【How-To】【32A】IF your update to new official rom went wrong。。。 - myTouch 3G, Magic Android Development

【How-To】【32A】IF your update to new official rom went wrong。。。
Here is some advices:
1、make a gold card.(If you cant get your CID,find it in other's device,make sure that you are belong to the same region, KHM for example)
here is the steps:
Qns wrt SG Htc Dream and SDcard
2、Download RUU pack:
http://rapidshare.com/files/267331547/RUU_Sapphire_HTC_Asia_WWE_2.53.707.2_SEA_test_signed_NoDriver.exe
3、Insert your gold card ,connect your G2 to your PC and power on.
4、Run RUU_Sapphire_HTC_Asia_WWE_2.16.707.3_SG_release_si gned_NoDriver.exe
Flash at your own RISK! You could brick your phone by doing the above.

the problem is, i can't find another device to looking for my CID, anyone know how to find the CID in other way?

Yes! The same problem! I can't find another one!

(*****This method might have your phone bricked, use on your own risk!*****)
There is an easy way to recover from this "Brick", if you have MyTouch 3G devices.
First off, you are going to need MyTouch 3G's original ROM(sappimg.nbh).
Connect your phone to your computer with Android SDK installed, and your phone's drivers.
open cmd, and go to your sdk's directory:
//
cd tools
fastboot devices
fastboot flash nbh sappimg.nbh
//after this step, you might get an error: Failed(.........).
//But don't be panic here, because after this step, your phone's original SPL and Radio are already flashed into your phone.
//If you get this error, please unplug your phone to your computer, and unplug your phone's battery for about 10 sec. and then plug in the battery again and restart your phone. and your phone should be stopped at the RUU screen.
//Then do the following:
fastboot devices
fastboot flash nbh sappimg.nbh
Then your phone should be restarted and your phone is fixed.
//
(*****This method might have your phone bricked, use on your own risk!*****)

it MAY be possible to just use a card formatted to FAT32, i bypassed perfect spl without using goldcard

1131022 said:
(*****This method might have your phone bricked, use on your own risk!*****)
There is an easy way to recover from this "Brick", if you have MyTouch 3G devices.
First off, you are going to need MyTouch 3G's original ROM(sappimg.nbh).
Connect your phone to your computer with Android SDK installed, and your phone's drivers.
open cmd, and go to your sdk's directory:
//
cd tools
fastboot devices
fastboot flash nbh sappimg.nbh
//after this step, you might get an error: Failed(.........).
//But don't be panic here, because after this step, your phone's original SPL and Radio are already flashed into your phone.
//If you get this error, please unplug your phone to your computer, and unplug your phone's battery for about 10 sec. and then plug in the battery again and restart your phone. and your phone should be stopped at the RUU screen.
//Then do the following:
fastboot devices
fastboot flash nbh sappimg.nbh
Then your phone should be restarted and your phone is fixed.
//
(*****This method might have your phone bricked, use on your own risk!*****)
Click to expand...
Click to collapse
This is good news! Now all I need is sappimg.nbh for my device! Device CID: VODAPC23, Device type 32A
Can somebody supply me with sapping.nbh for this CID?

same problem goldcard isn´t working

How can I get the original sappimg.nbh?
I have a friend with the same CID as mine... can I get it from there?
Sorry for the lame questions... :S

Hello again!
I have found that my device is Czech Vodafone Black HTC Magic (32A)
So I'm searching for a dump of the original ROM for this device or the RUU! Can somebody supply it PLEASE!
CID: VODAPC23
HTC Model :SAPPHIRE-D1
Part Number :99HFU071-00
Part Description :SKU,VF,Multilanguage,CZE,HTC Magic,HSUPA enable,4G/2G MCP,Sophisticate Black,w/o SIM Lock,SAPPHIRE-D1

gold card issues
those of you that are having probs with your gold cards, did you make sure you put in ur 'gold card' sd card in ur phone before you did the cat command?
so it gives you the ID of the card that's INSIDE the phone.

Related

Kaiser Flah SSPL 16% and it stops!!!

I tried it also to flash to another rom. But at 16% it stops and i dont now why but i cant repair the rom. When i reboot the kaiser phone he comes directly in bootloader mode.
The do nothing anymore, i tried to flash from sd or mtty. Nothing works.
By mtty, i get the error that the command boot is a false command.
So i think my phone is really ****t up. this is really the firt time in 3 years my phone stops and i cant find solutions on XDA.
I can found only this tread with :
For those of you had the phone stuck in bootloader mode after flash with SSPL stopping at 16%, follow these instructions to unbrick your phone:
1. Download mtty.exe
2. Disable activesync (connection settings -> uncheck "allow usb connections")
3. Connect your Kaiser to PC using USB cable.
4. Open mtty, select USB port and click OK.
5. Hit ENTER twice, you should see the "Cmd>" prompt.
6. Type the command "boot", you should see something like this:
Code:
Cmd> boot
InitDisplay: Display_Chip=1
No card inserted
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++After that device should boot WM6 again, you can now re-enable USB connections in activesync and flash HardSPL
But it won't work.
I hope somebody can help me a litlle.
Greeting Thetmar.
are you trying to flash a rom using sspl-kais.exe?? and then it got stuck at 16%??
Why you dont use hard spl??
have you read the wiki first before flashing your device??
carefull with mtty...can brick your phone forever
cheers
I'v used mtty ande the command set 16 0.
And my phone is working again perfectly, only i can't get another rom on it!! I't stuck on 0% with all the spl versions. And the computer says 260 communication error.
I think i go back to the shop and ask for another phone.
My buddy has no problem to flash it. And i had the same phone and have bseveral problems.
Many many downloads and software on this site but i think i tryed almost everything.
Already thanks for saving my phone
error 260 is an open port error, you can try changing usb ports, rebooting your pc, turning off firewalls/antivirus
and you still did not answer me, are you using sspl to flash your phone??? i seriously doubt there is anything wrong with the phone.

Poblem with reverting to original stocks

Hi there, I tired to issue my problem in some other threads, but without any response so far - probably my problem is more specific.
I was using AHEN 6.5-R6i Rom for few weeks when some time after charging my Raphael was not powering up at all. I presume no relation between Ahen rom and the problem (as described further).
I bought new battery and it occurred that probably power charging circuit was damaged, because it newer completed charging, the device was always very hot and discharged in few minutes even when turned off (until completely drained out). What is more the USB connector works only for charging (maybe damaged data connection circuit?).
As a result, before returning the device for guarantee servicing I wanted to downgrade all the roms to the original ones. As advised I started with Radio and OS stocks, but after bootloader update (from SD card, cause my USB doesn't work) I got only "upgrading ROM code error" and the device tries to load some ROM, but putting any on SD card doesn't work anymore.
Any suggestions how to cope with this situation?
If you need help please provide us with important information. So fill your signature first. Mainly if you have hard-spl or if you bought olipro cid unlock and what exactly you have done until now. Also wether your device is CDMA or GSM? If it is GSM than you have to first restore Stock Radio first, after that if you cid-unlocked the phone you have to relock it again. Than remove hard-spl and install stock ROM. But if your USB is broken, i think there is no chance to remove Hard-SPL neither to restore to stock. Remember that when you are in a bootloader and you do not see that the device is connected to activesync or Windows Mobile Device Center it does not mean that it is not connected. Just check you hear the sound indicating that something is connected to usb in vista or windows xp.
If you need help please provide us with important information. So fill your signature first.
=> done
Mainly if you have hard-spl or if you bought olipro cid unlock and what exactly you have done until now.
=> chnged SPL to OliNex, OS to AHEN 6.5-R6i, Radio to version required by AHEN rom
Also wether your device is CDMA or GSM? If it is GSM than you have to first restore Stock Radio first, after that if you cid-unlocked the phone you have to relock it again. Than remove hard-spl and install stock ROM.
=> I retracked the changes as indicated changing both radio and OS to original ones, but had just problem at last step = flashing oryginal SPL (because I made it from SD).
But if your USB is broken, i think there is no chance to remove Hard-SPL neither to restore to stock.
=> Hmm, anyway right now I am stack because bootloader is "loading ..." every time I reboot the device.
Remember that when you are in a bootloader and you do not see that the device is connected to activesync or Windows Mobile Device Center it does not mean that it is not connected. Just check you hear the sound indicating that something is connected to usb in vista or windows xp.
=> I tried to use some terminals to see if I can execute commands directly or see any output, but I haven't even succeeded to open the port. Maybe I am doing something wrong - I give it a try once more tonight.
So what version of SPL is bootloader showing? If it's showing something like 1.90.0000, you are in bootloader and USB circuit is not damaged you should be able to normaly flash ROM from your provider from bootloader. So download the ROM from your T-Mobile it should be some exe. When you see bootloader tricolor screen coonect usb cable from Touch Pro to computer and run the exe soubor with your desired ROM. It should work if everything is OK!
If your device is showing 1.90.OliNex, than i cant help you because i do not know how to remove Hard-SPL from bootloader, maybe it is possible, but for more experienced tech guy, who i am not
PS: Hope you did not bricked your device because Hard-SPL and removing Hard-SPL is all done with cable, you cant do it from SD, and you cant flash original SPL before removing Hard-SPL!
hmm, it seems that I have managed to flash, at least partly, the original SPL from SD card, cause it shows version 1.90.0000. Partly, because it states that the previalus rom update was not successful :-(
In this state (in boot loader mode) I can't even charge battery so I have to do it externaly. Connecting to PC doesn't work (PC USB and cable are fine). The only thing that change after connecting to USB charger is that device gets hot ...
i am sorry to say, that you probably bricked your device... Maybe someone could help with more advanced hardware, software support, but i am not the right person...You can try to put your device to service and hope they will not recognize what have you done, but it depends on your stock SPL version. I got czech T-Mobile and stock SPL was 1.69.0000, so maybe yours was the same...
Next time please read more carefully, search or ask someone if you are not still sure, things about flashing SPLs are very dangerous if they are not done carefully...
Can anyone help this guy? He tried to flash original SPL over Hard-SPL, and therefore it is not looking very well for him to unbrick his Touch Pro...
So ... I got it from the service and they changed the motherboard and the battery, no charges
It was brickes, because of cherging circuit issue.
Unfortunatley I send it back to service, because the loudspeaker is not working ...
Actually I am the same exact boat as the OP. My phone stopped charging and its because the USB port is broken. I need to change the phone back to stock but if its not charging its probably not going to get a connection to the computer either. I read that on at least the Hermes it was possible to flash from the SD card. This is not possible for the TP? Thanks
riotburn said:
Actually I am the same exact boat as the OP. My phone stopped charging and its because the USB port is broken. I need to change the phone back to stock but if its not charging its probably not going to get a connection to the computer either. I read that on at least the Hermes it was possible to flash from the SD card. This is not possible for the TP? Thanks
Click to expand...
Click to collapse
You can flash the ROM, radio, splash screens etc etc from SD card - you will then have to send the phone back with hard spl still installed as you need a usb connection to remove it.
Dont assume you cant get a usb data conenction though - try it and see!
I did try the connection, didn't work. How do you flash from the sdcard? I just dont want to brick it.
Please read this thread on how to flash (including how to flash from SD card).
Again, (assuming you have the correct hard SPL currently flashed) you can flash a ROM, radio & splash screens etc to your phone from the SD card (one at a time) but as previously said you need a USB connection to flash hard spl (dont attempt it from the sd card).
So, my Raphael arrived from service after the second repair (loudspeaker not working) - it seems all works this time
By the way, that is correct that a USB connection is necessary to flash hard spl, but .. I was desperate because the USB was broken, so I tried it from SD. The effect was good enough for the service - the Hard-SPL seemed to be reverted to oryginal one, however the booting was stacked at loading the ROM

how i can remoce cid via bootloader

hi , i cant connect my vox to pc ...
when i run bootloader i can see bootloader USB .. but pc not search .
How i can remove cid ;/
When i put on vox i see windows mobile ... and orange picture... and END .. please help me ;(
Why not tell a little about the history of this device and your motivation to change the CID?
- has it ever worked (Windows mobile coming up)?
- has it ever connected to a PC while operating (Active Sync or Device Center)?
- do you know what the CID is good for?
- what makes you want to change the CID?
really sory for my english ... ;(
active sync dont search phone dont connect.
when i put on phone i see windows mobile loading next i see orange picture and the end STOP ... when i flash phone sd card i change name file next i put on bootloader and error: invalid certificate and phone off.
Well - it seems like the device does not boot correctly any longer.
First try to re-initialize the device:
- press both soft-keys and keep them pushed
- push the power on button (keep the two hotkeys pressed still) until the green light comes on, release power button
- still keep your fingers on the two softkeys until you see a prompt on the screen
- push the "send button" (Green Call button) to reset the device
If this does not help, you will need to re-flash the original ROM first to make sure that the device has no HW problem. Flashing is possible in basically two ways:
- via a connection to the PC (ActiveSync is NOT required)
- via SD card (special card setup required, aka "Gold Card")
I recommend the 1.st option. What you need is a PC, the orginal ROM from the vendor (I suspect Orange for device) and the Updateprogram for this ROM. SW + Updateprogram is usually one package.
Once you have all this:
1. Enter Bootloader on the device:
-- switch off
-- push camera key and keep pushed
-- insert USB connected to PC
-- wait for the 3-color screen to appear
2. start the update program on PC and follow instructions
I never did the last method - so try the other two first.
swiniaa said:
hi , i cant connect my vox to pc ...
when i run bootloader i can see bootloader USB
Click to expand...
Click to collapse
screen on pspc with tricolour ?
.. but pc not search .
Click to expand...
Click to collapse
in this state pspc acts not as pocket, but as raw device
How i can remove cid ;/
(
Click to expand...
Click to collapse
by flashing spl from http://forum.xda-developers.com/showthread.php?t=330909
dammm doesnt work ...
Code:
http://images40.fotosik.pl/241/e94544a52734cb51.jpg
244 invalid model id
or
270 update error
evry time
swiniaa said:
244 invalid model id
or
270 update error
evry time
Click to expand...
Click to collapse
Rootcause of your problem is that you try to load a ROM that does not fit to your device (CID mismatch). You will only be able to load such a ROM with the USPL active. You can only get the USPL active (afaik) with
- either OS running + USPL jump
- or HardSPL (replace the old SPL with USPL on device) the USPL
Afaik, you have no option to replace the bootloader SPL with the USPL that can bypass the CID check if you do not have the OS running! Also for "HardSPL" you will have to do the first method (via OS + Jump to USPL) one time. There is no gain with HardSPL unless you want to flash a new ROM many times a day (so for ROM chefs usually).
So again: Its so easy, follow my instructions in post #4
closed and i write new topic ... phone ON ...

[Q] HTC Sensation bootloop

Hello xda,
a friend of mine just gave me his HTC Sensation because it isnt running quite a while. The problem is that i haven't had a HTC device ever and I don't really know what to do and what information you need to help me so I'd be happy if u just tell me what information you need and I will try to get them for you.
The Information I got so far is:
- if I want to boot it, it stays at the HTC Logo
- CWM starts with some errors but you can't perform a wipe (just turns off)
- Bootloader starts as well but you can't perform wipe either, nor flash new CWM
- If i connect it with the computer while in fastboot it changes to "fastboot usb" but adb cannot find the device, though i installed first the drivers, lateron htc sync. Windows just calls it "myhtc"
bootloader says:
"PYRAMID PVT SHIP S-OFF RL
HBOOT . 1.27.1100
RADIO - 11.22.3594.07_M
OpenADSP-v02.6.0.2226.00.0131
eMMC-boot
Jan 13 2012, 17:33:34"
So what should I try to do or what information will you need.
I would be very happy if u can help me
fnstGoliath said:
Hello xda,
a friend of mine just gave me his HTC Sensation because it isnt running quite a while. The problem is that i haven't had a HTC device ever and I don't really know what to do and what information you need to help me so I'd be happy if u just tell me what information you need and I will try to get them for you.
The Information I got so far is:
- if I want to boot it, it stays at the HTC Logo
- CWM starts with some errors but you can't perform a wipe (just turns off)
- Bootloader starts as well but you can't perform wipe either, nor flash new CWM
- If i connect it with the computer while in fastboot it changes to "fastboot usb" but adb cannot find the device, though i installed first the drivers, lateron htc sync. Windows just calls it "myhtc"
bootloader says:
"PYRAMID PVT SHIP S-OFF RL
HBOOT . 1.27.1100
RADIO - 11.22.3594.07_M
OpenADSP-v02.6.0.2226.00.0131
eMMC-boot
Jan 13 2012, 17:33:34"
So what should I try to do or what information will you need.
I would be very happy if u can help me
Click to expand...
Click to collapse
Hi,
Go HERE
Install 4 EXT recovery,using one of the 3 methods available.(probably third)
Then,try to install ARHD ROM.(same guide)
No need to change the firmware.
So I just tried to flash 4 EXT Recovery but it doesn't work..
It finds the zip, ask me whether i want to start the update, i press vol up and "Update is in progres.." appears but nothing more, I'm waiting since 5 minutes and will probably have to power off the phone now.. the same happened when i tried to install cwm so theres something wrong with the bootloader?
What can I do now?
fnstGoliath said:
So I just tried to flash 4 EXT Recovery but it doesn't work..
It finds the zip, ask me whether i want to start the update, i press vol up and "Update is in progres.." appears but nothing more, I'm waiting since 5 minutes and will probably have to power off the phone now.. the same happened when i tried to install cwm so theres something wrong with the bootloader?
What can I do now?
Click to expand...
Click to collapse
Hi,
Maybe you should run a RUU.
Look HERE
I also thought about this but as I said adb doesn't find the device.
Since I never ran a RUU, can I still flash or do I have to get adb to run with the device.
Anyway, I cannot read out the CID of the device so if it is possible, which RUU should I flash?
Thanks for your help
fnstGoliath said:
I also thought about this but as I said adb doesn't find the device.
Since I never ran a RUU, can I still flash or do I have to get adb to run with the device.
Anyway, I cannot read out the CID of the device so if it is possible, which RUU should I flash?
Thanks for your help
Click to expand...
Click to collapse
Hi,
Try installing these windows 7 & 8 drivers (assuming you have a windows 7 or 8 machine)
Reboot your PC and see if your phone is recognized in ADB.
You are s-off,so you do not have to match it 100%
Just get a RUU that is close to your region or carrier.
If you get the wrong one,it is not a problem.
It will just give you an error.
Then,just try another.
)
Well I just installed those drivers but same result as before..
Windows says "MyHTC" and after i write "adb devices" into the cmd window it says "daemon not running. starting it on port 5037. daemon started succesfully. List of devices attached." and the next time i write adb devices it just says "List of devices attached".
Bootloader still says Fastboot USB.
So maybe there's something wrong with my adb?
Well can i flash RUU without adb finding my device or cant I?
fnstGoliath said:
Well I just installed those drivers but same result as before..
Windows says "MyHTC" and after i write "adb devices" into the cmd window it says "daemon not running. starting it on port 5037. daemon started succesfully. List of devices attached." and the next time i write adb devices it just says "List of devices attached".
Bootloader still says Fastboot USB.
So maybe there's something wrong with my adb?
Well can i flash RUU without adb finding my device or cant I?
Click to expand...
Click to collapse
Hi,
Not sure what is happening with your ADB.
Look HERE for help.
In order to run a RUU ,you need to put the bootloader into fastboot,and plug in the USB.
It should show what yours is showing.
So, it should work.
After "List of devices attached" there is no device shown, I didn't leave anything adb shows, so this is still right? Usually it always shows my device ^^
So my adb is probably not running right or it is about my phone
So my next step should be adb showing my device and therefore reinstall android sdk, java, stuff until it might show the phone
or just do something with the phone?
I still think that i cannot run a ruu without any device shown? Didnt really get an answer on this question I guess or I didnt realize it
fnstGoliath said:
After "List of devices attached" there is no device shown, I didn't leave anything adb shows, so this is still right? Usually it always shows my device ^^
So my adb is probably not running right or it is about my phone
So my next step should be adb showing my device and therefore reinstall android sdk, java, stuff until it might show the phone
or just do something with the phone?
I still think that i cannot run a ruu without any device shown? Didnt really get an answer on this question I guess or I didnt realize it
Click to expand...
Click to collapse
Hi,
Just run the RUU.
It will only show error if it does not work.
No big deal,and no damage done.
Just try another one.
if you enable usb debugging might help too
Well.. I just started "RUU_Pyramid_HTC_Europe_1.50.401.1_Radio_10.56.9035.00U_10.14.9035.01_M_release_223042_signed" and everything went fine until installation, no errors at all. Now the installer is stuck at "restarting bootloader" (or something equal, the installation is german) and the phone didnt do anything at all. It's now 15 minutes since the installation started so I probably will try another one but isn't it weird that ther is no error at all?
What should I do if the next RUU does exactly the same?
*edit:
just seeing page 2. How should I enable usb debugging without booting the phone?
*edit2:
second RUU: Same thing, no error but it didnt go further then "Restarting bootloader".
What to do now?
Any further Ideas what I could try?
Puuuush
fnstGoliath said:
Any further Ideas what I could try?
Puuuush
Click to expand...
Click to collapse
Put phone into bootloader then connect to pc and run the RUU
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
The phone was in fastboot usb while running the ruu for sure ..
fnstGoliath said:
The phone was in fastboot usb while running the ruu for sure ..
Click to expand...
Click to collapse
Hi,
Try running a RUU with the same radio (11.22) that you have installed.
You will not damage the phone.
It is not always an exact science with RUU.
Sometimes it is just trial and error.
So it is often that there is no error at all?
I just thought flashing wrong RUU will cause an error and not stopping at restarting bootloader. And anyway the bootloader seems pretty broken since it is not flashing anything at all ^^
Still i gonna try it
fnstGoliath said:
So it is often that there is no error at all?
I just thought flashing wrong RUU will cause an error and not stopping at restarting bootloader. And anyway the bootloader seems pretty broken since it is not flashing anything at all ^^
Still i gonna try it
Click to expand...
Click to collapse
Hi,
Probably ,the only thing that will fix your problem is a RUU.
So,keep trying different ones until it works.
I finally managed to find the phone via adb! I think that's a great step.
The biggest problem is that I lose any contact to the phone when i reboot it into bootloader.
I can just boot the phone into recovery and use any other adb function but as soon as I boot it into bootloader I can't do anything anymore.
That's why I cannot use any fastboot commands to flash a zip, neither run a RUU completely i guess.
So I think that i need any rom to either flash via recovery or just via PC not using fastboot/bootloader at all.
Are there any possibilities for me now?
fnstGoliath said:
I finally managed to find the phone via adb! I think that's a great step.
The biggest problem is that I lose any contact to the phone when i reboot it into bootloader.
I can just boot the phone into recovery and use any other adb function but as soon as I boot it into bootloader I can't do anything anymore.
That's why I cannot use any fastboot commands to flash a zip, neither run a RUU completely i guess.
So I think that i need any rom to either flash via recovery or just via PC not using fastboot/bootloader at all.
Are there any possibilities for me now?
Click to expand...
Click to collapse
Hi,
Plug your phone into the PC.
Go to device manager,and where it says MyHTC,right click and update driver.
Browse to the windows 7 & 8 drivers I gave you earlier.
Update,unplug phone ,and reboot PC.
Get a RUU that shows 3.32 or 3.33 in the title,and matches your region
Pull your battery.
Put it back in,and hold volume down and power button together.
Scroll to fastboot.
Plug in usb and run RUU from the PC

Htc one mini M4 ATT - RUU FLASHING ERROR, DOESN'T RECOGNISE DEVICE DESPITE ADB FB DOE

Hi. I was given the M4 from a family member who's battery died during an OTA UPDATE, I have located the RUU for the exact phone and all meta data meet requirements, checks out ok. Installed htc mini sdk and drivers, put ruu in the same folder. I connected phone and put phone in fast boot (locked bootloader) and AM able to type fastbootvdevices and it reads my phone is connected. I type command to reboot to bootloader and it does so everything seems connected. Upon running the RUU after the first few steps and a reboot i get an error saying usb and phone are not connected.
Anyone can help? This is my first time using RUU, It seems stock recovery isn't available. Possibly in the original battery failure usb debugging was reset? And that could be the issue? Im willing to try suggestions and have rwad reams before posting, please if anyone can offer some advice that would be great, and illb donate to your endeavour. Thanks..
Paul Taraneh

Categories

Resources