Hi there,
I bought a Qtek S200 and I tried to do a ROM upgrade. I followed the instructions given in the website http://kimpeacocke.blogspot.com/2006/06/how-to-perform-rom-upgrade-on-your-i.html
I got the upgrade from this site at ftp://xda:[email protected]_022021_Dopod_PDAMobizEdition_v101.zip
I followed the procedure given in the website given above. After I upgraded successfully the phone has become locked in the boot loader screen. I have done both soft reset and hard reset. Nothing works. The phone gets locked in the boot loader screen. Need help.
Thanks,
Julian
Try to reflash with Qtek ROM instead...
Why you said that it's locked on the Bootloader screen?
Is it frozen or locked?
Hi Rayan,
I tried flashing with the Qtek ROM. I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there. Nothing else happens. I have sent the device back to the guy from whom I bought it.
I got the same problem as Julian - I tried to upgrade with the mentioned ROM and now my device are stucked at the boot screen :?
Some help here ? I'm in same situation
I have an O2 with Dopod rom, after I instaled some software I must to restart and then my O2 are stucked/frozen on Windows Mobile splash screen
Only if I remove the battery I can stop the pda.
I can't do nothing to make him to start. Some ideea ?
:shock:
Later Edit :
solved with http://forum.xda-developers.com/viewtopic.php?t=49298&sid=35f5c1e9e165997b4634ea0c7700ac76
Same issue here with a O2 Xda Neo with German Rom.
Applied the procedure of the prophet wiki : How to CID unlock and Upgrade your Prophet (SPL 2.09 & 2.15)
After step 6 and a soft rest it is stuck in bootloader and will not do anything else, not even off or hard reset...battey has to be removed in order to shut it off....
Any ideas?
Remind me to find the guy who wrote the wiki page on unlocking CID in Prophet......good job pal......
Aaaaarggghhhh %^*^%*^%*^%*
Problem solved..
Hi everyone,
Good news at last. I sent my Qtek S200 to the guy from whom I bought the phone. He fixed it and now I am a happy man. You can check with him if everything else fails. Email him at E gadget Depot ( [email protected]).
All the best..
i tried to upgrade my QTEK S200 with this RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip it got to 95% and then it gives me nbf file cannot work with your PDA. Please help.
I have this problem too, i know only one exit from this situation - i have flash my s200 with RUU_215737_2157135_023021_QTEK_s200_RUS ROM, now it work fine.
you find it her
bootloader issue
I have the same problem too, If anybody know method to fix this problem please help us.
I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there.
THX in advance for you help
Robert
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Please, the links to the solution does not exists anymore.
I need help!!
Qtek S200 stuck in tri-color screen, all flashing so far still does not make it work..
When doing a hard reset I get format failed.
/Jonas
I have same problem!
Anyone can help?
TJSM said:
I have same problem!
Anyone can help?
Click to expand...
Click to collapse
Go to HMA4's upgrade guide or my thread in my signature...
same problem
i have exactly same problem and i couldnt solve it too.So can someone help us?
Please someone explain completely what should we do.
i can not active sync and waiting on the bootloader screen
bacardilima said:
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Click to expand...
Click to collapse
daelee,
you can get normal state, follow the bolded attention at above quote.after entering the 3 colour screen connect USB and you can load the original WM5 ROM on your device. after that, upgrade to any wm6 by the rules and active sync.
the link is dead on that message..
i went to the that page and the link for solution is dead.
http://forum.xda-developers.com/showthread.php?t=376561
find out is there anything that can help!
i madd up date for my pocket prophet imate jamin with ver
RUU_Prophet_220734_2207114_024721_NVID.exe
RUU_Prophet_220734_2207114_024721(AKU2.3)_lvsw_edition_PS8Mb.exe
but when i made restart i got spalsh screen and pocket hange .
i can not solve this problem can u hlp me .
eltabry said:
i madd up date for my pocket prophet imate jamin with ver
RUU_Prophet_220734_2207114_024721_NVID.exe
RUU_Prophet_220734_2207114_024721(AKU2.3)_lvsw_edition_PS8Mb.exe
but when i made restart i got spalsh screen and pocket hange .
i can not solve this problem can u hlp me .
Click to expand...
Click to collapse
1. dowenload this latest i-mate official rom from here
2. enter your jamin into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the jamin to your pc (make sure your battery is fully charged)
4. run the i-mate official rom.
5. good luck!
SAME PROBLEM with JAMin
I've tried this rom but I received this massage.
"ERROR[296]: UPGRADE ONLY"
IPL 1.00
SPL 2.20.0001
hello I briqué my qtek s200 after having wanted to pass from fantastic V1.0 to the version 2.0ac2 how I can repair this problem when I light my ppc there remains blocked on page QTEK keep the world in one I is necessary a fast solution in advance for me THANK YOU
just go bootloader mode then flash again.
qtek s200 is not dead
hello I wanted right statement that I found how to repair my qtek S200 it was enough to return in the bootloader while pressing on the button power and the photo button to be able in trer in the bootloader and thus to restore a connection usb with the PC and the qtek thank you louse to have to help me has to solve this problem however simple has to solve I hope to help of other people in the same situation only me with the pleasure
Hi everyone,
My qtek s200 dont boot, i just try hardreset, update rom in bootloader but nothing result..
Qtek stays in operator logo
IPL 2.10.0001
SPL 2.10.0001
GSM 02.69.21
OS 4.0.0.0
This happens because i was trying update rom to os 4.0.0.4 and there was a error during de instalation.
Then i try connecting again with activesync 4.5 but there was no conection.
now the qtek dont boot to operating system
Help me please.....
downgrade to wm5,upgrade to wm6,everything should work fine.
wich file?
how can i downgrade to wm5 without activesync?
by bootloader?
Wich file and where i find?
Thanks for your help!!
finally i ugprade to prophet 2.20.7.34 and my s200 is alive again...
Thanks....
How? Same problem here
same problem
i have tried again again end again, and now it's ok
note :
at the end of step 1, when s200 said "tap on screen" -> i have taped
after i have start step 2 as indicated in the tutorial
Good afternoon,
first you must conect pu s200 in bootloader mode (press camera button and make reset with your sylus pen- screen must appear three colors) then plug usb cable, then run the upgrade/downgrade rom
In the end the qtek reboot, install de apps and you must make software reset
Bye
Ratzumen
I have the same problem here. I had the wm6 rom on my qtek s200, but my headset worked not fine with it. So i tried to downgrade to the aku 3 rom for my s200. It seems ok. But when i turned the pda on, id didn't go further that the qtek boot screen. I also could not get to the bootloader screen to update another rom. What can i do?
Hi guys,
My Imate SP5 is stuck at the first screen where the IMATE logo (clubimate.com) comes up and then it does proceed any further ....and after about a minute it becomes blank.
I tried to do a hard reset but even that ended up in the blue screen .
I got it into the bootloader mode and tried to load a fresh rom . However the tera term pro says that it cannot open the device.
I am stuck at this point and cant proceed further ...
Please help
Farhan
Did you disable USB in Active Sync?