I have paired my Sony Ericsson HBH-GV435a bluetooth handsfree to my new Touch Pro. Every time I make a call or respond to a call and hang up the BT connection hangs too and the handsfree disappears from the phone. If I power off and re-power on the BT handsfree the connection reestablishes until the next call comes in and I hang up where the BT connection hangs/disconnects again. My other BT (Jabra 250) works fine with no disconnections. Touch Pro BT settings and Sony BT settings are the default ones.
Any suggestions how to keep the Sony - HTC BT connection alive? Any tweaks?
Not sure if I understand 100% what you mean.
I noticed it with WinMo 6.1, the ROM I'm using right now(see sig) and other Raph ROMs that the BT device icon is OFF but BT itself is on. That's valid for 100% of the cases, the device icon and thus true communication to this device seems the be activated only on demand/when used and it takes less than a sec to do so (IMO great to conserve some battery power).
Let me describe (BT paired to know device):
BT headset on
BT at phone on (BT symbol on top/no headset symbol)
Open dialer, no headset symbol
Dial and a sec later headset symbol appears in dialer
Hang up (BT symbol on screen goes quickly off/on, headset symbol disappears).
The same with the - though nagging - incoming call delay:
Softkey lights blink
Incoming dialer screen pops up without headset symbol
Headset symbol appears and starts to peep ...
Thank you my friend! You solved a big mystery for me...I tested it and you are right, once a call comes in again the SE BT device gets automatically reactivated after a small lag and reconnects with no problems. I was losing the handsfree icon in the dialer and I was getting a "lost BT phone" tone in my handsfree and was misled to believe that the connection is lost. The connection indeed drops but reconnects on demand on next call. Great help! (was about to toss the handsfree to garbage!)
Related
I use Tomtom frequently and use a bluetooth headset to handle my phonecalls. However when I use Tomtom, I want to hear the navigation instructions from the phone speaker and not from the headset. When I recieve or make a phonecall: vice versa.
I have come up whit a workaround solution. I use BTtoggle to turn bluetooth on while navigating if I receive a phonecall, takes some time and then anwser the phonecall through the bt headset. And then with alttab back to tomtom, so that I can see the route and calling at the same time. It's not perfect, but it does the job.
I want to have this done automatically by the phone. If I am navigating and a phonecall comes in, then the phone automatically turns on the BT, I answer the phone and tomtom remains on the screen. If i am done with the conversation, bluetooth turns off and i hear the voice from tomtom again through the phone speaker....
Does anybody know how this can be done? I have seen a Palm application which could do the trick...(by the way, it has got the same name as the bt toggle app: BTtoggle)...
Hello,
a friend of mine have some troubles with his TP and a Blaupunkt Radio with build in handsfree.
The Bluetooth pairing was completed without any problems.
When a calls comes the radio mutes and switch to handsfree - thats ok
The caller can hear your voice over the handsfree microphone, but you can't hear the caller. It is the TP build in speaker used, not the handsfree speaker.
The TP has the headset symbol shown in the upper right corner of the dialer.
Second the radio don't switch back to radio when the call ist ended the Bluetooth Connection stays up. Only deactivating/activating of Bluetooth at TP closes the connection and the radio switch back.
I hope somebody can help me...
Thanks!
I had this problem with my TYTN using shaps rom. you ave to turn on the hands free on the first incoming call and then further calls are OK. (right menu and turn on hands free)
this has to be done every time you get in the car though.
Its a pain i never found a fix. I havnt used this on my Touch Pro yet.
With Pioneer DEH55BT all working fine.
Thanks for the workaround... Perhaps it works for my friend, i will test it in the afternoon.
But another radio is no solution,it have to be this!
Try installing jetware mobile, it improves the bt connection but I don't know if it will solve your problem.
Hello
When there is no signal (no phone service), e.g. in subway, I get regular every 10 seconds beep notification into the BT A2DP headset.
My phone is Xperia, WM6.5.
Any idea, how to get rid off this notification in Windows Mobile?
Thanks
Peter
Hi,
I would love to see a way/program that maxes out the volume when the HD2 gets connected to a bluetooth carkit and switches back to normal when connection is lost/disconnected.
I now often have the problem that the sound on my HD2 is very low when I get an incoming call on the carkit so that I have to get the phone out of my pocket to turn op the volume (other ways the car radio needs to go on 80% (normal 35%/40% with phone sound on max) or more, not nice with 250+ Watt RMS on it when the call stops and the music starts again)
plz. help.
Hi all,
I have HP iPAQ 514 with TomTom 7 installed on it, my goal is to hear all the TT's voice instructions through my bluetooth headset.
I've experimented with several settings as my headset is A2DP enabled, the result is that my phone is not fast enough to run TomTom and encode A2DP at the same time, so in the bluetooth settings of the phone I've unchecked Wireless Stereo and left only Hands Free checked for my headset.
Through standard hands-free profile it works, but with lags, i.e. I hear about 1-2 seconds sound from the phone speaker, then it's switched to my headset. Sometimes, if an instruction is too short, it switches even after playing it, so I don't hear anything. After a few seconds of inactivity, it switches back to "standby" mode.
I've found out I need to keep the connection between phone and headset "alive" to get rid of those lags - e.g. by playing music in the background, then there are no lags as the connection is active. But playing some sound (even playing "silence" just to force permanent connection) means extra load for the processor and the memory, and is very unpleasant. Is there any other way to keep my phone permanently connected with my bluetooth headset, not in just lag causing "on-demand" mode?
Thanks a lot.