I got my Fuze about 2 weeks ago. Been trying to flash to rom since day one. I started off with parallels, was detected and everything, but when I would run HardSPL, the connection would time out at the point where it was about to send the files, and boot the device in bootloader mode.
I have now partitioned my macbook, installed Windoze XP Pro Sp2 onto bootcamp.
Here is the problem:
I run HardSPL, all goes well until the application attempts to put the device into bootloader mode. The application never detects the device, and just times out stating error [260] Connection
If anyone has a solution of sort for this, i would really appreciate it.
Thanks in advance!
Solved: Ran the manual SSPL provided, and it successfully connected after about 3 minutes.
Related
I'm sure this has come up a billion times, but I couldn't find it in my searches.
I recently put Faria's Kitchen ROM on my wizard. However, I accidentally put too many files on it and got the whitescreen problem. After figuring out what caused the whitescreen, I attempted to flash the wizard again, but found that activesync could not see the device. This is both with the whitescreen up and in bootloader mode. I am on XP (also have Vista, but I know that is a pain) using activesync 4.5.0. Any help is appreciated!
TIA
NuttySquirrel
Also, the computer can see the device, as it loads the drivers for it.
NuttySquirrel said:
I'm sure this has come up a billion times, but I couldn't find it in my searches.
I recently put Faria's Kitchen ROM on my wizard. However, I accidentally put too many files on it and got the whitescreen problem. After figuring out what caused the whitescreen, I attempted to flash the wizard again, but found that activesync could not see the device. This is both with the whitescreen up and in bootloader mode. I am on XP (also have Vista, but I know that is a pain) using activesync 4.5.0. Any help is appreciated!
TIA
NuttySquirrel
Click to expand...
Click to collapse
well, when you have the phone in bootloader mode (holding voice key on bootup) activesync is still not going to see the phone. but you should be able to flash the thing... probably back to tmo 2.26 just to be safe...
When I attempt to flash the device (using a variety of different roms) the tool either gives me error 264/274 (Connection) or 300 (Wrong Update Utility).
Hello all. I have followed the instructions to get wm6 and got stuck on step 9 of Karhoe's guide. Activesync will no longer see my device. so i cannot move forward. my phone is stuck on bootloader screen. After 'resetting device' in terapro. i saw the splash screen on my device then it went immediately to the bootloader color bars. everything else showed exactly what was on Karhoe pics. i just need activesync to see my device so i can proceed. any suggestions please. Thank you very much.
Activesyn will not see your device as it has been wiped clean of windows. Since you will need to be in booloader screen to install wm6, it doesn't matter if your activesyn sees your phone or not.
I ran into the same issue, i had to actually disable the 'allow usb...' option in activesyn so the romupdater utility can see the phone. So try it both ways.
enable it as suggested and just run the next step of installing the wm6gsmupdate...if you get some message saying connection error, then disable it and try again.
no activesync. Error [264]: Connection
thanks for the reply flashhsalf. it has not worked out for me tho. i tried both ways several times. enable/disable usb. i get same ERROR [264]: Connection.
im going to try it with a different laptop.thanks again.
Once I have this error too. Just reboot my PC and format BINFS one more time and all became fine. Don't know that is the reason, but this trick was helpfull
Have You re-enabled "Allow USB connection" @ connection options in Your Activesync??
got it to work...!!!
thanks all. i tried what was suggested all day...then when i went home i tried again with no success. to the point where my battery just died. i thought it was a paper weight at that point. but i decided to plug into the charger and the bootloader came up again. this time without the USB indication in the lower left corner. after a 2hr charge i took it to the same laptop which i rebooted. enabled usb then it worked! strange but glad i got it to work. Thanks again folks!
i updated to 6.1 but im experiencing issues with internet. ERROR
the remote party has ended this connection. this is the case with MMS as well. anyone experience this?
xdabe said:
Hello all. I have followed the instructions to get wm6 and got stuck on step 9 of Karhoe's guide. Activesync will no longer see my device. so i cannot move forward. my phone is stuck on bootloader screen. After 'resetting device' in terapro. i saw the splash screen on my device then it went immediately to the bootloader color bars. everything else showed exactly what was on Karhoe pics. i just need activesync to see my device so i can proceed. any suggestions please. Thank you very much.
Click to expand...
Click to collapse
i am also stuck to the same point ..
please help me what to do , why does this happens ..
i am very nervous ...as i cant make it a paperweight...
please help ..
thanks
my device is IMATE SP5M
and i have correctly done steps upto 8...
and when i try to do step 9 i only get three color boot loader screen
my device is super CID
info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x7820000 Bytes
HTCSSuperCID ' HTCE
Xdabe if you actualise Radio ROM, before upgrading to WM6.1 you wouldn't notice that problem with an Internet.
Try upgrading Radio ROM for your device.
Gsmsikar once you are in bootloader, and have SuperCID, just start installing Radio ROM first, then OS.
I finally got connect between my HTC Touch Pro and OSX (parallels + Activesync)
I am trying to run RaphaelHardSPL-Unsigned_190_1_3 and everything goes well, but when it trys to connect to the device to start the mod, i get Error [202] Connection. I have tried enabling/disabling Advaned Network Funtionality in Connection settings, but that did not help. I have tried manually going into bootloader (when the transfer is about to start, I hold VolDown, and reset, and wait for Bootloader to go into USB mode). That didn't work for me.
My question(s) are, how can I get the HardSPL running, or how can I get my deviced flashed in general (SD method didn't work)
AND: My version in HARDSPL is stated to be 1.95.502.5. Is it OK if I downgrade to 1.90.1.3 in order to allow custom ROMs?
Thanks in advance.
Parallels doesn't play nice with the USB bridge.
Try boot-camp (works for me).
I crashed my first Kaiser, flashing with Parallels. Couldn't recover it after the usb connection cut out mid flash. I sent it in for warranty exchange, telling them it crashed while doing an " official " rom update. luckily no one looked too close and they sent me a replacement.
Now I only use Bootcamp and xp. And after more flashes than I can count, I have never had a problem.
Hello guys
last week my Tytn II decide to also get stuck at the bootscreen. It had been running more than a year with one of Dutty's ROMs without any problems at all. Fortunately I knew this forum so I didn't really panic but started reading possible solutions to the problem.
Flashing new OS or SPL via USB didn't work. Nor was I able to connect via mtty to give the boot command. I finally got it back working by flashing KAISDIAG.NBH and after that flashing RUU-356-patch-nostuckinSPL-FORCEUSB as KAISIMG.NBH both via the SD method. After that I have downloaded and flashed the latest standard HTC rom & radio. The device boots and can make calls.
However whenever it is connected to a pc it just freezes. Or at least becomes so slow there's nothing that can be done with it. Activesync connection cannot be established. Note, this does not happen if the device is connected to my car charger or to another USB charger, but only when connected to a PC, XP or vista, doesn't matter.
I've tried flashing different boot loaders, OSes & radios, so far no luck. Currently OS = 3.34.721.2 WWE & Radio i= 1.65.24.36.
Booting & making calls works, connecting via activsync doesn't.
I'd appreciate it if anyone could give me some tips as to what could be the cause of this problem.
Anyone got any ideas as to what I could do?
dear all,
first at all: I´m completely new here, so hello.
I finished reading the Wiki twice, also the guide from 'mskip' (Flashing your First GSM Raphael Rom (For Noobs)). very good and sounds very easy.
now I downloaded this file: RaphaelHardSPL-Unsigned_190_1_3
when I´m trying to flash, it results in a "error 202: connection". could the windows mobile device manager be a reason, because here is just an explanation with activesync. as I use win7 64bit, activesync will not run.
I also checked lots of posts here, but did not get a right answer which could lead to a solution.
btw I have the "MDA Vario IV"-version.
greetings, tris
EDIT:
Update: Now I downloaded "TAEL ROM v6.28244 RC2".
Connected mobile to PC, waited until it is connected via 'windows mobile device manager'.
Proceeded with the update (my image is 1.69.111.6) until the screen turned black and a progress bar is shown (0%). now error 262 appeared. have to unplug USB cable, reinstall battery and restart. old system is still working. what am I doing wrong? btw, same error on my laptop with win7 32bit with fresh installed 'windows mobile device manager'.
EDIT2: okay, and same on my other laptop with winXP and activesync.
You need to flash hard spl before doing anything else. Try putting the phone into bootloader (hold volume down, then soft reset), then connect it to your PC once it's in the tricolor screen and run the hard spl exe.
After that, just flash roms off your sd card. Make sure it's FAT 32 format, rename the ruu_signed.nbh to RAPHIMG.nbh, put it on the sd card root, and then go into bootloader and follow the instructions.
volume down and reset done. phone switched to tricolor screen. then I started 'RaphaelHardSPL-Unsigned_190_1_3', phone switched to gey screen with progress bar. 30 seconds later after 0% progress: error 262 appeared
EDIT: also when trying to update via bootloader, my image (1.69.111.6) will be left blank, I can´t see the version number which is currently installed.
I just hope you have a GSM TP/RAPH...
RAPH300 -> "T-Mobile MDA Vario IV"
but why do you ask? do I have the wrong software?
Just hear of those bad incidents with CDMA phones and GSM ROMs is all...
What does it display on the bottom of the screen when you boot into the tricolor screen/bootloader before you connect it to your PC and then after?
first serial, later USB
oh my god! *facepalm* okay for all the noobs out there: look at your phone. if you use HardSPL for the first time, you have a short timeframe to confirm "unsigned access to bootloader" via touchscreen. if you don´t do so, you will result in connection error 202 / 262.
thank you all, it works