Flashing Issue - Tilt, TyTN II, MDA Vario III Windows Mobile ROM De

Hi,
Trying to Flash Hard SPL 3.56 to my T-mobile based tytn II. Everytime i go through the process (using Jump SPL) it fails at 0% with Error [262] Update Error.
Can anyone give me any pointers on where i might be going wrong? I am using Windows XP (first tried with a Vista laptop which had the same problem despite downgrading drivers to try to resolve).
As far as I can tell i've been following the guide properly.....
Thanks very much
Jason

Do you have .net installed in your machine?

jasonfrancis170 said:
Hi,
Trying to Flash Hard SPL 3.56 to my T-mobile based tytn II. Everytime i go through the process (using Jump SPL) it fails at 0% with Error [262] Update Error.
Can anyone give me any pointers on where i might be going wrong? I am using Windows XP (first tried with a Vista laptop which had the same problem despite downgrading drivers to try to resolve).
As far as I can tell i've been following the guide properly.....
Thanks very much
Jason
Click to expand...
Click to collapse
ask your question here http://forum.xda-developers.com/showthread.php?t=433835 and please don't start new threads

msd24200 said:
ask your question here http://forum.xda-developers.com/showthread.php?t=433835 and please don't start new threads
Click to expand...
Click to collapse
You read my head.......
Held back from posting earlier as didn't to be the first post of doom...
Mods please close.

Over/Under on posts before lock! 8

Apologies
Sorry about that everyone! I'll post in the right place now.
Jason

Related

What i am doing wrong?

hi,
i wanted to upgrade rom to 2006-10-05_Upgrade ROM_AKU2.3_lvsw, but when i start UPGRADE_ROM.bat it writes me ˝the system cannot execute the specified program˝.... i have g4
What i am doing wrong, please help me.
Thank you
Are there any instructions how to upgrade this rom, or any other?
tnx
Can you find more information on XDA-Wiki. You have to follow the ten steps the guys from PDAMobiz mentioned.
do i need to unlock CID?
Yes first you follow the ten steps, finally you can be able to put the ROM version you wish.
SPEEEED said:
hi,
i wanted to upgrade rom to 2006-10-05_Upgrade ROM_AKU2.3_lvsw, but when i start UPGRADE_ROM.bat it writes me ˝the system cannot execute the specified program˝.... i have g4
What i am doing wrong, please help me.
Thank you
Click to expand...
Click to collapse
Just a doof ball question. Are your running the update from your PC or your SD Card?
i am running from update from PC, is this ok? Where can i find instructions for unlockin cid? On wiki are't for 2.15.0001
I tried to unlock cid with this instructions http://en.pdamobiz.com/en/forum/PDAforum_posts.asp?TID=437&PN=1 ,but when i done first proces my phone stop at dopod screen.
Please help me because i would realy like to upgrade it to lvsw edition...
thank you
also he said you must downgrade to a specific rom first and listed the link.
read the post fully and you should be ok
i downgraded to RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID, read all thread...
allways the same
problem is with my computer. On other computer was everething fine. Somebody knows why?
thank you anyway...
Try upgrading/re-installing active sync to 4.1 or higher
i have allready 4.5
SPEEEED said:
i have allready 4.5
Click to expand...
Click to collapse
thats a BETA version, try 4.2

Issues with upgrading to WM6 - solved + tips

Hi guys
I know this has been asked a million times before, but trust me, I've tried following the tutorials posted her but with no luck.
So here goes:
I've tried flashing this ROM:
http://rapidshare.com/files/24185105/ruu_vario_aku3.3_3822_382120_026911_tmo_de_ger_ship.zip
via awizard but it stopped so I've unplugged it, got it into bootloader mode and flashed with the xplore WM6 ROM but it just hangs at the boot up screen after restarting.
G3 device
IPL 3.08
SP 3.08
GS 0.269.11
OS 3.8.2.2
Any ideas?
sav_za said:
Hi guys
I know this has been asked a million times before, but trust me, I've tried following the tutorials posted her but with no luck.
So here goes:
I've tried flashing this ROM:
http://rapidshare.com/files/24185105/ruu_vario_aku3.3_3822_382120_026911_tmo_de_ger_ship.zip
via awizard but it stopped so I've unplugged it, got it into bootloader mode and flashed with the xplore WM6 ROM but it just hangs at the boot up screen after restarting.
G3 device
IPL 3.08
SP 3.08
GS 0.269.11
OS 3.8.2.2
Any ideas?
Click to expand...
Click to collapse
Was your wizard CID unlocked ?
I see that you have OS 3.8.2.2 , that is not my OS. It should have been 10.2.0.8.
That means your wizard might have been locked.
Very strange.
I did run CID-unlock first. It was running xplore before I tried flashing the tmobile rom, so maybe the images didn't get flashed.
Anything I can do to fix it?
Okay, I'm busy trying to flash the wizard_love rom. Been sitting at 96% for a while lets hope it goes further.
Okay, the upgrade went through. OS2.26
XDS-dev tutorials and the love rom for the win! Now I can relax again...
Will flash to WM6 soon.
sav_za said:
Okay, the upgrade went through. OS2.26
XDS-dev tutorials and the love rom for the win! Now I can relax again...
Will flash to WM6 soon.
Click to expand...
Click to collapse
Heh. So now that you have found the tutorials helpful, perhaps you'd consider changing the thread title?
--M
Sorry about that, have changed it.
For some reason I can't get it back to WM6 but will try again and keep you guys posted. Device is definitely CID unlocked, but for some reason it keeps hanging at the boot screen.
OKay, assuming my wizard got CID-locked for some reason, how do I downgrade to ver1 to unlock it again?
I've downloaded button's ver1.05 rom. Can I just install it, or will it give me an error saying I need a newer ROM?
Sorry for all the questions, I just don't want to take any chances.
sav_za said:
OKay, assuming my wizard got CID-locked for some reason, how do I downgrade to ver1 to unlock it again?
I've downloaded button's ver1.05 rom. Can I just install it, or will it give me an error saying I need a newer ROM?
Sorry for all the questions, I just don't want to take any chances.
Click to expand...
Click to collapse
Luke....use the Force... Follow the steps in the tutorial link (in my sig.) but the short answer is "yes".
--M
Hehe, thanks I've done that. Will try tomorrow, thanks.
I feel like a bit of a plonker asking so many questions with such obvious answers.
Okay, after a LOT of trial & error I've finally gotten it back to WM6. Here's what I did:
1)Downgraded to IPL/SPL 1.01 using button's ROM
2)CID unlocked using lokiwiz
3)Upgraded to mr_clean AKU2.3
4)Upgraded to Faria's WM6
I didn't use aWizard as usual, just the rom upgrade utilities that came with these ROMS.
Hope this helps anyone that's struggling with the same problems I've been having.
Thanks for the tutorials, they've been a great help. The only part that didn't work for me was upgrading to T-mobile's 2.26 because it would freeze on the bootup screen after upgrading to WM6. Replace that step with mr_clean 2.3 and it works fine.
hey how did you get your wizard_love rom to get past 96% without crashing? mine just gives me error 302, which is  ERROR [302~318] : UPDATE ERROR
any clue? thanks
mapleman321 said:
hey how did you get your wizard_love rom to get past 96% without crashing? mine just gives me error 302, which is ? ERROR [302~318] : UPDATE ERROR
any clue? thanks
Click to expand...
Click to collapse
Hi
I got the phone into bootloader mode then it worked fine. It got stuck at 94% iirc but I just left it until it finished.
Hope this helps

Impossible to install the HardSPL on my Tilt!!!

Hello to all,
I'm new on this forum and let me thank everyone !!!
I've an AT&T Tilt 8925.
First of all I tried both the ways suggested in the threads to install the hardSPL but I've always the same problem:
I've no problem to install on my device the JumpSPL1.56-KAIS.exe (or the 1.93) but when I launch the KaiserCustomRUU.exe I follow the instructions on my pc and after the program has detected my rom version (1.57) and
has started the installation of the HardSPL (at least it seems) the activesync connection disappears (it becames grey) and the RUU shows an "error" and suggests me how to restore my device leaving the battery etc. (but to restore everything it's enough a just soft reset)
Please can you help me???
Alf
Please post in the appropriate thread.
??? Which thread ???
I'm really sorry....which thread is the correct one ?
Thanks
msgrx78 said:
I'm really sorry....which thread is the correct one ?
Thanks
Click to expand...
Click to collapse
No need to apologize. The one in which you got the hardspl files.
Okay, I'm gonna answer this because it's buried in the HardSPL thread & hard to find since it was answered once about a month ago by me. Diconnect your device, do NOT reset. Run thru the recovery or close out the HardSPL flash.(You are using Flash HardSPL w/ the RUU, right?) Reconnect your device & run the utility again.
If this doesn't work it's because I'm partially guessing. You've not provided nearly enough information. I need to know what SPL version your device currently has, also if you are running a firewall & which one, also if you use any McCafee products.

Help for reverting back to origianl rom! Urgent!!!

first of all sorry for y English...
Ive been read the threads about that, but ive this problem:
i ve a hardspl 3.29 and trying to downgrade to original rom the flashing process stops at 15%.
i can install only custom rom and so i cant reverting back to original rom and spl.
ive been tried to flash first the spl but not working...
someone can help me please?
thx!!
wow, I don't think I've ever haleard it this way before. Usually you can't upgrade to a cooked ROM, not the other way around.
So, you get no errors while installing a cooked ROM, but it stops at 15% when trying to downgrade...
I know that some shipped ROMs flash the SPL at 15%, so this must be the problem.
Undortunately, I am a lucky one who has never had anything bad happen to me while flashing (besides my laptop running out of battery), so I don't really have much advice to give you, but I'm sure somebody else will.
Sorry, hope it all goes well for you
HardSPL prevents itself from being replaced. You need to run JumpSPL or SSPL-KAIS on the phone when it is running WM as normal, which will switch you to triciolor screen, where you can flash the original SPL.
This should be detailed in the "How to revert to factory state" page in the wiki.
thx but ive been done all and now my kaiser it's brick on bootloader:
dont allow to flash hard spl
dont allow to flash custom rom
dont allow to flsh original rom
Help PLease!!!!!!!
tried with mtty but nothing...USB PORT CAN NOT OPEN
Try that sticky thread? http://forum.xda-developers.com/showthread.php?t=423486
kilrah said:
Try that sticky thread? http://forum.xda-developers.com/showthread.php?t=423486
Click to expand...
Click to collapse
tried but no chance...
my suggestion is to search this forum for "stuck in bootloader"
you're sure to find something there
mbarvian said:
my suggestion is to search this forum for "stuck in bootloader"
you're sure to find something there
Click to expand...
Click to collapse
now...
solved the stuck problem on bootloaderwith mtty for Vista, but with hardspl it's impossible to flash an original rom on the device (flsh stops at 15% error 226-flash error- wath is?)
so...i want to flash an original rom: waht can i do? help needed please...thx!!!
always prpblem in falshing original update...flashing process stops at 15%. ive downgraded at wm6 with spl 3.07.
ERROR 226

Please Help Me With the Bootloading screen?

I followed all of the steps to flash a new ROM into my tilt. I attempted to install a hard SPL 1.93, but it stuck me at the bootloading screen. I can't active sync because im at the screen and it wont let me. I tried the program mtty, but i cant get it to work because it wont register. it says...:
KAIS1*0
SPL-1.93.0000
CPLD-8
I know i'll probably get banned from the forums, but I'm just hoping someone can give me a quick answer. I appreciate the help.
never heard of that HardSPL, only 3 versions.
Go grab a proper HardSPL (I recommend 3.29) and see if you can flash that, but you should properly study first.
Also, please read the Flashing For Noobs section and DO NOT MAKE NEW THREADS FOR COMMON PROBLEMS
XPhamz said:
I followed all of the steps to flash a new ROM into my tilt. I attempted to install a hard SPL 1.93, but it stuck me at the bootloading screen. I can't active sync because im at the screen and it wont let me. I tried the program mtty, but i cant get it to work because it wont register. it says...:
KAIS1*0
SPL-1.93.0000
CPLD-8
I know i'll probably get banned from the forums, but I'm just hoping someone can give me a quick answer. I appreciate the help.
Click to expand...
Click to collapse
He has a white screen issue. His factory spl is 1.93.0000. Also its not hard spl 1.93.0000 its jump spl 1.93.0000
Go here:
http://forum.xda-developers.com/showthread.php?t=354061
And here
http://forum.xda-developers.com/showthread.php?t=423486&highlight=white+screen
I hope that this works.
Thanks for the responses, but I can't connect my phone to my computer due to active sync not recognizing onto my phone. I installed it and reinstalled it twice. I read everything on the Bootloading screen, but half the programs wouldn't load up. I can't upload anything to my SD card because i don't have a reader.
XPhamz said:
Thanks for the responses, but I can't connect my phone to my computer due to active sync not recognizing onto my phone. I installed it and reinstalled it twice. I read everything on the Bootloading screen, but half the programs wouldn't load up. I can't upload anything to my SD card because i don't have a reader.
Click to expand...
Click to collapse
ok try this just plug your phone up to the usb cable and flash a stock rom. Dont worry about the sync your phone wont sync to your pc when in bootloader. Only a stock rom DONT flash a custom rom. After you flash the stock rom you should be able to start over. I hope that this helps
sorry to sound like a newb but how would I go about doing that? I have it downloaded.. and I ran it on my computer? now what?
XPhamz said:
sorry to sound like a newb but how would I go about doing that? I have it downloaded.. and I ran it on my computer? now what?
Click to expand...
Click to collapse
What installing the stock rom? Yes it has to be run from your pc. I think that you need to read this thread Also
http://forum.xda-developers.com/showthread.php?t=433835
http://forum.xda-developers.com/showthread.php?t=374691
Kaiser Wiki
http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser
Vol22002 said:
What installing the stock rom? Yes it has to be run from your pc. I think that you need to read this thread Also
http://forum.xda-developers.com/showthread.php?t=433835
http://forum.xda-developers.com/showthread.php?t=374691
Kaiser Wiki
http://wiki.xda-developers.com/index.php?pagename=HTC_Kaiser
Click to expand...
Click to collapse
It worked! I really do appreciate your help! After hours of hoping I didn't brick my phone! Thank you so much.
No problem I remember what it felt like to be new at this. Good luck with your rom upgrades.
Mods please close this thread. Thanks

Categories

Resources