Related
I'm new to convergence devices and i just bought an imate jam "used", didn't come with anything, but I would like to upgrade to the latest ROM. I tried reading the sticky thread on top, but i got confused. I followed the steps, but I couldn't find the file that he stated on there. Then I just tried to upgrade it by clicking "next" on the "welcome to device software update utility" window, but that also failed, it said, "the ROM update you're trying to install is not for the device". Can anyone guide me through this?
Hi
Explain your problem better. Some specifics please.
Maybe you just need to use cracked baupgradeut.exe utility, because you try to upgrade with rom that's correct for your device but from other vendor.
Hello, thanks for replying !
I'm trying to upgrade the ram by using the ROMs stored here: ftp://xda-developers.com/Magician/Shipped_ROMS/
I've tried several of them, but whenever it reaches the end, it keeps saying wrong country code. I thought mine was a WWE, but that didn't work and I tried the UK, that also didn't work.
Dear Friend,
You should dawnload Maupgrade_noID.exe and extract all files from the ROMs in ftp shipped and than put this Maupgrade file in the same folder with the extracted files from the ftp ROM and then run Maupgrade_noID.exe. First time you will get again wrong ID code but you will need to run again Maupgrade_noID.exe and it will work. Attached Maupgrade_noID.exe.
Hi there,
My currently installed Rom was RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1.exe. (thank you jester for you good job)
Nevertheless, this ROM is in English and I wanted to downgrade to a French One before the selling of my device.
I have tried to install the downgrade kit detailed in this topic : http://forum.xda-developers.com/showthread.php?t=267344
The first step went OK but while trying to make the secnd step, my qtek is blocked at the boot splash screen showing the Jesterz picture and red information about the SPL and so on on the upper left corner... without starting... The USB connexion is not detected so I can't do anything... While trying to install any ROM, the USB connection is not detected ang I get an error message...
Did I kill my phone ?
Please help ! Tell me that it's not dead....
Don't worry, its nowhere close to being dead. If you have superCid, then use the SD card image to restore in bootloader mode. However, if the Cid is locked, then you would need a utility that can unlock Cid without Activesync mode (coz in your case, you would not be able to get an Activesync connection). imei-check.co.uk has a utility ($38 i guess) that unlocks Cid in bootloader.--- else show it to a professional. (in my country, I would have to shell out around $20 to get such a problem fixed at a mobile repair shop)
illanz said:
... The USB connexion is not detected so I can't do anything... While trying to install any ROM, the USB connection is not detected ang I get an error message...
Did I kill my phone ?
Please help ! Tell me that it's not dead....
Click to expand...
Click to collapse
Just take out the battery for about 10 minutes and re-insert. If it does not re-start, do a soft resert with the stylus and hopefully you should be fine
Hy,please help!
after downgrade, it doesnt work anymore.... i mean... i cant start the mobile!
after the downgrade i disable the USB data cable and now the mobile is dead... it doesnt starts from the ON/OFF Button and even if i connect the USB cable it makes nothing! No Led on... nothing! absolutly DEAD!!!
I have tried to put off the battery all night long with no result.. but I have achieved to reach the bootloader mode by pressing the camera button while soft reseting and keeping the camera button pushed...
OMG, I have been so scared ! ! !
Try this in order to reach the bootloader:
Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and KEEP PRESSING camara button till appear the Boot Loader.)
it doesnt work
I seem to have a simular problem. this is my post in another topic. It seems to fit better here.
This is what I tired so far:....
I used the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_S hip-NoVendorID and it often hangs and was slow with Push Email over GPRS.
I tried to find a way to downgrade but hadn't had time sofar. When I logged on XDA Developers Site I saw there was a new Image.
So I thought Great I dont need to find how to downgrade.
I don't know what G4 and G3 is so as everybody let's try the higest best one.
I uploaded the RUU-Prophet-G4-AKU3.3-Jester-b1
Wrong...
Now as previously stated I get to the multicolor screen with IPL 2.09 and the SPL 2.20..0001 on the screen and that's it.
I can get to the bootloader and load the same image again and get the same result.
I can load another image on and it loads to 80 Percent and says error [326] Invalid Command This NBF cannot be used with your PDA Phone. Please check your NBF file.
If I try an older Version it tells me upgrad only
And when I try to upload the G3 version it tells me error[300] invalid upgrade tool. This upgrade utility canot be used for your PDA Phone. Please get newer Upgrade utility.
Trying to use the nf.nbf or the G3 with the ROMUpdateUtility_NoID of the G4 doesn't work either.
If I would like to do the downgrade tool I need a Active Sync connection which I don't have.
I have no more thoughts. Please Help.
If you would have just read the forums better you would have known if your device is a G3 or a G4. (read this!).
Now it appears you have tried both for an update. Which may possibly have bricked your phone.
But... first things first. Can you get into the bootloader? (read wiki HERE on how to do that).
If you can still get into the bootloader then there is still a possibility for updating.
Try upgrading with the latest Qtek rom (note: this is an official rom, this one works for both G3 and G4! And since it's the latest you should be able to upgrade to this one).
Instructions quoted from another post of me:
You could try the 2.20 qtek rom which seems to be working well for quite some people (found here).
Although you have to make sure you read that thread good and use the ROMUpdateUtility_NoID.exe (found here ) to upgrade.
Update instructions:
1: With the qtek 2.20 rom you need to extract the zip and the exe file in the zip with WinRAR.
2: Then there is one folder called 'OutputFile' and a folder called 'RUU_TOOLS'.
Inside the RUU_TOOLS there is prophet and in that one WWE, when you go through them and in the WWE folder you see a bunch of files (readme.doc, enterbootloader.exe etc etc).
You need to copy ROMUpdateUtility_NoID.exe to the WWE folder with all the files. And you also need to copy the 'nk.nbf' file to the WWE folder (from the 'OutputFile' folder).
3: And then you need to put your phone in bootloader mode and run ROMUpdateUtility_NoID.exe to upgrade, which should work nicely then.
Click to expand...
Click to collapse
This should give you a good enough idea of what to do. This should work (new rom combined with no NoID updater).
However, if it's impossible to get yourself into the bootloader your options of upgrading your device are getting smaller.
Downgrading of a complete rom is only possible on a CID unlocked G3 (when it's CID unlocked you would know! because you would have done that yourself) and not on a G4 device.
Flasing a G3 device with a G4 rom or G4 device with a G3 rom might possibly turn your phone into a brick. This can easily be avoided by reading the forums properly and know what you are doing.
If anything (even if it's a small thing) is not completely clear to you about upgrading/downgrading your device I'd recommend not doing so.
edit: oh yeah... if you have a G4 device (which you should know by now) you cannot downgrade from this rom (well, only via a payed online service). And when you have a G3 device you could try and CID unlock it (read wiki + forums) before you want to downgrade, or don't downgrade at all.
But whatever you do, don't try to downgrade it without doing any of those things because you'll get into trouble. (to put it down bluntly)
illanz said:
I have tried to put off the battery all night long with no result.. but I have achieved to reach the bootloader mode by pressing the camera button while soft reseting and keeping the camera button pushed...
OMG, I have been so scared ! ! !
Click to expand...
Click to collapse
If you have reached the bootloader screen, just run my installer (or any official ROM) to get your phone working again.
My Prophet Died
I need help, to restore my Prophet, i upgrade wrong rom, i need will try the SD Backup, where can i see this process ?
Sorry my Inglish is too bad.
I've merged a couple of threads under this one, as they are all about the same problem (mostly)
Opening a new thread for the same problem isnt very useful
Hi RaptorRVL
Thank you very much for your patience in resuming all this for me.
I do try to read the forum but it isn't like a manual where you find the procedure stepby step. Like the G3 and G4 version I have newer come across until now. Sorry.
I tried the image you metioned and I have the result that at 80% it tells me error [326] Invalid Command This NBF cannot be used with your PDA Phone. Please check your NBF file
Any more thoughts?
As you seem to be an expert Can you let me know more about goldcard solution.
Cheers
Mick
From a readme I once found inside an update:
* ERROR [320~328] : INVALID COMMAND
These errors seldom occur. However, if one of these errors occur, it could not be recovered and the device had to be sent back to the customer service center. In this case, you have to flash a new ROM code.
Click to expand...
Click to collapse
Doesn't sound too good really. Maybe someone else here on the forums know what to do with this error :/
You did use the ROMUpdateUtility_NoID.exe and not the normal updater right? Can remember someone getting a similar error when using the wrong updater, but I'm not sure about that though...
edit: try doing a search on the prophet forums for "INVALID COMMAND" maybe there is a helpful post in there somewhere...
THANKS!! I was worried b/c i had the same problem today. I've been looking for so many threads abt this problem. Thanks for ur help guys!
same problem
so i have the same problem. I want to downgrade and it break at 95% invalid file. But now XDA is still alive. I can`t go into the bootloader but i tried this file: RUU_Prophet_220734_2207114_024721_NVID.exe
and now my Prophet is still running again. Hope i can help you. Good luck.
peter paul
P.S. sorry for my english, but its good to learn it again
I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum
flipside123 said:
I have been searching all over for this but it's probaly right in front of my face. I read that you need to get rid of SPL.nbh from official ROMS before flashing back with HardSPL. The problem is, the official T-Mobile Wing ROM that I downloaded is an .exe file. How do I go about removing the SPL.nbh file since it doesn't display folder contents or anything, just runs the RUU?
Sorry for the double post, I realized I was in the wrong forum
Click to expand...
Click to collapse
I'm uploading a zip file which will have the entire thing already to go.
Just flash your device as you would with any other rom.
Hang tight the link will be available within 10 mins.
Thank you sir. Greatly appreciated
flipside123 said:
Thank you sir. Greatly appreciated
Click to expand...
Click to collapse
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM
flipside123 said:
One more question. I'm looking to keep HardSPL but I have to revert to original to upgrade ROMS don't I? I want to upgrade to your OT 6.5 ROM
Click to expand...
Click to collapse
Okay,
I thought you wanted to go back to the original T-Mobile rom.
If your trying to HARD-SPL your device to install one of my roms or another cooks roms then thats another story.
Please read my FAQ or one of the stickies.
Ok, I think I got it now. So I don't need to revert to the original ROM to flash it since I have HardSPL? Thanks for the help
wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there
I tried the file that you uploaded here...And it went thru the whole process of flashing the ROM, but after it updated my wing just stays on the T-Mobiel screen and never boots past that.
It had that open touch software on it and I don't want open touch. I want plan old WM 6.0 on there.
I called T-Mobile and got an offical 6.0 update from them, but when I try that one it gets to 1% then says it has a disconneted and I get a connection error.
ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
So does this work? The two people who did this had problems. I need the phone to be all stock so I can have t-mobile send a free replacement because the screen is going on this wing.
***EDIT:*** Oka so this is the same as http://forum.xda-developers.com/showthread.php?t=364543&page=2 the first time I tried it it froze at 15% on step 2 so I installed the RAPI CAB like it says. Step two completed, phone rebooted and had white screen then I got error 260 I think. I have the stock t-mobile rom on it and had it on before I did this but it still has the yang from when I did a hard spl. Is there another way to get it to stock or am I doing something wrong? Plug in phone, let it sync, run herald-uspl.exe hit enter and so forth.
***EDIT*** Ok so this time it completed but is now stuck at the T-Mobile screen and I am now unable to even flash because I can't get past it And that damn yang still shows up in bootloader. Well went into bootloader and flashed from there so phone works but the damn yang is still there. And on a side note: Has anyone ever had a problem with their screen going very dark after flashing a rom from here? Phone was fine then I flashed OTP v7.4 TouchFlo 2D Lite.nbh yesterday and at night screen started going dark, would light up when opened in keyboard mode, then switched and then both were very dark and hard to see. I then flashed to OTP v7.3.1 TouchFlo 2D Final.nbh and still dark. Then I flashed to stock rom and have been able to see the screen since.
This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4
smokeingit said:
This is stupid easy to do... im shocked there isnt a post going into detail.
5 steps to going back.
http://forum.xda-developers.com/showpost.php?p=2998657&postcount=4
Click to expand...
Click to collapse
Did not work. Do I need to install the cab files again? I know I deleted a file out of the stock rom so it would not overwrite or verify or something but I put that file back, should I not have? This has been a few weeks and still can't get the yang off. Screen on my girls phone is almost dead, she can't even slide it any more so I need to fix the spl so I can send back to t-mobile....anyone ?
this is what i do to get back to the tmobile orginal. download the software from tmobile. I downloaded the newest update from tmobile site. REMOVE YOUR SD CARD. Connected my phone via usb. Launched the update. It has never failed me yet. It is just like updating your phone. tmobile has to take it, it is their update. They sent me a new phone noproblem, matter of fact i have to do it again, the back on the phone keeps getting loose on me. so they are sending me another phone again. hope this helps.
Alternatively you can use the combination of uspl and stock rom ruu to return your device to stock tmobile rom...
1. Enter in to uspl like you were falshing one of ttran001 roms... You can get this HERALD-USPL-beta3 from http://rapidshare.com/files/79249048/Flash_Center.rar
2. ONLY use steps 1 and 2 from the black screen (getting the white screen on your device)...
3. For step 3 in the flasher exit out of the black screen (windows cmd screen) by pressing ctrl+C...
4. Fire up the official ruu from tmobile found here http://forum.xda-developers.com/showthread.php?t=358030 or alternatively if you have a tmobile account still active you can get the most up to date rom from http://www.t-mobile.com/wmupgrade/
5. Fallow on screen instructions...
6. Back to stock rom...
Brick dopod C858
ttran001 said:
Done:
Remove HARD-SPL On The Wing
This is the same tool used to flash your device when it was not HARD-SPL.
I replaced the RUU_Signed file and SPL.nh file already.
It will bring your wing back to the stanard rom as when you first got it.
Click to expand...
Click to collapse
Hello freind,
I have been downloaded the above "Remove_HARD-SPL_On_The_Wing.rar" files and flash it to my Dopod C858 which has the Chiness language, I suppose to change the language from chinesse to Englis, After flashing the above files, now the phone is only in bootloader mode.
If you start the phone it will stuck on white screen and turn off.
Please help me how to revive my phone back.
Thanks and best regards
Jhemzz
Hey I'm having the same problem as most of these guys who tried the file. The phone just idles on the white Tmobile screen... does anyone know what to do or how to help?
Please and thank you!
angest90 said:
wen i did this i think i bricked my fone now its at the tmobile screen and it jus staying there
Click to expand...
Click to collapse
im having the same problem can anyone help me please?
hotsammysliz said:
im having the same problem can anyone help me please?
Click to expand...
Click to collapse
Being stuck at the Tmobile screen isn't a true brick. Just reflash your ROM. (If you're not HardSPL'd, reflash your RUU.)
Remove Hard SPL from bootloader
Hi,
Anyone out there knows if we can remove hardspl from bootloader of Wing. Problem is my mobile displays splash screen, then switch offs by itself. Its been quite some time that I have hardspled it and have been using it. But recently I am facing this issue, so I am trying to move to original RUU and try if it works.
So for that anyone knows if we can remove hardspl from bootloader, because I am only able to enter bootloader. Moreover I tried several original roms from Flash Center as well as through SD card as well, but still be SPL version is 4.70.yang. Anyone knows any other alternative.
Also, if anyone has faced similar problem then kindly advice how you resolved.
Thanks in advance!
Regards,
Pankaj
Hi,
I was doing a ROM update from an official HTC Magic unbranded ROM, it got stuck on 40% for about 3 hours, and I had to unplug, now all I get is the RUU or if the USB is mounted RUU USB.
Now, it just hangs @ 61% and nothing else.
Please see attachment.
Any help would be appreciated.
Andreo
Same problem with an htc hero and the official RUU.
Stop during update and nothing to do after.
I am interresting if you find a solution, else my hero will go to htc support...
I have even tried a flashing a HERO ROM, it goes through everything and says Installation complete, but back to that same screen in the picture!
I'm not an expert but sounds like a rom flash wont be enough by itself.
Looks like it failed when flashing the radio since ir got an RUU (Radio Unit Upgrade) mode only.
So something tells me that you're either forced to try to flash a new radio into it or send it to HTC support :S
But again i'm far from an expert in this matter!!!
You may restart the phone if it is not responding, do you have downloaded the latest update you should be able to unpack it usin 7zip and there will be a zip file in it with all images run
Code:
fasboot -w
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash userdata data.img
fastboot flash radio radio.img
this is not a guide so look around on xda if you don't know what the stuff above are.
Thanks! . . . also, it seems as though it used to hang just because the battery was not full enough, although, it didn't warn me and I couldn't tell the level.
A full charge and the rom went through and the phone is back on!
Again thanks.
Chers,
Andreo
PASS RUU
andreo1964 said:
I have even tried a flashing a HERO ROM, it goes through everything and says Installation complete, but back to that same screen in the picture!
Click to expand...
Click to collapse
You have to make yourself a GoldCard. Take the CID string using a Windows CE phone. But DON'T reverse the CID in Qmat. Worked fine for me after 2 days of despair...
andreo1964 said:
Hi,
I was doing a ROM update from an official HTC Magic unbranded ROM, it got stuck on 40% for about 3 hours, and I had to unplug, now all I get is the RUU or if the USB is mounted RUU USB.
Now, it just hangs @ 61% and nothing else.
Please see attachment.
Any help would be appreciated.
Andreo
Click to expand...
Click to collapse
i andreo i have the same problem with my magic, can you tell me how can i save my phone please
Make sure to get sappimg.nbh file and place it in the tools dir.
Run this command.
fastboot flash nbh sappimg.nbh
This will take you back to stock everything version 1.5.
Unfortunatly this doesnt work I get a Custom ID issue
henghim said:
Make sure to get sappimg.nbh file and place it in the tools dir.
Run this command.
fastboot flash nbh sappimg.nbh
This will take you back to stock everything version 1.5.
Click to expand...
Click to collapse
gymmy said:
Unfortunatly this doesnt work I get a Custom ID issue
Click to expand...
Click to collapse
hello, I had the same problem with the help of my colleagues from the Bulgarian, I fixed it without gold for cadets karta.Chek you just made the phone had such a site where you are setting up your serial number and go to where it e.sled enter the site and the HTC looking for old phone si.Download to update it if you go with the serial number if you do not poke around the net, Russians are brothers powwow original RUU, most important is to find for your original RUU telefon.Shtom find it, you put the USB cable and it puskash.This of me I hope I helped you
did you try this : http://forum.xda-developers.com/showthread.php?t=831044
ok, i apologize off the bat because im new at this and need help. basically my friend updated my htc hero firmware from 1.5 (Stock) to 2.1 version and rooted it. well now my wifi is unable to connect, my phone lags, and my internet is all out of wack. so i proceeded to take it back to original version and have been unsuccessful. I have downloaded two different ruu's because i am having trouble finding the stock ruu. I have tried on the RUU_Hero_C_Sprint_1.29.651.1 now i connect my phone to my pc (windows xp) and i turn on debugging and use htc sync which the phone will connect to my pc. i open up the ruu and it runs and acts like it is working then gives me error code 140- bootloader version error. then i use RUU_Hero_HTC_WWE_1.76.405.1 and it does the exact same thing and gives me error code 130- Model ID Error. I have no idea what to do or how to fix it. If anyone could give me some advice or help I would GREATLY appreciate it cause i just want my phone back. Thank you for reading. and ill do my best to provide anymore info if you need it.
fixed
i was using the wrong ruu i was using gsm when i should have been using cdma
try Cyanogenmod and you will not have this problems