers.com/showpost.php?p=1172977&postcount=361 ) and see if it behaves the same way. If it does then you have an issue with your phone it would seem. If it doesn't then its an interaction with software on the device.
P.S. I have installed microsofts dst patch
Click to expand...
Click to collapse
You don't have to install this on WM6.

Rom Issues

Hey Guys, im a newb here and I had a question about my unlocked AT&T Fuze.
I did a hard reset today because my system started acting up, after i did the hard reset, it almost seems like it deleted AT&T's rom and went back to the original raphael rom. Now my physical keyboard is mixed up (i.e. if i press the windows key in the top left corner, it types one) almost as if I had a standard unlocked touch pro that is non-branded. does anyone know how to fix this so the keyboard will go back to typing what is actually written on the keyboard or does anyone know where to get the AT&T rom.
Thanks
A.K.

Hi,
I suspect your unlocked AT&T Fuze is running an HTC TouchPRO ROM. Possibly put on there by whomever unlocked your device.
The following link contains a .CAB that will configure you keyboard layout for AT&T.
[CAB] Touch Pro Keyboard in Fuze ROM, and vice-versa
http://forum.xda-developers.com/showthread.php?t=474192
HTH,

Thank you,
ill try it out right now and see if it works, i really appreciate it.
also, while i was looking for an answer, i found a thread with a link to the original HTC Fuze rom, would it be wise to install the original rom or do you guys think i should keep the current rom?
thank you

Thanks, I ran the cab file and it worked.
I also figured out how to edit the registry so it would work as well.
Thanks again
A.K.

Soon-to-be TP2 owner questions

Hi
I am new here and will soon be getting my Telus HTC TP2 and unlocking it myself via mobileincanada.com i had a couple of questions:
will i have any trouble unlocking?
i am buying it used so do i have to clear the ESN before i can use it? or what should i know about the ESN?
can i install the apps, .cab files found in the other section? or do i have to find CDMA only apps? Do apps work for both GSM and CDMA?
can i reset to factory defaults from settings to eliminate the previous owners info and data? or is there a button key combination?
is there a way to make Opera the default browser on the Internet tab?
is there a way to apply a diferent theme without installing a different ROM (since i've read we cannot do that yet for CDMA)?
is there anything else i should know as a new owner/user?
this is all i can think of for the moment. any and all help is much appreciated
thanks!

1) CDMA TP2's cannot be unlocked as of yet, I know that the community is working diligently on it.
2)You can't "clear" the ESN, it's the electronic serial number unique to each phone, it's kinda strange that you're able to find one used already, what you should check to see is if the phone was reported stolen, so basically you need to call your carrier and check to see if you will be able to activate that phone on their network.
Here's a relate post on another forum (mostly regarding a sprint phone but same idea)
http://cellphoneforums.net/sprint-pcs/t224073-how-clear-sprint-esn.html
3)You can install just about any app you want as long as it's compatible or signed *scratches head* I think there's a tweak cab file on ppc geeks that enables unsigned apps here:
http://forum.ppcgeeks.com/showthread.php?t=78019
4)Yes, not sure what the button combo is for sprint but for my verizon tp2 it's
-make sure the phone is OFF
-hold the "volume down" (the button on the side with the "-" on it) AND the send key (green button)
-While holding said buttons, press the power on button (red button) and follow the onscreen prompts.
5)It already is.
6)You can always disable Touch Flo 3D from the Today options or even install SPB Mobile Shell (I think that's what it's called) for a different theme, but if you're just talking about normal windows mobile 6.1 today themes, just disable Touch Flo 3D from the today menu in your options screen (All settings) and install themes you normally would as with any other version of WinMo 6.1
7) Phone works best with a good data plan and just like any other windows mobile device, expect to do a soft-reset every other day. And be ready for people asking you if you got a new type of iphone or that IS an iphone or if your phone has anything to do with the iphone.

thanks for your quick reply however i do know for a fact that TELUS TP2's can be unlocked i just happened to come across one person who had difficulty. that's why i was asking.
actually here this is the people that do the unlocking and they have a video on there. if you pause at the right time you can see the IMEI which is strange to me since i though CDMA phones were supposed to have ESN.
Click here for the site that unlocks the TELUS TP2 and the video where you can see the IMEI and unlocking demonstration. its a youtube video but make sure you have the plugins or use an appropriate browser or something because i couldnt see it on IE but i could with Chrome.
actually looking at the video again there are 4 numbers titled:
IMEI
WEID (first letter a little hard to make out)
S/N (is this the ESN?)
P/N
im attaching a screenshot.

Hi subby! I think what's tripping people up is your use of the word "unlock".
From the article you posted, the summary states: "You can see how to enter the unlock code to unlock GSM on the Telus HTC Touch Pro 2 Worldwide Edition." This is talking about unlocking GSM.---
---When people in this forum talk about 'unlocking', they're referring to the ability to load a different Hard SPL, so that they can install WM 6.5 on the phone. These are two completely different uses of the word "unlock."
I'm not sure which one you meant in your original post, but the TP2 does NOT have a HSPL released for it. So, you're stuck with WM6.1 (until HTC releases WM 6.5 in a few days)
The phone's great, however. I'd def. recommend.

wm5 ROM for a bricked Cingular 8125 G4 Wizard

Good day.......
I am mailing out of real frustration.
I don't know if this is allowed.
I collected a cingular 8125 from a friend in the UK.
I noticed on starting up that there was Tmobile screen first before the windows mobile screen starts. I had no problem with the fone until i realised that i couldnt connect to my local networks GPRS service (who uses a phone that can't browse)
After scanning thru the site, i decided to flash the phone with Crasing's WM6.5 ROM after doing a HardSPL and i could browse and it was the perfect phone apart from the fact that it was real slow and hangs attimes.
It got worse so i got fed up and decided to revert it back to the original ROM and sort the browsing stuff with a network fix that someone on this site had told me.
I reverted the hardSPL and on installing the Tmobile ROM, it brought out an error message, tried with the Cingular ROM same thing.
So i tired reflashing by using a software called Flash Center and it started and stopped at the 1%.
Restarting my phone just shows me the bootloader screen and i have been battling it constantly for 3 weeks but to no avail
I have read almost all forums here, done almost all they ask to do, but nothing.
The only ROM that worked on it is the WIZARD love ROM but it using exactly 21mins to start up. Thot of downloading Faria/Molski WM5 ROM (cos i sorta prefer going back to WM5) but the links for their downloads are dead.
Please help/direct me to where i can see help cos i really need the phone like 2 weeks ago. I am most definitely depressed now.
Thanks.

Check here for all HTC Wizard WM5 OEM shipped ROMS. The one for Cingular is listed in there.
http://forum.xda-developers.com/wiki/index.php?title=HTC_Wizard_Windows_Mobile_5.0_Shipped_ROMs
You say the phone is a Cingular (G4 DOC version). Does it look like this one (click link ... http://www.brighthand.com/assets/4811.jpg ) with the Cingular logo on top left, etc?
Did you require the HardSPL to be able to flash to new ROM, or did you just use the SIM / CID unlocker using the Wizard Service Tool (note the Wizard Service Tool will only work for G3 DOC type device, not the G4 DOC devices)
You said you also removed the HardSPL. If you removed the HardSPL, then you can only flach the OEM ROMS (i.e., if yours is Cingular, then you can only flash the Cingular Stock ROM ... check link above and use Cingular 2.25 (click here ...
... http://www.4shared.com/file/BJUEhCC9/RUU_Wizard_Cingular_8125_WIZCN.html )
First do a battery pull, replace battery, then start device in bootloader mode (i.e., press and hold Camera button on side, then using the stylus press and release Reset button on same side. Do NOT power up the unit by trying to turn on using the Power button on top). Take note of IPL and SPL version that shows up on Bootloader (3 colour) screen. Then plug in USB and try re-flashing with Cingular OEM ROM.
After successful OEM ROM you can then try HardSPL again and re-flash to other ROMS. There are plenty of cooked WM5 and WM6.1 ROMS out there. The WM6.5 is too much (I think) for these devices. A neat clean simple WM5 or WM6.1 with overclocking works very good.
Regarding your settings for ISO, GPRS, WAP etc. you can look for a Netwrok Wizard cab file, and install ( heres the newest I could find ...
http://forum.xda-developers.com/attachment.php?attachmentid=121023&d=1223800573). This will install 6 files into the root Windows directory of the phone. Reboot the phone and you will notice the Network Wizard icon show up in the Settings/Connection control panel.
One of the files it installs is called provision.zip. You will want to update this by copying the following to the windows directory overwriting the old one. This contains all the settings for your phone. Once you copy this over, click on the wizard in the Connection Settings control panel, and it should give you options for Country and Cell Phone carrier/provider. Click away and it shoould automatically set up the correct info for WAP, GPRS, ISP, MMS, etc.
Good Luck. Let me know what happens.

WOW
Thanks for the response
I used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****

WOW
Thanks for the response
About the pix you reffered to? Yes thats exactly how my phone looks like
I had used the HardSPL to flash the new ROM.
I removed the HardSPL and the Olip in my IPL was changed back to the 2.26.0001, SPL 2.26.0001
I tried the cingular 2.25 ROM but it says it wasn't meant for the device and most times the RUU doesn't recognise the phone. Tried the Tmobile 2.26 same thing.
Also used crossbow WM5 AKU2.3 and AKU3.3 ROMs they worked but fails at 96%
The only ROMs that worked is Wizard Love ROM but it spends about 20mins to get to the part where it asks you to align screen and it doesn't move from there
Thanks for the info on the WM5/WM6 also the network wizard cab file. Really hope that phone works
I'm a pretty desperate guy right now cos i use the phone to trade and money is moving, she(money) is a *****
PS: My IPL/SPL is 2.26.0001

OK. Good info.
Not sure how you did it but somehow you managed to get the T-Mobile IPL/SPL on it, and yet it still recognizes it is Cingular. For one reason or another one aspect does not let the other load and vice versa. ????? Hhhmmmnnn ????
Here is what I would try.
1) I have attached a zip file called SoftSPL. Inside I have made an image file nk.nbf, which contains ONLY the 2.25.0001 IPL and SPL for the Cingular 8125.
Unzip this folder to your Desktop and then try to run only the "newromupdateutility_wizard_noid.exe". Remember, start the phone up in bootloader mode, connect via USB then run the "newrom...exe" file. If you get an error right away saying this is not the right update utility for the phone or something like that, then start over ... i.e., disconnect phone, pull battery, start phone in bootloader mode,reconnect via USB, but this second time try using the one called "2.exe". I found sometimes when I flashed ROMS the first one did not work and the second one (2.exe) did for me.
IF this works, once you get the 2.25.0001 IPL and SPL showing on the bootloader screen then start again (pull battery etc. same as above) but then re-flash back to the original Cingular OEM 2.25 ROM that you tried earlier (the original RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe). Try this and let me know how it goes.
If and when you get it back to the original Cingular ROM, if you get to this point, you can then start back like it was when phone was "new". It will still be SIM unlocked so you can use any carriers SIM card but you cannot flash other ROMs.
If you are going to try other ROMs, re-apply the HardSPL, but make sure you only use ROMs that have been cooked, say they are safe for G4 devices and do not have IPL/SPL in them. This means when you have it HardSPL'd you cannot, or should not use other carriers OEM ROM's such as T-Mobile 2.26 or 3.08.
Lastly, if you do like some of the "extra's" offered with WM6 or higher and do not like a slow phone and want to keep it fast like a WM5 ROM, then stick to either WM6.0 or WM6.1, clean (or what they call Vanilla) ROMs.
Good Luck. Give feedback of how it works out for you and pay attention to errors and messages and IPL/SPL etc. for reporting back and I can help you a little more.

Another thanks again.
I really owe you if and when my phone is finally done cos i think i am getting there.
But i successfully changed the IPL/SPL but on flashing the cingular ROM it says the RUU cannot see my phone and once it sees that it says the update utility cannot be used for my phone.
So what next?
Maybe the ROM is not the right one but i ensure it was meant for g4 tho"
Tried MUN-RUU but to no avail
Eagerly waiting your reply.
Thanks again

OK. YES. You are getting there.
You say the phone is now IPL/SPL 2.25.0001. It shows this on the 3 colour bootloader screen?
What did you run in order to flash; did you run the "newromupdateutility_wizard.exe", or "2.exe", or did you need to run the "START-sSPL.exe" to flash th nk.nbf file I made? (I don't think the "START-sSPL.exe" works from the bootloader screen...phone has to be booted to working status).
Here's what is next. I made a new nk.nbf which is the Cingular 2.25 OS, splash screens and 2.25 radio only. I removed the IPL/SPL and the Extended_ROM, and cooked this back to nk.nbf.
Download it from here .....
http://www.fileswap.com/dl/7WhstX82/nk.nbf.html
..... and copy this to the folder you made of the SoftSPL earlier (overwriting the other nk.nbf - you may want to save that as a back up)
Now try flashing this new nk.nbf again as you did for the IPL/SPL.
If it works, then let the phone boot up completely. Check it out. And then you can run the RUU for the original Cingular OEM once the phone is booted to get it back to Cingular OEM state (full IPL/SPL, OS, GSM, Extended_ROM, etc.)
From here (if you make it) then any further flashing of ROMs, you will want to flash G4 safe ROM's, and you can do this using the SoftSPL folder. Copy the nk.nbf from the custom ROM you want to flash into the SoftSPL folder and run the "START-sSPL.exe" with your phone connected (not in bootloader mode, has to be completely started up and recognized by ActiveSync, but you do not need to establish partnership ... just skip/cancel that part and phone will connect to ActiveSync as a "Guest").
Good Luck. Let me know how you make out with this.

Just to answer your questions.
I ran the "newromupdateutility_wizard.exe"
Would follow thy new instruction sire and get back to thee.....lol
Thanks again.

I am not here to say "Yipee, its done'
But rather to say that the universe, cingular and the god of communication might have just conspired against me.
Just when i think i would finally get my phone working after 3 weeks, a 2 yr old kid took my batteries and only God know where that batteries is now.
Tried to buy a new one but all i get is "Wow! that a pretty old uncommon phone here"
I intend to use an ac to dc converter and when i am done i would give you the feedback
Thanks
PS: Just wanted to give you the heads-up

So i found the battery early this a.m.
Flashed the phone with the ROM you uploaded and it was succesful but on starting it i get a green screen and its damn slow and doesn't even pass the spot where you are asked to align screen (i really do think that nothing happen and its still the Wizard Love ROM that its still booting into)
So I am still stuck?
Hmmm....

OK i guess there might be a psych diagnosis for what i am doing (posting excessive replies without any respond)
It just a worried person.
So i kept re-trying to flash the ROM on my phone about 2ce.
Then i noticed on the 2nd time at about 86% the phone seemed to restart itself into bootloader mode about 2-3X, so i thot the battery was running out. Decided to take it out and get it charged.
On plugging the battery back to the phone all i got was a white screen and starting it on bootloader mode OR hard-resetting still gives me that white screen. On removing the battery the phone flashes like once or twice.
Is this the end? The phone has brought an apocalypse on?
Been doing a lot of browsing for clues but nothing tangible yet.

God smiled on me and the phone started
Got the ROM you gave me flashed and its really refreshing to see the Windows Mobile logo again
But i am stuck at the align screen tho'
I tap and nothing happens unless i drag the target and it just moves around and get back to the original spot.
Thats the latest pal.

OOPS. I did not read all .... your posts ... I just answered your post at the end of the last page. Did not see these last 2.
This is a good sign that you get past the initial boot splash screens and make it to the Align Screen ... soft reset the phone again and look at the IPL SPL that shows on the screen. Is it 2.25.0001 or 2.26.0001?
If 2.25.0001 then let the phone boot up to the Align Screen (and if you cannot get past this then just leave it at this point). Plug back into computer and now try to flash Cingular OEM ROM 2.25 that you tried earlier using the stock file.
If this doesn't let you flash for the same reasons as before (i.e., Invalid RUU tool or Not correct operator) then extract the nk.nbf from the Stock Cingular ROM (right click on the Cingular RUU OEM exe and select "Extract here ...".) then copy the nk.nbf over to the Soft SPL folder and use the START-sSPL.exe and flash this way. (you can delete the rest of the files from the Extract process.
Good Luck. Let me know the IPL SPL you get.

I know my posts are getting sickening but i am really desperate.
Got some info about how to bypass the align screen online but couldn't get my phone to boot anymore.
Soft reset/Hard reset/Bootloader mode: All of it just shows a white screen and nothin more.
Any ideas?

PS:The last time i could start the phone the IPL/SPL was 2.25.0001.

Just want to add this cos i just noticed it:
1. Sometimes tapping the Camera button alone puts the phone on (tho' it shows that annoying white screen)
2. On connecting the phone to a PC the PC recognises it even tho' its off and once i put it on and that annoying white screen comes on, the PC gives the same sound as when a USB is detached.
Hope these info would help.
I"m really getting depressed now. Hope's looking dimmer.

OK. I am now suspecting that you may also have a battery problem. How old is the battery. Could be the battery no longer has enough capacity. It may charge but only hold a charge for very short time and voltage may be too low. Maybe enough power to keep some of the electronics "awake" but not enough to drive the LCD.
It is now IPL/SPL 2.25.0001 so it should be able to flash the Cingular OEM ROM. You may want to try a different battery. Other than this, if not a problem with the battery then I think maybe phone itself is coming to an end.
I would try the battery route, making sure you have a good power source, and then try to flash the stock Cingular ROM.
You can still get these batteries on ebay and phone as well. If you are going to spend any money then maybe instead consider a newer model phone on ebay. (if you are patient you can find very good deal ... I got the T-Mo MDA Vario version of the Wizard (WIZA200) for $25 plus shipping, brand new with a carrying case. It was an estate item from a salesman who passed away and phone was not used before he passed on. One man's misfortune, another man's luck. I am now selling this on ebay plus memory card and earphone here ... http://bit.ly/hDHxrW. I have two more on sale at ebay here... http://bit.ly/eV0zZh ... and here ... http://bit.ly/gLIiKh. I am selling 3 and I have upgraded to Touch Pro 2. Go with AT&T version as this can beused world wide on 3G in North America and is quad band GSM for use in rest of world)

WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments

WOW
Thanks Bud
I would change the batteries and really don't mind buying another one but the only problem is i am not in USA nor Canada except i give an address in the US to send it to.
PS: Got to the links and it was a bidding process that was over by the time i got there. If anything opens up you can holla at me.
Would get back to you if there are any new developments

Cheap battery on ebay ..
http://cgi.ebay.ca/New-Li-ion-Batte...652056?pt=PDA_Accessories&hash=item5d2d297c58
http://cgi.ebay.ca/Battery-HTC-Wiza...163910?pt=PDA_Accessories&hash=item45f7ebb846
Phone
Wizards
http://cgi.ebay.ca/HTC-MDA-Mobile-S...0528835033?pt=Cell_Phones&hash=item4cf50dc5d9

Unlock your TP2 for Free (So far Sim unlock)

I bought a used TP2 off of ebay the other day just to tinker with it. I've been playing with it for a week or so trying to unlock it, I know there is an unlocker made by Olipro/Cmonex available but I guess you have to pay for that. Although I have the Sprint TP2 and that one is Sim unlocked, but I was able to find a way to SIM lock/unlock it, I'm still trying to figure out how to turn Security off though, I mean setting Secu_Flag to 0. I I did a lot of searching but couldn't find any instructions about unlocking the TP2 for free. So here is what I found so far:
Step 1- HardSPL your TP2 (This is available for free)
Step 2- Load the following RUU rom to your TP2. It looks like this Rom when loaded to the RAM it enables some Atcmd commands that allows us to play with NV part of the ROM thus allowing us to Lock/Unlock: RUU_Signed.nbh (I couldn't post the link I need to post 8 times before I can) "mediafire.com/?n11beq12kk24hy5"
Step 3- Run the following Atcmd: (This sets the Simlock flags to 0 thus removing the Simlock:
[email protected]=0,1,code "where "code" is your MSL ( I set my MSL code to 000000 and found out that 22051978 worked too, I found this on the internet somewhere)
[email protected]=0,2,code
[email protected]=0,4,code
[email protected]=0,8,code
This only unlocks the SIM, I was able to toggle those on and Off on My Sprint TP2 without any problem. Now if only I can find the command that disables the Secu_Flag. I don't have a lot of experience with this maybe some of you guys have experience and could point me in the right direction to continue my small project I would appreciate it.

ccengineer said:
I bought a used TP2 off of ebay the other day just to tinker with it. I've been playing with it for a week or so trying to unlock it, I know there is an unlocker made by Olipro/Cmonex available but I guess you have to pay for that. Although I have the Sprint TP2 and that one is Sim unlocked, but I was able to find a way to SIM lock/unlock it, I'm still trying to figure out how to turn Security off though, I mean setting Secu_Flag to 0. I I did a lot of searching but couldn't find any instructions about unlocking the TP2 for free. So here is what I found so far:
Step 1- HardSPL your TP2 (This is available for free)
Step 2- Load the following RUU rom to your TP2. It looks like this Rom when loaded to the RAM it enables some Atcmd commands that allows us to play with NV part of the ROM thus allowing us to Lock/Unlock: RUU_Signed.nbh (I couldn't post the link I need to post 8 times before I can) "mediafire.com/?n11beq12kk24hy5"
Step 3- Run the following Atcmd: (This sets the Simlock flags to 0 thus removing the Simlock:
[email protected]=0,1,code "where "code" is your MSL ( I set my MSL code to 000000 and found out that 22051978 worked too, I found this on the internet somewhere)
[email protected]=0,2,code
[email protected]=0,4,code
[email protected]=0,8,code
This only unlocks the SIM, I was able to toggle those on and Off on My Sprint TP2 without any problem. Now if only I can find the command that disables the Secu_Flag. I don't have a lot of experience with this maybe some of you guys have experience and could point me in the right direction to continue my small project I would appreciate it.
Click to expand...
Click to collapse
so if i do this on a verizon tp2....it will sim unlock it so i can use other carriers....without costing me MONEY!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

corypaul said:
so if i do this on a verizon tp2....it will sim unlock it so i can use other carriers....without costing me MONEY!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Verizon is not US radio locked, so a Sim unlock should be all you need.

ccengineer said:
Verizon is not US radio locked, so a Sim unlock should be all you need.
Click to expand...
Click to collapse
so this would work on my verizon touch pro 2???

how do you issue these commands to the phone?

T_D_H said:
how do you issue these commands to the phone?
Click to expand...
Click to collapse
Hi there
Attached you will find a zip file containing two files RunATCommands.exe and result.txt. Create a new folder and unzip them to that folder.
You will also need to download pget.exe,prun.exe and pput.exe which you can find here: ( links have been blocked) in the same folder in addition to AtCmd.exe (Search for this using google)
Unzip the RunAtCommand.zip to the same folder where you saved the above p...exe files and Atcmd.exe. Make sure your phone is connected to activesync or windows mobile device center then run RunAtCommand.exe. You will have a form with a text box where you enter the AT commands you want to send to the phone. Click run command button, at the bottom you will get the result. If you are issuing a command that writes to the phone instead of just reading, and the result is 0, it's actually something like "0\r", you will have a success message too.
You might need .net framework installed on your PC too. and maybe you need to install EnableRapi.cab on your phone if you don't have it.
Let me know how it goes.

corypaul said:
so this would work on my verizon touch pro 2???
Click to expand...
Click to collapse
I don't have a Verizon TP2 phone to try it. I think it would.

ccengineer said:
I don't have a Verizon TP2 phone to try it. I think it would.
Click to expand...
Click to collapse
it dont....it only says the phone is sim unlock when turn the phone off from the software

corypaul said:
it dont....it only says the phone is sim unlock when turn the phone off from the software
Click to expand...
Click to collapse
Are you saying that you tried the above on a Verizon TP2 and it didn't work? Or are you saying that it does say the phone is Sim unlocked? What happened when you issued the at commands mentioned in the original post? Did you download pget,pput and prun and put atcmd.exe in the same folder as RunATcommands.exe?

ccengineer said:
Are you saying that you tried the above on a Verizon TP2 and it didn't work? Or are you saying that it does say the phone is Sim unlocked? What happened when you issued the at commands mentioned in the original post? Did you download pget,pput and prun and put atcmd.exe in the same folder as RunATcommands.exe?
Click to expand...
Click to collapse
yea i downloaded all of that and i issues the commands on the phone, i kept saying @SIMLOCK= 00 0 i think. Yes im saying this doesnt work, hold up wait. if you send meh that file atcmd.exe it might work. i,ve google all around and can not find itt. and i was saying if the phone is off, like in airplane mode it will say that my phone is sim unlocked
or you can email it to meh: [email protected]

corypaul said:
yea i downloaded all of that and i issues the commands on the phone, i kept saying @SIMLOCK= 00 0 i think. Yes im saying this doesnt work, hold up wait. if you send meh that file atcmd.exe it might work. i,ve google all around and can not find itt. and i was saying if the phone is off, like in airplane mode it will say that my phone is sim unlocked
Click to expand...
Click to collapse
If you don't have atcmd.exe then you don't have the basic requirements for this to work, so why are you saying it doesn't work? I'm baffled. How did you issue the commands if you don't have atcmd.exe? And how did you get back @Simlock=00 if you don't have atcmd? If you indeed got @Simlock=00 after issuing the command [email protected]?40 then your phone is sim unlocked. Try to insert a GSM sim card in it and try it. Tell me what do you get when you issue the command [email protected]?AA please.

ccengineer said:
If you don't have atcmd.exe than you don't have the basic requirements for this to work, so why are you saying it doesn't work? I'm baffled. How did you issue the commands if you don't have atcmd.exe? And how did you get back @Simlock=00 if you don't have atcmd? If you indeed got @Simlock=00 after issuing the command [email protected]?40 then your phone is sim unlocked. Try to insert a GSM sim card in it and try it. Tell me what do you get when you issue the command [email protected]?AA please.
Click to expand...
Click to collapse
ok well are you gonna tell meh where i can get the atcmd.exe file at or can you email it to meh.

i could have test this radio but i sold my spare motherboard of TP2 . but i will give it a try asap.

el_venga said:
i could have test this radio but i sold my spare motherboard of TP2 . but i will give it a try asap.
Click to expand...
Click to collapse
I wish I knew, I would have bought it from you for further testing. If anyone wants to sell their TP2 to me for a discount so I can do more testing on different versions of the TP2 please let me know.

Hey ccengineer, did you ever get yourself another tp2? Just noticed something interesting.
I put in a tmobile sim card into a Sprint deactivated tp2 and I got a voicemail notification even though the phone wouldn't register on the tmobile network. You surmised on the ppcgeeks thread that perhaps the US antennas or frequencies were not being assigned. However given that I am getting a voicemail notification every time I turn on the phone, I think the phone is able to talk to the towers. Perhaps there is a network ID blacklist in the NV Ram for Sprint phones.

The link on the first post is not working, can you upload the NBH file again please?

i want to try bur the file is miss...

please someone upload the patched nbh )

Was anyone able to get this working?

Anyone get it to work? Does this basically make the TP2 into a world phone? Any help is appreciated.