Help for upgrading to wm 6.1 via SD card Flash - JAM, MDA Compact, S100 Software Upgrading

My USB Mini port seems to be damaged. I can charge the phone but when i connect it to my PC, the orange light lits and the phone gets charged but it is not found by my pc. So pls let me know how can i upgrade to wm 6.1 through sd card flash.
The solution is:
U need
ntrw ftp://xda:[email protected]/Magician/Tools/Backup_tools1/ntrw.exe
wm6.1 nb1 file http://www.mediafire.com/?sharekey=02c513f13b6fba677f7ec40ada4772a6e04e75f6e8ebb871
If the 1st method doesnot work then u need the backup of existing rom Click here to know how to back up ur exsiting rom http://wiki.xda-developers.com/index.php?pagename=BackupExistingRom
the hex editor http://www.hhdsoftware.com/Download/free-hex-editor-neo.exe
Method 1:
write to the sd card using
ntrw write Cotulla6.1.O3.nb1 F:
F: is ur sd card drive
There will be an error saying parameter incorrect. dont worry. Insert the card into the phone and enter the bootloader( Power+Camera+ SOft reset). A message will come asking you to press power button to flash. Press the power button and wait for complete flashing. in the end there will be a error that checksum failed . dont worry and do soft reset. Hurray u now have wm6.1 on ur magician.
Method 2:
If this doesn't work try this.( U should have a backup copy of ur old rom nb1 file.)
copy the first 416 bytes of ur old rom to the 416 bytes of the rom downloaded using hex editor
write the new rom to the sd card and install as in method 1.

It's not possible to install my rom via SD card.
Sorry, it designed for RUU flashing only.

I was wondering this myself...
Are you sure, Cotulla, that following this procedure would fail with your ROM?

Please someone try and if sucessful pls upload the .nb1 file so that i can write it to SD card and flash it through SD card. Thank you in adavnce

I can dump my ROM for you if you're willing to test to flash it.

please. i will try on my o2. thanks

Here it comes: click. Password is xda-developers.com.

the file appears to be too small only 23 mb . coutulla's rom was somewhere around 50 mb. will this work. i will try tomorrow as i am outside & donot have pc access

That's because of compression, the file itself is 63.7 MB.
I was planning to try this as well, but I don't have a memory card at the moment.
Keep us posted and good luck

As MusikMonk stated, this file is compressed and crypted with 7z. Haven't you heard of 7z yet? It's about time!
I doubt it will brick your Magician, since it's not overwriting the bootloader. Thus you can always flash you beloved old ROM.

While writing the file to the memeory card i am getting this as output.
NTRW v2.00
Removeable media
Cylinders: 0:120
TracksPerCylinder: 255
SectorsPerTrack: 63
BytesPerSector: 512
bufsize is 65536
WriteFile(): Cotulla6.1.03.nb1 -- the Parameter is incorrect
When i put the memmory card in my PDA and enter the bootloader mode only the screen with Serial and v.1.02 is there and there is no option to install press power button.

You must have done something wrong when filling your SD card.
I get that "press power to flash" message.
I hope someone will eventually try to flash that file... otherwise I made a lot of effort for nothing :-(

So does it work or not???

I used 1 GB Memory card. The Problem Might be because of than. Pls Letme know what memory card u used. Shold I used 64/128 MD card instead of 1 GB. Pls Help

64MB is a few bytes too small, 128MB is sufficient. I used a 256MB card... maybe the boot loader is unable to read much bigger cards... if my 16 GB card were empty I could give it a try... ;-)

I tried to copy the Cotulla.nb1 file on my SD-card, but it doesn't work. I used a 2gb and 128mb card...
I copied the ntrw.exe and the Cotulla.nb1-file to c://user/username. Then I write "ntrw write Cotulla.nb1 j:" in the black DOS-Window and press enter. j: is my SD-card.
Now there appeare some lines of text and I can wait about 3 minutes until there comes something about a wrong parameter...
But as I understand it, this should be no problem.
But the problem is when I try to take a look on the SD-card, there comes a window, that says that I must format the card. I cant open it... When I take out the card from the card reader and put it inside again, I can see what is inside on the card. But there is only one folder with the size of only about 130kb and no ROM...
My OS is Vista.
What am I doing wrong???

Magician boot loader does not expect any file system on the SD card, thus ntrw writes the OS directly to the first sectors of your card. When you insert this card now anywhere Windows does not find any file system and recommends to format. That is correct (as long as don't answer yes) and shows writing WM6.1 was successful (given your card is big enough and failure free).
To make clear: you shouldn't be to browse that card in Explorer when you wrote WM6.1 on it.

Ok but if I put the card out of the reader und back again I can browse the card and there is nothing except of an 130kb small folder...
And if I put the card into my magician on bootloader, nothing happens...
What could be the reason for that?

I tried with 256 MB memory card I am gettin gthe same message while writing to card.
NTRW v2.00
Removeable media
Cylinders: 0:120
TracksPerCylinder: 255
SectorsPerTrack: 63
BytesPerSector: 512
bufsize is 65536
WriteFile(): Cotulla6.1.03.nb1 -- the Parameter is incorrect
And when I enter the bootloader mode with the card Inserted I get the message:
SD Download
==========
Sections=1
Not allow
update!
But with the same SD card when i write my old ROM( whic i had backed up) I get no error and when I insert the card and enter Bootloader mode I get the message :
SD Download
==========
Sections=1
Press Power to Flash
This means that there is some problem with the nb1 file . So kindly someone try it and post the results

one more thing. The backup.nb1 which i backed up from my sd card is 243 mb big. So i feel that the nb1 file which U extract from your card should also of around the same size and not 65 MB. Correct me if i am wrong.
I tried to extract nb1 file after writing ur rom to my sd card. it is also 243 mb big.

Related

Serious Problem encounted when Backup ROM image !!!!....HELP

After I successfully backup my O2 Mini existing ROM to the SD Card by the romupdate.exe. I used the ntrw.exe to convert the Image in the SD card to my computer. However, when i excute the command
> ntrw read backup.nb1 X:/
it return the followings..
>could not open backup.nb1 -- the volume does not contain a recognized file system. Pleas make sure that all requited file system drivers are loaded and that the colume is not corrupted.
I have tried other card reader (both 1.1 and 2.0) other computer and other SD card ( i am using LEXAR and Kingston 256 ) but the problem exists.
and the romupdate said the d2s command was success.
Why will it happen and
What can i do to fix this problem????
Thanks for your help....
use the command without the latest "/"
ntrw read backub.nb1 X:
JayEs said:
use the command without the latest "/"
ntrw read backub.nb1 X:
Click to expand...
Click to collapse
thx for your reply...
I have tried you's.....but it said...
> ntrw read backup.nb1 X:
> Could not lock backup.nb1 -- Access denied.
which os do u use?
which filesystem?
are u sure u have enough free discspace?
which kind of sd card do u use? (size, speed, brand)
attached image for you reference
JayEs said:
which os do u use?
which filesystem?
are u sure u have enough free discspace?
which kind of sd card do u use? (size, speed, brand)
Click to expand...
Click to collapse
OS: WinXP (NTFS)
PPC: XDA II Mini
I am sure i have enough HD space as well as the SD Card
I am using LEXAR and Kingston 256 SD, both ain't work
Thanks~~
You need to use a card reader and the drive X: should be the drive XP allocates to the SD card slot on your reader.
XP Assigns my SD reader to I: unless you have a lot of network drives on your PC it should be somewhere. The card needs to be in the card reader slot obviously and not the PDA.
I am also assuming that you are trying to write the Rom to your hard drive and not writing it back to the SD?
Hi there, looking at the dos screen you took, its telling you that you have already a file with that name in the folder. look, delete that file... and then try again... i had that problem yesterday. Now im struggling to upload the rom.
by wrong command also, it creates the nb1 file. so do DIR and see that .nb1 with 0 bytes will be there. delete it and try again!
enJoY

BigStorage without SD-USB reader...

Hi all,
i hope this hasn't been asked before. I'd like applying my magician the bigstorage hack but i've not a USB SD card reader. I could buy one, sure, but i'd prefer to save my (sadly very few) bucks.
That's what i thought:
Solution A: is it possible to use the magician itself as a card reader using Softick Card Export II? Would ntrw work the same? Is there the possibility to damage the magician/sd card???
Solution B: is it possible to run a hexadecimal editor from the magician so to edit the rom image directly on the phone without the PC?
Solution B seems difficult to me since the magician should be able to handle a 64MB or more file, and i think its 64MB ram size wouldn't be enough.
Solution A, instead, seems practical but i have the concern to damage my beloved (the magician!). I'd like to know your opinion before trying.
Bye and thanks you all,
this forum rulez!
Isidoro Russo
PS: Last question: do the ntrw reading/writing process destroy my sd card??? I think i've read something about this in a thread but can't remember which one.
I don't think it's going to work, don't know that program called softick card export, but you need to be in bootloader while you're doing it and then you can't run any programs. And I did the the bigstorage rom (with card reader) and it didn't destroy my SD-Card...
risidoro said:
Hi all,
i hope this hasn't been asked before. I'd like applying my magician the bigstorage hack but i've not a USB SD card reader. I could buy one, sure, but i'd prefer to save my (sadly very few) bucks.
That's what i thought:
Solution A: is it possible to use the magician itself as a card reader using Softick Card Export II? Would ntrw work the same? Is there the possibility to damage the magician/sd card???
Solution B: is it possible to run a hexadecimal editor from the magician so to edit the rom image directly on the phone without the PC?
Solution B seems difficult to me since the magician should be able to handle a 64MB or more file, and i think its 64MB ram size wouldn't be enough.
Solution A, instead, seems practical but i have the concern to damage my beloved (the magician!). I'd like to know your opinion before trying.
Bye and thanks you all,
this forum rulez!
Isidoro Russo
PS: Last question: do the ntrw reading/writing process destroy my sd card??? I think i've read something about this in a thread but can't remember which one.
Click to expand...
Click to collapse
Both options are not feasable.
The first option is not possible since Softick Card Export II needs the OS to be running, and your device needs to be in the bootloader mode for the image to be flashed. The second option is not possible because your magician doesn't have enough RAM to load the file...
And using ntrw will not destroy your SD-card, but it will permanently delete the files on that card!
oh oh we zijn de melk vergeten.....
But what does ntrw itself do?
I just thought it was used to read out /write the romfiles.
I probably blundered upgrading my compact:
I read the page on a site where the whole procedure (which is the Word-file in the ftp's Backuptool folder) was explained. It stated that an SD card with at least 128 MB was needed for the whole procedure.
Since I had 132 mb left on mine I thought I could use that one, which was the one with my sprite backup file and games and sorts.
But the card remains unreadable for the Compact and XP. So must I really fotmat is or is the some workaround to retreive my stuff or delete whatever romupdate or ntrw did to my sd-card.
Sorry but i don't understand why solution A should not work.
I think it could go this way:
1) activate bootloader mode and run 'romupdate.exe' to create a copy of the installed rom in the sd card. The device's S.O. is still installed even if it's not usable while in bootloader mode.
2) soft reset the device. Now the phone should exit bootloader mode and be fully functional since we've only taken a copy of its ROM and not deleted it. The device will work as usual and we can run Card ExportII
3) use Card Export II on the device and ntrw on the pc to copy the dumped ROM from the card to the pc.
4) modify the rom on the PC
5) copy the modified ROM back to the sd card using ntrw and Card Export.
6) follow the final steps required for the phone to install the rom on the sd card. Card ExportII is no more needed so it's not a problem if the phone must go to bootloader mode.
Summarizing: I need to run Card ExportII when the phone is still operative and not while it's on bootloader mode. The only step i'm not sure about is the first: i don't know if the romupdate.exe process leave the ROM on the device intact or delete it. If it remains intact (as i suspect) then is possible to soft-reset the device after the ROM dumping to run Card ExportII and copy the dumped rom to the PC.
What do u think about it? PLS, Let me know.
In case you're wondering why i don't just try myself instead of asking you, i can say that i'll try as soon as i'll have a new sd card (the one i'm using now has only 32MB). I ordered a 512MB card on ebay last friday so i'd receive it this week. I'll keep you informed on this topic.
Bye bye,
Isidoro
IT WORKED !!
Well if I’m not the first I must be close.
I can confirm your theory works beautifully 100%.
I followed my same procedure as normal found here http://forum.xda-developers.com/viewtopic.php?t=29266 but used card export and the Magician's SD Drive
I dumped my ROM straight into the Magician SD card drive.
Read the ROM from the Magician’s SD drive onto my PC.
I then successfully wrote the ROM back into the Magician SD drive.
Now for what ever reason I couldn’t get the Magician to Flash, it would not come up with the “Press Power to Flash……”
Now this could be for many reasons one of which is I just tried to write my original ROM back to the PDA which should of worked.
All I know is you can use the Magician CD Drive as your card reader to read/write your ROM info
Equipment needed
1 x Magician (Great PDA)
1 x SD Card (128Mb or larger)
1 x Card Export II program (I used the trial)
Plus all the other normal software needed to do Big Storage
PS I'm going to"Big Storage" my wifes MAgician tonight using this method so I'll let you know
UPDATE
Issue one,
Since you don't have a card reader you have to format the card after you dump your ROM onto it, if you don't, card export doesn't see the SD card in your Magician. To format the card inside your Magician from your PC you have to un-tick the Magician setting "Protect MBR" (what ever that stands for, & NO i haven't read the instruction, who ever does).
Issue 2 (this is a general rule for big storage)
Knowing if the write function has worked, I have witten to the SD card (inside the Magician) many time and sometimes it comes up with no error other times if states "The parameter is incorrect". To prove you have a workable file on the SD card after the write fuction of NTRW, when you remove and replace the SD card into the Magician it should ask you to reformat, if it doesn't then you have no file on the card.
IT WORKS 100%
I have dumped and flashed the Magician without a Card Reader.
Thanks for the great idea.[/b]
sure it works.
0) backup
1) dump rom
2) install cs2, now you get one more diskdrive
3) use WinHEX to open drive (F9) and select your SD (_physical_drive_)
4) now you can find and replace (twice!):
02 00 00 80 00 20 20 00 00
02 00 00 b8 01 20 20 00 00
5) bootloader mode and apply modifiedrom
ampda said:
Issue one,
Since you don't have a card reader you have to format the card after you dump your ROM onto it, if you don't, card export doesn't see the SD card in your Magician. To format the card inside your Magician from your PC you have to un-tick the Magician setting "Protect MBR" (what ever that stands for, & NO i haven't read the instruction, who ever does).
Click to expand...
Click to collapse
Ehem, can you pls explain better this point? When I have to format and where's the Protect MBR setting?
Anyway I'm happy my way worked!!! I won't have to buy a card reader!!!
Nitrogen said:
sure it works.
0) backup
1) dump rom
2) install cs2, now you get one more diskdrive
3) use WinHEX to open drive (F9) and select your SD (_physical_drive_)
4) now you can find and replace (twice!):
02 00 00 80 00 20 20 00 00
02 00 00 b8 01 20 20 00 00
5) bootloader mode and apply modifiedrom
Click to expand...
Click to collapse
Well, your method seems even better! You edit the rom directly on the card without using ntrw to read/write on the card. I guess CS2 (point 2) is card exportII?
Your method should work with card reader too in theory, so why so many people's still using ntrw? Does the file on the sd card (when romupdate ends) is the same of the one found on the pc after ntrw?
I hope that damn* sd card (i bought on ebay) won't take too much to arrive!!! :twisted:
Bye bye,
Isidoro
Even though I have no need for this solution, due to having a few card readers, I must applaud your ingenuity. Simple answers to complex problems is the sign of pure intelligence
IT WORKS!!! IT WORKS!!!
This morning I received the sd card i'd ordered on ebay, it's a 256MB SanDisk UltraII. BTW it's a lot slower than the 16MB MMC i was using before: 0,26 and 0,08 VS 0,72 and 0,43 of the MMC (numbers are the read and write speeds measured with pocket mechanic 1.60). Is there a reason for this? The bigger the card the slower? Or simply MMCs are speedier than SDs? What do u think about it?
Anyway lets talk about the bigstorage!
First i tried with my method (well i don't pretend to be the inventor, i say 'my' to avoid repeating all the steps).
All went as expected till the moment to ntrw write myrom.nb1 back to my sd card. I tried several times but without success. Everytime, after ten minutes, ntrw ended without any error but the sd card was empy and formatted (while there shouldn't have been any filesystem on it). Don't know how ampda did it but i gave up after 4 or 5 tries.
Then it was the moment to try out Nitrogen's way and, wow! it worked flawlessly!!!
Nitrogen's method not only does not require any sd card reader (that was my concern) but does not even require any ntrw operation!!!
This means that u can apply your bigstorage hack in less than 5 minutes (the time to romupdate the ROM on your sd card and edit it)!!! No card reader, no ntrw, no dos prompt, no delays, no risks to burn your card out.
It's absolutely great!!!
But it comes at a price, you need to buy WinHex (the demo version cannot save your changes). Card ExportII trial, on the contrary, can be used without problem (but i suggest to buy this wonderful program!).
Hey, now i'm a bigstorage owner too!
Bye bye
Well thats great news, glad it worked for you. I must admit it did take some doing to get the file on the SD card. I'll try the other method tonight on mine (I like to test things) and see how it goes. You shold of asked me about WinHEX before you bought it.
next step could be ppc program for patching thouse 4 bytes on SD without even connecting to standalone PC...
shamus said:
next step could be ppc program for patching thouse 4 bytes on SD without even connecting to standalone PC...
Click to expand...
Click to collapse
Actually i think it would be possible if a skilled ppc programmer made a program to change them! Who knows? Maybe in the future...
Bye bye,
Isidoro
Nitrogen
how can i read the nb1 file from sd if sd is no readable on windows???thanks
capellone85 said:
Nitrogen
how can i read the nb1 file from sd if sd is no readable on windows???thanks
Click to expand...
Click to collapse
I hope Nitrogen won't complain if i answer your question.
After the romupdate, the sd card won't contain any filesystem so, as u said, neither windows nor the magician will be able to read it.
Anyway, WinHex's F9 (and only it as far as i know) give you access to both logical drives (that is drives with a filesystem) and physical drive (direct access to the raw data even without filesystem).
You have to: connect your magician to windows with card export enabled, cancel Windows' request to format the removable unit (that's your sd card), open WinHex, press F9, select Removable Media under Physical_Drive tab. Et voilà! You'll have your nb1 rom backup available.
Just a drawback: the search function (to locate 02 00 00 80 00 20 20 etc hex string) will be very slow.
Summarizing: WinHex let you access raw data on an unformatted disk drive! Great!!!
Bye bye,
Isidoro
OMG..i got scared
Well i did it, and got scared, after the process had finished i got "Download Failed, Checksum Failed", ok i thougght, i will just reset and try again, so i reset and OUCH, it wouldn't load, just locked on the Qtek screen. then about 10-15 minutes later it loaded windows. I crapped myself. lol.
But i am now useing a BIGStorage, with 112, installed with NO SD Card! YAY
also if ya dont wanna buy WinHEX, then try FlexHex, its a 30 day trial and you can save without purchasing... Lots of goodness to be had by all.
Dahquim
@dahquim: All that happened to you because you're a lazy bastard too sluggard to read one of the thousands post carefully and thoroughly which mentions all your "findings" as being normal - some even give a decent explanation for them.
But whom am I telling this... you're not the one who's readings threads.
This method works perfectly with zero issues. The instructions were spot on - can't thank everyone enough. Funny that dahquim got so close but didn't even realize it. LOL.
guess i'll shut up then.....
dahquim
risidoro said:
capellone85 said:
Nitrogen
how can i read the nb1 file from sd if sd is no readable on windows???thanks
Click to expand...
Click to collapse
You have to: connect your magician to windows with card export enabled, cancel Windows' request to format the removable unit (that's your sd card), open WinHex, press F9, select Removable Media under Physical_Drive tab. Et voilà! You'll have your nb1 rom backup available.
Just a drawback: the search function (to locate 02 00 00 80 00 20 20 etc hex string) will be very slow.
Click to expand...
Click to collapse
Dear Isidoro
okay I did all till the search and I didn't find the string in the file, (02 00 00 80 00 20 20) also I have one more question, what should I substitute instead of that string?
sorry I'm new to these things in Jam.
Thanks for replying

Resize a ROM Image Made with 128 MB SD Cart

:?: Hello @ll,
can anyone tell me how i do resize an image .nb1 made with ntrw
from a 128 Mb Card an can i format the sd card in raw format usigng by the xda with a simple format program instand of romupdate.exe ?
A 64 Mb image is needet for my frinds on the other side of the world.
Have anyon a idee for my ?
Thanx,
xda.glawion.de,
You can cut the .nb1 at around 64MB. When you download eg. a BS rom, you can see where they end. It reads something like 'htce'. The rest can be skipped, viewing with a hexeditor ofcourse. But becarefull this 'htce' is on more places in the rom. Also mksbigstorager wcan perform this trick & will convert the rom to a BS one as well.
Maybe you can dump an image with ntrw via your magician with cardexport over the mbr, don't forget to uncheck 'protect mbr' I didn't manage though. Otherwise use romupdate as you said, after that the mbr is gone and you can write the newly .nb1 on it so a magician will see it.
Good luck, M
128Mb original backup ?
Yes.
128ROM copy 128ROM2
open 64ROM hacked, copy all hex to 128ROM, save.
open 128ROM2 original, copy 416 bytes to 128ROM, save.
128ROM ready to write Card 128Mb !

ntrw error

Hi all,
Now that my device is past its warranty period, I have decided to upgrade my O2 Mini as I want the blackberry software.
However, I am following the AM's excellent how to PDF but come to a grinding halt with an ntrw error.
C:\>ntrw write new.nb1 i:
Usage: ntrw file drive:
I get this error both when I'm trying to backup my old ROM as well as transferring the new ROM back to my SD card.
Any ideas?
I'm tipping it could be a card reader problem maybe?
Cheers,
Deva
Could be the wrong version of ntrw. Try one of the other versions cause you're syntax seems correct.
If you're using a laptop cardreader then that can be the reason too, always tricky when it's not working.
M
You were spot on oltp.
I downloaded Ver 2.0 and it worked a treat.
Thanks for your help.
Deva
New problem now....
I put the SD card with the BS ROM on it into my mini and put into Boot-loaded mode, but instead of bringing up the SD Download screen, it just goes to the standard 'Serial' Boot load screen.
I can't take a trick.
Again, any ideas?
Thanks,
Deva
- uncheck usb in Act.sync on your PC
- connect the magician with usb (screen reads USB now)
- start romupgrade on your pc ....
M
Thanks for your quick response oltp, but Im a little confused.
I've been following AM's PDF guide and it says after I have loaded Big Storage ROM to my SD card, just to put it into my mini and boot it into "Boot-loaded" mode. Is that not right?
Do I need run romupdate.exe instead?
Thanks for your help,
Deva
Sorry I misread your post: I thought you were still dumping…
I guess you must have formatted your SD somewhere in the process & now have a MBR again on the card. NTRW will write the image after the MBR & your magician can't find it cause the bootloader looks @ the first position, to solve your error you have to:
- put your magician in Bootloader (camera & power & soft-reset at the same time for a few seconds) wait till screen fades & reads 'serial v1.0x'. Screen is very dark since backlight is of.
- connect usb, now the screen reads 'usb v1.0x'
- start romupgrade on your pc
- pick the magician connection in the listbox, wces something I belief
- now a screen pops up
- type d2s in this screen
- follow progress on pc & magician
- wait till checksum finishes
- get SD from the magician & put it into a cardreader. DON'T FORMAT!!!
- type on commandline: ntrw write [your BS romimage name].nb1 [sd driveletter]:
error at the end is normal
- put the SD in your magician
- now it should read 'press power to flash'
- press the power button
- watch it reaches 100% - checksum will always fail
- reset & hopefully enjoy the new rom
& I hope you've done these steps as well:
- open your dumped rom.nb1 with the hexeditor & replace twice the usual BS byte pattern
or
- open your dumped rom.nb1 & the BIG Storage with the hexeditor and replace the first 416 Bytes of the BS rom with the first 416 bytes of your dumped rom.nb1 & save it to BSrom.nb1
- type on commandline: ntrw write BSrom.nb1 [sd driveletter]:
Cheers, M
Hi oltp,
Yeah, I did reformat in between dumping the ROM from the Magician onto the SD card and dumping the BSrom.nb1 back to the SD card.
I didn't realise that the SD card needs the dumped info from the magician as well as the modified nb1 file.
OK, I will redo the steps and see how I go.
Thanks for your help, really appreciate it mate.
Cheers,
Deva
PS. Yes I did use hex editor to copy the 416b from orig nb1 to BS nb1 file, but the SD card only had the new BSrom.nb1 file on it & nothing else when I put it back into the phone. No wonder nothing happened (d'oh). Thanks for your patience
Hi oltp,
I have reviewed ampda's PDF "how to" and it does say to format the SD card before you ntrw write the new nb1 file back onto the SD card. Is this right?
That mean there is only one file on the SD card, the new BSROM.nb1. Is thats all thats needed to flash the ROM?
Sorry to be a pain but I have followed the PDF guide without success.
Thanks,
Deva
format
Hi Deva,
The pdf is incorrect @ that point. The technical explanation is this:
Romupgrade dumps your rom right @ the first bit of your SD, destroying the MBR of the card. NTRW reads the whole card with the read & saves an image to your hard-disk. When you format your card a new MBR is created & NTRW will write the new image after the MBR. Without a MBR NTRW will write @ the first position of the card, like romupgrade.
Apperently the bootloader reads the first bytes of an inserted card & as it reads magician it will accept it as an rom-image. If the bootloader finds an MBR it just doesn't give you the 'press power to flash option'.
So dump your rom on your SD & write your BS image without format on the same SD.
BTW I think a format doesn't wipe your card, only the fat. On a hard-disk it works like that anyway.
Regards, M

Sd card problem on Magician

Hi Bro,
I need some advice on O2 mini as my SD card is not working good.
Before I started my Rom experiment, the SD was working good with both the magician and my laptop.
I made a mistake and I did not backup my rom before I start flashing.
After changing to my new rom, seems like I cant inter-use the SD between my laptop and magician. The magician cant read anything from the SD if I put data into the SD from my laptop via SD card reader/writer. When inserted to the magician, it will prompt to reformat. The same thing happen when I slot in the card to card reader after writing something from magician.
Therefore, now, I cant use SD to update rom ect.
How can i solve this problem? Thanks
Russ
Have you already tried formatting the SD card? When an SD card is used for ROM upgrading the card becomes totally unreadable for both PC and Magician.
Zerimar,
I did reformat of the SD on my laptop before writing the image to the SD via ntrw.
However, after slotting back to Magician, then go to Bootloader mode and wait for the "start loading prompt" but that have not happen yet.
russ
I think I misunderstood you, sorry. Put the Magician into bootloader mode first then insert the SD card. It should then display the message asking you to press the Power Switch to start the upload.
Thanks for your reply dude,
I've tried that too. It does not look promising.
I hope there is nothing wrong with my sd slot in the magician and i dun think there is any hardware problem. I confirmed that the Image was written in the SD.
Initially the SD card was working well with the magician before i did any rom flashing myself. even with the 1.12 WWE rom i cant read the SD. I've tried to reformat using XP on my laptop, and put back to magician. Then the magician will prompt to format again. else i cant see the storage card in the file explorer.
I've tried:
1) Slot in SD and wait - DUN WORK
2)Slot in SD, disable Async USB, and slot in use to Magician and wait. -DUN WORL ALSO
3)Slot in SD, press camera, on/of, and reset and wait till the SD load screen- ALSO DUN WORK.
4)Go to Boot loader, the slot in SD and wait- ALSO DUN WORK
5) No more idea
I wonder if different rom version will not work with certain sd brand.
My details is : 1.12 WWE with big storage.
SD : Kingston 256MB
I've tried with 1.13 WWE also but the same problem.
Hope someone can help or anyone have the same problem before?
Hello, Try this one
I think if you get problem with the SD card, you can use Mr. OLTP ways.
First open this :
http://wiki.xda-developers.com/index.php?pagename=MagicianRomUpgrade
then
downloadls all the tools you need, from the site.
1. Unzip NL_11300_131_11200.exe (or any other shipped-rom) to get all the .nbf & enterbl.exe . click right your mouse and chose extract to NL_11300_131_11200\
then you must copy all the file from NL_11300_131_11200 folder to c:
ex: c:\temp (make a new folder "temp", and copy the file from the NL_11300_131_11200 folder).
2. Put NBFDEC in the same directory = open nbfdec folder, you will find release folder in there, open the relase folder and copy 2 file to c:\temp.
3. open the temp folder and find getdevicedata.exe, Copy the getdevicedata.exe to your Magician and execute it (it will not provide any gui displays or feedback whatsoever), open the windows in my device(in your PDA), search for getdevicedata.txt. then copy to your desktop, and open with notepad.
4. To decode nk.nbf -> nk.nb1 start a command window, go to the directory where you stored nbfdec & the other files & type: nbfdec -d nk.nbf nk.nb1
this isi the ex:
in cmd
c:\documents and settings\frans>cd c:
c:\documents and settings\frans
c:\documents and settings\frans>cd ..
c:\documents and settings>cd ..
c:\>cd c:temp
c:\temp>nbfdec -d nk.nbf nk.nb1
this will convert nk.nbf to nk.nb1
don't close the CMD windows
now open the Hexeditor (must use the newest version V3.x)
open file/nk.nb1
then klik replace button , in the upper insert 02 00 00 80 00 20
in the lower 02 00 00 b8 01 20
replace all, enter.
save file in same name.
then back to the CMD window
c:\temp>nbfdec -e nk.nb1 nk.nbf
and
close the CMD windows.
open the temp folder, plug your PDA to USB,
On your PDA press power,camera and reset to bootloader mode.
clik maupgradeut_noid.exe on the temp folder.
and follow the instruction. if shows error 120. repeat again clik maupgradeut_noid.exe this will start to instal your OS
FINISH
thanks to MR. AMPDA, MR. OLTP and Mr. SEAN
for helping me.
Pls follow the guides on the board a little more carefully! Mine is very good ;-)
When you dumped your rom image on your SD with your magician, you completely destroyed the MBR of the SD. Before you save the image to your laptop with ntrw, your laptop will want to format it, cause it can't unserstand the car
. Don't do that. just put it in your cardreader & back it up with ntrw. Then you can write back another image to the card with ntrw & put your card in your magician. Just as long as you didn't format the card in between the operations the bootloader will recognize the image on the SD by the word magician which must be the first thing it reads on the card. If there's a mbr instead of the word magician, no mather what the bootloader will not present you the image 'press power to flash'
Hope you understand know how to solve your 'problem'
M
Hello yeoruss,
did u actually fixed the problem with using the sdcard on notebook and ppc at the same time? Ive the same problem after storing my ROM on SD.
I simply cant use the card in both units. When i format it under windows, is works in Windows but not on PPC - The PPC asks to reformat the card to make it readable.
When I format the Card on PPC, it works there, but no more in Windows.
Im experimenting all the time but i cant see the solution
Edit: I did not changed the ROM on my Magician, i just tryd to backup my current ROM.
Thank u

Categories

Resources