Hello all. I have followed the instructions to get wm6 and got stuck on step 9 of Karhoe's guide. Activesync will no longer see my device. so i cannot move forward. my phone is stuck on bootloader screen. After 'resetting device' in terapro. i saw the splash screen on my device then it went immediately to the bootloader color bars. everything else showed exactly what was on Karhoe pics. i just need activesync to see my device so i can proceed. any suggestions please. Thank you very much.
Activesyn will not see your device as it has been wiped clean of windows. Since you will need to be in booloader screen to install wm6, it doesn't matter if your activesyn sees your phone or not.
I ran into the same issue, i had to actually disable the 'allow usb...' option in activesyn so the romupdater utility can see the phone. So try it both ways.
enable it as suggested and just run the next step of installing the wm6gsmupdate...if you get some message saying connection error, then disable it and try again.
no activesync. Error [264]: Connection
thanks for the reply flashhsalf. it has not worked out for me tho. i tried both ways several times. enable/disable usb. i get same ERROR [264]: Connection.
im going to try it with a different laptop.thanks again.
Once I have this error too. Just reboot my PC and format BINFS one more time and all became fine. Don't know that is the reason, but this trick was helpfull
Have You re-enabled "Allow USB connection" @ connection options in Your Activesync??
got it to work...!!!
thanks all. i tried what was suggested all day...then when i went home i tried again with no success. to the point where my battery just died. i thought it was a paper weight at that point. but i decided to plug into the charger and the bootloader came up again. this time without the USB indication in the lower left corner. after a 2hr charge i took it to the same laptop which i rebooted. enabled usb then it worked! strange but glad i got it to work. Thanks again folks!
i updated to 6.1 but im experiencing issues with internet. ERROR
the remote party has ended this connection. this is the case with MMS as well. anyone experience this?
xdabe said:
Hello all. I have followed the instructions to get wm6 and got stuck on step 9 of Karhoe's guide. Activesync will no longer see my device. so i cannot move forward. my phone is stuck on bootloader screen. After 'resetting device' in terapro. i saw the splash screen on my device then it went immediately to the bootloader color bars. everything else showed exactly what was on Karhoe pics. i just need activesync to see my device so i can proceed. any suggestions please. Thank you very much.
Click to expand...
Click to collapse
i am also stuck to the same point ..
please help me what to do , why does this happens ..
i am very nervous ...as i cant make it a paperweight...
please help ..
thanks
my device is IMATE SP5M
and i have correctly done steps upto 8...
and when i try to do step 9 i only get three color boot loader screen
my device is super CID
info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x7820000 Bytes
HTCSSuperCID ' HTCE
Xdabe if you actualise Radio ROM, before upgrading to WM6.1 you wouldn't notice that problem with an Internet.
Try upgrading Radio ROM for your device.
Gsmsikar once you are in bootloader, and have SuperCID, just start installing Radio ROM first, then OS.
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
I have similar problem, can't connect to PC anymore, but flashing with SD card works for me
have you tried different ROM images?
TQY said:
Hi Help me pls,
I've tried to flash my rom via ActiveSync. Every thing went well until i get the progress bar then it got stuck at 0% for ages so i disconnect the whole thing and tried to restart the process.
NOW I CAN'T ACTIVESYNC ANYMORE !!!! but the connection as "memory card reader" still working.
I went through all the post and tried to flash the ROM via bootloader with the "RAPHIMG.nbh" in my SD card ( already formated FAT32 ) but every time the PDA got stuck at the first stage "loading".
HELP ME PLEASE
Click to expand...
Click to collapse
It sounds like you did not carefully read this.
That is also where this should have been posted. A new thread should not be started for this type of issue. I understand you are panicing. However, in almost all situations the phone can be recovered.
That said, Hold volume down and hit the reset button. It will put you in the tricolor screen. In the white it says serial. Connect it to your usb cord. It should now say usb. Now flash the STOCK rom.
be sure that battery over 50% then follow arupphental's
I have a friend with a kaiser and the same problem. can this be applied to it? i dont want to search through the forum forever...
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
X2D said:
I would start by going to the kaiser forums and checking the stickies. Search within the kaiser forum also works.
Click to expand...
Click to collapse
ok i thought someone would say that. was just wondering off hand. thanks x2d
A.creature said:
I have This problem on Vista OS, i connect my touch pro after reboot system, and if i disconnect device and try again connect, my system not see device!
On device manager in OS, my touch pro stay present after disconnect device. This problem retry if after connect i try flash rom on device, black screen on and flashing stop with error connect to device.
Please Help!!!!!
P.S. Sorry my Bad English
Click to expand...
Click to collapse
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
I had the same problem after a faulty ROM from Vodafone NL, what I had to do is before I wanted to flash my ROM do a hard reset on my device (please back-up your personal data before doing this). After the hard reset, I could get a stable connection with activesync and flash my ROM
While the circumstances are different, my advice is still the same: http://forum.xda-developers.com/showthread.php?t=481527
longnguyen30 said:
go to bootloader (tricolor on screen)& flash a rom, your PPC 'll be fine. when you flash ROM, PC transfer data through USB to PPC therefor not need connect by activesync.
Click to expand...
Click to collapse
Stumbled upon this.. and yes the advise is good, when you run the flashing utility (i.e. CustomRUU.exe), it says you need an Active Sync connection, but you really dont, you can flash it anyway, it seems to find the device via USB regardless.
ufff!!!! to me yes found right, thank you thank you to first post. (flashing from SD)
Undetected
Well i had the problem where my phone wasnt getting detected at all.... i put the stock rom and radio but couldnt put stock spl on the phone with sdcard.... after trying different computers/usb wires/settings i returned it for a new one and this one works fine.
Hey, I searched and searched for solutions to this problem although nothing seems to help..
I keep getting a message saying "USB Device not recognised" whenever i econnect my touch hd via USB.
Iv tried the following already but still no use
- Hard reset
- Flash new rom
- Updating drivers
- trying on another computer
- trying a new usb
- turning off faster usb connection in Settings>Connection>USB to PV
none of the above fixed the problem
someone had written that flashing via mtty could cure the problem although i cant connect my device to the computer so its impossible to even flash my phone!
Any one have any fursther suggestions?
Anyhelp would be greatly appreciated thankyou
Bump
Anyone still?
Hi all, I have been experiencing problems with my WMDC. After flashing a new ROM i get an error that says "connection error please disconnect and reconnect your device" but i do ant it doesnt fix the problem. I use Energy ROMS all the time and i usually sync right before I flash. The only way i have found to fix the problem is to format my computer and that is a pain in the yo know what! I have tried repairing, re-installing WMDC with no luck. I try re-flashing my phhone and still no luck. I tried my gf's phone which is the same as mine and no luck. My phone by the way is the htc pure from att. Any help would be great. I am running WMDC on Vista 64. Thanks
I need help guys. I tried to flash the bootloader and something went wrong. Now it starts up with the three color and have this displayed.
RUUNBH
PANT200
SPL-0.36.0000
CPLD-2
Upgrade ROM code error
Please try again
Serial
It can still detect the USB connection, however it will always timeout. Can anyone help me out with this? I am new to this; So if you can be as detailed as possible it will be great. Thanks in advance.
Update:
So far i've tried loading rom from sdhc card formatted FAT32. With Matbee's version and also Cfays wm6.1. Both however are stuck at Loading after bootloader.
I've tried connecting it to windows but since it won't sync, I can't do anything there. At this point, anything I can do or try is worthwhile.
Thanks.
pekklejai said:
I need help guys. I tried to flash the bootloader and something went wrong. Now it starts up with the three color and have this displayed.
RUUNBH
PANT200
SPL-0.36.0000
CPLD-2
Upgrade ROM code error
Please try again
Serial
It can still detect the USB connection, however it will always timeout. Can anyone help me out with this? I am new to this; So if you can be as detailed as possible it will be great. Thanks in advance.
Update:
So far i've tried loading rom from sdhc card formatted FAT32. With Matbee's version and also Cfays wm6.1. Both however are stuck at Loading after bootloader.
I've tried connecting it to windows but since it won't sync, I can't do anything there. At this point, anything I can do or try is worthwhile.
Thanks.
Click to expand...
Click to collapse
sorry for the late reply but it looks like you need HardSPL here is the tutorial to HardSPL your Phone for CDMA http://forum.ppcgeeks.com/cdma-treo-pro-development/84822-treo-pro-cdma-hardspl.html