Database Info

Hard SPL Problems

I have problems to use the Hard-Spl v1. I have a new HTC-Kaiser from T-Mobile. I start the Application HARD-SPL (I want to upgrating with Dutty´s ROM)
I run the kaiser-hardSPL.exe on Computer (PC)
I follow instructions on screen!!!!!
on the mobile i the question to start the applikation i answer Yes and then i get a with screen on the HTC Kaiser. NO tri-color-screen !!!
Please help, thx
Thomas

Thomas_Germany_Hamburg said:
I have problems to use the Hard-Spl v1. I have a new HTC-Kaiser from T-Mobile. I start the Application HARD-SPL (I want to upgrating with Dutty´s ROM)
I run the kaiser-hardSPL.exe on Computer (PC)
I follow instructions on screen!!!!!
on the mobile i the question to start the applikation i answer Yes and then i get a with screen on the HTC Kaiser. NO tri-color-screen !!!
Please help, thx
Thomas
Click to expand...
Click to collapse
From what I've read you need to remove your sim card and your microsd card then try again

There is no simcard and microsd in the htc Kaiser.
on the HTC Kaiser is the original T-Mobile software, nothing else

Perhaps your problem is related to new SPL... take a look at http://forum.xda-developers.com/showthread.php?t=349476
Cheers.

When your phone is booting up, look in the lower right corner. If you have a line that reads:
D 1.57.00.00
Then you most likely have the issue in the thread mentioned by jcespi2005. If you have:
D 1.56.00.00
Then its probably something else (as 1.56.00.00 should be able to do the HardSPL).

Why not flash the old SPL to the device then you can use Hard_SPL. I havent checked but arent there original ROM available(of course CID/carrier specific) from before 1.57.

wpbear said:
Why not flash the old SPL to the device then you can use Hard_SPL. I havent checked but arent there original ROM available(of course CID/carrier specific) from before 1.57.
Click to expand...
Click to collapse
The real problem is SSPL used to flash HardSPL is not working with this one, so you can't go back to previous SPL... don't know what shipped ROMs are out that allows flash over this SPL...but perhaps this can be a way to go...
Cheers.

The Rom of my Phone is d.1.56.00.00 !
I do a hardreset, but Hard SPL dont work!

well... for the Tilt you can't flash the "official" ROM back to the device because of an "Invalid Vendor ID", I'm not sure why this is but it just doesn't work. You can however flash the AKU0.4.4 ROM to an unmodified Tilt so the CID apparently is good on that ROM. However I've done this and it does not fix the "white screen" issue on the affected devices.

sirsycho said:
well... for the Tilt you can't flash the "official" ROM back to the device because of an "Invalid Vendor ID", I'm not sure why this is but it just doesn't work. You can however flash the AKU0.4.4 ROM to an unmodified Tilt so the CID apparently is good on that ROM. However I've done this and it does not fix the "white screen" issue on the affected devices.
Click to expand...
Click to collapse
oh well it was an idea. Another reason for me to put off the Tilt purchase.

wpbear said:
oh well it was an idea. Another reason for me to put off the Tilt purchase.
Click to expand...
Click to collapse
I might be returning mine because of this. Bummer.

[UPG]USPL for ELFIN - Only for the brave ones

Hi everybody,
I made up a new version of pof's USPL for ELFIN based on SPL 2.20.0000. You should be able to flash SPL in the third step now.
Why a new version? Because USPL v1 is only for ELF (64/128MB), but not for ELFIN (128/256MB). Flashing the old ELF SPL in step three on a new ELFIN used to brick your device.
EDIT:
You can find the working release in the following thread:
http://forum.xda-developers.com/showthread.php?p=1964159#post1964159
Thanks to everybody who was willing to test this!

Tempting, tempting.
I still haven't reproduced that weird blue screen i once had on my ELF.
But like i just wrote i got's me an ELF.
Good luck finding resourcefull Gamblers.
If there's no luck just start a Donation round for a Bricked Device Garantee

djvw said:
insane people
Click to expand...
Click to collapse
We have a lot of those in this forum. People trying to flash first and then start reading .
Thanks for trying to get USPL working for the XL users!

ummmmm i just used to use the old uspl v1 and exit after step 3 than flash my rom, if you guys are really keen on testing this my new elfin will be here today or on monday and i will try it with my old one just to piss of rogers

shael said:
ummmmm i just used to use the old uspl v1 and exit after step 3 than flash my rom, if you guys are really keen on testing this my new elfin will be here today or on monday and i will try it with my old one just to piss of rogers
Click to expand...
Click to collapse
This is the kind of brave people we need ;-) Please test it and tell us if it's working as soon as you can. Thank you in advance!

Uploaded new version, please redownload in first post.

Nobody has tested this yet?
I think that a Elfin dopod owner can test this without problems, because if don't work he can flash the complete (and signed) dopod rom from bootloader to restore the original SPL...
http://www.dopodasia.com/download/R...7.1B_4.1.13.51_03.07.90_BLUE_Ship_Reduced.exe

i have a elfin locked on bootloader screen....can change my spl with this??

what ??? the UPSL 1.0 is for Elf only and not Elfin ??? what i dont understand is what do you guys mean quit at step 3 ??? I flashed my Elfin with UPSL 1.0 with all steps for more than 6 times so far and nothing has happen so far ... my SPL is the 2.20.2000 one ...

@jamezco:
that´s wrong.
You flashed those roms containing the USPL (start.bat). They automaticly quit the 3rd step and go directly to the Rom Utility to flash the new ROM.
If you use POF´s USPL v1 and you don´t quit after step 3, the patched Bootloader will be flashed from your devices RAM to the ROM, and this wil brick your ELFin. If you have done this, your actual IPL or SPL would be 1.11.xxx...

Sorry: could someone explain me whether it is strictly needed to use the USPL unlock (the one are treated in this post) to flash the PDA?
I mean: the bootloader in the rom package is not able to do that?

we need some thing to unloack direct from boot loader and no need to active sync

as far as i know this is not possible, cause you can´t access bootloader files...in bootloader mode.
same on pc, you can´t delete or replace files, which are open/inuse by another program...

STRAFALCIONE said:
Sorry: could someone explain me whether it is strictly needed to use the USPL unlock (the one are treated in this post) to flash the PDA?
I mean: the bootloader in the rom package is not able to do that?
Click to expand...
Click to collapse
The Rom Packages u can get here don´t contain a bootloader...and even if they would, the bootloader or the rom would have to match your model ID for flashing it to your device....so yes, it´s stricktly needed to CID unlock to flash Custom ROMs or ROMs with other vendor IDs.

Could someone help me? The USPL is needed for the flashing of ROM, or is it enough the bootloader of the ROM?

Sorry, I missed the answer of the post before
My eyes are crossing after 12 hours in front of the pc

Anyone tested already???

Come on guys,
somebody who can get official Roms from his provider should give this a try...

Hi all, not that i think myself insane but i have tried the USPL for my Elfin 128/256 Touch a few days ago . I have followed the steps and the screen turned white as mentioned by the installer after that it booted up fine again.
Everything seems to be working fine!
However, i have not seen any change to the device..

mb286 said:
Hi all, not that i think myself insane but i have tried the USPL for my Elfin 128/256 Touch a few days ago . I have followed the steps and the screen turned white as mentioned by the installer after that it booted up fine again.
Everything seems to be working fine!
However, i have not seen any change to the device..
Click to expand...
Click to collapse
You don't see any change in the device.... but if USPL works you can flash ANY rom from bootloader directly executing RomUpdateUyility, you don`t need to boot windows, activesync and white screen (temporary SuperCID) to flash, try.....
Go to RUU directory and execute RomUpdateUtlity instead of RUN.bat and see if you can flash any rom without 3% (corrupted) error....

Noobie Hard spl question

NOt sure if this is in the right topic, but its slightly rom related.
Can someone please help a noob
I cid unlocked my phone following the topic
http://forum.xda-developers.com/showthread.php?t=375583.
all worked well, tried a couple of roms and settled on
L26 WM 6.1 Professional WWE V6a (MMS and JAVA updated) rom, seems to be working ok, certainly all my apps work.
However like a typical noob I missed out on some important reading about hard spl and how it can protect my phone from a bad flash.
Now that I've done all of the above, is it too late to go back and protect my phone with hard spl?
SPL -1.0. Olipof
thanks in advance

I think that's done automatically when you flash hard spl.
(someone correct me if i'm wrong please)

step one in that unlocker would have flashed hardspl on your device, if u skipped it then no, its not too late, you can still do it now

XtreMe_G said:
step one in that unlocker would have flashed hardspl on your device, if u skipped it then no, its not too late, you can still do it now
Click to expand...
Click to collapse
No i didnt skip step one, so I guess I'm covered.
Guys thanks for the help, much appreciated!

Just go into bootloader mode (power button + camera button + reset). If the screen shows SPL-1.0.OliPof then you are ok. If not then just reflash hardSPL.

SPL-1.0.OliPof is there in bootloader.
thanks for the help guys.!

[UPG] READ BEFORE FLASHING! Hard-SPL 2.28/3.10/etc - yes with overwrite protection :)

well so finally here's a real hardspl =)
it's based on USPL's - new feature is overwrite protection. so devices won't get bricked if flashing a full shipped rom. the version after flashing this will be "xx.xx.cmon" (ending in cmon).
btw, this uses same CID patches as the 3.07 USPL made by htctouchp but i removed modelid patch after determining it wasn't necessary (makes it safer by not allowing to flash other devices' roms).
also thanks to htctouchp for testing this hardspl.
NOTE that shipped roms with SPL.NBH included will fail to flash until the SPL.NBH is removed (in the past this would have resulted in a brick, now hardspl protects you from this).
also, all these hardspl's include the size patch to allow flashing smaller images via RUU!
usage: download from attachment, flash with pof sspl, enjoy
or if you already have some version of uspl, then just use that to update straight to hardspl. (but after installing hardspl you will always have to use sspl if you want to change spl version, see detailed instructions below.)
more detailed instructions:
this is to flash any SPL: either update to hardspl this way or flash another spl over hardspl. (copied from other post)
0. make sure your device is synced to activesync!!
1. Run the elf-uspl.exe from ELF_USPL_2.26.0000.zip
2. Watch Screen and Press Enter When Asked.
3. Screen should Jump to White on Phone and on PC Flashing Loading Bar will Show.
4. Stuck in Black Ducky Loading Screen?, check Active Sync Connection or Do a hard reset on Phone first. But be sure to do the last Actual Flashing in White Screen. Sometimes this needs a few tries to go through white screen.
5. Done.
UPDATE: 2.26 and 2.28 hardspl's: 2.28 is best if 3.x versions don't seem to work on your device. very stable because it seemed to work on any elf/elfin so far.
...get them from attachments in this post,
and thanks to htctouchp (Aman) for saving me time by editing these!
UPDATE: 3.10 HSPL: Aman found a new SPL update and ported my hacks to it, thanks attached to this post too.
UPDATE: 3.14 HSPL: Aman found yet another new SPL update and again ported my hacks to it; newest attachment in this post. new feature: cool picture while device is charging!! if you don't like the idea of the device being on in bootloader when it's not in use just charging the battery, you can stick to 3.10 or 2.28.
[SIZE=+2]IMPORTANT: 2.26 and 2.28 are for both Elf and Elfin, but 3.07 and 3.10/3.14 sometimes don't work on 64mb Elf so if you have that device, test with USPL version first[/SIZE]
still, if you've managed to flash the wrong version, then to unbrick, see for now: http://forum.xda-developers.com/showpost.php?p=3395787&postcount=155
[SIZE=+2]IMPORTANT 2:[/SIZE] [SIZE=+2]3.14 can Cause Larger Battery Drain then expected.[/SIZE]
Further Plans When I Get The Time:
- better integration of SSPL loader, and check included to prevent 3.xx installing on Elf's
- user friendly unbricking
finally, donations are always appreciated to "To Cmonex" link in my signature

Nice Work - do you ever sleep
I'll sticky this for you cmonex.
Dave

let me be the 1st one to say
THANK YOU
you are the best!! simply the best

Thank You
kokotas said:
7. CID Unlock your phone
...
(4) Elf&Elfin HardSPL (Not available yet)
...
Click to expand...
Click to collapse
Always wanted to change the above statement in the RollUp...
You made it true!
Thanx!

will wonders never cease. finally a hardSPL. thankx a lot bro...

I Wish I had this Before I tried To Flash The New 6.1 Rom LOL -
Had To Use the Goldcard to method to unbrick. Well At least I unbricked it And now I wont have to worry about that again thanks to this

Last night I stack at tricolor screen. can this help me and how? Sorry I'm new here.

cmonex said:
well so finally here's a real hardspl =)
it's based on 3.07 -..
finally, donations are always appreciated to "To Cmonex" link in my signature
Click to expand...
Click to collapse
Thenx

Thanks cmonex for this HardSPL...
malintzin said:
Last night I stack at tricolor screen. can this help me and how? Sorry I'm new here.
Click to expand...
Click to collapse
No sorry it's too late.
but try the gold card unbriker

But Wont This Lock Your SPL
So If You Want To Update To A Older Or Newer SPL Then You Wont Be Able To Please Let Me Know Cause I Justed Used This And I Tried To Down grade the SPL and I Was Unable To

Thank you so much cmonex! what would we (or at least I) do without you and Olipro!

RaffieKol said:
But Wont This Lock Your SPL
So If You Want To Update To A Older Or Newer SPL Then You Wont Be Able To Please Let Me Know Cause I Justed Used This And I Tried To Down grade the SPL and I Was Unable To
Click to expand...
Click to collapse
as mentioned by cmonex, u need to use SSPL to flash another SPL i.e. elf-uspl.exe, the white screen method, which u were using before to flash the USPLs.

AWESOME work C!! once again the legend of PPC hacking strikes back
Wish I still had my ElfIn, would had been so much fun still cooking for this device now

ababrekar said:
Wish I still had my ElfIn, would had been so much fun still cooking for this device now
Click to expand...
Click to collapse
then i've an offer.. lets exchange our devices

htctouchp said:
then i've an offer.. lets exchange our devices
Click to expand...
Click to collapse
Is Diamond really better?

dsixda said:
Is Diamond really better?
Click to expand...
Click to collapse
may be... may not be ...
PS: its time to change your signatures from USPL to HSPL

htctouchp said:
then i've an offer.. lets exchange our devices
Click to expand...
Click to collapse
Yeah right
dsixda said:
Is Diamond really better?
Click to expand...
Click to collapse
Dont know about thr world but I find it fancy rather than better Also with a higher cpu, its a bit fast too

htctouchp said:
PS: its time to change your signatures from USPL to HSPL
Click to expand...
Click to collapse
hehe.. So does it work fine on Elfs with cooked ROMs?

dsixda said:
hehe.. So does it work fine on Elfs with cooked ROMs?
Click to expand...
Click to collapse
i don't have an Elf to test... anyway i'm also working on HSPL 2.26 and 2.28 for those who only use USPL 2.26 or 2.28 . once i finish, will send them to cmonex for approval.

htctouchp said:
i don't have an Elf to test... anyway i'm also working on HSPL 2.26 and 2.28 for those who only use USPL 2.26 or 2.28 . once i finish, will send them to cmonex for approval.
Click to expand...
Click to collapse
Awesome man... if you buy a Diamond you have to pass the knowledge on to me
LOL

[REF] Kaiser Hard SPL Rollup Thread.

There are now a large selection of Kaiser Hard SPL's floating about. I am making this thread as a collection for all of them and the instructions for flashing them.
Explanation
WM Version - Different SPL's perform better depending if you are running WM6.0 or WM6.1. If you are using a WM6.0 ROM, you should be using a WM6.0 Hard SPL (v1 is recommended). If you are using WM6.1 any 3.* SPL is recommended.
Hard SPL Version - Most WM6.1 ROM's are based of a 3.* release by HTC / ATT. The 3.* Hard SPL version should match this the best it can.
MFG - Manufacturing. This SPL supports more commands (such as rtask a)
jockyw2001 - Any Hard SPL made by jockyw2001 (WM6.1 versions)
cmonex - Any Hard SPL made by cmonex.
DaveShaw - Any bootloader patched by me. Will be the same as cmonex's because I copied her changes from previous versions - all credit to her .
Force USB - These SPL's have a fix to force the USB to work if it is not working for some reason.
nostuckinSPL - These SPL's have a fix to prevent you getting stuck at the bootloader as often.
Versions
Windows Mobile 6
-Hard SPL V1 (1.00.OliPof) [MFG] by pof / Olipro - Download and Instructions in the linked thread.
-Hard SPL V1.1 (1.1.JockyW) [MFG] by jockyw2001 - Download and Instructions in the linked thread.
-Hard SPL V1 nostuckinSPL Force USB [MFG] by cmonex - download only.
Windows Mobile 6.1 - All links are to the downloads, instructions to follow.
jockyw2001 (.hard)
3.07 Hard SPL / Force USB
3.28 Hard SPL / Force USB
3.29 Hard SPL / Force USB
3.56 Hard SPL / Force USB
cmonex (.hard2)
3.29 Hard SPL nostuckinSPL / Force USB
3.31 Hard SPL nostuckinSPL Force USB
3.56 Hard SPL nostuckinSPL / Force USB
DaveShaw (.hard)
3.34 Hard SPL nostuckinSPL Force USB
Instructions
If this is your first time flashing an SPL, take some time to read up on the other stickies (mskip's in particular) and wiki pages, this is more of a reference thread.
How to Install A Hard SPL:
Plug the device into your PC
Copy JumpSPL (either 1.56, 1.93 or 1.94) to your device.
Take out your SD card & SIM Card.
Run Jump SPL on your device
Wait for the bootloader screen to appear and "USB" to show.
Right-click activesync, go into connection settings and ensure Allow USB Connections is unchecked
Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
Run KaiserCustomRUU.exe and flash the SPL
If you have problems with the above process, try this:
Download the attached files from the first instructions
Pull out the battery and reinsert it (this step *is* important)
Connect your PC to phone with a USB cable
REMOVE SIM and SD CARDS !!
Copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe and if you still get a white screen then reset your device and now try JumpSPL1.94-KAIS.exe
After a few seconds "USB" appears on the phone display
Unplug and replug the usb cable
Deselect "Allow USB connections" in Activesync connection settings
Now flash hardSPL (run KaiserCustomRUU.exe on your PC)
Notes:
With the JumpSPL you should *not* flash radio roms, OS roms or full roms. The JumpSPL is only needed to flash a HardSPL (or SPL)
Upgrading SPL via SD Guide - Only works if you already have Hard SPL.
Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
Download the SPL you want to flash from the links above.
Rename the NBH file you downloaded to KAISIMG.nbh.
Download KAISDIAG.nbh from here.
Insert the microSD Card into the phone
Hold in the Power and Camera buttons, then press the reset button with the stylus for about 3 seconds until the BootLoader screen appears
It should say Loading / Update in progress and then to a screen saying SPL 1.00.OliNex
It should now say Press Power Button to flash or just flash the KAISIMG.NBH and then reset
At this point it should boot to the OS, if it doesn't then flash an OS (delete the previous KAISDIAG.NBH and KAISIMG.NBH from the SD Card and use Flashing Rom from MicroSD Card method)
After the Operating System loads, DELETE the KAISDIAG.NBH and KAISIMG.NBH files
FOR ANYONE WITH QUESTIONS ABOUT WHAT THIS IS FOR, WHY YOU WOULD NEED IT, OR HOW TO PERFORM SPL PROCEDURES: Read This Wiki page
FAQ (Not 100% applicable to this but a good source).
Thanks (in order of appearance)
pof
Olipro
jockyw2001
cmonex
Kyphur
mskip

I'm off home now I might not be back on for a while.
Post any problems here and I'll update / clean up this thread when I get home.
Ta
Dave

Very nice! Thanks for putting it all in 1 place!

Removed. I flashed 3-4 times and it finally took. Thank you for your help. Anyone else have a preference on a HARD SPL?

Hyden121 said:
Removed. I flashed 3-4 times and it finally took. Thank you for your help. Anyone else have a preference on a HARD SPL?
Click to expand...
Click to collapse
Was just about to reply. Glad you sorted it. I've had problems changing SPL before. The second set of instructions using Jump SPL worked. Also cmonex's KAISDIAG.nbh method works everytime.
I'm using 3.34 Hard SPL for 2 reasons.
1. The ROM I'm using is is based on the 3.34 ROM.
2. I made it (with cmonex's help ).
Dave

I saw that. I am using it as well but was curious if the 3.56 SPL was better in anyway. Either way it is great to finally have a new SPL and it only took me 1 year.

thanks dave! i've flased it and all seems well. my keyboards only have 2 keys you have to press a bit more firmly than the rest rather than 9 with 3.29 so that's much better!
had trouble flashing via customruu so did the microsd card thing. kinda weird though, last night, i couldn't get the microsd approach going with 3.29cmonex. so i flashed via customruu and it worked. now with 3.34, i couldn't get the customruu to work, so i did the microsd approach. anyway, so long as it works!

Thanks DaveShaw, you've really helped new-to-Tytn2 people like me a lot. A good beginning to the ROM experiencing journey

3.34 hardSPL tested ok for my kaiser,thanks to Daveshaw.

nice post, can anyone post his/her experience with the SPLs, meaning if better speed, battery life,....etc
thx dude

Could you explain what is the major advantage of using your 3.34 HardSPL toward to the other Hard SPLs?
I still have no idea about those HardSPLs differences so I'm using latest(? 3.54).
Thank you.

kurobosi said:
Could you explain what is the major advantage of using your 3.34 HardSPL toward to the other Hard SPLs?
I still have no idea about those HardSPLs differences so I'm using latest(? 3.54).
Thank you.
Click to expand...
Click to collapse
All Kaiser ROMs (Cooked or not) are based on a Official release (some cooked roms are based on more than one). Here's a list of the official releases: Kaiser ROMs.
You'll notice the version numbers are all 3.* for the WM6.1 ROM's. People have noticed if you are using the SPL version that matches your ROM version you get less screen freezes.
Sometimes you can't match them perfectly, so a little trial and error can help you find the best match.
Hope this helps.
Dave

DaveShaw said:
All Kaiser ROMs (Cooked or not) are based on a Official release (some cooked roms are based on more than one). Here's a list of the official releases: Kaiser ROMs.
You'll notice the version numbers are all 3.* for the WM6.1 ROM's. People have noticed if you are using the SPL version that matches your ROM version you get less screen freezes.
Sometimes you can't match them perfectly, so a little trial and error can help you find the best match.
Hope this helps.
Dave
Click to expand...
Click to collapse
great work dave but i have to ask something...
is there such a thing as the ultimate spl? meaning it's a bit troublesome to keep changing spl's based on the original builds of our cooked roms...since they keep coming from different sources...
from ur experience, which spl is the stablest with the newer cooked roms..
i've been using cmonex's 3.29 since it came out and to me it seems compatible with any rom i throw at it...
is ur 3.34 the new 3.29 hard2?

mazin13 said:
great work dave but i have to ask something...
is there such a thing as the ultimate spl? meaning it's a bit troublesome to keep changing spl's based on the original builds of our cooked roms...since they keep coming from different sources...
from ur experience, which spl is the stablest with the newer cooked roms..
i've been using cmonex's 3.29 since it came out and to me it seems compatible with any rom i throw at it...
is ur 3.34 the new 3.29 hard2?
Click to expand...
Click to collapse
No idea. I've been using it for a while now but I don't flash cooked ROMs much at the moment
Try it for a bit and it you like it keep it
Only cmonex knows what's going on inside the SPLs.
Ta
Daev

Great work dave, seems you are quite good in organising things, Was missing such a nice piece of thread & must have started had I been so much in to it. Thanks again. Good luck.

DaveShaw said:
There are now a large selection of Kaiser Hard SPL's floating about. I am making this thread as a collection for all of them and the instructions for flashing them.
MOD EDIT Snip...
Click to expand...
Click to collapse
Hi! I have weird problem with HTC Kaiser (or HTC TyTn II).
At the boot of Windows Mobile 6.1 i got the message "the device is clearing storage..." and then the device shutdown, the right led is stuck in blue and when I try to Upgrading SPL via SD my phone stuck at white screen and said loading...
I'm confused so I write this problem here. everything I do fails including mtty process. what can i do, help me please.
Thanks for advice.
Greetings!

neilus said:
Hi! I have weird problem with HTC Kaiser (or HTC TyTn II).
At the boot of Windows Mobile 6.1 i got the message "the device is clearing storage..." and then the device shutdown, the right led is stuck in blue and when I try to Upgrading SPL via SD my phone stuck at white screen and said loading...
I'm confused so I write this problem here. everything I do fails including mtty process. what can i do, help me please.
Thanks for advice.
Greetings!
Click to expand...
Click to collapse
Sound's like the ROM is at fault rather than SPL.
Try a hard reset, if that doesn't work, try flashing a new ROM via the bootloader.
Thanks
Dave

DaveShaw said:
Sound's like the ROM is at fault rather than SPL.
Try a hard reset, if that doesn't work, try flashing a new ROM via the bootloader.
Thanks
Dave
Click to expand...
Click to collapse
Hi Dave, thanks to reply, as I said I think I try everything and everything I do fails including mtty process, I try flashing a new AT&T ROM via usb cable at the BootLoader screen and the process completed 100% and when restart of Windows Mobile 6.1, I got the message "the device is clearing storage..." and then the device make a strange "sound" and shutdown, I was Tried a hard reset, doesn't work, I tried flashing a hardspl via the bootloader but unsuccessful, when I try to Upgrading SPL via SD my phone stuck at white screen and said loading.... when I try to Upgrading SPL via SD with the same SD to another phone its work.
Thanks.

@neilus,
Since Dave mentioned ROM issue, I suggest you re-download again the ROM (just to make sure you got it clean and good) and re-flash. What was your O/S or ROM before flashing? The SPL is important to match the ROM version .. if you're from 6.0, then you need to flash a ROM that comes complete with SPL (such as OEM upgrade ROM)
Otherwise, go back to starting point and read through the newbies guide and this (especially for your stuck on white screen)

anagarika said:
@neilus,
Since Dave mentioned ROM issue, I suggest you re-download again the ROM (just to make sure you got it clean and good) and re-flash. What was your O/S or ROM before flashing? The SPL is important to match the ROM version .. if you're from 6.0, then you need to flash a ROM that comes complete with SPL (such as OEM upgrade ROM)
Otherwise, go back to starting point and read through the newbies guide and this (especially for your stuck on white screen)
Click to expand...
Click to collapse
Hi anagarika, look this:
model : KAIS1*0
SPL-1.93.0000
CPLD-8
I was flashing a new ROM via the bootloader, original AT&T rom, everything work fine at the flashing process and finish 100%, when the unit charge and swich on going to first windows logo screen and with sound switch itself off (the sound is named "LB" I think).
Thanks a lot.