Related
I read with most new ROM images that they should have problems with wifi connecting. I think this is a misunderstanding.
The universal can connect to 54mbit networks only at 11mbit speed. it can connect to WPA secured networks only with TKIP encryption.
Not with WPA2 or AES! i think a lot of people here make this mistake!
so please test this and confirm my findings
If I remember my WiFi networking, you can configure a fast network (54 or 108Mb/s) to allow slower devices or not to.
So it can depend on the network.
In theory, yes, you can connect an 11Mb/s device to a 54Mb/s network. Mine works like that.
a small correction
latest WM6 images fail to connect to hotspot with WPA (TKIP) secured. there is a small trick to bypass it (shutdown and start the device).
It work
So ... I have a D-Link 2100AP - up to 108Mb/sec. I connect with notebook at 54MB/sec. WPA-TKIP
With Universal, at 5-11MB/sec - everything is ok.
This is with JWright 2.02.02 ROM and radio 1.18.
But, for example, with Indra latest wm6 rom, don't work. I find the AP with signal Strenght of 81%, I select WPS-PSK, TKIP, provide the password, but nothing
I have 2 questions:
1. Internet over wifi doesn't work. I think wifi is working fine, becouse conmanager easiliy find my home AP and conect to AP.
But IE dosn't working at all over wifi,and over usb(activsync) IE working fine. Any solution??
2. Can i use activesync over wifi or join to my local network over wifi?
I have Qtek 8310
ROM: Greek WM6 ROM v5 by NiTroGen
OS: WM6 5.2.1616.18120 - Radio: 02.61.01 - SPL: 2.00.0014
budy wi-fi connection has some issues, that it gets connected with pc, or ppc, coz the connection settings are stored in router.. but as the connection remains down so IE wont work atall..and on wi-fi router u cant guess net connection is working or not.. check with ur net connection..
malhaar said:
.. check with ur net connection..
Click to expand...
Click to collapse
i think i don't understand u...
i can connect my laptop on my AP,
solution is maybe in aplicatio "Tornado Wi-Fi Settings "
siouxNS,
I had similar problem on XDA IQ. WIFI was connected to the AP, but IE was stuck in 'locating', and after some time (about 1 minute) error message appeared. I noticed, that when pinging my phone IP from laptop (also in my home network) few pings were ok (just after wifi connected to the AP), and rest of them timeouted. Sometimes, but very rarely, all ping responses were ok (I used ping -t on windows).
So, what I did to get wifi connection working:
1. started IE, when wifi is off
2. started wifi
3. shortly after wifi connected to my AP, I opened some internet page in IE (try to use one, that is not cached) - and it worked
And this works for me every time now.
Few more things:
- check that IE uses the same connection, to which wifi is assigned.
- you can use WLAN IP manager to manually set your IP, gateway and DNS servers
- my system is: windows mobile 6, OS 5.2.318, build 15341.0.0.1
hey guys,
I have the same problem. just flashed the new v3.6, can connect to the router, can even ping the mobile from my laptop via wlan, but still get the no connection error - from IE and opera.
what can I do?
EDIT:
finally got it. just had to change the type of internet from 'private/work' to 'internet'. thats it. stupid comment about vpn under it confused me...
fikol5 said:
siouxNS,
I had similar problem on XDA IQ. WIFI was connected to the AP, but IE was stuck in 'locating', and after some time (about 1 minute) error message appeared. I noticed, that when pinging my phone IP from laptop (also in my home network) few pings were ok (just after wifi connected to the AP), and rest of them timeouted. Sometimes, but very rarely, all ping responses were ok (I used ping -t on windows).
So, what I did to get wifi connection working:
1. started IE, when wifi is off
2. started wifi
3. shortly after wifi connected to my AP, I opened some internet page in IE (try to use one, that is not cached) - and it worked
And this works for me every time now.
I will try that
Few more things:
- check that IE uses the same connection, to which wifi is assigned.
its ok
- you can use WLAN IP manager to manually set your IP, gateway and DNS servers
Click to expand...
Click to collapse
whatkind manager u use? i use "tornado WI-FI settings"
on home network i use static IP's
adsl router, 192.168.1.1 (gateway)
wirelles AP 192.168.1.252
phone is connecting with 192.168.1.5 ,
can i use DHCP and DNS?
one more thing, when i go in some caffe with hotspot i don't have any problems with connecting and surfing.
My TouchPro can connect normally to unsecured wifi networks, but with WPA encrypted ones, it can only connect for the first time, after that it can not.
At home I have a wireless router/ADSL modem (Zoom X6) that is connected to my PC by cable, all my phones and laptops connect to internet via wifi. While other phones (1G iPhone) and laptops always connect successfully, the TP only connected once and then cannot or unable connect to the WPA security-enabled wireless network (although it's able to scan and detect the availability of the Wifi network). I tried to reset the router settings, even update router firmware, but no luck, it's still unable connect. I also tried with my office secured wifi network and I had the same problem.
Yesterday, I had to hardreset my TP and tried to connect once again, but problem was repeated, connected only once and after that, unable. Note that my previous PPC (TMobile Ameo WM5) didn't have any problem with the same wifi router and the same wifi settings (as follow).
My TP wifi settings:
Network Name: MyNetwork
Connects To: The Internet
Uncheck "This is a hidden network"
Next step:
Authentification: WPA-PSK
Data Encryption: TKIP
Greyed Out: The key is automatically provided
Network Key:************** (my pass)
Greyed Out: Key Index: 1
Next,
Checked "Use IEEE 802.1x network access control" but greyed (I can't change this)
Anybody know the solution for this issue?
Thanks and very appreciated for any help.
i experienced similar problems with my old p4350 but not yet with the TP...
no solution, sorry. but im quite unhappy that this issue still exists...
Any suggestion, pls.
yeah.. quite sucky.. I though the WiFi 'broke'.. but i was able to connect to a WEP site.. I think its something to do with WPA.
I never had this problem with my Diamond. The firmware on Diamond isso much more stable compared to Touch Pro..
I set everything to WEP and my key is open instead of shared, and now it works fine.
I had issues at my dad's, who has no encryption, and also there, when I set the key to open io shared, I got connection. (even though there is no key
anyway, it looks like that is the bug (at least in my device)
I have exactly same settings and same problem... but I want to use this encrypted connection since in future I will have to connect also in other places where I need it for sure.
Any help here?
I have similar promblem with my Hermes before.
My wireless router is running "Turbo-G" mode, my Hermes can't connect it with Turbo-G mode On.
After I change the wirless mode from Turbo-G to "g/b", my Hermes can connect it without any problem.
I tryed that and does not work...
strange is that is was working in the past and on router I did no changes but on TP I installed just some apps which should not affect this...
Only what could affect is Advanced config which I installed...
So where else can be problem?
How can I troubleshoot this?
Signal kvality is good but still keeps dropping and does not obtain IP from router.
mine works fine...not that that helps you in any way
I found the solution: set router to unsecured and use MAC filter. But that is only a tip, because my TP still can not connect with any other secured wifi.
I had same problem and looks like I found the bug in Advanced Config 3.2
There is in Network -> WPA auth... was enabled and I put Disabled (now I can use WPA auth anyway... before it just could not connect)
And next Wi-Fi delay after boot: 0 (when I changed to other number than I got problem that I could not even see any AP as I could see before and only network card settings was shown)
Try to play with other settings and you will see... I had also errors with device.exe after reboot... but now it all works as it should.
Just post here if it helps you also so we can notify creator of Advanced Config...
hung_ng said:
I found the solution: set router to unsecured and use MAC filter. But that is only a tip, because my TP still can not connect with any other secured wifi.
Click to expand...
Click to collapse
You are merely restricting people from connecting to your router.. without encryption, you are sending unsecure packets all over..
Have you tried using AES encryption on your device instead of TKIP? I only mention this because TKIP is the only one I haven't tried. All other methods of connectivity work fine for me with the TP.
I tried the PT using unsecured routers, WEP and WPA and all of them worked fine with stable connectivity.
The routers I have tried (without any problems) so far are:
1. Linksys WRT-54G running Tomato firmware
2. Linksys WRT-54G running DD-WRT firmware
3. D-Link DIR-655 running latest firmware
I tired open, WEP and WPA1+2 on all of the above routers and the TP responded with zero issues...
I am not using a custom ROM.
I hope this helps in some miniscule way.
Good luck.
Minus-1 said:
Have you tried using AES encryption on your device instead of TKIP? I only mention this because TKIP is the only one I haven't tried. All other methods of connectivity work fine for me with the TP.
....
I tired open, WEP and WPA1+2 on all of the above routers and the TP responded with zero issues....
Click to expand...
Click to collapse
I was about to say the same thing...
Not having any issues with my girlfriends WPA secured router. It's on WPA2-PSK and AES encryption. Enter key first time (case sensitive!!), and of you go... Connecting without trouble ever since
hmm..Funny mine still can't connect to my home WPA2, AES or TKIP.. I'm on the Buffalo Tomato firmware..
WIFI not connecting
This solution worked for me!! Excellent. This was a right pain!
thedino said:
I had same problem and looks like I found the bug in Advanced Config 3.2
There is in Network -> WPA auth... was enabled and I put Disabled (now I can use WPA auth anyway... before it just could not connect)
And next Wi-Fi delay after boot: 0 (when I changed to other number than I got problem that I could not even see any AP as I could see before and only network card settings was shown)
Try to play with other settings and you will see... I had also errors with device.exe after reboot... but now it all works as it should.
Just post here if it helps you also so we can notify creator of Advanced Config...
Click to expand...
Click to collapse
I've got the sollution, everybody on this forum probably has advance config installed, the program sets some default value's of it's own, set the WPA authentication under network in the advance config program to disabled and it will work again. Anyways, that worked for me
I've removed WiFi settings and then I edited settings again. It works now
Raphael Wifi problems
I bought this Fuze to replace my trusty Dash since I broke the antenna on my Dash. I'm running NRG Magic, but have tried other NATF and other ROMs as well, I cannot get this phone to connect to my wifi network I'm using WPA2-PSK but have disabled security for testing. My Dash and my laptop connect immediately with no problems. If I cannot get wifi going on this Fuze I'm afraid I'll have to put it on Ebay and try the Iphone, which people seem to love.
The Fuze did connect once, and it was WPA2-PSK at the time, I don't remember what ROM I was using at the time probably an NRG flavor, but Ihave had _no_ luck since.
Should I flash to 'official' ROM? Honestly I'm getting tired of playing with this thing I don't have the time.
Any help would be appreciated.
Thanks,
Marc
I may have found something
Check your time zone/daylight savings settings on your router. Phone and router time must be in sync.
hi, first post here.
i have an HTC Touch Cruise with the default factory rom and it has an internal wifi antenna... I'm trying to setup a wireless network with my neighbour but my PC doesn't have a wifi adapter (and i don't have the money for one right now), so i was wondering if it is possible to make the pda some sort of adapter for the pc to use via usb/bluetooth?
One of the first thing we'll do if it's possible is to crack the wep key cause he can't rembemer the password and a hard reset to the router doesn't erase it
can also anyone suggest some tools to do that job?
I was thinking of running these tools on the pc since the pda will only serve as some kind of NIC...
hope someone can help...
Edit: Forgot to mention that i also have a bluetooh adapter on the pc if that comes of any use
P.S: Great Forum btw
There's an internet sharing option in Windows Mobile 6. Connect to the wifi network using the cruise and configure the internet sharing options. Then connect the cruise to the PC via USB and the PC should be able to access the net via the cruise's wifi connection.
MeeMk said:
There's an internet sharing option in Windows Mobile 6. Connect to the wifi network using the cruise and configure the internet sharing options. Then connect the cruise to the PC via USB and the PC should be able to access the net via the cruise's wifi connection.
Click to expand...
Click to collapse
LOL Windows makes it easy for us!
MeeMk said:
There's an internet sharing option in Windows Mobile 6. Connect to the wifi network using the cruise and configure the internet sharing options. Then connect the cruise to the PC via USB and the PC should be able to access the net via the cruise's wifi connection.
Click to expand...
Click to collapse
i've been snoping around that part, but it asks me for a conection name in which is on <none> cause i don't have a connection configured... if i go to the connections part, i don't know what kind of connection to create as it asks me to create a VPN or an ISP connection...
how can i configure internet sharing propperly?
would i be able to crack the wep key on the pc that way? (cracking it on the pc via the pda)
1. The program you'ew looking for is WmWifiRouter 1.20, it enables you to use your phone as a WiFi -> USB adapter...
2. Ask your neigbour to use Cain on his pc... it can reveal what's written in the password boxes (if it's XP or older), reveal it in the WiFi connection settings on the pc... Whith this you won't need any WEP cracking... also he should be able to change the WEP key without the original... if he doesn't know the access code to the router that's THE problem, check the manual for default values, and try those first before attempting anything else...
3. For configuring a 3G/HSDPA/GPRS/EDGE connection you'll need a data plan from you mobile carrier... after that you can configure the connection on your PDA.
VPN stands for Virtual Private Networking (read Wiki for more info)
ISP stand for Internet Service Provider (this'll be the one you'll need)
gnick666 said:
1. The program you'ew looking for is WmWifiRouter 1.20, it enables you to use your phone as a WiFi -> USB adapter...
2. Ask your neigbour to use Cain on his pc... it can reveal what's written in the password boxes (if it's XP or older), reveal it in the WiFi connection settings on the pc... Whith this you won't need any WEP cracking... also he should be able to change the WEP key without the original... if he doesn't know the access code to the router that's THE problem, check the manual for default values, and try those first before attempting anything else...
3. For configuring a 3G/HSDPA/GPRS/EDGE connection you'll need a data plan from you mobile carrier... after that you can configure the connection on your PDA.
VPN stands for Virtual Private Networking (read Wiki for more info)
ISP stand for Internet Service Provider (this'll be the one you'll need)
Click to expand...
Click to collapse
From what i've read on this forums, WmWifiRouter is for routing my 3G/HSDPA/GPRS/EDGE to other phones via wifi, but correct me if i'm wrong lol.
what i want to do is basiclly have wifi on the pc using the pda's built in antenna...
Thanks for the tips on the router, we'll try that
i know what those acronyms mean i just don't know how to configure them for the internet sharing program...
The ICS only shares your mobile internet with one computer be it on USB or BT, it can't act as a wifi adapter... The WMWifiRouter uses the ICS, but with different settings, that can't be utilized manualy... you can create an Ad-Hoc network with some registry tuning, but that's about it.. no DHCP, no NAT, no WEP, nothing that makes it easy, and secure...
Also I mentioned a version number for WmWifiRouter... the leatest (1.20) supports the Wifi -> USB mode, so with this your PDA can act as a WiFi adapter.
Also these PDAs weren't ment to be used this way, so expect high-level battery drainage, you'll need atleast 2 USB ports to charge it while using WMWiFiRouter.
But you can download the trial from the site, and see for your self... you won't loose anything with trying...
gnick666 said:
The ICS only shares your mobile internet with one computer be it on USB or BT, it can't act as a wifi adapter... The WMWifiRouter uses the ICS, but with different settings, that can't be utilized manualy... you can create an Ad-Hoc network with some registry tuning, but that's about it.. no DHCP, no NAT, no WEP, nothing that makes it easy, and secure...
Also I mentioned a version number for WmWifiRouter... the leatest (1.20) supports the Wifi -> USB mode, so with this your PDA can act as a WiFi adapter.
Also these PDAs weren't ment to be used this way, so expect high-level battery drainage, you'll need atleast 2 USB ports to charge it while using WMWiFiRouter.
But you can download the trial from the site, and see for your self... you won't loose anything with trying...
Click to expand...
Click to collapse
Ok, i got the 1.20 trial on the pda and got it working in Wifi -> usb mode, but now how do i search wireless networks on the pc? i noticed it is detected as wired connection, not a wireless one...
You don't need to quote the previous reply...
The PC sees a wired connection... so? You thought that, you can use the windows Wireless Zero Config for searching? I guess you just found out that you can't...
The wireless connection is managed by your PDA, connect to a wireless network with you PDA after you set up the WiFi -> USB...
gnick is correct, I am actually using my phone at home as a Wifi Adapter with WMWifiRouter 1.25 and it works very well. And YES, you have to connect your Wifi on phone first, then connect phone to computer via USB and (in my case) Windows 7 does the rest... I believe Vista also. Not sure about XP, don't have an XP machine, well I do, but it's off sitting in the closet (in timeout for not behaving good.. hehe)
Hi,
At my university they have WiFi in all the buildings.
I can connect to the modem without a problem, but to have acces to the internet I have to connect through VPN otherwise it won't let me browse the web.
So I go to Settings>connections>VPN and I put all the data in it like pptp,username,pass and server, I don't know what I have to chose for 'Make connection from (internet, work, mss, wap, ipaq wap)... and Make connection with(internet, work, mss, wap, ipaq wap)..."
My question is how can I activate that VPN setting?
I connect to wifi but there is no such thing as launching the vpn settings in it...
Plz help, thx!
grtz