help! anyone dismantle the HTC diamond us version - Touch Diamond, MDA Compact IV Accessories

hi, i need a little help. i just open up my htd diamond sprint. to put back the magnet that the stylus get hooked on. but the problem is i got everything done but when replace the cover on the back before the screws. there is a wire that runs right along the side next to the vibration ball. does it go right next to it or in the edge. well i am afraid it might rub against it and burn up the wire. any suggestion? got pics. forgot to take a pic of mine.

Related

problem with s710

the up and down arows are not working anymore on the today screen. if i open the slide they are working. can somebody tell me wat is wrong please
It's possible the flex cable has come unplugged, there are 2 rubber spacers that are slightly glued together that keep it in place.
Couple of screws to remove the housing and you can make sure it's not popping off when it's closed. Could also be a software issue.

Stylus magnet gone

The magnet holding the stylus seems to have either come off its usual spot or is turned in another direction. But the stylus wasn't holding anymore. Today, I got to work and noticed I had lost the stylus. Is there any known fix for this? I never dropped the phone, it just wouldn't work one day.
Thanks for any help.
Did you open the Stylus? You can srew it (upper black part) up, where you can see the magnet that is hold by a plastic part: it cant move .... did someone fool you?
Greetz
Boris
Well, my stylus is lost now so it's too late. No, nobody was trying to trick me. Are you saying that the only magnet is in the tip of the stylus? The end that you write with? Because I believe I have another one.
with mine you cant write like a pencil only on the touch screen without ink ;-), its a touch pro without branding original from HTC. the magnet in it is placed in the inner stylus ca. 3 cm upwards from the "tip" ..., you can say just in the middle ..
Greetz
Boris
Well, mystylus was going into it's sleeve and not staying in, it was just sliding out. So, I don't know where the magnet was at all.
For me it seems that the contra part in the inner of your device (ferrum or magnetic) has moved or is broken so the magnetic stylus "found nothing to be magnetic with" hope you understand me, my english is worst .... You know that you need a little Power to remove the stylus from his hole. if you could test it with the other stylus that you still own (but must be for the TP!!), wether the stylus is hold or not.... and have a look in the inner of the stylus wether the magnet is there...
good night.... perhaps till tomorrow.... If you need a plan from the inner parts of the TP: i have one
Greetz
Boris
P.S. If you shake your device: Do you hear anything ??
Well, I tried but my replacement stylus didn't work. There is definitely a magnet missing inside the phone. At first it was tight, then it seemed blocked and now it just glides in and out.
So, can anyone give me any hints about what I can do to fix my stylus not sticking in its sleeve? I really need this fixed. Is it safe to open up a Fuze?
This happened to me today...
i have removed the battery, chip, microsd and then the back cover... a bit tricky but it was easy (folowing the dis/assembly guide), for mine the lower part didnt want to go out, so i pull out the speaker connector and then push it out.
and the other magnet was there... and it have a place in the back cover that i think it may be seen if you take the battery out... it have like a dent
now my problem is with the polarity... i dont know how to glue it ... it have 2 positions vertical or horizontal
the vertical position will attract the stylus but it seems not to enter completely
the horizontal will push it, but i dont know if it will hold it as is very hard to test it without adding glue and i will use exposy...
EDIT1: found where it go... its in the vertical position but it need to be tested (because the polarity is different dont know why) if you are going to glue it
EDIT2: i used a plastic card (old medic card, visa, ect) to pry out the back cover from the keyboard
Thanks
Many,many thanks to you.
Same situation so easy but the lose magnet not easy to find except by your tips. Ha, ha I love this forum, So many thanks to the people here who contribute helping each other
jorgepr13 said:
This happened to me today...
i have removed the battery, chip, microsd and then the back cover... a bit tricky but it was easy (folowing the dis/assembly guide), for mine the lower part didnt want to go out, so i pull out the speaker connector and then push it out.
and the other magnet was there... and it have a place in the back cover that i think it may be seen if you take the battery out... it have like a dent
now my problem is with the polarity... i dont know how to glue it ... it have 2 positions vertical or horizontal
the vertical position will attract the stylus but it seems not to enter completely
the horizontal will push it, but i dont know if it will hold it as is very hard to test it without adding glue and i will use exposy...
EDIT: found where it go... its in the vertical position but it need to be tested (because the polarity is different dont know why) if you are going to glue it
Click to expand...
Click to collapse

broken sound on fuze??

hey guys about a week ago all the sudden the speakers seem to have went on my device. I recently changed roms and i still cant hear anything. I first noticed when I slept in this week because the alarm was going off but no audio LOL
anyone have any tips or experience with this issue? I have a feeling its hardware but if any sort of firmware upgrade or anything will fix it id love to know!
if it is hardware related...anyone have a guide on how to crack this beast open and check the audio wiring out?
There is a Service Manual for this phone floating around.
Cracking open the case is easy. I just did so to fix the antenna contacts. Unfortunately I broke my speaker cables when reassembling it, so i will need to do this again when my replacement speaker comes in.
Take off the back battery cover and you will see four screws. Using a very small philips screwdriver, remove the four screws, then with a flat plastic probe (or your nails if they are long enough) separate the back case cover from the keyboard, starting from one side, around the top , then the other side. Leave the bottom for last as that has the USB connector holding it together. The speaker is attached to the back case cover near the top, and has a very short cable connecting it to the circuit board. Careful not to pull the back case off too hard or you can snap these thin cables.

Backlight doesn't come on unless i bend the phone

So on my Nexus 5, the backlight started going off randomly... tapping phone would bring it back..
Then eventually it went out and i had to bend/flex the phone and it would keep working a while..
I contacted support then, but one time i bent it a little to get it on and the frame (plastic outer edge cracked), doh.. Now, of course, they will not give me a warranty repair because the device is physically damaged. So i tried a new screen, no dice. Now i have two good screens and a phone that still wont work unless i bend the crap out of it. Anyone else see this problem? Worth trying to replace motherboard? or should i just sell parts (new screen i bought, old screen, battery, etc) and buy a whole new phone... There is one specific point where i can bend it and backlight comes on, but i cant find a short or loose connection anywhere. I have had the thing COMPLETELY apart and back together multiple times. I should mention, it works totally fine when backlight is off, just no backlight so i can only see it in super bright direct illumination.
Any ideas???
Take it to a mobile phone repair shop.
Sent from my Nexus 5 using Tapatalk
Fixed for now! Woohoo! Based on the position of where i had to flex it, i tried a little gap filler... a folded piece of paper, between the SIM slot and the back frame. With everything screwed back together, it just puts a little pressure on that area of the main board.
Now the only problem is the screen i bought is defective (lines all up and down it) so now i have to disassemble again to put the old one back in.... oh joy, now to return it through ebay... I'm sure that will work well. Either way, phone working again! FYI, this phone is REALLLY easy to take apart and put back together.
EDIT: F.. snapped the end off one of the little antenna cables (the black one, on the right when looking at the uncovered back of the phone) when redoing the screen. Anyone know what that is for? WiFi and cell data signals seem ok.. Looks like a diversity antenna for something, because of all the others at the tope. Maybe google will have an answer.
ramerco said:
EDIT: F.. snapped the end off one of the little antenna cables (the black one, on the right when looking at the uncovered back of the phone) when redoing the screen. Anyone know what that is for? WiFi and cell data signals seem ok.. Looks like a diversity antenna for something, because of all the others at the tope. Maybe google will have an answer.
Click to expand...
Click to collapse
Check Bluetooth/try calling/using data just to be sure.
Do not discuss something on how to make fool of insurance company or even an warranty, It's not allowed here. Thanks

[Q] Can this be repaired?

So I bought this off eBay to replace the screen and fix it, but when I opened it up I found this(look at pictures) one of the ribbon holders fell apart as I took off the tape. God knows how it was working. The drop must of shattered it. So any suggestions on what I should do, I was thinking some really strong tape to keep the ribbon in place but I doubt that will last very long. The bottom part that connects it is still in good shape.

Categories

Resources