I have been asked to replace a broken screen on a T-Mobile phone. The only id I can find for the phone is HTC PM200. I think this may make it a HTC Charmer or MDA compact II. I only think this is correct hence the reason for the post in the general forum. (Mods can you move to appropriate). Any way the screen was cracked and I have replaced it with the same model(taken from the rear of the screen). The phone boots up correctly but refuses to recognise any taps on the screen. I have downloaded remote screen alignment but this had no effect. Any body any ideas if I have done something wrong or ways to fix this problem. The screen code is LTP280QV-E01. I have searched the forums hence the reason for downloading "Remote Screen Alignment"
Thanks in advance
Related
Hi,
I've just received my TyTN today and I'm not very satisfied concerning the touch screen.
I don't know what is happening but the touch screen does NOT respond properly. I've tried to clean it a bit, but the result remains the same.
When I want to use the screen keyboard, it's horrible. I point the letter A and the screen understands that I'm touching the letter under or the letter just near the "A". It's pretty impossible to write a text properly and very hard to open programs or browse with the touch screen.
Of course I've tried to align the screen. It's working without any problem then.
But after some times, opening apps, closing others (using normally the pda inf act), the problem comes back... the TyTN does't really understand where I'm touching the screen.
Then I make a screen alignement, and it's working back... It's just amazing
I don't think it's a hardware problem because the alignement is working after an align screen.
Maybe it's a known error ? Has somebody the same problem ??
Is there a rom update to fix that ? Or is it a problem of my own HTC ?
Thanks !
Can you help me please ?.
Hi,
I don't have this issue with mine...
Check the "TnTN/v1604 problem" topic maybe
I had the same thing, once, with my variO. Probably I pushed too hard onto the screen while cleaning.
Actually, this is a known problem with some of the first shipment devices. Look at the other TyTn topics i this forum.
Hi i recently got this htc p3600 with broken touchscreen, the lcd is fine but the touchscreen have some cracks in it.
I don't know anything about what versions of roms etc is in it. All i know is that windows mobile's in it.
When i start up the phone i get a green windows mobile screen witch says that i should click anywhere on the screen to calibrate the screen. I do htat because i can't do anything else and then this X shows up and i am suopposed to click on it in order to calibrate the screen.
I'm doing this, first in the middle then it moves to each corner but when i clicked all the corners i goes back to the middle nad starts over agaiN!!
I've clinged this stupid X for like 15 minutes now but nothing seems to happen!! Whats the problem? Can it be locked to the sim-card i've inserted??? Please help me!
guess you will have to replace the digitizer.othewise, you may try connect it with active sync and delete the call program from auto run - hopefully theres some default cal data in it.
Don't really understand what you're saying, im new to this phone and i got i broken. ALready ordered a digitizer but i want to test it out now. Tried to add a calibration value to the registry but i cant do anything because its locked.
So i think enableing rapi will o the trick but i cant start the phone to start the enable rapi program :/:/
Is there any other way to bypass this screen? Like killing the process with some taskmanager??
go search for remotecalibration.exe
hello
i got my polaris for 3 days: everythig ok until i applied the screen protector (i think there started my problems):
first simptom - touch screen with response problems, than not working at all! (yes i removed the screen protector)..i hoped that maybe it is a software problem.
i have tried using it with the buttons - manged to lock the keypad
so after searching the net i found the way to "hard reset"...but that needed both gps and IE buttons pressed.... locked
Next step: i found this forum ..searched for any similar problems..no luck
Tried to flash the ROM using both bepe and udK (bittdefender found "Trojan.Qhosts.AQP" in udK release ) tools. Both tools stucked at 0%.
Another tool needed EnterBootloader.exe to run on my PPC. but without keys/pen i could not install it, so i put the a command for program in my Startup tasks on the PPC.
Now the ppc starts and then goes in the 4 colour mode. I'd tried to install/flash the ROM again..no luck stucked at 0%.
Can anyone help me?? could it be a software problem? or maybe it.s a hardware problem. (i gor no response from the touch screen since)
Thanks!
P.S. Sorry for my english..hope u understand my problems
One question: did you use water or something else to place the screen protector on your device?
Return it asap!!
I used some glass cleaner (foam)..but the screen was dry and clear when i put the protection.
The phone is in service now...(repair..if not a new one)..
I think you may have damaged the digitiser when applying the screen protector. Possibly the ribbon was only just making contact and your pressing on the screen has dislodged it enough to stop it working.
I've got a MDA which has a broken lcd. Its just cracked slightly, but still displays fine. I did a Clear Storage and now the phone has reset and is giving me the "tap here to set up your device" wizard. I need to bypass this and any screen alignment that may come up since the LCD touch feature no longer works. I've done it before when I got the phone, but I cant find the thread nor remember the steps.
Any help is appreciated.
you really can't. i heard theres a way you can flash a rom where the config has already been done, but i don't remember where i saw it
fzzyrn said:
you really can't. i heard theres a way you can flash a rom where the config has already been done, but i don't remember where i saw it
Click to expand...
Click to collapse
create a file on the root of your storage card called welcome.not
TylerC161 said:
I've got a MDA which has a broken lcd. Its just cracked slightly, but still displays fine. I did a Clear Storage and now the phone has reset and is giving me the "tap here to set up your device" wizard. I need to bypass this and any screen alignment that may come up since the LCD touch feature no longer works. I've done it before when I got the phone, but I cant find the thread nor remember the steps.
Any help is appreciated.
Click to expand...
Click to collapse
I believe this should help you.
http://www.freewarepocketpc.net/ppc-download-my-mobiler-v1-2.html
At least I hope it does.
Just create a file named WELCOME.NOT on your storage card and do a hard reset.
HI , I had this problem with all my old crashed PPC ,,, so delete this file and reboot ,,, /Windows/Startup/Welcome.exe
U can use the "Activesynce Explorer to browse the Windows Directory
Enjoy..........
use "Remote screen alignment" tool and bypass your start screen easily. search this tool in forum. you will get it easily..
Regards
welcome.not and http://www.freewarepocketpc.net/ppc-...iler-v1-2.html
THANK YOU SO MUCH kfletch and le_cactus. I'm not sure which of these worked since I did both but the welcome screen FINALLY went away. it took a while. i had to install the Mobiler software and I had problems getting my ActiveSync up but I created the welcome file by going to the desktop of my pc, right click, new , text document, i changed the default name "New Text Document.txt to Welcome.not" then I right clicked to copy it. Next---Once the Microsoft Activesync came up, I clicked on Explore --> My Windows Based Device ---> Storage Card then I selected paste to paste the welcome.not file. After this it gets a little tricky because your device has to sync again to filter the file back down to the phone. This took a while. Then after a few resets, the Mobiler software finally read 'connected', then it gives you a screen shot of your mobile device, i did a soft reset a few MORE times and it worked. It's not as cut and dry as previous posts made it sound. it's a pain in the butt.
My touch screen (T-Mobile Wing) stopped working after I used it in the bathroom while in the bathtub (I don't know what the heck I was thinking), well later that day the screen stopped working and the genius at tech support had me do a hard reset and software upgrade, which did NOT help. (whatever you do, don't call tech support, especially if the white dot beneath the battery is another color---you're screwed!!!)--AFTER tech support messes up your phone they won't bother to help you if they think it's due to water damage! I'm going to see if I can locate the forum regarding reloading the touch screen drivers. I think that may be the problem.
thanks dear I try i350 gSMART and working.
how do you select "YES" when mymobiler tries to install on the phone?
my screen is also broken, and i bypassed the welcome screen, but when i tried to install mymobiler, i cannot let the phone install remote.exe
any help?
this is ur answer
go to this its my room iam build it and not have align screen
http://forum.xda-developers.com/showthread.php?t=546422
Thanks a lot folks from XDA! I had screen broked and this works just fine! Cingular 8125 WM5. tks
ah_hin said:
how do you select "YES" when mymobiler tries to install on the phone?
my screen is also broken, and i bypassed the welcome screen, but when i tried to install mymobiler, i cannot let the phone install remote.exe
any help?
Click to expand...
Click to collapse
Buy a not broken screen
HTC TYTN(Hermes 200)
Hi there i have an HTC TYTN, happens that i'm suposed to have the same problem (maybe broken screen).
The phone was working fine untill today.
I can't bypass the screen alignment; i tryed both ways.
What can i be doing wrong?
Thanks in advance.
Bypassing with "logic"
Hi there;
In my case; i found a way to bypass it.
My screen has a 4mm scratch in the top left of the screen.
so i just pressed the bottom of the cursor (NOT IN THE MIDDLE WHERE IT'S SUPPOSED TO PRESS - "in the top left cursor" - where the scratch is)
after that i could use my phone again.
Also after this try finding the correct registry screen alignment and save it.
It will work properly.
welcome.not works for TyTN II with unresponsive touch screen . Blank micro SD card with just one blank file welcome.not. You can insert the sd card just before you hard reset
It worked in OMNIA II and passed the screen calibration..Thanks a lot guys!!!
Hi everybody!
I'm having problems with my Pocket PC.
It all begun a while ago, when a part of my screen stopped working (didn't respond to touches). So I did a hard reset. Then, it wouldn't pass the Align Screen procedure. So I made a file on the Pocket PC root folder called welcome.not - and it worked, the welcome screen was bypassed.
Now, however, everything on the screen is mirrored. Not the image on the screen but the response to my touches. So when I press the upper right corner with my stylus, it reacts in the lower left - and reverse, across the whole screen.
What I want now is of course a state like before the hard-reset. I can accept a part of the screen not working, but I want something at least to be useable.
I think this would be easily fixed by just running Align Screen, but that doesn't work - it gets stuck in a infinite loop.
Maybe there are some Align Screen "profiles" to place in the windows folder/registry?
I'm using a HP iPAQ 214 Enterprise.
Randor244
might it be a ROM problem?
Maybe, though I think the problem is that the screen is completely unaligned and therefore is totally wierd.
What I think I need is:
1. An application to browse the PPC registry from a desktop PC
2. Sceen align data to put in in the registry (I've read somewhere else that that data is stored in the registry)
Or, maybe I'm wrong
In case it is a rom problem, can I solve it easily in any way?
well to be honest, the first thing i'd do is switch a ROM... unless it's a ROM you got from XDA and is well-known..
if the rom switching doesn't work, i'd download a pda control app like MyMobiler or SOTI Pocket Controller to fix this. maybe you have hardware problems with your screen..
I don't know where the screen alignment data sits in the registry but i'm sure you can find it on this forum. if you manage to change and it still doesn't work... maybe replac ea screen? there's a marketplace section in which you might be able to buy spare parts.. and there are guide on dismantling so you can replace the screen yourself
well to be honest, the first thing i'd do is switch a ROM... unless it's a ROM you got from XDA and is well-known..
Click to expand...
Click to collapse
Well, I havn't got much knowledge on how to do these things... Could I get a brief explanation?
I know what ROM is and so on... but how to switch it... hmm...
I'm sorry, can't help you with that.. i'm not familiar with the iPaq... but I understand that you never switched a ROM so it's probably the original one.. and you shouldn't have a problem with it.
try aligning your screen using the registry.. if it doesn't work.. i'd go with replacing a screen.
Yeah, I would also like to align the screen using the registry - but how? I need to know some values to input, right? And as far as I know they need to be specific for my model
So how?
maybe you can contact HP and ask them?