Related
I'm wondering if this is because of my device (HTC Titan) or because of WM6... all I know is that I never had this happen before!
Basically, I'll pull out my phone sometimes and find that its turned on by itself, and has been sitting with the dim idle backlight on.
I noticed it can be caused by several things but the 2 main ones I've seen is:
1) when the phone switches to/from roaming, it wakes up
2) when using A2DP controls (AVRCP), it wakes up.
I've been using workarounds to keep the backlight off for now (set the phone to roam only, or carrier-only, so it won't be switching in/out of roam, and use core player or just remember to toggle the screen off everytime I use a media AVRCP control), but there has got to be a better way to keep the darned screen off until I press power!
Anyone have any suggestions? This is really an unexpected annoyance as it eats up my battery quickly not knowing its on...
I had a similar issue with whenever I received an email and didnt shut off the device manually. What I eventually ended up doing was setting the device to automagically lock when it was powered off, and this seemed to solve the issue. I'm not sure however if this will fix it in your case because locking it may interfere with AVRCP controls working.
To everyone using TomTom not just in your car !
Is it possible to stop the auto minimize of TomTom's windows when you turn OFF then back ON your PPC screen ?
I know I can revert back to TomTom from the tray icon, BUT it is very annoying and boring to do that ! When you use your PPC outside your car, you often want to check just for a few second your PPC to check that you are on the right direction ! you do NOT want to have your PPC always ON !
And you must also consider a power limitation, when you are on foot, you do not have a car battery next to you to power up your PPC, so it is essential to be able to turn ON/OFF your PPC screen to save battery life.
-> but TomTom's window always disappear in that process, how to avoid this !
Good question. I'd also like to know this. Sometimes I get on a 30 mile straight or stuck in traffic, so could do with turning the screen off to save energy
I'm afraid this isn't a solution, but a quick workaround would be to set one of your ftouchflo gestures to tomtom. Then you could maximise it with a simple sweep.
jez83uk said:
I'm afraid this isn't a solution, but a quick workaround would be to set one of your ftouchflo gestures to tomtom. Then you could maximise it with a simple sweep.
Click to expand...
Click to collapse
Yes, a workaround, I have tested it but surprisingly it TomTom does not come back immediately like any other program when they are minimized !
It takes about 2s to comes back.
That's annoying when you are on foot and you just want to turn on the screen to check if the direction is ok.
Maybe if I remove go to tray icon of TomTom, it will no longer minimize after every switch OFF/ON of the screen.
Does anyone know how to stop TomTom tray icon feature ?
Slightly off-topic
Any way to stop ActiveSync when TomTom is launch?! Minimize I can live with, but ActiveSync is more annoying.
Has someone an idea, what causes Tomtom to minimize every time you turn OFF/ON the screen display ?
I would like to do a skschema script to fix this. But I need to investigate what causes this minimization ?
bump
I too am trying to find out if its possible to prevent tomtom minimizing and stay running when the backlight is turned off. Other GPS programs i use stay running and dont minimise as well as other programs in general so i am assuming its some kind of power saving function of tomtom. Im assuming it changes something or monitors something to auto minimize itself when it sees the backlight go off.
Hallo, i,m new here and i hope my message will go ahead.
So far I made following observance.
Today i nstalled a new beta version of mortPlayer V3.31 b75.
After i had installed mortplayer and it is running then TomTom does not minimise. after deactivating my HTC 7500; WM6 Tomtom 7
Perhaps it will show equal behavior on other systems
Good luck
nope, still minimizes and stops using GPS when screen goes off even with this version of mort installed. Maybe share the settings so i can see if how you have it set works for me.
Tomtom minimising
even on my Dell x51v TomTom does not minimise when I turn off for a sleap,If you mean the GPS mode shouldn´t be turned off while sleaping , so am I not sure wether it is possible,and even if it is ,it would drain battery .
What i mean is, i want TOMTOM to stay running while the device has the screen turned off. This way it will save battery life as i cant look at the screen while im on the motorbike.
Same Here
I also would like TomTom to behave like other application.
Because it goes to the tray:
- you have to try to hit that small icon in the tray with your finger, or pull out the stylus
- you can not use that Alt-Tab, to switch away and back
- it does not show up in task manager
- if you assign a button to it, it take a few seccond to show up (but it's instant when you hit the tray icon)
- waste Today screen space...
So like the others, I would appreciate help on changing that behavior.
Thanks in advance
I want to use my TouchPro for tracking a long route i will be travelling shortly. When I turn of my device using the button on top when using a gps tracking-tool, the gps will disconnect and need to search for satellites again after turning on the device.
Does anybody know a trick (maybe in the registry) to keep the GPS alive?
I am also curious about this.
Finally I managed to find this thread!!! I am also facing this problem and was wondering if there was anyway to prevent the GPS from closing and losing connection with satellites when the phone goes into sleep mode. Anyone with any ideas PLEASE HELP!!!
Btw I am using TomTom Navigator 7 with Australian maps...
camielkb said:
I want to use my TouchPro for tracking a long route i will be travelling shortly. When I turn of my device using the button on top when using a gps tracking-tool, the gps will disconnect and need to search for satellites again after turning on the device.
Does anybody know a trick (maybe in the registry) to keep the GPS alive?
Click to expand...
Click to collapse
I seem to recall that TrackyPro has a function which will turn the screen off whilst still tracking the route. Is that the type of thing you're looking for?
Well basically I just want the GPS to still have the lock on the satellites EVEN when the device goes into standby. It's frustrating when after 3 minutes (my settings for power management) the device goes into standby and you realise that the GPS is closed when you turn it back on. So yup, as you said correctly, I want the GPS to still function even when the screen is off. Please guide me to wherever I can get the solution as I use alot of GPS!!!
All good GPS software should have option to keep device on all the time while GPS fixed.
I dont think it's possible to keep GPS on while device is on standby mode. Anyway, GPS should stay on even if screen light is turned off for power save.
Well I am using TomTom Navigator 7 with Australian maps, and I have tried looking at the options in TomTom and I couldn't find any setting to keep the screen turned on while GPS is working. And you are correct in that applications such as GPS and Bluetooth are impossible to stay running when the device goes into standby, as this feature is an OEM feature in all Windows Mobile devices to save power. The only way out I see, is to go to Settings>System>Power>Advanced and untick 'Turn off device if not used for...' This way the backlight can be turned off (which saves power) but the device itself is not totally off. This method will still consume power since the device is technically not in standby, but it's probably the best we can get since there is just no way to have GPS to function with the screen totally off ie in standby.
avantgarde84 said:
Well I am using TomTom Navigator 7 with Australian maps, and I have tried looking at the options in TomTom and I couldn't find any setting to keep the screen turned on while GPS is working. And you are correct in that applications such as GPS and Bluetooth are impossible to stay running when the device goes into standby, as this feature is an OEM feature in all Windows Mobile devices to save power. The only way out I see, is to go to Settings>System>Power>Advanced and untick 'Turn off device if not used for...' This way the backlight can be turned off (which saves power) but the device itself is not totally off. This method will still consume power since the device is technically not in standby, but it's probably the best we can get since there is just no way to have GPS to function with the screen totally off ie in standby.
Click to expand...
Click to collapse
I don't think that TT has the option you need - it takes its power options from the device (including screen brightness). That is probably because TT probably thought most people would have their device plugged in whilst navigating given the power required for navigating with the screen on.
I find that another side effect of this is that if I am driving on a bright day, I need to turn off the auto light level feature of the Raph to make sure the screen is as bright as possible.
avantgarde84 said:
Well basically I just want the GPS to still have the lock on the satellites EVEN when the device goes into standby. It's frustrating when after 3 minutes (my settings for power management) the device goes into standby and you realise that the GPS is closed when you turn it back on. So yup, as you said correctly, I want the GPS to still function even when the screen is off. Please guide me to wherever I can get the solution as I use alot of GPS!!!
Click to expand...
Click to collapse
I think it's a matter of semantics, but it may help you find a solution faster:
What you need is a tool / solution / procedure that turns only the screen off WITHOUT putting the phone in standby mode. Try searching for that; if you include the whole GPS tracking wish then you might not find what you're looking for so quickly.
Good luck and let us know if you found something that works for you!
Just curious as to what tracking software is used?
Our free PocketReperion tool does keep the device from entering standby mode.
It's free software.
We just lauched a special version for the Raphael, v.1.53
Coolest thing is that you canupload audio / video / photo's and people who are trascking you (live) will see all the content you upload, on the spot that you uploaded it.
get the free client here :
http://www.reperion.com/newclient
be sure to register for a free account first, read the readme in the directory above
EDIT : SUPPOERTED MAPS :
Google Earth
Google Maps
Google Maps Mobile
Virtual Earth
Virtual Earth Mobile
Mappoint 2009
Yahoo! Maps
MapQuest
checkout the example at http://tracker3.reperion.com/wrldmap.aspx?name=d-8498
BETA : http://www.reperion.com/beta
Coromoto said:
I think it's a matter of semantics, but it may help you find a solution faster:
What you need is a tool / solution / procedure that turns only the screen off WITHOUT putting the phone in standby mode. Try searching for that; if you include the whole GPS tracking wish then you might not find what you're looking for so quickly.
Good luck and let us know if you found something that works for you!
Click to expand...
Click to collapse
As far as I always remembered, the only time the screen can be turned off is when the phone goes into standby. In other words screen off=standby and vice versa and no other way to breakup this association. The option I have considered is what I have mentioned above, ie just letting the backlight turn off, but NOT turning the device off. But this will be a problem if you need to look at the screen constantly for navigation and cannot survive with just voice navigation. If you really do need the backlight to be turned on all the time, then go to Settings as well and untick the TUrn off backlight option too. Power will be gone in no time, then you probably will need to consider a in-car charger then...
lucid said:
Just curious as to what tracking software is used?
Our free PocketReperion tool does keep the device from entering standby mode.
It's free software.
We just lauched a special version for the Raphael, v.1.53
Coolest thing is that you canupload audio / video / photo's and people who are trascking you (live) will see all the content you upload, on the spot that you uploaded it.
get the free client here :
http://www.reperion.com/newclient
be sure to register for a free account first, read the readme in the directory above
EDIT : SUPPOERTED MAPS :
Google Earth
Google Maps
Google Maps Mobile
Virtual Earth
Virtual Earth Mobile
Mappoint 2009
Yahoo! Maps
MapQuest
checkout the example at http://tracker3.reperion.com/wrldmap.aspx?name=d-8498
BETA : http://www.reperion.com/beta
Click to expand...
Click to collapse
Thanks mate, will give it a test and see how it goes...
Hi, first post for me
I have wanted to do exactly the same thing, that is, keep the GPS tracking on my HTC Touch Diamond with the phone in "off" mode. The only way I have found to do it, is this; play music via a Bluetooth headset (you can pull out the jack-plug too, so no actual sound is heard). Now when you turn the phone "off" the GPS will continue to track.
There probably is some simple software out there that would work better, but this is my solution
Cheers
Perhaps this helps...
Go to HKLM\System\CurrentControlSet\Control\Power\State\Suspend
and create a DWord value named NAV1: with value decimal 0 (0 means power on and here is a complet list of values)
This allos HTC GPS driver to stay on on suspend mode. I think this allows any application accesing GPS to get data while the PDA is off.
Can someone test it and report back?
If this works, i can create a CAB to easily deployment.
Cheers
Cheers
jcespi2005 said:
Perhaps this helps...
Go to HKLM\System\CurrentControlSet\Control\Power\State\Suspend
and create a DWord value named NAV1: with value decimal 0 (0 means power on and here is a complet list of values)
This allos HTC GPS driver to stay on on suspend mode. I think this allows any application accesing GPS to get data while the PDA is off.
Can someone test it and report back?
If this works, i can create a CAB to easily deployment.
Cheers
Cheers
Click to expand...
Click to collapse
Hi there, thanks alot for your discovery, will surely test it out later. With TomTom Navigator that I am using, once you have planned a route and it starts to navigate, the screen stays on forever. What I said earlier in my previous posts are irrelevant since TomTom just keeps the screen on and never dims the backlight nor turns off the device. So unchecking the Turn Off Device after XX mins is useless. Anyway we need some fix which can 1) Allow us to turn off the screen to save power but still have TomTom running and giving us navigation instructions and 2) Does not disconnect from satellite fixes when device is put into standby.
Your reg edit sounds like it will work, but will have to confirm it first. A cab file will be really appreciated. Cheers!
EDIT: preliminary testing: Turned on GPS outdoors, managed to get a satellite fix. Did not plan any route. Turned off screen (ie standby), turned back on, GPS signal was lost. Had to wait few seconds to reconnect to the satellites. Unsure about voice navigation while screen is off but since when I turned the screen back on the signal was lost already I don't think there will be any navigation when screen off. In short --> DOESNT WORK.
I didn't read through everyone's response, but what about just using a car charger, and setting the power settings to never turn off when turned on? You can turn down screen brightness if you're worried about the screen itself, but that should keep you connected at all times, and the battery should remain charged as well.
This also avoids registry tweaks that may have side effects. Simple, and painless in my mind.
avantgarde84 said:
EDIT: preliminary testing: Turned on GPS outdoors, managed to get a satellite fix. Did not plan any route. Turned off screen (ie standby), turned back on, GPS signal was lost. Had to wait few seconds to reconnect to the satellites. Unsure about voice navigation while screen is off but since when I turned the screen back on the signal was lost already I don't think there will be any navigation when screen off. In short --> DOESNT WORK.
Click to expand...
Click to collapse
The change of NAV1: only affect to GPS device, so perhaps the nav software need more devices to stay on to work (or really the soft changes the power state of devices itself). I tested the changes above with HTC GPS Tool and seems to work, but seems navigation software are not the same... sorry.
Cheers
I'am using the IGO8 Navi Software on my Touch Pro.
I ride by mountain bike often and today I wanted to save the track I normally ride.
I turned on IGO 8 and get a satellite fix and started riding, when I came to my first check point I realised that on stand by mode, the IGO8 wasn't getting satellites.
So I minimised the IGO8 and I had the today screen on. I unticked turn-off device and turned the keylock on.
This was my only solution, it would be great to have the GPS running when switched off.
doublecheese said:
I'am using the IGO8 Navi Software on my Touch Pro.
I ride by mountain bike often and today I wanted to save the track I normally ride.
I turned on IGO 8 and get a satellite fix and started riding, when I came to my first check point I realised that on stand by mode, the IGO8 wasn't getting satellites.
So I minimised the IGO8 and I had the today screen on. I unticked turn-off device and turned the keylock on.
This was my only solution, it would be great to have the GPS running when switched off.
Click to expand...
Click to collapse
Trackme has a GPS powersave mode which allows the screen to be turned off but will still record your track. http://forum.xda-developers.com/showthread.php?t=340667
Thanks
Let me check it out.
Ok people. By now everybody knows that the gps antenna sucks on touch pro or fuze. We have tried almost everything and I have done all the reading and I am so surprised that no one has really solved this but me.
I can get a gps lock in about 3 to 6 seconds all day long. All you have to do is to either disable the manila and have a regular today screen or get the program called second today from xda site (If you like to have the manila 3d stuff on your phone which I do) and once you are done, then install gps today ( get that from geoterrestrial.com).
Once you install the program (ITS FREE PEOPLE) then just set it to auto by clicking on the red rectangle thing on the left side to turn the gps on. The first time will take about a minute or two to lock and once its done, you will be able to get a lock in about 3 to 6 seconds. It is very fast and accurate. It is a good idea to go to its setting and set up everything the first time to make the lock as fast as possible.
By the way you will need to get the plugin version not the full version ( it means that it will be a little plug in on your today screen about 4 icons).
I use this method to get a quick lock and then i turn google map or tomtom on and they work like a charm. If you do a soft reset, it will take longer to get a lock because it doesn't keep any memory.
I have used xda for a long time and thought that I should give something back to my dudes and dudets. Thank you for all your hard work. Ben
If you have it on manual mode, it will not USE ANY BATTERY AT ALL SO DON'T WORRY.
Here is new information for my people. For faster cold fix before using gps today update your quickgps. that will get gps today working in a cold start really fast. thanks
ben1do1 said:
Ok people. By now everybody knows that the gps antenna sucks on touch pro or fuze. We have tried almost everything and I have done all the reading and I am so surprised that no one has really solved this but me.
I can get a gps lock in about 3 to 6 seconds all day long. All you have to do is to either disable the manila and have a regular today screen or get the program called second today from xda site (If you like to have the manila 3d stuff on your phone which I do) and once you are done, then install gps today ( get that from geoterrestrial.com).
Once you install the program (ITS FREE PEOPLE) then just set it to auto by clicking on the red rectangle thing on the left side to turn the gps on. The first time will take about a minute or two to lock and once its done, you will be able to get a lock in about 3 to 6 seconds. It is very fast and accurate. It is a good idea to go to its setting and set up everything the first time to make the lock as fast as possible.
By the way you will need to get the plugin version not the full version ( it means that it will be a little plug in on your today screen about 4 icons).
I use this method to get a quick lock and then i turn google map or tomtom on and they work like a charm. If you do a soft reset, it will take longer to get a lock because it doesn't keep any memory.
I have used xda for a long time and thought that I should give something back to my dudes and dudets. Thank you for all your hard work. Ben
Click to expand...
Click to collapse
I should probably start by saying that I've only had my Touch Pro since Christmas, and am still getting to grips with it, but I've not seen the GPS issues that other people have reported.
Your solution to the problem simply keeps the GPS switched on all the time, and I think this may have a negative impact on battery performance. My wife has a Samsung Omnia i900 which has GPS issues in TomTom which can be fixed by installing GPSGate - however, unless you make it idle while nothing is using GPS, then it will keep the GPS active constantly (like your solution) and she noticed an increase in battery drain.
Cheers,
Steve.
I was concerned about that but even if you do automation off and turn it on manually (this way it will not affect your battery) it will still work flawlessly. I have tried it at least a hundred times over the last 2 months and this is the only way to get the lock fast.
All touch pros have this gps issue and if you try to get a lock with google map or tomtom alone it sometimes take over 5 minutes to get a lock. With my method it only takes a few seconds every time. this is important for people who use their gps all the time to find addresses or sales people on the road who don't want to prey for minutes to get a fast lock. thanks
ben1do1 said:
I was concerned about that but even if you do automation off and turn it on manually (this way it will not affect your battery) it will still work flawlessly. I have tried it at least a hundred times over the last 2 months and this is the only way to get the lock fast.
All touch pros have this gps issue and if you try to get a lock with google map or tomtom alone it sometimes take over 5 minutes to get a lock. With my method it only takes a few seconds every time. this is important for people who use their gps all the time to find addresses or sales people on the road who don't want to prey for minutes to get a fast lock. thanks
Click to expand...
Click to collapse
ok sooooo im not trying to burst your bubble as i would love to have a 3 to 6 sec connect time but if use google maps or tomtom to connect for the first time then close out and open it right back up you will get about the same 3 to 6 second connect time when is what the app does..... sorry
not really, even if you have gotten a lock with google maps or tomtom and you try turning it on a few hours later, sometimes it takes 5 minutes or more to get a lock. There was a time that I had to stand in the street with my phone facing the sky and praying to get a lock and that was embarassing.
In some cases I didn't get a lock at all even after a few minutes since there were some tall buildings around me (downtown los angeles) trust me I have gone through all that and I was going crazy over this issue. I have tried it all because I need the gps lock all day long for my job. The gps today program uses a different method to get a lock. I don't know what it does but whatever it does, it works. thanks
try it ITS FREE. what have you got to loose? you will thank me.
by the way Steve, it does not keep the gps on all the time. It only turns on for a few seconds, gets a lock and turns off (on the auto). thanks
Fair enough - I'm not sure how it would manage to get a lock indoors. I guess I must be lucky though, as I've never had to wait anything like 5 minutes for a lock. I do use QuickGPS, but not AssistedGPS, and don't seem to have to wait very long for a lock at all (if I'm outside).
do you realize what kind of "solution" you give?
you keep GPS always open (you can do that without second today and a GPS today program - you can use GPSGate or keep any GPS program on at all times)
this is dramatic for the battery
this is not a solution, just a bad trick - sorry
I usually get locked in around 15 seconds without turning off anything- I'm using "Automapa 5"- Polish map for mobile devices, works quite fine and locks 10x faster then my hiking GPS (but it's old.. ;p)
Thanks Ben1do1. I just now installed both SecondToday and GPSToday. Your solution works great on my FUZE. Now I can unsubscribe to AT&T Navigator. The only way I used to be able to get TomTom Navigator 6 to get a fix was to run AT&T Navigator (telenav) first.
GPSToday is very configurable and doesn't drain the battery as badly as StevePritchard fears. You can simply disable auto-fix and only do occasional manual quick-fixes just to keep your gps "primed".
below is from the FAQ. http://geoterrestrial.com/faq/
"What does it do to my device's battery life?
In the default configuration, GPSToday will typically reduce your battery life by 10-15% over the course of a day. This much is usually not an issue for the vast majority of users. To have full control over battery consumption, you can disable the automatic periodic quick-fix functionality via Map>Settings. The more frequently you update your fix or run the GPS in persistent mode, the more it will affect battery life."
There you go guys now we are cooking. just turn off the auto and you will not loose any battery. I had sooooo much fun with my gps today and got locks in some cases in 2 seconds. I could not believe my own eyes. Please keep in mind that you need to be outside or close to a big window so that the gps can lock. Enjoy.
I personally think that this thread should be on the wiki and also for the new fuze or diamond owners with the same gps problem. thanks everyone
There's only one way to get a 6 second lock: GPS Hot start. That means that 80% of the birds from the last lock must still be in the sky.
Shephild said:
Thanks Ben1do1. I just now installed both SecondToday and GPSToday. Your solution works great on my FUZE. Now I can unsubscribe to AT&T Navigator. The only way I used to be able to get TomTom Navigator 6 to get a fix was to run AT&T Navigator (telenav) first.
Click to expand...
Click to collapse
did you disable the agps as it would be enabled if you were using at&t navigator... disable it and try tomtom im sure it will work
FYI
FYI - the current version of GPSToday can be installed as *either* a today plugin or standalone app.
i must say that i was sceptic about it but it definitively works for me.
I used to have fixes between 5-10 minuts but with GPStoday i have them nearly instantly, 10-15 sec. Thanks Ben1Do1
Not to cut in but maybe FusionGPSFix can help a little in the same way too.
i cant seem to find the stand alone app... both are today plugs and that's useless in touchflo 3d
I'm beginning to think TouchFlo3D is the problem. I somewhat used what was recommended above. I turned off TF3D and just made a normal today screen in Windows Mobile. I loaded Visual GPS and within less than 10 seconds, I had GPS coordinates. I then turned on TF3D, rebooted (just to make sure everything was cleared out), loaded VisualGPS, it took around 3 1/2 minutes to get a lock. I have repeated these steps several times and every time I do, I almost immediately get VisualGPS to work when TF3D is disable. Someone that knows more about the "internals" of TF3D may can answer this better, but in my testing and troubleshooting that I've done that seems to be the only thing that is making it now work...
erm you are wrong
the first one has a stand alone mode and the second is ONLY in stand alone mode (you don't SEE something happening - it just runs)
After some days trying this the GPSToday Trick i must say it fantastic, really!
before:
first day fix in 5-10 mintutes (AGPS OFF / QGPS ON)
subsequent fixes 3-5 minutes (AGPS OFF / QGPS ON)
with GPS today
first day fix in 20-30 sec (AGPS OFF / QGPS ON)
subsequent fixes 6 seconds (AGPS OFF / QGPS ON)
I don't have the tool always on, i manually turn GPS with this tool whenever i need the GPS.
Try it!
Proven ROM 1.07 + Raphael_Radio_1.08.25.20M1 + GPS Tweaks.cab + GPSTODAY (manual)
Hello everybody!
I'm new to the forum and want to share a problem I got.
Hopefully someone got a solution to it.
I tried to search the forum but couldn't find any similar thread so I start a new one on the issue!
General search on the Internet did show that I'm not the only one who is experiencing this!
Let's get started :
I usually got my z5 in my pocket facing the display to my leg for security reasons, I am working with hard and heavy objects. Everytime a call enters, the display gets activated and stays on afterwards. Meanwhile inside of my pocket several screentouches by my leg may turn on /off flight modus, flashlight, WLAN, data, several applications aso... I really got my phone messed up several times and only got lucky to not have suffered a real damage!
This is possible, because I use smartlock settings by location and Bluetooth headset! Also standby mode enters after 1 minute! Therefore after the activation of the display all apps and quick settings are vulnerable to my leg touching the screen!
I could set display timeout to 15 sec, I could deactivate smartlock settings, but what's the point of it?
These settings are made for usage without having to cause troubles!
Best solution I found in the Internet was to use a screen cover, well that should be the last option for me!
Any app that does the trick?
Any suggestion?
Thanks a lot in advance for any hint!
PS: all sensors are ok, double tap deactivated, smart call features deactivated
--- Resist the Empire ---
Problem still exists up to date, but solution found!
Hello everybody,
I have the same situation, but I fortunately found an open source app that does the trick!
Free without ads on Google play store :
https: [//]play.google.com/store/apps/details?id=ss.proximityservice
Display stays off when call enters and proximity sensor is covered! Also works great while in pocket!