Could someone please help me, my phone is stuck in the tricolor mode because i accidently clicked on the sync button on my pc when i shouldve unchecked the connect through usb on active sync. Ive read the help pages but just cant find anyone with this same mistake. please reply.
go to bootloader and flash again from there, just execute KaiserCustomRUU.exe, it will recognize your kaiser
Power down device, hold Camera Button, plug in USB. It'll load into bootloader ready for a usb flash.
Sisqo said:
go to bootloader and flash again from there, just execute KaiserCustomRUU.exe, it will recognize your kaiser
Click to expand...
Click to collapse
I just did and that worked! Whew thanks so much, now Im back in buisness!
Hi, please use the existing "Stuck in bootloader thread" if you have any more problems, rather that starting a new one.
Glad it's working for you
Thanks
Dave
Hi ! I have a problem with my Kaiser ! The screen is black, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays black ! Is there a way to make my kaiser working ? (Sorry for my english)
Remove battery and then press power button 30 seconds or more.
Worked for me.
Assface said:
Remove battery and then press power button 30 seconds or more.
Worked for me.
Click to expand...
Click to collapse
it doesnt work ! I think there is a problem with spl , because this problem appears after unsuccessful hard spl installing ! I don know how to fix this
IP13 said:
Hi ! I have a problem with my Kaiser ! The screen is blank, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays blank ! Is there a way to make my kaiser working ? (Sorry for my english)
Click to expand...
Click to collapse
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
krouth said:
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
Click to expand...
Click to collapse
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
IP13 said:
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
Click to expand...
Click to collapse
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
krouth said:
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
Click to expand...
Click to collapse
Active sync doesnt recognize my Kaiser!
IP13 said:
Active sync doesnt recognize my Kaiser!
Click to expand...
Click to collapse
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
krouth said:
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
Click to expand...
Click to collapse
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
krouth said:
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
Click to expand...
Click to collapse
I cant install this rom because it shows me an error : "ERROR [260] CONNECTION
The Update Utillity cannot connect your PDA Phone . Please check that your USB cradle/cable is connected properly between the PC and your PDA phone .
Chech the following :
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC "
I have allready checked the cable (it works with my other PDA)
delower10 said:
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
Click to expand...
Click to collapse
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
IP13 said:
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
Click to expand...
Click to collapse
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
krouth said:
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
Click to expand...
Click to collapse
Yes ! I also get the blank screen after following all this steps !
IP13 said:
Yes ! I also get the blank screen after following all this steps !
Click to expand...
Click to collapse
I am not sure.... I have done some searching and ran across this thread:
http://forum.xda-developers.com/showthread.php?t=423486
It has numerous posts about problems people have experienced flashing - maybe you might get some insight there - or at least post your question there where more people might be monitoring the thread. Good luck!
Please take your issue to the right place, better than open a new thread, I sugest
http://forum.xda-developers.com/showthread.php?t=433835
Your situation should be taken by the right guys, not just gessing if this or that might solve the situation, male a post there
Also have a look at the sticky on the top, try to get Dave Shaw help
THx I will try to ask there ....
Fanning the flames.
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
tyler51773 said:
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
Click to expand...
Click to collapse
Thx man , appreciate this !!
i cant believe i did this but i have a sprint tp2 and i accidentally install the wrong rom, i installed 1.8b_Sense_2.5_2012_Full, and after the update the phone wont turn on so i cant even do the bootloader. and hard reset either, nothing is responding. is there any way i can get out of this with a working phone?? would the people at sprint be able to help? and please no smart ass comments im really bummed out about this right now
It should be ok if you only install a gsm rom. If you installed a gsm unlocker than it is bricked. Just push the bootloader buttons with the phone off. If it doesn't go to bootloader it is bricked.
i installed the rom but i think the damn thing CAME with the radio unlocker inside the rom. i cant get into bootloader...
please help
If you can't get into bootloader and it wont turn on it is bricked.
Not to hijack the thread, but on the subject of bricking the phone...
I tried to install Hard SPL using SSPL Manual (downloaded from a link on ppcgeeks.com). I ran it from the phone, and the screen blanked as normal, but no USB device was detected after doing so and the manual Hard SPL would not work either.
I tried to reset and remove the battery. The phone will not turn on, will not enter boot loader mode, nothing! EXCEPT for one thing, when I plug in USB now, it is detected as a Qualcomm CDMA Technologies MSM. No driver though (Win 7 or Win XP).
Is there any way to recover from this?
Hi!
Download and install this:
_ftp://up.ppcgeeks.com/Touch%20Pro%202/Stock%20ROMs/RUU_Rhodium_W_Sprint_WWE_1.21.651.3_RS_1.96WF_NV_SPCS_1.42_0430_PRL60652_Ship.exe
I think it help you.
ted2001 said:
Hi!
Download and install this:
_ftp://up.ppcgeeks.com/Touch%20Pro%202/Stock%20ROMs/RUU_Rhodium_W_Sprint_WWE_1.21.651.3_RS_1.96WF_NV_SPCS_1.42_0430_PRL60652_Ship.exe
I think it help you.
Click to expand...
Click to collapse
Hi, I have the exact same issue as the member above. I tryed to go to the ftp site you reccomended, but can't download. Can you please help! I cant sleep or think of anything else. Can't believe I did that to my phone.
go here and then to touch pro 2 stock roms. ftp://up.ppcgeeks.com/
Thanks for the replies.
I can't load the stock ROM since the phone is not recognized by ActiveSync. While you can see it when you connect USB, it isn't actually usuable as there is no driver loaded for it. And many drivers I've tried for it do not work either.
I did try [to install the ROM] though just to make sure there was no magic going on behind the scenes, but no go.
EDIT: Grammer fix
Hi everyone,
My friend brought me a SS captivate at&t, it gotting bootloop AND PC DOES NOT RECOGNIZE EVERYTHING ABOUT it, recovery mode not work. i tried everything but no result, different oem usb cables, different pc with different os, it just charged the phone, nothing else. (not because of driver, my cappy works fine with these pc). I sent it to a few repair center, they used the Riff box (something like that) to flash direct to phone's mainboard but couldnt save it. Now it still hanging in at&t logo and just only charging when connecting to pc
Many thanks to any ideas can make it revive. Im in Vietnam with no at&t store here. Sorry about my bad english. Please help me!
Maybe this thread can offer some help... Captivate Connection Issues and Download Mode Help
Thread closed
4-2ndtwin said:
Maybe this thread can offer some help... Captivate Connection Issues and Download Mode Help
Click to expand...
Click to collapse
Yes, that is the thread that will help you.
I tried to downgrade my phone from the Oreo version to Nugat, the process started, but after the first reboot looks like the bricked is device, I tried to start in fastboot or recovery mode but it doesnt work...When I put the phone to charge nothing happens ... When I plug the phone to the pc does not recognize, however the windows plays the sound of the device when connects.
Can someone help me please? thank you!
Sorry for my bad english
hi
your from Brasil ??
leandro9000 said:
I tried to downgrade my phone from the Oreo version to Nugat, the process started, but after the first reboot looks like the bricked is device, I tried to start in fastboot or recovery mode but it doesnt work...When I put the phone to charge nothing happens ... When I plug the phone to the pc does not recognize, however the windows plays the sound of the device when connects.
Can someone help me please? thank you!
Sorry for my bad english
Click to expand...
Click to collapse
how did you be able to downgrade it?
no need help ....no return here...no need fix nothing