Is it me or is this part simply a peice of poor design and manufacturing?
How is it that hundreds of people and thousands of threads could have been produced by a "fit for purpose" bit of kit.
Is there nothing we as users can do to insist that the manufacturers recall and replcae these obviously fragile connectors.
O2 shop told me it was my fault and the damage was caused by "rough handling" but surely we can all of done this "rough handling" bit??
Are there any legal bods out there who can check this out???
:?:
i know its the XDA2's design because.......
how many posts have you seen......
XDA 1 connector fell off or spv connector damaged, spv e200 connector fell off......
well i can say ive seen none what so ever.
i just got my xda 2 back from my mate who had a go at putting it back on he done a good job but it doesnt charge with the house charger no more but does with the car charger so no worries i even put superglue all around the conenctor to make sure its not comming off again
there must be something we can do to get them sorted because its deffently a design fault
Actually it happens fairly often with XDA1s too. I've seen it happen a lot more frequently with XDA1s than with XDA2s but that could be because the XDA1 has been out a lot longer
I can replace connector!
I can repair/replace your broken connector in the UK. please get a qoutation today and I am garantee to goute you a 'happy' :lol:
[email protected]
cheers
Broken connector happened to my first I-Mate, for the record. Bad design I think.
I agree about the connector issue. My XDA I needed 'repairing' several times, before I just bought a new motherboard to replace it!
So far, my XDA II hasn't suffered the same fate, but I have learned to be VERY careful with that connector.
I am trying to take apart my htc pure. I cannot get the part down by the stylis to release. there is a small body part still in place after removing the battery cover and the torx screws. has anyone taken one of these apart willing to give me a hint?
thanks in advance for any clues
got it apart. turns out there is a little plate just under the front nav buttons (will post pics later if possible) that needed pried off to reveal 2 other screws. I got the speaker to work, kind of. it has a lot of crackle to it. now I have a few questions I am not sure on.
how can I tell if the unit has previously been modded, should I search the rom revision on the forum?
if it has been modded, possibly just a bad radio file has been loaded, I kinda doubt that but could that be possible?
lastly, does anyone have any idea where to purchase a replacement ear speaker? I have searched high and low. only found one new they wanted $85.00 for just the speaker. Gee, little high.
I have seen dead units on ebay for $40.00, thinking that may be my only option now.
I got my wife a used LG Quantum off of eBay because she wants to switch from BlackBerry. I got a new OEM battery and battery cover so it looks pretty new. The problem is, the touch screen does not work. My question is, should I just re-sell it on ebay to get my money back (I bought it for $51), or should I spend the $35 on a new touch screen digitizer and fix it myself?
I guess it depends on your skill set. Personally for $51 for a Non-Contract phone, you can't beat the price even after spending an extra $35 to get a mint phone.
If you can handle the tiny screws and ribbon cables, it can be tricky with lots of tiny parts, then go for it.
I'm pretty handy when it comes to PCs and general tech stuff, I replaced a digitizer on a HTC Touch Pro for the hell of it. It took me about 2 and 1/2 hours. That was with laying everything out on a clean table, and taking digital pictures along the way, incase of any questions when putting it back together.
Good luck if you decide to take it on.
DavidinCT said:
I guess it depends on your skill set. Personally for $51 for a Non-Contract phone, you can't beat the price even after spending an extra $35 to get a mint phone.
If you can handle the tiny screws and ribbon cables, it can be tricky with lots of tiny parts, then go for it.
I'm pretty handy when it comes to PCs and general tech stuff, I replaced a digitizer on a HTC Touch Pro for the hell of it. It took me about 2 and 1/2 hours. That was with laying everything out on a clean table, and taking digital pictures along the way, incase of any questions when putting it back together.
Good luck if you decide to take it on.
Click to expand...
Click to collapse
I'd say I'm pretty handy, I've just never worked with anything that delicate. I figured I have nothing to lose since she still has her BlackBerry so there's no pressure.
I looked up videos on it and it seems to not be that hard. If replacing the digitizer on the TP wasn't that hard, just time consuming, then the Quantum seems like it should be even easier.
Thanks for your input. I think I'll go for it.
please take picture EVERY part you dismantle so that you won't miss a step.
Just my 2 cents.
Ttblondey said:
please take picture EVERY part you dismantle so that you won't miss a step.
Just my 2 cents.
Click to expand...
Click to collapse
Excellent point. I do have a tendency to forget what I just did 2 seconds ago and what everything looked like before I started.
Just a quick update. I received a brand new OEM digitizer today and replaced it with the non-responsive one on the phone. It was extremely easy and took me around 20 to 25 minutes.
Thanks for your suggestions guys.
Hey all. I have no sound. Zero. I tried re-flashing zeus - no go. Tried clearing/resetting everything via cwm - nope. I tried GTG twice - nada. Even back at stock, I've got nothing. I can hear my voicemail, but no system tones, no ringtones, no audio on videos - both youtube and local to phone. Alarms won't work. Nothing!!
After pouring over these threads, I tried headphones, and they work - but no headphone icon at top of my screen. I'm at my wit's end and am pulling out my hair. Does anyone have any ideas? Please?
Start with the simplest solution first. Is the media volume turned up? btw I don't have a headphone icon either but I'm not sure it had one to start with.
Running Zeus 6 also.
~wolverine~ said:
Start with the simplest solution first. Is the media volume turned up? btw I don't have a headphone icon either but I'm not sure it had one to start with.
Running Zeus 6 also.
Click to expand...
Click to collapse
uhhhh, yeah. I've checked all the sounds like 80 times - After each restore, reload, refresh, reboot, re-flash to stock, re-wipe, re-unameit. lol
I just hope it's not hardware related, although if it were, I'd think I'd have had to change something or move something that I hadn't. I just removed my ext sd card about 15 minutes ago, but nothing there either.
the best hope that you will have if it's not hardware related:
take out microsd card.
factory reset from /settings/privacy/reset
heimdall 1 click with repartition and bootloaders
do it twice for good measures
run the complete stock rom...
if that doesn't work, it may be hardware corrosion
I hav had this happen believe it or not i just gave the phone a slight twist holding it at the ends...sounds funky not a hard twist...but i got my sound back..i keep it in a ballastic case now...my infuse is a lil older and has seen to much desert heat...
True story...
Sent by Aeon (bigfau's) Awesomeness via me !
OK, y'all. I've got news and info on this issue. After trying everything possible short of throwing it into the river, I figured it was def hardware related. I, of course prayed & am convinced that is the real reason it started working, bit jic here is what I did. I checked online just to see (I'm not an idiot, I wasn't going to take it apart. Well, probably not). But I was still all for slapping and twisting and flicking the heck out of it. Then, I decided to look at the other side of it. So I removed the battery and there is a tiny little slit-like hole there. I got out a safety pin and just kinda wiggled of a bit mostly toward the inside of phone. Lo and behold sound was working when I turned it back on. I can't believe it! I'm so happy!
Sent from my SAMSUNG-SGH-I997 using XDA
EDIT: It's easier to type on PC than on phone, so now I can make a short story even longer. haha. I should mention that this could be risky if done wrong, if that's not obvious for some people, and could screw your phone even more, so BE CAREFUL!!!
I'd consider using something flat enough to get in there, but not as sharp as a pin. I was just Macguyver-ing it. You do have to remove the batt cover, but don't need to take the batt out to get to the slit, but you may want to - in case of interference from metal pin and whatever. To be more specific to where this is: the external speaker is located on the backside of the phone - bottom, left. Duh, right?
Also, take this time to clean out any dust/crud that may have gathered in the tiny little cracks and corners, which accumulates more for those of us that remove the batt cover often, like putting phone in DL mode and such. Don't use alcohol or anything - this is a good place to use the pin or needle, and especially blow on it.
At one point, I had phone on and video going to gauge whether anything I was doing specifically was working or not. I never got sound to work that way, but it's still a plausible idea for someone else to try. Anyway, I hope this helps someone else out there. I like to include as many details as possible when I post stuff b/c it helps me when others are specific. So, let me know if this was helpful to you and good luck!
dde333 said:
OK, y'all. I've got news and info on this issue. After trying everything possible short of throwing it into the river, I figured it was def hardware related. I, of course prayed & am convinced that is the real reason it started working, bit jic here is what I did. I checked online just to see (I'm not an idiot, I wasn't going to take it apart. Well, probably not). But I was still all for slapping and twisting and flicking the heck out of it. Then, I decided to look at the other side of it. So I removed the battery and there is a tiny little slit-like hole there. I got out a safety pin and just kinda wiggled of a bit mostly toward the inside of phone. Lo and behold sound was working when I turned it back on. I can't believe it! I'm so happy!
Sent from my SAMSUNG-SGH-I997 using XDA
Click to expand...
Click to collapse
good job.
to help other misfits, you can change the title of your op to [SOLVED] ..etc...
Some clarification on repairing speaker / restoring power
This is a great post and worked for me so I wanted to clarify some more detail.
Diagnosis: My external speaker would not work or work intermitently. I could hear on my handset and headphones but could not use speaker for conversations, media, etc.
I tried reseting with/without power on.
Tried factory resetting the phone.
Tried "headphone sex" (removing headphones in and out quickly as the software may have a glitch where it does not recognize the headphones were removed hence restoring external sound to the speaker) This is NOT a common problem with the Infuse but with other Samsung phones like the Captivate I believe.
After many people having similar symptoms I saw this post and figured it was a power issue/hardware not software problem.
Previous post....
1. I could not find a small hole to put a safety pin through (as previously posted). I used a paperclip as it is less pointy and less damaging and there wasn't a single hole to put it through.
MY RESOLUTION/REPAIR THAT SOLVED THE PROBLEM (same issue just different way to fix as I did not find any hole to put a pin through)
2. you will need to remove the back cover of the phone. Remove the battery cover, battey, sim card, and ext SD card. There are 6 small jewelry type screws. You should have an eyeglass kit screwdriver or jewelry kit with small screwdrivers. I did manage to use a small regular screwdriver but it really did not fit and could strip the heads of the screws.
3. Once the 6 screws are out, remove the back cover of the phone. Mine was a little hard to remove. The top is the earphone jack and the cover goes over the earphone jack, so great care should be made to try and take the top off last. For mine, the side was easiest to remove first( in the middle). Little by little you should be able to work your way around the edges until it is all separated from the screen/front.
*TIP Do not worry about parts coming out. The back cover is secured with the 6 screws. The rest of the phone and boards are screwed down to the front/screen so all you are doing is removing the back cover.
4. Once the back cover is separated from the front/screen, locate where the speaker lies in the back cover and where it comes to meet the front/screen. You will see two small gold square tabs on the back of the back cover next to the speaker. If you look where these connect to the front/screen you will see another two small gold tabs. These ones are NOT flat. They actually sit up and are hinge like. ***THIS IS WHERE THE PROBLEM IS****.
5. As the phone ages and gets used aka banged dropped wet, etc, these tabs lose their "springyness" and pressure so they get flat and fail to contact the other tabs next to the speaker, resulting in no power getting to the speaker or intermitent power as they make contact. THIS IS WHY IF YOU READ OTHER POST ON OTHER FORUMS YOU WILL SEE PEOPLE SAYING THUMPING OR PRESSING ON THE SPEAKER MAKES IT WORK INTERMITENTLY!
6. Get a pair of tweezers and slide one side of the tweezers between one of the small gold tabs on the front/screen side of the phone. BE CAREFUL! The tabs are very small thin and fragile so go slow and make sure you are between where the tab mounts to the circuitboard and where it sticks up to contact the speaker tabs. SLOWLY work the tab up so that you restore the arch or springyness back to it. It should look like this <. Do the same for the other. Basically you are raising the tab so that when you put the back cover on it makes contact with the speaker tabs, hence providing the proper power to the speaker.
7. Put the cover back on, screws, ext SD card, sim card, battery, and batter cover back on. Power up and adjust your ringer volume. You should here the speaker working.
Awesome. I'm glad my post pushed you in the right direction and am certain your post, with more details, will be helpful to others in the future. Phones are so much better with sound, aren't they? :highfive: Have a wonderful weekend.
I also had the problem of no sound at all, but the head phones worked flawlessly. In my case this is what it was (don't laugh) I ordered a replacement body for my phone for like ten bucks on ebay, pulled the old one off...replaced the housing and everything SEEMED to work just fine. I really didn't notice that my phone was not making any sounds until about a week later and just figured that maybe I had installed something that was conflicting with the phone or simply needed to re-flash the ROM, so I went and did just that and nothing seemed to work. Back to stock....NOTHING...New kernel...NOTHING!! I was becoming hopeless at this point till I read this thread. I had to think back to when (I think) it stopped making any sound and could only come up with the day I replaced the housing, so I retraced my tracks. LOL and what I came up with made me chuckle a little, what had happened was when I took the old back off I did not notice that the speaker is highly camouflaged near the bottom of the housing and simply needed to be snapped out and snapped back into the new housing. After this.....VIOLA..SOUND! So, maybe this can help someone that may be having the same issue and just cannot get to the bottom of it..
Thanks XDA and its members:good::good::good::good::good:
No Sound On Infuse
bigjoe2675 said:
I hav had this happen believe it or not i just gave the phone a slight twist holding it at the ends...sounds funky not a hard twist...but i got my sound back..i keep it in a ballastic case now...my infuse is a lil older and has seen to much desert heat...
True story...
Sent by Aeon (bigfau's) Awesomeness via me !
Click to expand...
Click to collapse
I have to say that this method worked like a dream for me. I couldn't believe it when I tried it. I went to "settings" -> "sound" -> "volume" -> "Incoming call volume" and then adjusted it so it would make a sound. No sound was being made but I knew it should have been so I grabbed the top and bottom and slightly gave it a little twist, just barely and the ringtone came right on and has been working perfect since. The Infuse I have is 99.9% mint condition, never been dropped and has always been inside a leather case with a full fold over front. Not even a hair line scratch on the screen, back, sides or anywhere. This is why I couldn't understand why the sound just decided to go out for no reason but anyway, this fixed it and a big thanks to "bigjoe"! I thought I was about to have to buy a new phone because I can't hear (vibrate) more than a foot or so away.
Solution - Twist
Judge Joseph Dredd said:
I hav had this happen believe it or not i just gave the phone a slight twist holding it at the ends...sounds funky not a hard twist...but i got my sound back..i keep it in a ballastic case now...my infuse is a lil older and has seen to much desert heat...
True story...
Sent by Aeon (bigfau's) Awesomeness via me !
Click to expand...
Click to collapse
Thanks for this info. I had lost a lot of volume. After reading your post, I tried the twist thing and bingo, it worked. Thanks very much.
Judge Joseph Dredd said:
I hav had this happen believe it or not i just gave the phone a slight twist holding it at the ends...sounds funky not a hard twist...but i got my sound back..i keep it in a ballastic case now...my infuse is a lil older and has seen to much desert heat...
True story...
Sent by Aeon (bigfau's) Awesomeness via me !
Click to expand...
Click to collapse
SHUT THE FRONT DOOR.... - just twisted my cell and BAM....sound I LOVE YOU!!!!! XOXOXOXO awesomeness indeed
Wow!
parkerhawn said:
SHUT THE FRONT DOOR.... - just twisted my cell and BAM....sound I LOVE YOU!!!!! XOXOXOXO awesomeness indeed
Click to expand...
Click to collapse
I just gave my infuse the twist and the sound is back!! Insane! PS. I could always hear my sound but it was so faint I had to put my ear up to the speaker before I could actually hear the sound!
This actually works!
thomasmaio said:
This is a great post and worked for me so I wanted to clarify some more detail.
Diagnosis: My external speaker would not work or work intermitently. I could hear on my handset and headphones but could not use speaker for conversations, media, etc.
I tried reseting with/without power on.
Tried factory resetting the phone.
Tried "headphone sex" (removing headphones in and out quickly as the software may have a glitch where it does not recognize the headphones were removed hence restoring external sound to the speaker) This is NOT a common problem with the Infuse but with other Samsung phones like the Captivate I believe.
After many people having similar symptoms I saw this post and figured it was a power issue/hardware not software problem.
Previous post....
1. I could not find a small hole to put a safety pin through (as previously posted). I used a paperclip as it is less pointy and less damaging and there wasn't a single hole to put it through.
MY RESOLUTION/REPAIR THAT SOLVED THE PROBLEM (same issue just different way to fix as I did not find any hole to put a pin through)
2. you will need to remove the back cover of the phone. Remove the battery cover, battey, sim card, and ext SD card. There are 6 small jewelry type screws. You should have an eyeglass kit screwdriver or jewelry kit with small screwdrivers. I did manage to use a small regular screwdriver but it really did not fit and could strip the heads of the screws.
3. Once the 6 screws are out, remove the back cover of the phone. Mine was a little hard to remove. The top is the earphone jack and the cover goes over the earphone jack, so great care should be made to try and take the top off last. For mine, the side was easiest to remove first( in the middle). Little by little you should be able to work your way around the edges until it is all separated from the screen/front.
*TIP Do not worry about parts coming out. The back cover is secured with the 6 screws. The rest of the phone and boards are screwed down to the front/screen so all you are doing is removing the back cover.
4. Once the back cover is separated from the front/screen, locate where the speaker lies in the back cover and where it comes to meet the front/screen. You will see two small gold square tabs on the back of the back cover next to the speaker. If you look where these connect to the front/screen you will see another two small gold tabs. These ones are NOT flat. They actually sit up and are hinge like. ***THIS IS WHERE THE PROBLEM IS****.
5. As the phone ages and gets used aka banged dropped wet, etc, these tabs lose their "springyness" and pressure so they get flat and fail to contact the other tabs next to the speaker, resulting in no power getting to the speaker or intermitent power as they make contact. THIS IS WHY IF YOU READ OTHER POST ON OTHER FORUMS YOU WILL SEE PEOPLE SAYING THUMPING OR PRESSING ON THE SPEAKER MAKES IT WORK INTERMITENTLY!
6. Get a pair of tweezers and slide one side of the tweezers between one of the small gold tabs on the front/screen side of the phone. BE CAREFUL! The tabs are very small thin and fragile so go slow and make sure you are between where the tab mounts to the circuitboard and where it sticks up to contact the speaker tabs. SLOWLY work the tab up so that you restore the arch or springyness back to it. It should look like this <. Do the same for the other. Basically you are raising the tab so that when you put the back cover on it makes contact with the speaker tabs, hence providing the proper power to the speaker.
7. Put the cover back on, screws, ext SD card, sim card, battery, and batter cover back on. Power up and adjust your ringer volume. You should here the speaker working.
Click to expand...
Click to collapse
-----------------------------------------
Thank you so very much, it helped a lot to follow your directions. I realized how hard it is to remove the entire cover so I used a very small flat screw driver (eye-glasses kit) and popped open only the bottom corner where the speakers were. I could then see the hinged-like tabs and used one hand to keep the cover from snapping back shut and the other hand to "raise" the hinged side of the tabs using the same tiny flat screw driver. I raised them high enough (gently) and put the cover back in place. I then put the battery back, turned on the phone and Voila! Sound is crisp and clear once again.
I've had my Nexus 5 for over 3 years now and it has seen countless ROMs, Kernels, rooting, all that kind of stuff. I also bought it in white and decided after some time that I want a black one so I bought a frame and a back panel and moved everything over to the new assembly. Shortly, it has seen a lot of mods.
My father used it for some time and one day he droped it and the microphone didn't work anymore in calls.
The problem was simple: in calls or while recording audio on whatsapp and such, the mic didnt work. While playing back the recording, there was a slight noise, just as you would keep the record button pushed but not talk and let it record only background noise. I can't remember, though, if while in call and on speaker the mic worked.
I bought a used flex cable with mic, charging port and everything on it (of which I was told was new), switched the old one with it and while playing back the recorded audio you can hear an awful distortion with slight oscilations as where the words should fit in.
However, the other person can hear me while in call and on speaker, but the sound is very, very bad.
My guess is that the mic on the flex cable that I bought was broken as well.
I thought of going ahead an buying another flex from a more trusted seller, but I'd like to get some advice firstly.
I tried anything that could be done with the software, this clearly is a hardware problem. What do you think I should check? What could be broken besides what i already know?
Thank you and have a lovely day!
I don't know if this will help but this guy seems to have a similar problem you can try his solution.
https://www.google.com/amp/s/forum....nexus-5-microphone-speakerphone-t3043151/amp/
Sent from my Google Nexus 5 using XDA Labs
Hey!
Audio rec and calls use different microphones, however, I believe your problems are due to the connector slot on the PCB itself not due to flex cables. Just visually inspect your flex cables, do you see any strong fold lines or torn sections? If not it is quite unlikely.
Regarding the connector slot, find some repairmen who is able with a heat gun and flux, who can lift things from a pcb without damaging stuff. They can either reposition it or replace it.
Best of luck and I completely share your pain.
andreizet96 said:
I've had my Nexus 5 for over 3 years now and it has seen countless ROMs, Kernels, rooting, all that kind of stuff. I also bought it in white and decided after some time that I want a black one so I bought a frame and a back panel and moved everything over to the new assembly. Shortly, it has seen a lot of mods.
My father used it for some time and one day he droped it and the microphone didn't work anymore in calls.
The problem was simple: in calls or while recording audio on whatsapp and such, the mic didnt work. While playing back the recording, there was a slight noise, just as you would keep the record button pushed but not talk and let it record only background noise. I can't remember, though, if while in call and on speaker the mic worked.
I bought a used flex cable with mic, charging port and everything on it (of which I was told was new), switched the old one with it and while playing back the recorded audio you can hear an awful distortion with slight oscilations as where the words should fit in.
However, the other person can hear me while in call and on speaker, but the sound is very, very bad.
My guess is that the mic on the flex cable that I bought was broken as well.
I thought of going ahead an buying another flex from a more trusted seller, but I'd like to get some advice firstly.
I tried anything that could be done with the software, this clearly is a hardware problem. What do you think I should check? What could be broken besides what i already know?
Thank you and have a lovely day!
Click to expand...
Click to collapse
keoxkeox said:
Hey!
Audio rec and calls use different microphones, however, I believe your problems are due to the connector slot on the PCB itself not due to flex cables. Just visually inspect your flex cables, do you see any strong fold lines or torn sections? If not it is quite unlikely.
Regarding the connector slot, find some repairmen who is able with a heat gun and flux, who can lift things from a pcb without damaging stuff. They can either reposition it or replace it.
Best of luck and I completely share your pain.
Click to expand...
Click to collapse
Thank you for your answer. I know I'm replying after almost one year, but I have given up fixing the old Nexus. Maybe I will try opening it up again and checking what you said, but I don't think it is worth it anymore. I still power it up from time to time, just for the old days. Heh. ?