Wiazrd stops duing Initial Progrm Loader - 8125, K-JAM, P4300, MDA Vario ROM Development

To beguine i wont to thank all of you for making this forum possible. After hardSPl device and installed Wizard Love ROM i was trying to install kitchen ROM After i tryed Hard REseting it didnt ask me to tap Yes but just restarted and from now on i can se just the IPL Screen of Wizard Love With IPL 2.21.0001 SPL2.21Olip GSM 02.5.11 and OS 10.0.0.10 is this a BRICK meaning i downlded a wrong ROM by mistake and How can i get this running the ActiveSync Wont Connect in this mode and how can i get to bootloader screen thout a stylus my GF Lost it
Thnx

Oh, please try to write it slowly
Try holding your camera button and resetting. If it will enter a tri-colour mode (bootloader), it's alive. Just flash it again.

did you make that rom?
if so, it may be unicode rgu problem, imo.
if not, you made sth wrong..
if it is g4...oops.

sirtux said:
To beguine i wont to thank all of you for making this forum possible. After hardSPl device and installed Wizard Love ROM i was trying to install kitchen ROM After i tryed Hard REseting it didnt ask me to tap Yes but just restarted and from now on i can se just the IPL Screen of Wizard Love With IPL 2.21.0001 SPL2.21Olip GSM 02.5.11 and OS 10.0.0.10 is this a BRICK meaning i downlded a wrong ROM by mistake and How can i get this running the ActiveSync Wont Connect in this mode and how can i get to bootloader screen thout a stylus my GF Lost it
Thnx
Click to expand...
Click to collapse
Nopes !
Its not a Brick,just a bad flash.get it in bootloaders mode by pressing and keep holding the 'Camera' button and push the 'Power On' button,it'll go into bootloaders and flash the wizard_love rom again,hope it'll recover back.
And for god's sake get a new stylus,keep it away fgrom your GF

sirtux said:
To beguine i wont to thank all of you for making this forum possible. After hardSPl device and installed Wizard Love ROM i was trying to install kitchen ROM After i tryed Hard REseting it didnt ask me to tap Yes but just restarted and from now on i can se just the IPL Screen of Wizard Love With IPL 2.21.0001 SPL2.21Olip GSM 02.5.11 and OS 10.0.0.10 is this a BRICK meaning i downlded a wrong ROM by mistake and How can i get this running the ActiveSync Wont Connect in this mode and how can i get to bootloader screen thout a stylus my GF Lost it
Deleted
Click to expand...
Click to collapse

Related

HELP! MDA wont boot after update!

I tried to install the faria wm6 update with the shelltool. everything was going as per the directions when about 3 or 5 mins in the the install process it gave me an error on the phone saying something about the reprog.exe or someting... anyways, the computer said done and to reboot... so I did and now it goes as far as the white TMOBILE screen with the following 4 lines of code
IPL 2.26.0001
SPL 2.26.0001
GSM 02.25.11
OS 2.18.0.0
and it freezes there... it wont turn off either.
Tries removing the battery and reinserting it. Well the same thing happens upon powering on the device. Tried hitting the little hard reset button on the side with the stylus... the screen flashes off and then it attempts to reboot again and the phone freezes at the same spot. Please help. I did everything according to the directions. PLEASE TELL ME I DIDNT BRICK MY PHONE. :'(
Can you get into bootloader mode? If so then its not a brick. Try to go to bootloader mode by holding down camera and voice commander button while powering on. Then reflash your carriers rom or wizard love.
edit:stop double posting your problems there is no need.
Read and follow this:
http://forum.xda-developers.com/showthread.php?t=298613
bwesty said:
Can you get into bootloader mode? If so then its not a brick. Try to go to bootloader mode by holding down camera and voice commander button while powering on. Then reflash your carriers rom or wizard love.
edit:stop double posting your problems there is no need.
Click to expand...
Click to collapse
sorry, I was in a panic and I couldnt search and find a solution fast enough so I posted the question here and in wizard fourm... thanks though. Got my old rom back... now time to try it again.

i think i have brick my dopod 818pro.. Please help

i think i have brick my dopod 818pro
have follow the step 1 and install without any error.
then installed the Cert_SPCS.cab and EnableRapi.cab.
then installed the Prophet_4.0.0.0.1_PV rom by running Upgrade_ROM.bat from the computer.
after that restat the device.
AND the phone boot after the HTC Innovation screen and stay at the loader screen.
NOw my screen only showing :
IPL 2.15.0001
spl 2.15.0001
gsm 02.69.21
os 4.0.0.0
and wouldn't boot in ???
anyone here please help
tq
finnally manage to boot in.
redo the step 1 in boot loader mode.
then installed the pdaviet 4.0.0.0.1 from pc
and it is done.
very nice screen
will try it out n c .
tq very much
Hi, how did you manage to solve the issue?
My situation is a little different.
-Load Step 1... ok Successful
-Load Upgrade_Rom.bat... completed
But when I reboot the PDA I just get this screen!!!
Nothing is responding.
PC cant detect the device.
Hard reset also get back to the same screen.
Please help
reboot your device into the bios screen (reset while holding camera button)
at that point i usually just put on the default WM5 comming from QTEK to reestablish operations.
i am using the prophet touch series from gullum and for that i do the following steps after having reestablished the WM5.
Put on PDAViet_TEMP
wait until phone restarts and shows 'Touch to get started'
Put on the Prohvet Touch (VIII or IX Beta)
Hard Reset (Com and Cam button, wait for the message asking to confirm afetr you release the reset button but hold on to com and cam buttons until message pops up) Confirm Hard Reset
So far i repeated this process about 6 times and it works every time
best of luck
need explanation
im planning to buy a dead prophet.....as the seller states...when he posted the pic, it still enters bootloader mode...but it shows
IPL: 1.00
SPL: 2.20.0001
Can this still be repaired? and is this possible? how can i repair it...it is being sold at a very cheap price
I've had similar issues and by just putting the original rom or the WM5 if you can enter bootloader mode thenit comes back to live. Once WM5 which is very stable is loaded, you can upgrade to the WM6 roms. Has always worked for me but it is a bit nerve racking to see the thing frozen. The key when upgrading is to use than WM5 rom and upgrade from there.

need some help

hello,
I've tried to install skype ona my cingular 2125 and now it doesn't work.
the phone just stuck on .cab extractin screen and i restart it.now the only thing it show is the cingular startup screen and that's all.I have the cingular rom update uttility but it says that the device is not connected to the pc using usb,and ask me to check the connection.
what i can do about this issue?can anyone help me?
thank you in advance
Try turning off USB connection in activesync. With the phone turned off, if you hold the camera button when you plugin the usb to phone (already connected to PC), it should start up in the bootloader.
Other method to get the bootloader is to hold the camera and the comm manager button and turn on the phone.
You should be able to use the ROM update utility with the bootloader.
Look at Karhoe's guide in the stickies at the top of this forum...
Maybe hard reset will be enough ?
Turn off Your phone. Press and keep hold of both soft keys, press the power button for approximately 0.5 to 1 second, phone will ask U if U are sure, press 0.
hard reset is a lot safer than reflash...
i can't believe
thank you for all the advises but unfortunateli non of them helps.I've trie everything and it still shows cingular's wellcome screen and that is all.after that the only thing i can do is to remove the battery because nothing else work.I put the original rom from cingular and everything was OK with the setup, but after that -the same.I've tried with this hard reset- the same.probbably the nezt thing that i will do is to hit it into the ground )
mi4 said:
I put the original rom from cingular and everything was OK with the setup, but after that -the same.
Click to expand...
Click to collapse
Missunderstanding here
Our goal was making Your phone alife again.
None of mentionated procedures could help with some unknown to us bug in Your version of 3-rd party software
The latest skype works perfectly for me, in WM5 and WM6, since you are going to hard reset, why not perform a WM6 upgrade?
re
I was tried to reflash with the original aku2 rom from htc/cingular (the flash was successfull)but after that the phone is still not working.allways the same- cingular's startup screen and that's all.also try with hard reset with no success.I doubt that this phone will ever work again.or if there is another way to "clean" the whole memory?!is it possible to hardware reset the phone?
Format BINFS and reflash, that will clean everything except the IPL and SPL

May some one help this poor man!!

i hope u answer my request !
i found u the smartest person in this forum !
i have jamin after upgrading from a k-jam rom
it cuts in the middle of the uprade!
when i turn it on the LCD flash for one second
and then turn off
also i cannt enter bootloader to flash another rom
now my jamin is completely dead
hope to help me i am only a starter
well 24 views and no reply
plz guys dont let me down
Is your battery is well charged when the screen was flashing and turning Off ?
100%100 yes my battary is comletely ful
Why on earth did you try to flash a Jamin with a K-jam rom?
Are you able to get into bootloader ie. hold down the COMM button and press the soft reset?
If you can get into the bootloader your phone can be saved, and I would advise you to have a deep read of the WIKI page.
Dixiesmu said:
Why on earth did you try to flash a Jamin with a K-jam rom?
Are you able to get into bootloader ie. hold down the COMM button and press the soft reset?
If you can get into the bootloader your phone can be saved, and I would advise you to have a deep read of the WIKI page.
Click to expand...
Click to collapse
Try Doing Hard Reset by Pressing camera, comm manager, power & soft reset button.
if successfull then try entering bootloader mode.
Thanks.
try removing the battery n hard reset ...... connect it to pc n sync(if device do not go to bootloader directly) download bikertibi's ROM
flash it......
REMEMBER use hard spl for ur version(g4 or g3) be4 flashing .....
if it directly goes to bootloader let me know
don't wry....... cheers!
Aju
the same problem with my prophet
i sent twice in the forum once in this topic
http://forum.xda-developers.com/showthread.php?t=319636&page=3
after going with the steps in it without any result
and once in a separate topic
http://forum.xda-developers.com/showthread.php?t=632446
without any response till now
i hope some one here in this topic can help?
Cutten USB works only for the g3 chipsets...
Well just connect to pc by USB and make it in bootloader

Htc TOuch Pro Stucked on Startup

i've already did a research.
Manage to Go bootloader.
But i cant seem to reflash my rom.
Stuck at 0% and theres an eror that came out.
It's strange.
For the first attempt it was a sucess and i managed to stock the Original SPL
So after doing that i tried the Hard-SPL.
Stuck at 0% eversince.
What phone do you have?
GSM or CDMA?
For almost if not all ROMs here you MUST HAVE hardSPL!!!
Oh i did have rom previously.
And i wanted to try lunacieROM
so i did flash it.
and it's stuck on the Black Screen after sucessfully reflashing.
So i went to the bootloader.
Reflash the Stock SPL
and wanted to reflash the Hard SPL
but it failed.
Its GSM.
Don't know why you flashed back to a stock SPL but I assume after flashing to a stock SPL you should FIRST flash your (or a) stock ROM and start from scratch (stockSPL --> hardSPL --> new ROM).
the problem is
after goin back to stock spl.
i dont think i can flash other roms.
including hard spl
or any other roms.
any idea?
And it get stuck at 0%
everytime i try to hard spl.
thats the thing thats been bothering me.
rullly said:
And it get stuck at 0%
everytime i try to hard spl.
thats the thing thats been bothering me.
Click to expand...
Click to collapse
What PC do you have (OS)?
You get a reliable active sync connection?
Did you try to put the phone into bootloader mode (tri-color screen) while DISCONNECTED from USB - will read "serial" at the bottom of the screen- and connect USB while in tri-color screen - should change to USB?
That are some basics to check and to test.
You COULD try to connect the phone in storage mode that it forces your PC to install Qualcom USB/NDIS drivers.

Categories

Resources