Hi,
I've just received my TyTN today and I'm not very satisfied concerning the touch screen.
I don't know what is happening but the touch screen does NOT respond properly. I've tried to clean it a bit, but the result remains the same.
When I want to use the screen keyboard, it's horrible. I point the letter A and the screen understands that I'm touching the letter under or the letter just near the "A". It's pretty impossible to write a text properly and very hard to open programs or browse with the touch screen.
Of course I've tried to align the screen. It's working without any problem then.
But after some times, opening apps, closing others (using normally the pda inf act), the problem comes back... the TyTN does't really understand where I'm touching the screen.
Then I make a screen alignement, and it's working back... It's just amazing
I don't think it's a hardware problem because the alignement is working after an align screen.
Maybe it's a known error ? Has somebody the same problem ??
Is there a rom update to fix that ? Or is it a problem of my own HTC ?
Thanks !
Can you help me please ?.
Hi,
I don't have this issue with mine...
Check the "TnTN/v1604 problem" topic maybe
I had the same thing, once, with my variO. Probably I pushed too hard onto the screen while cleaning.
Actually, this is a known problem with some of the first shipment devices. Look at the other TyTn topics i this forum.
Related
hello
i got my polaris for 3 days: everythig ok until i applied the screen protector (i think there started my problems):
first simptom - touch screen with response problems, than not working at all! (yes i removed the screen protector)..i hoped that maybe it is a software problem.
i have tried using it with the buttons - manged to lock the keypad
so after searching the net i found the way to "hard reset"...but that needed both gps and IE buttons pressed.... locked
Next step: i found this forum ..searched for any similar problems..no luck
Tried to flash the ROM using both bepe and udK (bittdefender found "Trojan.Qhosts.AQP" in udK release ) tools. Both tools stucked at 0%.
Another tool needed EnterBootloader.exe to run on my PPC. but without keys/pen i could not install it, so i put the a command for program in my Startup tasks on the PPC.
Now the ppc starts and then goes in the 4 colour mode. I'd tried to install/flash the ROM again..no luck stucked at 0%.
Can anyone help me?? could it be a software problem? or maybe it.s a hardware problem. (i gor no response from the touch screen since)
Thanks!
P.S. Sorry for my english..hope u understand my problems
One question: did you use water or something else to place the screen protector on your device?
Return it asap!!
I used some glass cleaner (foam)..but the screen was dry and clear when i put the protection.
The phone is in service now...(repair..if not a new one)..
I think you may have damaged the digitiser when applying the screen protector. Possibly the ribbon was only just making contact and your pressing on the screen has dislodged it enough to stop it working.
Hi!
The screen of my Prophet works correctly.
After I've installed a contributed rom, my device boots correctly (after hard reset) and then ask me to align screen but just after I tap to enter in align procedure, it didn't give response anymore! So it enter (tapping the screen) in the align procedure, but then no repond any nore!
I tried to install other roms but... nothing to do: the is always exactly the same:-((
What can I do? Go back to WM5?
What's the correct procedure? I didn't found it...
I've tried to and...
Now I've installed NVID rom
but when appears "tap here to set up your Windows Mobile-based device" I tap on the screen (so touchscreen works) then pass to "align screen"
here if I touch normally it didn't work but if I press and move a little the pen on the cross (like designing very little circle) it works.
After alignment procedure, Prophet seems to works regularly, I mean I just nee to simply touch screen and it works.
Do you think it's the beginning of an hardware problem?
this happened to me as well. i can't touch the centre cross hair, but can with my finger, the other cross hair i can tap with the stylus. also on the keyboard, i can't tap esp the no. 8 & few letters below it esp G.
still happens to me even with another rom. don't know how to correct it. i guess a new screen is the key... or get a new pda - i'm waiting for my touch pro!!
all roms problem
Yep, it seem like it don't receive a spot area touch, but only wide area touch.
But this appens to me for «all» roms I tested and «only» for alignment procedure!
After I get screen aligned, it works perfectly, and seems to have normal sensitivity.
The problem is only for align procedure!
But it sounds strange that you can't use "8" or "g": it seems really a problem with touchscreen or maybe it is to clean a little.
But you are a lucky man! Touch pro is coming in your hands...
Bye
today i flashed a new rom
as u all know the "align screen" setup is the first that starts within the initial setup
but it wont complete, it just starts over and over again
i remember that i had the same problem during the last rom i used but i just killed the process and forgot about it, but now i cant kill it bcs its newly flashed
did any of u had the same problem before?
ok solved , after getting a bit angry and googling for 30 min i hammered a bit harder with my finger
dont ask me why but this helped at the first try
maybe some of u could explain why that is and/or how to get it better solved
This is supposed to be a CALIBRATION screen. It expects you to be as precise as possible. Using your finger instead of a stylus is usually not precise enough, and being detected as such, hence the calibration restart. All you really had to do is use the stylus, not your finger. Pressing harder with your finger makes it easier on this type of the screen to detect it's location, hence results in a little bit better precision. Thats the reason it allowed you to pass that screen after all.
sry for the late answer
im using the stylus ofc, but this aint help any much
only when i use my finger and press a bit harder im able to "calibrate"
installed some roms since my first post and the problem stays
Hello friends, I am Brazil, sorry for my english ...
I'm having the same problem to calibrate the screen on my HTC TOUCH CRUISE (P_3650), researched several posts, but could not solve the problem, I installed other ROMS, but also not resolved the problem, returned to ROM 6.0 ORIGINAL factory, but after a while the screen loses calibration is not working anymore ...
I ask to help me solve this problem ...
Thanks
I have the well-known problem with the screen of my HTC. Ever since I changed it after it got broken there is a line slightly over the centre of the screen that does not work. I tried to change the ROM, the RUU, download and load it without touching the screen and many other ways to it... And it continues not working at all. When I connect my phone to the HTC to the computer, when I touch the screen it works randomly, it maximizes and minimizes just by pressing once... When I try the switching on-switching off stuff it gets solved, but the stuff of the line mentioned before. I would be grateful if you could provide me any satisfactory solution.
Thank you beforehand.
I have the well-known problem with the screen of my HTC. Ever since I changed it after it got broken there is a line slightly over the centre of the screen that does not work. I tried to change the ROM, the RUU, download and load it without touching the screen and many other ways to it... And it continues not working at all. When I connect my phone to the HTC to the computer, when I touch the screen it works randomly, it maximizes and minimizes just by pressing once... When I try the switching on-switching off stuff it gets solved, but the stuff of the line mentioned before. I would be grateful if you could provide me any satisfactory solution.
Thank you beforehand.