XDA Orbit 2 Help Needed. - Touch Cruise General

i attempted to run the .cab file for battery status, and when i did that it started installing then suddenly froze, then upon resetting the phone using the button on the bottom, it loads to the today screen as it were, and then freezes and will not respond atall, i know it isnt a fault with the touch screen as i have to enter my PIN before it gets to the today screen.
i am new to this so do a "dummies" guide as it was any help will be gratefully recieved.
Richard

Um i have a feeling that you may have a little problem here.
I dont know a brilliant fix for this other than to say to do a hard reset. BUT this well restore it to defult, factory settings as when you got it. So back up your phone of anything important before you do it.
To do it hold down the start and ok buttons and press the reset button. Wait for it to bring up the screen saying 'to restore press send'.
I cannot think of a reason but if its crashing i would think that it would be having problems with loading the files for today so i would guess that on the grounds that the install didnt finish it has, unfortunately corrupted some files.

ahh thanks, got it sorted now

Related

XDA Atom hardware problem?

Hello mates, I got my atom last week and since then it gets stuck and hangs for some time until it loads again whenever I hit the reset button.
Even hard reset doesn't help and either not taking the battery out...just need to hit the reset again and again until it comes back on...
I'm currently running the leaked ROM 20062017B1WWE
just to mention the issue started even with the older ROM installed.
Please help!
Hi.
Where did you get this ROM?
I'm looking for this rom WWE_R060221N do you have it?
Your rom is older or newer then WWE_R060221N?
Can you place in Emule so I can download?
Thank YOu
Re.
Hi there. I have a similar problem with my Atom (leaked ROM of course). Somehow, hitting SR button just leaves the initial screen with O2 logo hanging. You have to hit SR button several times or take out battery to make Atom boot. But, SR with O2 plus application works OK. Actually, it may get worse after awile and even taking out battery may not help to boot Atom. I had to re-run ROM upgrading to make my Atom boot after SR, but still hitting SR button makes Atom freeze.
Seems like we've got the same
problem mate....I really think that's a hardware problem because I tried to do everything and it still get stuck and hangs on the startup screen after a soft reset is performed. Anyways I'm gonna take my Atom back to the place I've bought it so they can check it and hopefully change it to a brand new one (thats what I hope so...)
Let me know how did you handle with your own problem.
You sure you aren't too impatient? With my Atom it takes around one minute to soft reset. It has XCPUScalar installed, I'm suspecting that this is part of the reason. The O2 logo stays on for maybe 20 seconds, then the WM5 screen for 20 and finally the Scalar stays on for at least the same before I can punch in my pin code.
Re
Thanks for your response..
I don't think I'm impatient as you said because I keep waiting for the Atom to load for at least 2-3 mins after the SR button is pressed, once I even tried leaving it hangs on the o2 screen for a whole night and it was still stuck...anyways I really don't know what to do.
Any other comments would be appreciated.
Cheers.
P.S
I never installed XCPUScalar on this device and never touched the overclocking settings.
Then I would say harware problem, yes.
I have the same problem since I bought it. I resolved in this way:
If you want to soft reset your unit press on/off button and softreset at the same time, you will see the option for hard reset but don't affraid just leave it in this option don't press anything and your atom will soft reset itself with no problems.
hi eljure, i tried your suggest and it worked on the first time i pressed the power button + soft reset button together, but then again it got stuck and hang on the o2 screen after the 2nd try.....anyways i had to wait again for like almost 1 hour until it loeded up again and that after all the resets i've done while i was waiting for it to load, only a hard reset worked after that.
so I really don't know what the problem is but it's freaking me out.
the store I bought it from said only next week they gonna get a new stock of the Atom so i'm stuck with it until then.
I have similar problem..maybe the same..the phone just hangs at O2 logo. I tried to press and hold power button and press reset button then it asks to press send and end button reset to factory factory default..after I press both button, it says device clean boot...reset to factory default!!..how long do i have to wait for it to set to factory default? or which way is the right way to hard reset? Anyone knows how to repair this problem, please help
I have similar problem..maybe the same..the phone just hangs at O2 logo. I tried to press and hold power button and press reset button then it asks to press send and end button reset to factory factory default..after I press both button, it says device clean boot...reset to factory default!!..how long do i have to wait for it to set to factory default? or which way is the right way to hard reset? Anyone knows how to repair this problem, please help
I have a similar problem where my O2 Atom will just switch off (go black) when I press the Soft Reset.
I do not get the O2 splash screen, and there is no response from any buttons or the power button. Even depressing the SR again does nothing. I have to remove and replace the battery to bring the unit back to life.
This has been happening since the phone was new (7 days ago).
ROM 20060123B1WWE.
Cheers,
Freedy.
I have the same trouble.
Hardware bug, obviously.

Suddenly I'm going extremely slowly... Help!

Ok, so far I've dumped the ROM and uploaded the kaiser-HardSPL and all was going lovely. However, after most of a day of pretty much inactivity I find the device suddenly goes very slowly. By which, I mean it can take several seconds to draw the screen.
Thinking this might be a rogue application using up all the processor cycles, I poked it up the bottom with the stick. (While doing this the first time, I held in power and camera just to see the boot loader text, but then I did it again with no buttons held.) It's a Vodafone device but it sat on the Vodafone splash screen for about 2-3 minutes then spent longer than that on the Windows Mobile screen before eventually dropping me into normality.
Except it's incredibly slow normality - I clicked on "start" and after a minute, it's not done anything yet.
Next step is a hard reset unless anyone has any better suggestion?
Help!
I assume you've pulled the battery?
Never assume anything... The full answer is, "No, but I have now"... I'm not sure that's going to do anything more than a soft (poke up the bottom) reset though. I'm now just waiting for the splash screen to subside while I'm typing this.
Having left it half an hour, while it went into standby and after noticing that the clock had stopped updating, I'm of the opinion that the already slow device has got slower...
Ok between 1 and 2 minutes to move from the splash screen to the "Windows Mobile" screen.
Now there's a turn up... After a further minute or so, I get a message, which has now cleared and gone back to the "Windows Mobile" screen before I had chance to copy it here. Basically it said that it had failed to boot either because I'd turned it off improperly or I'd installed something that it was opposed to. I should press send (I guess the green button) to reset to manufacturer's defaults.
Since that's my next stage anyway, I'll re-poke it with the pointy stick and press 'send' when it pops the message up. I'll put my trusty old Nokia N73 into flight mode and take a picture of the message so I can transcribe it here for everyone's amusement.
More news as it breaks.
I've now hit the 'send' button so it's doing a hard-reset. Meanwhile, here's the text it showed me:
Code:
The device is unable to boot be-
cause either you have turned off
the device incorrectly or tried to
install an application from untrusted
source. Press SEND to reset your
device or press any other button
to cancel. This operation will delete
all your personal data and restore
the device to its factory default
settings.
Nice. Ok, I'm at the 'tap the screen to set up your device' screen now.
Wonder what triggered all that nonsense then...
If you're like the rest of us and tooling around the all the fun programs in this forum, there's no telling.
I tell folks on computers, "Every piece of software you put on a machine is a liability to the operation of that machine." We can say that applies to this nifty little devices too.
I've had my phone experience the same symptoms you have posted here. Luckly for me a battery pull fixed mine. Sounds like the luck didn't spread much. Sorry.
Keep at it though. And don't fret the crashes. They do happen from time to time when you play hard.
So, a hard reset and a restore of a backup (Yes, I made a backup a few days ago even though I've been in the trade 20 years!) later, I'm back to normality. All I've done that's weird is install pof's loader and I can't see that's anything to do with it. What I was doing at the time of the slowdown was trying to connect to the wifi network at work. I thought the networking had just got itself tied in knots somehow but as the machine was even mega slow to boot, I can't really see that. At least I can still get back to square one at the moment.
I just need to create a .nbh out of the rom parts I dumped yesterday so that I can recover from anything more major...
Meanwhile, if you do a 'boot loader reset', would you expect it to say 'serial' if the USB isn't plugged in?
I'm starting to wonder if there is a major bug in the WiFi of the Tilt. There are some other threads on AT&T's site about this, and my work with WiFi on this unit has been dicey. Hmmmmm...

stuck on loading splash screen

Hi, first let me say im sorry if this has already been covered somewhere, i have spent all day searching the wiki and forum to no avail. If the solution is already here please point me in the direction and delete this thread.
I have just flashed my kaiser from the original vodafone WM6 ROM to Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700. At first everything seemed fine, then when i tried to restore the backup id created with sprite backup it restored, reset and now wont get past the loading screen. It shows the vodafone splash screen then duttys htc screen then goes back to vodafone.
I used Hardspl 3.29 before flashing. I tried hard reseting which made no difference. i cant get into the bootloader (tried the camera, power reset thing loads) and i cant connect to my pc as it wont go past the splash screen.
I had a look at MTTY but it doesnt give the options described in the instructions and after reading the warnings about MTTY decided i shouldnt mess around with what i dont understand.
Any help will be greatly apreciated, i love my phone and the idea that ive just broken it scares the crap out of me.
Thanks
Sandy
sandyfsx said:
Hi, first let me say im sorry if this has already been covered somewhere, i have spent all day searching the wiki and forum to no avail. If the solution is already here please point me in the direction and delete this thread.
I have just flashed my kaiser from the original vodafone WM6 ROM to Dutty's WM6.1 Hybrid v2 5.2.19716/5.2.19700. At first everything seemed fine, then when i tried to restore the backup id created with sprite backup it restored, reset and now wont get past the loading screen. It shows the vodafone splash screen then duttys htc screen then goes back to vodafone.
I used Hardspl 3.29 before flashing. I tried hard reseting which made no difference. i cant get into the bootloader (tried the camera, power reset thing loads) and i cant connect to my pc as it wont go past the splash screen.
I had a look at MTTY but it doesnt give the options described in the instructions and after reading the warnings about MTTY decided i shouldnt mess around with what i dont understand.
Any help will be greatly apreciated, i love my phone and the idea that ive just broken it scares the crap out of me.
Thanks
Sandy
Click to expand...
Click to collapse
first, are you SURE you can't get into bootloader?
I know it sounds stupid, but try REALLY pushing the camera button in while pushing the stylus into the reset hole. Once you get to the bootloader (tri-color screen), try flashing a different ROM
good luck
mbarvian said:
first, are you SURE you can't get into bootloader?
I know it sounds stupid, but try REALLY pushing the camera button in while pushing the stylus into the reset hole. Once you get to the bootloader (tri-color screen), try flashing a different ROM
good luck
Click to expand...
Click to collapse
I agree here a lot of people don't realize the Camera button is a two stage button. It stops at Half-Press then you can push again to get Full Press. You need a Full Press to get into bootloader.
Just to clarify.
Press and hold the camera button and at the same time insert stylus in reset hole and hold until bootloader comes up.
In other words, do not let up until bootloader shows. It should take around 2-3 seconds.
yea ive been doing that. After trying many times i have found that holding the camera button down for around 2 minutes after the htc dutty series screen comes up brings up a white screen with the error message;
"the device is unable to boot either because you have turned off the device incorrectly or tried to install an application from an untrusted source. press send to reset or any other key to cancel"
The message dissapears if i let go of the camera button, and resets back to the vodafone screen and stays there. If i press the send button same thing happens (just an idiot check but the send button is the green pick up button right?) ive tryed the enter button and both soft keys but all to the same result. I have tried holding down each button on that screen as well and the error message stays as long as i hold the button but when i let go it just goes back to the vodafone splash screen and stays there.
I have tried holding the stylus with the camera button all the way through to this error message, doesnt seem to make a difference.
just to clarify, ive done what you suggest and still cant get into the bootloader.
Thanks for any help, this is driving me mad.
hold the camera button and use the stylus to press the reset button, and continue holding the camera button until the bootloader screen pops up.
i used to let go the camera button as soon as the screen go black, but then it just reset the device instead of going into the bootloader...
oh forgot to mention. Shotly after the dutty series screen comes up i get the window appearing sound but nothing comes on screen. suggests to me that maybe its trying to tell me whatswrong but i can see what it is. maybe, i dunno..
theclueless said:
hold the camera button and use the stylus to press the reset button, and continue holding the camera button until the bootloader screen pops up.
i used to let go the camera button as soon as the screen go black, but then it just reset the device instead of going into the bootloader...
Click to expand...
Click to collapse
Im holding the camera button for around 2 minutes before it does anything, then i get the above error message.
Do you have a storage card installed?
yes. tried taking it out and doing the same thing. no different.
anything else i could try?
sandyfsx said:
Im holding the camera button for around 2 minutes before it does anything, then i get the above error message.
Click to expand...
Click to collapse
OK But are you also holding your stylus in the Reset Hole?
If yes, And you can't get into Bootloader, well I think you are "boned"
Yes im doing that. Boned? really? What about the error message that eventually comes up? isnt there anything i can do from there? Any other way of reseting it so maybe the bootloader works?
And if its really broken, do you recon my network will send me another or have i just properly voided the warranty?

Touch Pro will not Hard reset!

I started haveing issue with the device last night, the phone app was locking the phone up, i tried restoring from my sprite, but it didnt work.
I got it to a point where it workied, but for some reason it lost all my contacts and email settings.
Well I said screw it, ill just hard reset and start from scratch, after a soft reset, it hung on the "Touch Pro" screen withthe red text at the bottom, then just sits there.
If I hard boot it does the same thing.
any ideas?
go into bootloader and then flash a new ROM there.
Hold Volume down and reset. You will go to bootloader. Plug in USB and flash from there. No need to sd flash.
it will not go past the touch pro screen, still sitting like that now. I cannot even turn it off, just reset it and get back to the same spot.
did you take out the battery for a time? but you do that on your own risk... for me that doesnt sound good ...
greetz
Boris
Yep, the best I have been able to get is plugging the phone in and getting it to constantly reset itself.
BRICKED!
New ohone in the mail, hope to have it tomorrow,
Now, do I use my old sprite back up from a week or so ago, or start from scratch?
BD
best is to begin new, but for me that would take 1,5 days cause i know nothinh about UC; thats why i restore my spb backup... with differen Romeos version i had never problems ... take the rom upgrade mode...
Greetz
Boris
Once I get to the bootloader screen, how do I flash the rom?
What is the latest stock rom and what is best link to download?
I finally got to the hard reset warning screen. It says press "send" to reset. Everywhere else (including manual) it says to press "volume up". Anway, I pressed and released "send" but nothing happens. It seems frozen on teh warning screen. Or does it take a few minutes to hard reset.
PLEASE HELP!!!!!
Did you tried the method with settings => system => "Speicher löschen" ( in german; "eraze memory" or something like that in english) => input 1234??
Greetz
Boris
I sent mine back, it did nothing.
hard reset
i had to hard reset my htc touch pro as well because i unistalled a program and it wiped out like half the stock programs. this is what i did....
1). make sure you back everything up that you have on your phone.
2). shut off your phone
3). hold the volume down button and the enter button at the same time. (enter button is the big cirle center button)
4). while holding those two buttons in, press and hold the power button on the top until the popup appears on the screen. then just follow the steps and your phone should be like brand new again!!
Funny thing I did it the first time and it worked like a charm. But now i'm having trouble in doing it again?? any suggestions?? anyone???

[Q] Galaxy Nexus Boot Loop (stock)

I have an unlocked HSPA+ Galaxy Nexus imported from the UK to the US. Ordered from Negri Electronics.
It's not rooted or modded in any way.. Mainly because I don't know how to. As far as I know, it's running stock ICS.
I was using it normally, (using the fb messenger app if it makes any difference) when it suddenly rebooted by itself. The Google logo comes up, then the start up animation, and sometimes the home screen will appear but is not touch sensitive (i cannot slide it to unlock), and then it 'hangs' and the screen goes black. Repeat.
I've tried to fix this by myself and there's a video on youtube (sorry, noob here. can't post links. video is by robbidwv and title is "my galaxy nexus won't boot..") of the same problem that I have, but the posted solution doesn't work for me.
So far, I have entered Coin Mode and pressed Start. Entered Fastboot mode and gone into Recovery Mode (no options appear after that. it just starts booting up and the loop begins), and I've also tried Restart Bootloader.
I've almost given up. Now all I want is to extract my SMS, if they're still on my phone. I can't access the folders on my computer because it won't boot up and connect. Is there a way that I can extract my SMS by using DOS in either Coin Mode or Fastboot mode?
Or even better, does anyone have a solution to this boot loop problem? I'll contact Negri Electronics tomorrow and hopefully they can send me a replacement.
Please help!! Thanks
that problem just started happening with me an hour ago!!
i hate this!!
we need a solution please!
Hey guys, sorry about the issue.the major problem I see here is you wanting to retrieve your txt messages, which might be possible with a little Modding, but if yourwilling to lose them to get a working phone back, then this is what your going to have to do. Make sure your phone is completely off. Hold the 2 volume buttons and the power button together. You will get into a mode with an android Guy. Press the volume button up or down until it says reboot recovery at the top. Press the power button. It will rebootand come to a screen with an android. Hold volume up,down and power at the same time. A menu will come up. Go down to wipe data. Click it, and after it is done reboot. Your phone should work now.
If this helped you, or you simply appreciate me taking the time to write this out then please press the thanks button
Hey!
Thanks. Yeah I 'fixed' it already. I was just about to post something similar. After a while I just gave up on trying to recover my data. Good thing that Google syncs everything so the only issue would be recovering my messages, which I decided weren't worth sending it in for a repair which would probably not be able to recover anything anyway.
The thing I didn't know about was to press power + volume up WHILE on the recovery screen. I thought navigating to the recovery screen was it!
Still, this kind of sucks. I love my GNex, but I can't help but be slightly pissed seeing that my crappy iPhone 3GS never did this in the 2 years I had it. Oh well, hope it doesn't happen again!
hey guys! i also did a complete wipe on my phone and got it working again!
but i wonder why this happened in the first place?
last application i installed before the crash was double twist, i dunno why but i feel that it was the reason behind the boot loop!
Sorry for reviving this thread, but I just had this happen to me TWICE!
It happened to me first last Monday, the 23rd - the phone crashed when trying to send an email with an attachment - and went into a boot loop - Google logo would appear, no make it to the animation, and reboot....
I performed a full reset and things worked again. I didn't install all the apps I had before - figuring it must have been due to some app messing with the OS.
Well, it happened again to me yesterday! I was connecting to my bluetooth headset when the phone crashed and went into the boot loop. Full reset worked again, and I've installed even fewer apps - essentially only those that I use on a daily basis.
My phone is still on 4.0.1 and I'm hoping once 4.0.4 is pushed this may get resolved? I have a canadian GNex from Negri. I will call them again (I called the first time, but when the full reset worked I never contacted them again).
I would like to this this is a software issues, and not hardware.
I have the same problem. If you figure it out let me know.
Today my phone also entered a boot loop: [Google logo]->[black screen]->[vibration]->[Repeat]
I tried Recovery Mode, but this is what happens: (sorry for the link but I am not trusted with powerful tools such as outside links apparently, as I have not yet reached the maturity of a person with eight posts... )
dl(dot)dropbox(dot)com/u/53568097/Android.jpg
This is what I see when I navigate to Recovery Mode
For a split second I can see an image of an Android with spinning cogs in his innards, but then this little sad fellow appears. WTF is this?
EDIT:
Oh, and I'm running Android stock 4.0.2, never rooted or unlocked, Swedish. At the time when the phone started doing this, I was using Endomondo, and was about to set off on my bike when it died on me.
Stock ROM galaxy nexus bootlooping after wiping data also.
Hi,
My GNex went into a bootloop so i searched xda and found that factory reseting would be helping my prob. But after wiping the data also its still in going through the loop . Please help .:crying:

Categories

Resources