Ok, I have a BT200 that is working very quirkly with my i-mate. Sometimes the phone transfers the call to the headset, sometimes it doesn't. After deleting and recreating the bond, it works, but not for long. Anyone have one of these setup and working properly? Is there a trick to it?
Also, does anyone know if other headset drivers exist that may work on the i-mate that would allow you to hear all audio (not just phone) through a bluetooth earpiece?
Figured it out?
Ok, I've finally pinpointed that it works fine until I turn off the jabra headset, then when I turn it back on, I have to go through the entire thing again of re-creating the bond, etc..
Anyone know how to avoid having to recreate this everytime I turn the headset on or off?
I don't now ... but i have also jaba 200 and the MDA II is must arrive...
well please chip us informed
Thanks
DenisJ
I have the same combination and have also observed the same hassles.
It seems to work when I turn the BT headset function on the MDA off and on also. Thsi seems to result in a rebond.
Exact Steps
TBD,
If you could post the exact order of the steps you take to turn on / off the headset, I'd appreciate it. Right now, I'm doing the following:
1. Finish BT Headset Call.
2. Disable Bluetooth Headset Mode on Phone.
3. Disable Bluetooth on the phone.
4. Hold button on JABRA to turn it off.
Then, attempting to...
1. Hold button on JABRA to turn it on.
2. Enable Bluetooth on the phone (Set to "On" or "Discoverable")
3. Enable Bluetooth Headset Mode on phone.
4. Attempt to make call.
So if you could posts steps like that, i'd appreciate it. Also, do you set your bluetooth to "On" or "Discoverable"? Do you ever turn off the Bluetooth Radio completely?
Thanks,
Jon.
Yup me an all. I too have the Jabra BT200 and have the same problem. Providing you don't switch off the headset or go out of range your ok, but for instance when you leave the headset in the car and take the XDA2 with you you have to create a new bond to use it again. AHHHHHHHHH!!!
Shame cos so much else has been sorted on it.....and more. What a piece of kit!!
SOMEBODY HELP!!!
OK, so here is the sequence, which seems to work (for me).
1) I set everything up as per instruction. creating the bond between the Jabra and the MDA II.
2) Before (or after) I turn off the Jabra I disable the BT-Headset on the Today-screen.
3) Then I turn the Jabra on again and wait several seconds before enabling the BT Headset on the MDA II.
This seems to work most of the time, though the hint regarding going out of distance might explain the instabilities I have still observed. In any case, using the BT-Headset ON/Off on the Today-screen seems to resync things most of the time and get the Jabra up and running again.
Hope this helps and always open for new ideas
I have been a bit impatient after turning the BT headset on. I'll try it and let you guys know.
I may have been a bit optomistic. :roll:
Today I observed that sometimes the Headset reacts very late. Consequently you miss half of the call. Seems to be an XDA problem.
As for my XDA II with Sony Ericsson HBH-65, after creating the bond, before i turn off the BT headset, i turn off BT profile and BT on my PDA, then turn off the Headset.
If i want to turn on the headset, i activate BT on my PDA, then BT profile, the the headset. Sometimes in teh day headset seem to lose the bond and cannot use the BT to call or whatever. I tried turning on/off BT on my PDA, did not work. Turn on/off headset, it worked. So for me most of the time is my headset causing the problems
i am having the same problem with the new moto bluetooth headset although i have experienced no problemzs with the se hbh-30 bluetooth headset....i can turn off and transfer calls without any impact on teh bonding
Jabra problems
I've had similar problems on a boring old Nokia 6310 with my BT200. In the end, all I could do was find the 'automaticly reconnect' option on the Nokia. during calls, the link is allways fine, but between calls, when I guess one end or the other goes to sleep, the link will drop out, and then instantly reconnect. This happens around 2 or 3 times an hour.
Is there a 'automaticly reconnect' option on your XDA?
All the best
James
OK, I finally sacked my Jabra 200, because of its instability. What use is a headset, that doesn't repond when a call comes in? :evil:
I bought a B-Speech from B-Data yesterday and it seems to be working much better :lol: .
Nokia HS-3w headset with XDA II
Well! I am using the Nokia HS-3W Bluetooth Headset with my XDA II . I can pair up two devices and use it for only ten minutes :twisted: . After that, the headset will off(goes to sleep) . I Have to turn on the headset every ten minutes. I ask the dealer about the problem. They told me this headset work fine with Nokia's phone. They told me , there is three color on the light. Red light will flash when you turn off the headset. Green Light will flash when you turn on the headset up to ten minutes, if cann't find the phone devices , it will goes off.White light will flash, when the headset connected to the phone. When I turn on the headset, I just can see the green light only.But, if someone call me or I make a call ,the white light will flash.After the that the headset will flash the green light again for about ten minutes and goes off. Can anyone help me with this problem? Thanks!
@[email protected]
Hi, I will like to ask how your headset B-Speech is working.
It works 100%?
I have a jabra 250 with the same problems as BT200
Please let me know
Regards
JoseF
The B-Speech Headset is working OK, however it doesn't solve the problems with the Microsoft BT-stack.
Some observations, probably also applicable to the Jabra:
:?: When you go out of range with the headset, it will probably not reconnect automatically (but how do you know)
:x On an incoming call, the XDA may be very slow in activating the headset, so you might miss the call (seems to be tied into what the XDA s/w is just doing at the time
When you turn the Headset off, make sure to turn it off on the Today screen first. And when you turn them on, make sure to wait about 2 sec. after you turn the headset on before turning it on on the Today screen.
:idea: What seems to work best, is turning that Headset off and then on again on the Today screen. It usually comes back after that.
Mind you, it isn't the headset thats causing these problems. Its just that Microsoft botched the Bluetooth stack - probably the programmers had blue teeth from all the wine they were drinking!
I've found the out of range issue to be mute on my jabra 200. The only time the bond is broken is when the headset has been turned off. Or sometimes when it has been on charge.....
Strange........I use the Jabra BT 250 with the MDA II and have non of these reconnection problems. I f I turn it on and place a call (or receive) it reacts immediately.
However, I cannot use the advanced Headset Profile features of the Jabra with the MDA, but this is not the fault of the Jabra........
Could the people who are having problems and the people who are not having problems with their Jabra BT200's please post their version numbers of the Jabra BT200. You can find the version number on the boom going to the microphone. It will be 2 numbers and a letter, like 48A or something like that. I'm testing a theory that I think will help identify why some people work and some don't.
Thanks,
LouisK
Ok, the number on my Jabra Bt 250 is 44B.
Hi, can someone help ? I've tried a bluetooth headset Jabra 250 and also a Sony HBH-35 with a I-mate.
I can get them to bond and also identify as default headset but I can't transfer a incoming or outgoing call to the headset.
I've also done several soft resets and no improvement.
Any ideas ? do I need a new upgrade or something.
Other than this small problem, I'm very happy. I have also success with the Sandisk wifi SD card.
Thanks for any tips, Dave
how are you bonding the headsets?
on my hbh-60 I have to hold the button in for a few seconds
on first powerup to get it into discoverable mode(red/green LED flash)
Then search for it with the XDA/MDA/iMate
I have had no issues with bonding.
What version iMate are you running?
G
Hi,
I'm not sure what information about versions is needed to help resolve this problem but:
ROM version 1.03.00 USA
ROM date 09/24/03
Radio version 1.05.12
Protocol version 1337.12
ExtROM version 1.03.20
When these are not up-to-date where do I get the current ones from ?
Thanks, Dave
Have you turn on the bluetooth headset mode (one item on the default today screen, not the bottom right icon)
I have been using the Jabra bt200 for a while now. The problem is, everytime you turn bt200 off, you have to rebond again. It also works a bit differently. Once bonded, it automatically transfers to headset on dialout. For received calls, you still have to use the headset button. I am looking for another headset that won't require constant rebonding.
Hi, thanks again for the tips.
NOW the HBH headset works. I put the "profile" option back in the Today display and then checked everything again.
Then I tapped on the headset profile on the today screen - this turned it off. Then, I tapped again to turn it on.
Now the headset works fine !
I'll try again later with the Jabra.
Thanks - Dave
Thanks Much !!!
Just wanted to thank this forum and this thread. I just got a HBH-65 yesterday and could get it to bond ok, but it still wouldn't work. It turned out to be not having the "Profile" shown on my Today screen. I placed it back on the Today screen and enabled it and it works great now.
THANKS MUCH GUYS !!!
Hi all!
Here is my problem (tried with several other headsets as well):
When the headset is connected to the phone and you take it from larger distance than it's disconnects of course. BUT when you take it back it doesn't want to reconnect automatically. It's really annoying thing, because i'm using a stereo headset to listen music, and i can't bring it with me everytime when i have to move from my desk. I've had some other HTC before but never experienced this untill now on Raphael.
Any idea how to force TP to try to reconnect as the other devices do?
eami said:
Hi all!
Here is my problem (tried with several other headsets as well):
When the headset is connected to the phone and you take it from larger distance than it's disconnects of course. BUT when you take it back it doesn't want to reconnect automatically. It's really annoying thing, because i'm using a stereo headset to listen music, and i can't bring it with me everytime when i have to move from my desk. I've had some other HTC before but never experienced this untill now on Raphael.
Any idea how to force TP to try to reconnect as the other devices do?
Click to expand...
Click to collapse
is this a new BT headset you're using now? I believe some bt headsets simply don't (re)establish connection by themselves
There is a new Bluetooth stack in the Raphael compared to older HTC devices, so this could be an issue with it. Have you tried pressing your headset's play/pause button when you come back in range?
Trancecoder said:
There is a new Bluetooth stack in the Raphael compared to older HTC devices, so this could be an issue with it. Have you tried pressing your headset's play/pause button when you come back in range?
Click to expand...
Click to collapse
Motorola H3 headset: if i press the call button that the connection is reestablish
IQUA BHS-701-S: i have to turn it off than on to make the headset recconnect
btw: i've also noticed, if no device connected on BT, than raphael simple turns off the BT after a while
Mine has never turned BT off on its own. There must be an option for it, perhaps in power saving.
Hi I tried 2 different bt headsets
for my diamond but it can't see the devices!
I've got the nokia bh101 e a samsung wep301.
i tried the nokia and no way then i found this wep301 from a friend of mine and it has a reset button. i tried to reset but no matches with diamond...
the wierd thing is that i tried with my mac also and it can't see them too!!
Any idea about how to become visible devices?? I've got the bs14 radio
thanx in advance
solved by myself:
I have to put the bt headset in pairing mode just pressing the multifunctional button from off for about 10 secs to led static light and not blinked then search with your phone or mac or pc, after that you can pair it succesfully
Hi guys,
I've got a lot of problem with my Xperia X1.
First I had camera problems, than vibration, they house cracking, mini mouse stuck and now my headset plugin.
I was outside and listened to music. When I came to home battery was empty so I charged it. When I turned on and headset wasn't plugged in I got it still in Headset Mode which makes me stuck right now.
I've tried to update rom, but didn't helped.
I've tried to plug in and out toooo many times, but still not worked.
I've turned my mobile off and plugged my headset out and turned mobile on, but still not fixed. And I saw I'm not the only one which has this problem.
Any other fixes are always welcome.
Thanks anyways.