i am really stuck here after i upgraded my o2 xda exec to ur rom. it took too much battery and took me ages to charge it. however, this is never the issue. what happened was that my phone went off battery and couldnt make it charge or even connected to the pc.
it actually charges when i plug but without the orange light which indecates that it is charging.
Plus whenever i try to connect it to pc it says uknown device. even when i switch to bootloader mode it still says unknown device. therfore i cant flash a new rom. the battery is new and the device is O2 Xda exec but is also as new.
pls pls anyone, sort me out.
Moe
Mo0oe said:
i am really stuck here after i upgraded my o2 xda exec to ur rom. it took too much battery and took me ages to charge it. however, this is never the issue. what happened was that my phone went off battery and couldnt make it charge or even connected to the pc.
it actually charges when i plug but without the orange light which indecates that it is charging.
Plus whenever i try to connect it to pc it says uknown device. even when i switch to bootloader mode it still says unknown device. therfore i cant flash a new rom. the battery is new and the device is O2 Xda exec but is also as new.
pls pls anyone, sort me out.
Moe
Click to expand...
Click to collapse
Welcome to the forum
I would recommend to follow this instructions on the Wiki: http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Charge your battery at 100%
And don´t forget to vote!
Good luck,
I had similar experience with this ROM even after installing everything successful, and good use of ROM for about 7-10 days, not sure why and thought am the only one experienced this. The phone simply went off (i remember using it the previous day night to check mails). No display, it wont indicate wehther it charging, hard reset or softreset does not do anything etc etc
I have put the Uni in Bootloader mode, did a DOC format and flashed the ROM again, it worked and working so far.
Remove SIM and SD Card from Uni and it should recognise the Uni when connected to PC. Its better to use a XP machine as Vista need a separate proces which you can find in this forum by searching.
Please Read wiki and proceed as appropriate to your device condition. The detail on how to do DOC format is in there in wiki
All the best
stilll stuck with my uni!!!
rbalu72 said:
I had similar experience with this ROM even after installing everything successful, and good use of ROM for about 7-10 days, not sure why and thought am the only one experienced this. The phone simply went off (i remember using it the previous day night to check mails). No display, it wont indicate wehther it charging, hard reset or softreset does not do anything etc etc
I have put the Uni in Bootloader mode, did a DOC format and flashed the ROM again, it worked and working so far.
Remove SIM and SD Card from Uni and it should recognise the Uni when connected to PC. Its better to use a XP machine as Vista need a separate proces which you can find in this forum by searching.
Please Read wiki and proceed as appropriate to your device condition. The detail on how to do DOC format is in there in wiki
All the best
Click to expand...
Click to collapse
orb3000 said:
Welcome to the forum
I would recommend to follow this instructions on the Wiki: http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Charge your battery at 100%
And don´t forget to vote!
Good luck,
Click to expand...
Click to collapse
thanks to u both lads for replying but unfortunately i am still stuck. i tried all the ways u told me abt and tried wiki. Apparently, so many ppls have the same problem but no clear way for the solution yet. both of my computers cant recognise it!!!
i really need ur help stilll in this and u can help me step by step through msn messenger if this is convenient to any of u guys.
rbalu72 said:
I had similar experience with this ROM even after installing everything successful, and good use of ROM for about 7-10 days, not sure why and thought am the only one experienced this. The phone simply went off (i remember using it the previous day night to check mails). No display, it wont indicate wehther it charging, hard reset or softreset does not do anything etc etc
I have put the Uni in Bootloader mode, did a DOC format and flashed the ROM again, it worked and working so far.
Remove SIM and SD Card from Uni and it should recognise the Uni when connected to PC. Its better to use a XP machine as Vista need a separate proces which you can find in this forum by searching.
Please Read wiki and proceed as appropriate to your device condition. The detail on how to do DOC format is in there in wiki
All the best
Click to expand...
Click to collapse
how do i do the DOC format. i searched everywhere pretty much but couldnt figure out how to do it!!
pls let me know. cheers!!!
Mo0oe said:
how do i do the DOC format. i searched everywhere pretty much but couldnt figure out how to do it!!
pls let me know. cheers!!!
Click to expand...
Click to collapse
hi
1.) first you need to download mtty utility, here is the link http://forum.xda-developers.com/download.php?id=9864
2.) on PC go to activesync and uncheck "allow USB connections"
3.) Then go into bootloader mode (light button+power button and soft reset)
4.) On PC open mtty utility / software.
5.) On PC select USB from the "port" drop-down on the upper left corner of the dialog box and hit OK.
6.) On PC you see a blank white screen. Press enter to get "USB>"
7.) On PC type "set 14 0" and hit enter. You will see some gibberish on the mtty utility which will again be suffixed by "USB>"
8.)the type in "task 28 55aa" (try not to copy/paste this because mtty sometimes doesn't recognise it if it is pasted)
9.) you will se WAIT, so wait until it is finished
10.) unplug the usb cable, and re-plug it into the same port
now you are still in bootloader mode, now flash the new ROM, remove the
usb cable and do a hard reset
I hope i could help
damir-bosna said:
hi
1.) first you need to download mtty utility, here is the link http://forum.xda-developers.com/download.php?id=9864
2.) on PC go to activesync and uncheck "allow USB connections"
3.) Then go into bootloader mode (light button+power button and soft reset)
4.) On PC open mtty utility / software.
5.) On PC select USB from the "port" drop-down on the upper left corner of the dialog box and hit OK.
6.) On PC you see a blank white screen. Press enter to get "USB>"
7.) On PC type "set 14 0" and hit enter. You will see some gibberish on the mtty utility which will again be suffixed by "USB>"
8.)the type in "task 28 55aa" (try not to copy/paste this because mtty sometimes doesn't recognise it if it is pasted)
9.) you will se WAIT, so wait until it is finished
10.) unplug the usb cable, and re-plug it into the same port
now you are still in bootloader mode, now flash the new ROM, remove the
usb cable and do a hard reset
I hope i could help
Click to expand...
Click to collapse
hey,
thanks man. i got my uni back on track now. u r the best. thanks to everybody here. i am loving this forum.
thanks again,
moe
Related
Hello,
Today i bought the kaiser and wanted to rom flash it to 6.1
My plan is to flash it to L26KDTLB6 (http://forum.xda-developers.com/showthread.php?p=2574491&posted=1#post2574491) i've followed the instructions here : http://forum.xda-developers.com/showpost.php?p=2261226&postcount=2
and the flash was in progress but cancelled after 14% due to communication problems (????)... now when i resettred my kaiser i see this weird red green blue and white screen.
I am terribly worried i might have ruined my kaiser even before really using it.
I am begging you for help.. i would appreciate any kind of help from you guys.
Thank you so much
MIke.
Wow! Sounds like you are in deep doodoo. I had almost an identical problem last night trying to flash ROMeOS 4.7. I went and read the stickies at the top of this forum and was back up running in no time.
loserp3 said:
Hello,
Today i bought the kaiser and wanted to rom flash it to 6.1
My plan is to flash it to L26KDTLB6 (http://forum.xda-developers.com/showthread.php?p=2574491&posted=1#post2574491) i've followed the instructions here : http://forum.xda-developers.com/showpost.php?p=2261226&postcount=2
and the flash was in progress but cancelled after 14% due to communication problems (????)... now when i resettred my kaiser i see this weird red green blue and white screen.
I am terribly worried i might have ruined my kaiser even before really using it.
I am begging you for help.. i would appreciate any kind of help from you guys.
Thank you so much
MIke.
Click to expand...
Click to collapse
Sounds like you did not HardSPL. The tri color screen you are seeing is called bootloader. It's not as scary as it might seem at first. When you connect yoru device to your computer does it still show the letters "USB" at the bottom? If so, try flashing the stock rom for your device and see if that will fix your problem. After that be sure to make sure you've properly hardspl'd your device before flashing anything else.
loserp3 said:
... i see this weird red green blue and white screen...
MIke.
Click to expand...
Click to collapse
HOW COME YOU KNOW HOW TO WRITE BUT YOU CAN'T READ?
geez...
I had the same problem once. I remember I solved it that I first flashed it back to the OEM that came with it, and then flashed it again. It worked. Hard SPL and CID unlocker helped being that the phone was locked.
If you dont have OEM OS you can always find one here, just use the Search button.
Secondly, you have to follow the steps exactly as instructed because those are the only way to successful flashing. Are you sure that you didnt overlook one of the steps?
Pay special attentiton to the 2nd Q&A and also other Q&A being that there are all the answers.
Happy flashing mate.
Hello all,
I was able to revert back to hTC'S 6.1 rom...So everything was back to normal.
The thing is, i really want to make the kaiser look good with the d3d driver and the touchflo 3d, I'll give the http://forum.xda-developers.com/show...=1#post2574491 rom one more shot this time ill use
SSPL-KAIS.exe (is that ok ?? will that prep my device for rom flashing ??? )
is there another cooked rom that has the touch flo 3d and the d3d drivers ???
appreciate your help
MIke.
loserp3 said:
Hello all,
I was able to revert back to hTC'S 6.1 rom...So everything was back to normal.
The thing is, i really want to make the kaiser look good with the d3d driver and the touchflo 3d, I'll give the http://forum.xda-developers.com/show...=1#post2574491 rom one more shot this time ill use
SSPL-KAIS.exe (is that ok ?? will that prep my device for rom flashing ??? )
is there another cooked rom that has the touch flo 3d and the d3d drivers ???
appreciate your help
MIke.
Click to expand...
Click to collapse
Do NOT flash another rom until you have hard spl'd your device. Make sure you check out the thread at the top of this forum, which you already sited once. You should also consider sim/security unlocking your device as well. You can ONLY use jumpspl to put hardspl on your device. Absolutely do not start flashing roms until you can enter bootloader and next to spl: see "hard spl" somewhere in the title.
Hi
Ok, here's what i've done to prepare the device
1) i ran kaiser-HardSPL.exe and loaded the nbh that came with it
2) I copied SSPL-KAIS.exe to the kaiser and ran it
thats it... i didn't however see hard spl in the title.. i did see JUMPspl though
loserp3 said:
Hi
Ok, here's what i've done to prepare the device
1) i ran kaiser-HardSPL.exe and loaded the nbh that came with it
2) I copied SSPL-KAIS.exe to the kaiser and ran it
thats it... i didn't however see hard spl in the title.. i did see JUMPspl though
Click to expand...
Click to collapse
you are so making this too hard on yourself. Follow these directions to the letter and you'll be fine:
How to Install 3.2x.Hard SPL:
1. Plug the device into your PC
2. Copy Jump/Soft to your device. use JumpSPL If you have the "White Screen" issue, if you don't, you can use SSPL-KAIS.exe.
3. Take out your SD card & SIM Card.
4. Run Jump/Soft SPL on your device
5. Wait for the bootloader screen to appear and "USB" to show.
6. Right-click activesync, go into connection settings and ensure Allow USB Connections is unchecked
7. Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
8. Run KaiserCustomRUU.exe and flash the SPL
If you have problems with the above process, try this:
1a. download the attached files
1b. pull out the battery and reinsert it (this step *is* important)
1c. connect your PC to phone with a USB cable
2. REMOVE SIM and SD CARDS !!
3. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
4. after a few seconds "USB" appears on the phone display
5. unplug and replug the usb cable
6. deselect "Allow USB connections" in Activesync connection settings
7. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)
Notes:
With the JumpSPL you should *not* flash radio roms, OS roms or full roms. The JumpSPL is only needed to flash a HardSPL (or SPL)
the link to the thread in which this came from is here:
http://forum.xda-developers.com/showthread.php?t=396922
Having just redone this this morning to revert back to 3.29, I can confirm that it works.
In the future, please don't start a thread for this type of porblem. We all starte out by reading. I've been a part of this forum for 3 years and learned all I have from just reading and asking questions that could not otherwise be answered.
loserp3 said:
Hi
Ok, here's what i've done to prepare the device
1) i ran kaiser-HardSPL.exe and loaded the nbh that came with it
2) I copied SSPL-KAIS.exe to the kaiser and ran it
thats it... i didn't however see hard spl in the title.. i did see JUMPspl though
Click to expand...
Click to collapse
you did not read the instructions correctly. Try reading them again.
It says:
How to Install 3.2x.Hard SPL:
1. Plug the device into your PC
2. Copy Jump/Soft to your device. use JumpSPL If you have the "White Screen" issue, if you don't, you can use SSPL-KAIS.exe.
3. Take out your SD card & SIM Card.
4. Run Jump/Soft SPL on your device
5. Wait for the bootloader screen to appear and "USB" to show.
6. Right-click activesync, go into connection settings and ensure Allow USB Connections is unchecked
7. Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
8. Run KaiserCustomRUU.exe and flash the SPL
You are stopping at step 5. Perform steps 6, 7, & 8. After that time you can soft reset the device while holding down the camera button (that will take you to the tri colored bootloader screen) and it will say "hardspl" if you have done it correctly.
If you don't read more closely you WILL break your phone and nobody here will be able to help you. These procedures are easy enough to follow if you take your time and read. I only say this to save you a great deal of frustration when your phone dies later.
Also, remember in the future that all the information you are seeking is readily available if you look for it. Dont' expect someone to GIVE you the answer, and please please please....post your questions in a thread that is already around rather than starting a new one!
@ Scothua
like the way you think . . .
scotchua,
Thank you for your assistance. i've finally upgraded my rom.
thank you all.
Dear all:
Been an avid XDA reader, I decided it was time for me to test one of these wonderful ROMs. I finally settled with the ROSE.
Then I started looking for the instructions on how to do this. I am following THESE, and then THESE instructions.
Instructions are pretty clear, but I run into a bit of an issue when following them.
Let me describe what I do:
1. Hard resetted the phone (I undestarnd is better to perform this with factory settings), verified I have 100% battery.
2. With the AS enabled, ran SDA_ApplicationUnLock.exe - Got confirmation
3. Ran uspl_116_jockyw.bat - Everything goes as expected (follow the on screen steps, got the Tux on the screen, screen goes off with backlight on, no leds, and the phone gets disconnected from the PC)
At this point, I am supossed to be able to run the FLASH.EXE app, but my phone does something strange: I can hear a USB device being connected to my PC (from the Windows sound), but AS does not connect to the device (it stays gray and says "Not Connected"), therefore, I am unable to follow the flash procedure.
If I unplug my phone and restart it (by removing the battery), the phone boots properly.
I have been searching this behaviour on the forum without success. Maybe someone has seen this and is able to provide any assistance.
Please leave comments or questions. Any feedback would be appreciated!
http://forum.xda-developers.com/showthread.php?t=510470
i have the same problem, strange?
Dude when u r running this file uspl_116_jockyw.bat a message will appear on ur vox screen just see to it that u press yes on ur vox..... then do the procedure as it is.........
good luck
hi when you reset the phone did you go into settings\connections\USB to PC
and UNtick the Enable advanced network?
hhs6789 said:
Dude when u r running this file uspl_116_jockyw.bat a message will appear on ur vox screen just see to it that u press yes on ur vox..... then do the procedure as it is.........
good luck
Click to expand...
Click to collapse
Thanks, but as I state on my description on point 3, I can follow that part of the procedure, is after that the problem appears.
deuse said:
hi when you reset the phone did you go into settings\connections\USB to PC
and UNtick the Enable advanced network?
Click to expand...
Click to collapse
Thanks! That did the trick. Unfortunately, I am getting the known Error at 3%. I see at the bottom of the instructions that you might get it, and that "Instructions are below". I have been trying to find some info on the forums, but I got a little confused. Do I need a software to flash the SPL?
Thanks hhs6789 and deuse for taking the time to answer!
Read this http://forum.xda-developers.com/showthread.php?t=330909
go down to were is says EDIT and follow the guild.
also you will need to run the application unlock first.
hope it works for you
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
I think you have been bricked your device...
dineshkumaar said:
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
if it's not recognized, remove the SIM card, the SD card, and on the PC open activesync and disable usb connections. for more info open this link
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
what if the device is bricked
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
dineshkumaar said:
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
Click to expand...
Click to collapse
you have to find another rom and try to flash it to your PDA.
ARE YOU RUNNING windows XP on your PC?
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
dineshkumaar said:
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
Click to expand...
Click to collapse
have you tried to upgrade another ROM, and if you did, is your PDA now working?
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
dineshkumaar said:
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
Click to expand...
Click to collapse
Have you read here?
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Try to reflash with another ROM
Hope it helped
And don´t forget to vote!
I had already done those steps to get no results.
its my badluck.
If you cannot get into bootloader and you have done the steps above, then you cannot flash to another rom.......it would seem you now have a paperweight im afraid
I am still not able to revive my device. I know that it is just due to corrupt bootloader but don't know how to repair it.
If anybody ever has solution for this... kindly let me know.
Regards
Have you tested mtty?
I would recommend to PM a chef on Universal forum
Good luck,
Mtty is not detecting my device
it says can't open usb port
One More thing I have noted is that when I keep the device connected with the pc, at a certain interval of about 10-15 mintues my device's Led shows RED Light for few seconds and then turns off followed by the the "USB device not recognized" on my pc.
I hope this can be used as a hint towards reviving my device.
Regards
have you followed orbs advise above and pm a chef on that section, they maybe able to help. From my knowledge (limited on that device) i ddont think there is any recovery proceedure that you have not tried. Have u downloaded offical wm5 rom and tried it. I know and appreciate that it will probably not work due to corrupt bootloader, but what else is there to do??
To understand more, what did you do PRIOR to trying to flash to 6.5.
Did you hardspl correctly? Had you already flashed to another rom and just felt like flashing to another new rom?? Give us more detail.
Thanks for your reply
I dont know how to PM Chef.
I had used 3 other Rom versions of WM6.1 on my device. They ran very much fine on my device. But When i found WM6.5 xplode, I wished to try that too. But the rom update procedure went successfully till 99% and after that it showed an error that upgrade was not successfull. I pulled out the device and tried to restart if by all methods but I wasnt able to power on at all.
Thanks
Regards
ok, goto the thread that you got the rom off, click the chefs name and you will get a menu there to send pm, do it, he might have seen a similar problem or know how to correct bootloader.
good luck
noup really no...
Is bricked
my bro has bricked an Universal and the same led turns red no power off no bootloar no power it means the flash chip is dead!
Sorry to heard that.
He waits too long for the upgrade it tooks at least 40 minutes
then ERROR... but you know... the batt was died in middle process ( th batt was ****ed up, it say full charged but no! it was on 60 or 50%) then the stupid thing is make a hardreset.. i told him dont hR your device... justa simple reste and reinit the process... and huh! its bricked.
if you are interested on sell your parts
maybe my bro want some parts.
my advice(similar to other people):
1. Charge your batery somehow (in other device or anything else)
2. put your devce in bootloader mode and connect it to pc - it wll be detected like microsoft usb sync
3. use mtty try difrend versions becuse sometimes 1.42 does not detect it properly - read here for what to do with mtty
IMO this may be battery problem or nand chip problem - in both cases it is hardware fail
My Dear Samaritans,
IMPORTANT:
- My SD/Memory card is removed
- My Sim card is removed
I was upgrading to Tomal v8.9 on a vista 64 system via a virtual machine XP SP2. Update failed and I got stuck in bootloader.
Tried reflashing but got an error and the flash failed... also the program crashed during recovery.
Tried using v8.71 still crashed without any luck.
Moved to a pure XP SP3 desktop...
When I connect the device to the computer(s) "Serial" changes to "USB" but XP sees it as an unrecognized device.
Tried flashing again but same error as on the virtual machine.
Tried mtty (1.16 & 1.42) but neither give me the option of USB, only COM1 and COM2. And had already de-activated the USB connection in Activesync.
Have read through the forum but have had no luck. Everyone's issue is resolved as soon as they remove their SD or SIM, but I have neither and am also using XP with activesync's USB disabled.
Tried UNI_ExitBootloader but that does not find/recognise the device either.
If it helps -- My device is/was an O2 XDA Exec (Stock) which I had previously flashed with Tomal's v8.5
I am ready to try anything, please help!
P.S: The error is Error 112
Did you install ActiveSync on xp pc?
If not, do it now and try again.
I had similar problem. Had corrupted DOC sector
and MTTY was the only solution, but although the Serial changed to USB, I got 'unrecognised' message and Mtty didn't give USB as an option. At some point it occured to me that it was my computer's USB port, for some reason the device was recognised by 1 in 4 ports only, So I just tried my USB cable in different ports until the 'device unrecognised' messaged stopped appearing. Finally, after I was ready to cry in frustration, it just worked. Don't give up.
I heard it mentioned somewhere that the device that went through Mtty will be recognised only by the port used in Mtty procedure.
That... or your device's USB is no longer properly attached to the mainboard.
tomal said:
Did you install ActiveSync on xp pc?
If not, do it now and try again.
Click to expand...
Click to collapse
Already have activesync 4.5 installed with USB connection disabled...
Thank you so much for the prompt response and helpful thought!
enigma1nz said:
and MTTY was the only solution, but although the Serial changed to USB, I got 'unrecognised' message and Mtty didn't give USB as an option. At some point it occured to me that it was my computer's USB port, for some reason the device was recognised by 1 in 4 ports only, So I just tried my USB cable in different ports until the 'device unrecognised' messaged stopped appearing. Finally, after I was ready to cry in frustration, it just worked. Don't give up.
I heard it mentioned somewhere that the device that went through Mtty will be recognised only by the port used in Mtty procedure.
That... or your device's USB is no longer properly attached to the mainboard.
Click to expand...
Click to collapse
Thank you for the ray of hope! Will keep trying every hourly reboot in every USB port (4 in all).
Weird thing is I never had to go through mtty before so this is my first need for it.
Got the physical connection checked and it is supposedly OK...
Thank you for the prompt help...
Don't worry
I had exactly the same problem. First I tried this and it worked but still no connection via mtty. On that evening I disconnected and connected a lot and I removed the battery for a long time (one night). Later I could connect but I don't know why. Maybe these two things were the solution. Mtty showed "usb>" and I've done a DOC format...
If nothing works I would create a rom-image (on sunday or monday) for your sd-card like it's written in the service manual.
blingin said:
Thank you for the ray of hope! Will keep trying every hourly reboot in every USB port (4 in all).
Weird thing is I never had to go through mtty before so this is my first need for it.
Got the physical connection checked and it is supposedly OK...
Thank you for the prompt help...
Click to expand...
Click to collapse
No need for hourly reboots, just get into Bootloader, connect USB to your device and try different ports on computer with a few seconds in between to ensure no 'unrecognised device' message popping up. Once you'll get a connection - go for Mtty facility, the USB is the last on the list of ports.
330e said:
I had exactly the same problem. First I tried this and it worked but still no connection via mtty. On that evening I disconnected and connected a lot and I removed the battery for a long time (one night). Later I could connect but I don't know why. Maybe these two things were the solution. Mtty showed "usb>" and I've done a DOC format...
If nothing works I would create a rom-image (on sunday or monday) for your sd-card like it's written in the service manual.
Click to expand...
Click to collapse
There was no SD card when I began the initial flash but it still got stuck. Been trying without the SD and SIM but to no avail...
Thank you for the manual, downloading it now, will keep everyone posted in case anyone else is suffering from the same thing...
enigma1nz said:
No need for hourly reboots, just get into Bootloader, connect USB to your device and try different ports on computer with a few seconds in between to ensure no 'unrecognised device' message popping up. Once you'll get a connection - go for Mtty facility, the USB is the last on the list of ports.
Click to expand...
Click to collapse
Still trying, will keep you posted and thank you for the responses!
I think you understood me wrong. When your device is still unusable, I would create the files you need to do the steps in point 8.3 (Use Pre-loaded SD card to Re-flash Unit) in the service manual.
Sorry for my bad english
330e said:
I think you understood me wrong. When your device is still unusable, I would create the files you need to do the steps in point 8.3 (Use Pre-loaded SD card to Re-flash Unit) in the service manual.
Sorry for my bad english
Click to expand...
Click to collapse
It's the thought that counts not the language, thank you so much for your help!
I created succesfully a pre-loaded sd card, flashing via this sd works. But I can't copy the files. When I want to open the drive it says, that I have to format the sd card. Is there a special tool to copy the files? Or you find someone near you with a universal.
your need to format your SD after flashing.
330e said:
I created succesfully a pre-loaded sd card, flashing via this sd works. But I can't copy the files. When I want to open the drive it says, that I have to format the sd card. Is there a special tool to copy the files? Or you find someone near you with a universal.
Click to expand...
Click to collapse
tomal said:
your need to format your SD after flashing.
Click to expand...
Click to collapse
Tried the SD image method with a 128MB SD but didn't work. Maybe because I have a G4 and the method is for G3
managed to get a connection finally and ran MTTY, after "task28 55a" it just hung for a long time so I disconnected.
Tried running UNI_ExitBootloader.exe and now can get in and out of Bootloader but still cannot flash or connect...
Any suggestions welcome...
Try this....
This might sound silly but it's worked for me in the past.
1. Go into bootloader (without mem card or sim)
2. Plug-in the USB cable
3. Hold the buttons to go into bootloader again whilst plugged in.
4. DOC Format
5. Flash ROM
My Universal had loads of problems but that is how i fixed it, tried everything else like you, when i first plugged it in on the bootloader nothing happened until i pressed and held the buttons whilst it was plugged in, then windows made the usb connected sound so i quickly mtty'd! lol
Hope this helps, Good luck!!!
martinbrettphilo said:
This might sound silly but it's worked for me in the past.
1. Go into bootloader (without mem card or sim)
2. Plug-in the USB cable
3. Hold the buttons to go into bootloader again whilst plugged in.
4. DOC Format
5. Flash ROM
My Universal had loads of problems but that is how i fixed it, tried everything else like you, when i first plugged it in on the bootloader nothing happened until i pressed and held the buttons whilst it was plugged in, then windows made the usb connected sound so i quickly mtty'd! lol
Hope this helps, Good luck!!!
Click to expand...
Click to collapse
Thank you...
Xda2 stuck in bootloader screen after failed flash in vista
blingin said:
My Dear Samaritans,
Tried reflashing but got an error and the flash failed... also the program crashed during recovery.
When I connect the device to the computer(s) "Serial" changes to "USB" stuck within the bootloader screen
Tried mtty (1.16 & 1.42) but neither give me the option of USB, only COM1 and COM2. And had already de-activated the USB connection in Activesync.
Have read through the forum but have had no luck.
I am ready to try anything, please help!
P.S: The error is Error 112
Click to expand...
Click to collapse
Hi i have had similar problems also i have an XDA 2 pda originaly had wm2003 on it (tried to flash it to wm2003se ) can someone help me also im realy at a loss =C many thanks in advance (i will give more detail if someone actualy) replys to me
Wrong forum
Welcome to the forum
Universal does not means all devices, actually is a model
Please enter into the right section of the forum
Goos luck,
Can you Help?
I have an XDA II was on O2 uk network. I used to flash it all the time and knew my way around. however recently i flashed it in vista without thinking.. and as i upgraded the rom from wm2003 to wm2003se about 25% of the way through vista disconnected the device then it was unrecognised usb.. then vista started installing new drivers that recognised the device... however this then crashed flashing the rom onto the pda..
It wont soft or hard reset, i took the battery out for 24 hours and tried again and nothing.. the only thing on screen is that it says serial on the top of the screen (which changes to usb when connected but get error 101 when trying to reflash/ no activesync connection and am confused my mtty as when it does connect i cant type into the text area only paste)
on the bottom of the screen is v1.06 (which before the flash crash was V1.0 something lower than v1.06)
basicaly is the device recoverable as long as i have this serial / usb recognition by the device????? (using mtty i cant connect through ports or usb but thats because i dont seem to understand how to use it)
the other question is is there any other way to get a rom back onto the device without mtty or activesynch..
I pray that ysomeone will respond .. i miss my pda dearly
a thousand thanks in advance
Hello!
I killed my PDA-it. 3 Color does not load mode. With or without the battery I found some 3 types of drivers shown in the picture. Not associated with MTTY, absolutely dead. : (
I'd be happy if you share with me some trick for possible recovery.
Thank you!
How did you brick it??
Do a search for QC diag drivers or MotoQ drivers install them.And download mtty.When the driver is installed check which port the diag driver is installed on and connect mtty to that port,then type cego a the type task 8 (this should reboot it.
press n hold camera & soft reset button. tri colour screen wii appear
Is dead "MTTY" and I want 3 types of drivers. MTTY claim 3 colors mode. Not associated with PDA. I have another PDA operating "Cruise" which is associated with "MTTY" without a problem. Will try with this kind of drivers: "MotoQ drivers" will tell the result.
Thank you!
the hard reset procedure is holding gps and internet button pressed for 2 seconds and without releasing them stick your stylus into the soft reset hole.
keep those two buttons pressed until the grey screen appears then release them and press the green button for confirmation and the green button again after it's done to reboot
Try to remove the battery and cable, wait 1 minute, insert the battery and start the device with pressed camera button.
When the tricolor appears plug in the cable, wait for USB message on your device and flash.
Dark Dragon
I have similar issue.
have a polaris whcic i can not make HR
tried almost everything.
Has HTC original rom but is stucke at alignment screen.
Need to make HR.
Tried camera+reset makes soft reset
tried gps+explorer makes SR
I can acess it trhoug active sync, can it help to make HR?
rpsilva said:
I have similar issue.
have a polaris whcic i can not make HR
tried almost everything.
Has HTC original rom but is stucke at alignmen screen.
Need to make HR.
Tried camera+reset makes soft reset
tried gps+explorer makes SR
I can acess it trhoug active sync, can it help to make HR?
Click to expand...
Click to collapse
i think if you see the calibration/alignment screen...windows recognizes the phone and usb and you can reflash the rom
martinasa said:
Is dead "MTTY" and I want 3 types of drivers. MTTY claim 3 colors mode. Not associated with PDA. I have another PDA operating "Cruise" which is associated with "MTTY" without a problem. Will try with this kind of drivers: "MotoQ drivers" will tell the result.
Thank you!
Click to expand...
Click to collapse
i ave in the past a similar problem....mtty did not recognizes the phone and usb...the solution for me was to start the same on a older windows xp pc...
Hello again.
Phone not come in 3 color mode.
martinasa said:
Hello again.
Phone not come in 3 color mode.
Click to expand...
Click to collapse
also not with: press n hold camera & soft reset with stylus ..?
what it makes after you start the phone..'?
Ok I had the same problem. Now i can enter in 3 colors. Make this:
Step 1. Download and read this:
http://forum.xda-developers.com/showthread.php?t=393337
You need motorola Q drivers and a Windows XP 32bit to work.
Step 2. Read the post of jpg001 of this link:
http://forum.xda-developers.com/showthread.php?p=5515006
You need use the files of jpg001 to work
Step 3. You need a mtty called "mtty_0513_Test.exe" because other version freezes, at least for me. If you need more information i will be here. I'm trying to Hard-SPL my Polaris to work.
[email protected] said:
i think if you see the calibration/alignment screen...windows recognizes the phone and usb and you can reflash the rom
Click to expand...
Click to collapse
the problem is that I do not have hardspl installed yet.
have flashed with original rom but the problem remains.
The main issue is that at boot is stucked at "tap the screen..." and want to make HR to see if helps.
Tried to install Hardspl but always an error and stays at 0%
I am assuming hardware problem with touch screen....
If you can help...
rpsilva said:
the problem is that I do not have hardspl installed yet.
have flashed with original rom but the problem remains.
The main issue is that at boot is stucked at "tap the screen..." and want to make HR to see if helps.
Tried to install Hardspl but always an error and stays at 0%
I am assuming hardware problem with touch screen....
If you can help...
Click to expand...
Click to collapse
than i think you also must use mtty (reset the phone)....from post above or here:
http://forum.xda-developers.com/showthread.php?t=425922
the best is to use windows xp for that
luzbel_es said:
Ok I had the same problem. Now i can enter in 3 colors. Make this:
Step 1. Download and read this:
http://forum.xda-developers.com/showthread.php?t=393337
You need motorola Q drivers and a Windows XP 32bit to work.
Step 2. Read the post of jpg001 of this link:
http://forum.xda-developers.com/showthread.php?p=5515006
You need use the files of jpg001 to work
Step 3. You need a mtty called "mtty_0513_Test.exe" because other version freezes, at least for me. If you need more information i will be here. I'm trying to Hard-SPL my Polaris to work.
Click to expand...
Click to collapse
very interesting....very interesting
[email protected] said:
very interesting....very interesting
Click to expand...
Click to collapse
Thank. 1 long week reading posts...
Now I'm flashing Oficial rom and seems to work!! It will revive !!
Ok! It's finish and work!! My polaris back to life!!