Database Info

Does ROM flashing need ActiveSync?

I am having lots of problems getting ActiveSync to work. I can transfer files using Bluetooth.
Do I need a working ActiveSync connection to flash a ROM?
The Hard SPL pages talks about connecting the ActiveSync cable, but does not say why this is necessary.
I have a 4 Gig MicroSD card installed. Can I simply load all the necessary files onto it and go from there?
Perhaps a non-Orange ROM will solve my ActiveSync problem (not the reason I want to flash, but a possible good side effect).

Yes, you need activesync or the vista counterpart.
Try this - go to Settings | Connections | USB to PC | UN-check Enable Advanced network functionality and see if that helps

derek-farn said:
The Hard SPL pages talks about connecting the ActiveSync cable, but does not say why this is necessary.
Click to expand...
Click to collapse
ActiveSync will tell your Windows XP that the connected device is a Pocket PC and not something else. (Drivers)
I have a 4 Gig MicroSD card installed. Can I simply load all the necessary files onto it and go from there?
Click to expand...
Click to collapse
ROMs can be flashed with SD card. But the method and the files are different. Usually this is not on a first priority choice for cookers. And I dont remember Hard-SPL through SD. Though, going through a PC is always best as flashing ROMs are quite dangerous and if anything gets stuck in the middle, you shall try again from the PC but not through SD when your device doesn't even boot!
Perhaps a non-Orange ROM will solve my ActiveSync problem (not the reason I want to flash, but a possible good side effect).
Click to expand...
Click to collapse
Original(shipped) ROMs are always best. They dont give you much errors. People recover their device using original ROMs in case if they bricked their device using a cooked ROM! Original ROM can be flashed direct from Bootloader screen most of the times but would still require ActiveSync be installed.
Regards,
Carty..

You can use your memory card as per instructed here > http://forum.xda-developers.com/showthread.php?t=336158
Also you could try and put your phone into the bootloader mode by hand (instructions here > http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets ) that should work also as your computer uses a different set of drivers when flashing

ActiveSync sync problems using USB

Hey all. Sorry if this is in the wrong forumsection, feel free to move it if so.
I am having problems syncronizing my TyTn II with my PC. I am using Activesync 4,5. I read somewhere that this can occur if you change the usb port from the one you were using the first time, and i think that is what i might have done.
Has anyone else had this problem? What can i do to fix it?

This (registry change) did the trick for me
http://www.aximsite.com/boards/activesync/120851-activesync-4-1-sygate-personal-firewall-pro.html

Thanks mate, that seems to be a solution to the problem. Only problem now is that as far as i know i dont have a regedit program on my phone. Which one should i use and how to i go about using it? How do i get the program onto my phone when i cant use Activesync?
Appreciate any help..

I just started a thread like this in the Hermes forum
http://forum.xda-developers.com/showthread.php?t=361633
here's what i got, haven't tried it yet.
cyberscribe said:
Try this procedure step-by-step
1. make sure your phone is not connected to the computer in any way
a. Bluetooth off
b. WIFI off
c. USB cable not connected
2. Run spybot S&D (I always do this when the computer misbehaves - and make no mistake your computer is misbehaving)
3. Terminate all other running programs
4. Hook your phone to the usb cable and the usb cable to the computer. (don't worry if it syncs or not)
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
7. Disconnect the Phone
8. Open the Control Panel "Add/Remove Programs" and uninstall Active Sync
9. Reboot the computer
10. Connect to the internet and get a fresh copy of Activesync 4.5 and install it.
At this point if you can back up your PIM to the storage card or something it would be great because I suggest you do a hard reset of the phone. go to the settings page and select System. Tap the clear storage icon and follows the instructions to reet the phone.
11. Reset phone as above
12. When phone reboots, connect it to the computer via the usb cable.
Phone should sync from now on.
Good Luck
PS.
MrVanx is right, that could help but it will limit your phones capability. However if my method fails that may be your only option short of reflashing the phone with some other ROM.
Click to expand...
Click to collapse

Thanks for the tip there, sook. I just tried it and it didnt work for me.
I did all the steps except for these:
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
The thing is i cant find my mobile device anywhere in the device manager or in the network adapters subcategory. Any ideas?
Is there any way to edit the registry on my phone without having to download and install something? Like a built-in program or something..

SeqHTCTyTnII said:
Thanks mate, that seems to be a solution to the problem. Only problem now is that as far as i know i dont have a regedit program on my phone. Which one should i use and how to i go about using it? How do i get the program onto my phone when i cant use Activesync?
Appreciate any help..
Click to expand...
Click to collapse
Download through wlan or copy it to the memory card with pc...I used TascalSoft TRE:
http://www2r.biglobe.ne.jp/~tascal/download/pocketpc/tre_e.htm

USB unknown device

I've tried the drivers from Samsung, Keis, ODIN one click. None of them worked on 4 different machines, Windows 7 both x64 and x86(which was a fresh install), and two Windows XP machines. I tried it on Ubuntu(10.04 LTS) and that recognized the captivate.
Anyone know how to get one of those to correctly recognize my Captivate so I don't stuck on Samsung's/AT&T's 2.2

uninstall all of the driver that you downloaded. uninstall kies. then go to samsung.com search for the captivate, choose you phone, click the 'i own this' button. then go to get downloads, software. click on the .zip file icon next to usb drivers. if that didnt work uninstall them then download kies again. if it still doesn't install them, open kies, click menu, reinstall drivers

What is it that you're trying to do?
Sent from my SAMSUNG-SGH-I897 using XDA App

If it is coming up unknown device try another port. You may want to try another microusb cable as well.
Sent from my SAMSUNG-SGH-I897 using XDA Premium App

I've always had luck with the drivers in the captivate aio toolbox. Even on a fresh win7 64bit when I replaced my boot drive with a ssd a month ago.

Samsung really failed at the USB drivers for the Captivate. I would expect to be able to install the drivers from their website. Plug in my phone, and have it working.
trell959 said:
uninstall all of the driver that you downloaded. uninstall kies. then go to samsung.com search for the captivate, choose you phone, click the 'i own this' button. then go to get downloads, software. click on the .zip file icon next to usb drivers. if that didnt work uninstall them then download kies again. if it still doesn't install them, open kies, click menu, reinstall drivers
Click to expand...
Click to collapse
I tried that before, didn't work.
bornjamerican said:
What is it that you're trying to do?
Click to expand...
Click to collapse
I'm trying to:
1) connect as a mass storage devices. Yes I know turn on USB debugging and to mount the drive.
2) flash back to stock 2.1 or root my phone so I can install a custom ROM on it. Might go with CM7/MiUi or something from Team Phoenix. So use Odin3
shinji257 said:
If it is coming up unknown device try another port. You may want to try another microusb cable as well.
Click to expand...
Click to collapse
Tried all of the ports on the computers. I don't have another microusb cable to test to see if that's the problem, but I'll check that tomorrow.
Johnnie5000 said:
I've always had luck with the drivers in the captivate aio toolbox. Even on a fresh win7 64bit when I replaced my boot drive with a ssd a month ago.
Click to expand...
Click to collapse
I'm going to try a fresh install of windows 7 32-bit with aio toolbox see if that works.
Tried my friends brand new microUSB cable. It worked.

I have tried 4 known good cables know, 4 different computers and every USB port available on all 4 of the PCs I tried. Only once did it identify the device and install the drivers and I was able to root it but I still can't sideload because after the reboot after rooting it is back to device not recognized/unknown device. This has been a total pain. Any suggestions? I'm not with AT&T any more so I am out of luck for just bringing it into a store and asking them to take care of it.
Edit: Sorry for bumping an older post but I did it instead of starting a new thread.

rmriggin said:
I have tried 4 known good cables know, 4 different computers and every USB port available on all 4 of the PCs I tried. Only once did it identify the device and install the drivers and I was able to root it but I still can't sideload because after the reboot after rooting it is back to device not recognized/unknown device. This has been a total pain. Any suggestions? I'm not with AT&T any more so I am out of luck for just bringing it into a store and asking them to take care of it.
Edit: Sorry for bumping an older post but I did it instead of starting a new thread.
Click to expand...
Click to collapse
If you're just trying to transfer apk files to it for sideloading, you can use a wifi transfer app. I use Wifi File Explorer and it's great. You can connect to your phone via web browser and upload/download anything on the SD card.
Another option is to use an external SD card that you can remove and plug into your computer, transfer the files to it, then insert it back into the phone.
This won't work for connecting to PC apps like Odin, Heimdall, or Kies, but for simple file transfers it works like a charm.
Additionally, regarding other usb cables, you didn't mention what types of cables you used, so I'll throw in another thought. The cables that come with the Captivate don't work on some PCs (like my new iMac). Third-party, generic usb cables might not work, either (I tried some and got a whole lot of fail). The only cable that works for me is the one that came with my wife's Motorola phone. If you haven't tried one yet, I would recommend getting your hands on a Motorola cable and testing it out. You'll immediately notice the cable is much thicker. I don't know if that has anything to do with why it works when others don't, but there's something about that cable that others don't have.

Bad Phone?
Could it be the phone port is having issues?
I've had the same problem and it seems that the port on the Captivate is shot which may be your issue. it will always charge; but tends to cause a lot of profanity when trying to get a PC connection to transfer files or flash it. It will be seen, then immediately play the 'unplugged' sound from windows. I've sat there and had it play the tones of plugged in and un plugged over and over again just by tilting the phone from side to side. No matter what cables I use (tried several but they are all samsung due to the recessed port). If it establishes the connection; I have to be very still with it or it'll lose it. If it loses it; I get unknown device messages or not functioning messages on that port until I reboot the PC.
Trying to flash anything via ODIN takes a lot of patience.
Those same cables / USB ports are used on my wife's Focus without ever having a problem. I wrote it off as too much flashing / overclocking of my phone but am not sure.

hi i was having this issue as well. i solved it by:
1. download a good & stable miui rom, rename it to update.zip and place it into your sd card. i took the sd card out of the phone and used a adapter to connect the sd card to my PC since i can't access my sd card through the usb port.
2. put the sd card back into my phone, turn off my phone. press and hold volume up and down buttons, then press n hold the power button till the screen shows something.
3. select install from sd. wait until the installation finishes and select reboot the phone.
4. when you're in your new miui rom, try to connect your phone to the pc via usb port again.
this worked like charm for me.
about the miui rom, i suggest you to use the one from miuiandroid.com (the UK version)
after flashing the rom im able to connect via usb and use mass storage.
hope this helps

Also, when you uninstall drivers, don't forget to look in the program files for anything that may have been left behind and delete it.

From the description it sounds strongly like you are actually experiencing a port failure which is common on the Galaxy S devices. PM me if you need this repaired...

Only try another usb cable, i bricked my cappy with a bad contact cable on odin, unknown device too, new cable=i897 device on windows notifications
try and feedback!

strange, this only happened to my when i soft bricked my phone. try connecting it to your computer in download mode

I had this issue once before. Here is what I did which resolved the problem. I was using a windows 7 PC
1. Download the ADB kit and extract it to C drive.
2. Connect your mobile to the PC on USB port
3. Wait for the drivers to be installed automatically (it might give you a failed to install message)
4. Never mind that message. Open Device Manager
5. In Device Manager, if you expand the "Universal Serial Bus Controllers", you'll see a device that has yellow question mark against it. This is your phone and since drivers are not installed properly, it has the question mark.
6. Right click that device, and select "Update Driver".
7. IN the window that comes up, select "I'll select a driver".
8. Browse to the folder where you have extracted the ADB kit on C drive
9. Check include subfolders and click Next.
10. The drivers should be be installed and your device should be identified by the computer.
Let me know if it works for you.

[Q] Why can I no longer mount usb

I have erased the contents of the phones internal USB storage. Now I notice that I cant mount to my PC.
Anybody know what happening or had same problem

Have you already tried formatting with CWM?
Perhaps this thread contains some useful information for you.

maksymillian said:
I have erased the contents of the phones internal USB storage. Now I notice that I cant mount to my PC.
Anybody know what happening or had same problem
Click to expand...
Click to collapse
I know this is a long shot but go to your dialer and input *#*#8778#*#* and make sure it looks like this pic. I fool with QPST and other things and sometimes forget to change the settings back to PDA and it will not mount. Long shot but what the hey...

alnova1 said:
I know this is a long shot but go to your dialer and input *#*#8778#*#* and make sure it looks like this pic. I fool with QPST and other things and sometimes forget to change the settings back to PDA and it will not mount. Long shot but what the hey...
Click to expand...
Click to collapse
Typed it in and got nothing. Using the android dialler when I pressed the last * the dialer cleared and did nothing.
Just installed the SDK so I could use (hopefully) ADB. When trying to install the Google driver rev4 windows says that rev 4 is no better than the one currently installed.
Also when I connect to the PC it says that the USB device is not recognised either.
I reckon my next thing to try flashing a new Rom via ROM manager.

well that didnt work in fact it has got considerably worse. I used ROM manager to download and install a new rom but didnt install the Gapps how daft do I feel now cos all I got is version of Blandroid running with no Android Market access to download ROM Manager.
I can access my WiFi network so I thought I would simply visit XDA via the mobile browser and download a fresh version of CM7 and then re-flash via ClockworkMod . However all I get is download fail error. I guess it doesn't know where to save the file.
So to recapp I have the following
a Nexus S (running Blandroid ROM)
a Win XP laptop that does not recognise my Nexus S (therefore cant install the Google driver to use ADB)
The Nexus S recovery is ClockworkMod and accessible.
I cannot accept that it is bricked (not just yet anyway)
I have another Laptop with Ubuntu installed. Will this help me in anyway to find a fix. I am not that experienced in Linux unfortunately.

1
i have the same problem. only thing you can try is.
pull out battery. let something metal touch the usb conecter .conecting the metal to a unload source(for static electricity.)
wait couple of hours,and try again.
if that didnt work.
2
open your nexus.
unplug all cables and screws from the main board.
again touch the usb conecter with something metal that has a ground source.
and try again.
the last step worked for me the 1st time pluging it in after i did that.
after that. usb didnt work again.
it probably has to do something with the usb phone charger and static electricity.
but i havent tested it.

will give that a try when I have a bit more time.
In the meantime I have been setting up ADB on my other laptop running Ubuntu 11.04. But unfortunately the Nexus S didnt register on the OS either. I thought you didnt need additional drivers for Linux only windows! I am really puzzled now as I thought the Linux option would have allowed me to flash a different ROM other than Blandroid (which isnt bad its just I dont have the Gapps installed)

maksymillian said:
will give that a try when I have a bit more time.
In the meantime I have been setting up ADB on my other laptop running Ubuntu 11.04. But unfortunately the Nexus S didnt register on the OS either. I thought you didnt need additional drivers for Linux only windows! I am really puzzled now as I thought the Linux option would have allowed me to flash a different ROM other than Blandroid (which isnt bad its just I dont have the Gapps installed)
Click to expand...
Click to collapse
you still have wifi/3G and CWM or bloothoot?
download the Gapps zip. put it on dropbox or any hosting site.download it trough your mobile browser and flash it trug CWM.
or use blutethoot to download it.
might be a short fix.until you get USB to work.
(this is how i do it cuz my usb doesnt work.)

I did try that but for some reason after stating that the download had started - Download Unsuccessful was displayed in the notification area. As useual I open a door only to find a brick wall on the other side.
In the meantime I am back with my HTC Hero.
Thanks for helping anyway!

maksymillian said:
I did try that but for some reason after stating that the download had started - Download Unsuccessful was displayed in the notification area. As useual I open a door only to find a brick wall on the other side.
In the meantime I am back with my HTC Hero.
Thanks for helping anyway!
Click to expand...
Click to collapse
try difrent download solutuins.
seeing you have HTC here.why not tranver your zip trug your hero to your Ns?(with bluethoot)

boy, i hope you haven't started tearing your phone apart yet...
since you still have access to cwm: try to format your sdcard with it. looks like you haven't done that yet.

I would try to uninstall all drivers and associated programs on your PC. Then reinstall the drivers. Windows can be very finicky as you know. Also try PDANET drivers.

ghost010 said:
try difrent download solutuins.
seeing you have HTC here.why not tranver your zip trug your hero to your Ns?(with bluethoot)
Click to expand...
Click to collapse
10 out of 10 - I just got my market back . downloading rom manager will shortly be back on CM7.
USB connection still not working yet but at least I got my account back on the NS and so the phone is usable

wild1z said:
I would try to uninstall all drivers and associated programs on your PC. Then reinstall the drivers. Windows can be very finicky as you know. Also try PDANET drivers.
Click to expand...
Click to collapse
The NS wouldn't connect to laptop with Ubuntu running. I am beginning to think that I have a faulty micro USB port.
Ill try the pdanet drivers later tonight - are they different from the google rev 4 drivers?

maksymillian said:
The NS wouldn't connect to laptop with Ubuntu running. I am beginning to think that I have a faulty micro USB port.
Ill try the pdanet drivers later tonight - are they different from the google rev 4 drivers?
Click to expand...
Click to collapse
Same PC with dual boot? Yeah, try another cord and a another PC. The fact that you plugged it in and it's recognized in some way in the tray says something is fubar. I just don't know if it is the phone though. Best of luck.

Nah, different laptop and different cable. Hope that it charges OK. Gonna have to get a WiFi file transfer app working to move files to and from.

glad to help out :3
there are allot of people that have this USB isue and its HW NS related. nothing we actually can do about it.plus it also happens after changing kernels and roms(i supose) overclocking might be 1 of the reasons thus the voltages not being original.
btw,sorry for my half assed english x3

Double check the modem/pda settings mentioned in post #3. Should be set to pda to see the files on the SD.

Moritzio said:
Double check the modem/pda settings mentioned in post #3. Should be set to pda to see the files on the SD.
Click to expand...
Click to collapse
Having the same issue. I tried that, no such luck.
My computer *did* connect at one point though... couldn't mount USB storage (wasn't prompted) but it did ask for a driver, and currently has a Samsug USB one installed. It won't accept the SDK driver (not 64-bit capable? Or NS4G? Idk...)

Moritzio said:
Double check the modem/pda settings mentioned in post #3. Should be set to pda to see the files on the SD.
Click to expand...
Click to collapse
I got nothing when I entered *#*#8778#*#*. I simply typed it in using the keypad on the dialer. Is there something else I should be doing?

[Q] SK4G not being recognized on PC

I originally posted this inside the Glorious Overdose V2 thread, but decided to post here as well.
For some reason my computer won't recognize my Sidekick when I plug it in via usb. I do have the samsung drivers installed and it will read my friends Samsung Droid Charge just fine, but when I plug my Sidekick in it comes up saying "USB Device Not Recognized". So far I've tried uninstalling and reinstalling the drivers from the device manager to no avail. Wondering if anyone has an idea as to what it could be. I've also tried googling the solution and everyone says to just uninstall and reinstall the drivers and it should work. Now the phone is not plugged into a USB Hub, extender, or case, it is plugged directly into a usb port on the mother board.
PC Specs just in case:
Motherboard - Gigabyte GA-970A-D3
OS - Windows 7 Ultimate x64
CPU - AMD FX-4100
Memory - 8GB DDR3 1066
Phone:
T-Mobile Sidekick 4G running Glorious Overdose V2
Nothing added just the rom and some apps/games.
I have tried with USB Debugging on and off, either way does not work.
Update: I have since tried Kies mini, as well as the drivers found on Softpedia. Neither of those worked, so I just got done reformatting and reinstalling Windows hoping that would work. At first it did not, right now I am running windows update to see if that was the issue, I'll update of what the outcome is.
Update: After installing all available Windows updates it's still not recognizing the phone. Now no matter what it's saying it's an Unknown Device. Even after I try and do a manual driver update and tell it to look in the folder with the driver files from Softpedia. I'm at a complete loss now.
If anyone has any idea's please let me know.

What mode do you have the phone in? Settings->Applications->USB Settings. It should be in Mass Storage if you want to access its SD Card.

Maybe put another rom on the sd card and flash something else, I don't think it would be a rom issue but it would be worth a try?
Sent from my SGH-T839 using XDA

Jax184 said:
What mode do you have the phone in? Settings->Applications->USB Settings. It should be in Mass Storage if you want to access its SD Card.
Click to expand...
Click to collapse
It's set to USB Debugging. But even then, it should read as something else other then Unknown Device when I plug it in. I have tried plugging it in and selecting Mass Storage, still comes up as Unknown Device.
HewettBR said:
Maybe put another rom on the sd card and flash something else, I don't think it would be a rom issue but it would be worth a try?
Sent from my SGH-T839 using XDA
Click to expand...
Click to collapse
I've thought about that, and from everything I can see it's either the ROM or the drivers. So we'll see...I'll probably try a different ROM and see what happens.

I suggest turning USB debugging off and mass storage on, for how you'll be using it. And recall that you have to change this stuff with the USB cable unplugged.

I've tried that, and after talking with the T2 Technical Support from Samsung for 45min today, the only option left is to send the phone in to get worked on. Though, I'm going into the T-Mobile store and see if they can't replace the phone or give me a loner while this one is out getting repaired.

More info request.
Can you provide us with the names and links to the drivers you have tried?

DuctTapedGoat said:
Can you provide us with the names and links to the drivers you have tried?
Click to expand...
Click to collapse
Kies Mini - http://www.samsung.com/us/support/owners/product/SGH-T839HABTMB
Softpedia - http://drivers.softpedia.com/get/MOBILES/Samsung/SAMSUNG-USB-Driver-1480.shtml
As well as the Samsung Vibrant drivers from both of those sites.

Samsung SideKick 4G Drivers
www DOT filedropper DOT com FWSLASH sk4gx64drivers
This is the exact drivers I pulled off of my own machine, I ran into massive issues with those same driver packages, especially in getting the initial root to take with a few different utilities designed to grant sudo/su/root access, and these are the drivers I have running currently, just pulled off my own machine. I run Windows 7 x64, but as well, there should be no reason why these drivers wouldn't work on a x86 machine and/or OS.
NOTE : I apologize it's not a proper link, but I'm unable to post a raw link until I hit my 8th post. I will come back and fix this after I hit that 8th post, but until then it will be ghetto-bypass HTML.

DuctTapedGoat said:
www DOT filedropper DOT com FWSLASH sk4gx64drivers
This is the exact drivers I pulled off of my own machine, I ran into massive issues with those same driver packages, especially in getting the initial root to take with a few different utilities designed to grant sudo/su/root access, and these are the drivers I have running currently, just pulled off my own machine. I run Windows 7 x64, but as well, there should be no reason why these drivers wouldn't work on a x86 machine and/or OS.
NOTE : I apologize it's not a proper link, but I'm unable to post a raw link until I hit my 8th post. I will come back and fix this after I hit that 8th post, but until then it will be ghetto-bypass HTML.
Click to expand...
Click to collapse
Thank you, I tried unpacking them to a folder on C:\ went into Device Manager, right clicked on the Unknown Device, Update Driver Software..., Browse My Computer for Driver Software, Set the search to C:\, and still saying Unknown Device is the best driver software for it. No idea why it's doing this.

Proper Driver Update
What is going on is that Windows is seeing a more recent signature file attached to the SK4G drivers on your computer (I don't believe anything at all is wrong with your device) than the working ones there.
First, in Add/Remove Programs, uninstall the Samsung Kies and Samsung Driver pack you installed earlier. Now...
Go into on your PC:
://windows/system32
And locate the same file names, cut them all, and paste them in a temporary folder you create, preferably on the desktop or something similar. You may not find every file, and that's okay, just the ones you can find. Next, you will be wanting to paste the driver files from the package I uploaded. Now, turn off Automatic Updates, so it doesn't automatically install drivers upon connection. Reboot the computer, double check and make sure Automatic Upates are off when you log back on. Now, connect the device and see if it gives you the same results. By removing the old drivers which don't work, you'll be able to force it to the ones we know work, and you /should/ have success. As well - USB data debugging active and activating connection for data transfer via the notification pulldown menu would be the best way to do this initially.

Would I be looking in c:\windows\system32\drivers for the same file names as the ones you packed up?

Ok, so the only one I could find in the drivers folder was modem.sys. But it will not let me move/replace the one that's already in there. It's telling me access is denied, same thing when I try and set the permissions it will not let me. I am logged in as an Administrator, as well it says it when I log in as THE Administrator account. So yeah...

Cool - modem.sys is a stock one that is shared with the device, so that's fine.
With the other two programs uninstalled, the old drivers uninstalled, and forcing it into those by pasting them into //win/sys32/drivers you should be in business. Hmm. You can try UnlockRoot.com's device rooter - I know they have an auto driver detector in their program. As well, you can try SuperOneClick, but I don't remember if they do or no. What about going in from the Recovery menu and toggling USB? Anything wierd going on in the /mounts? What about ADB shell access from the Android SDK on Windows?

DuctTapedGoat said:
Cool - modem.sys is a stock one that is shared with the device, so that's fine.
With the other two programs uninstalled, the old drivers uninstalled, and forcing it into those by pasting them into //win/sys32/drivers you should be in business. Hmm. You can try UnlockRoot.com's device rooter - I know they have an auto driver detector in their program. As well, you can try SuperOneClick, but I don't remember if they do or no. What about going in from the Recovery menu and toggling USB? Anything wierd going on in the /mounts? What about ADB shell access from the Android SDK on Windows?
Click to expand...
Click to collapse
I tried plugging the phone in, still showing up as Unknown Device. Tried UnlockRoot.com's program, no change. Installing the Android SDK right now, as well as I tried deleting the INFCACHE.1 file, and no change with that either. Once I'm done installing the Android SDK I'll redelete the INFCACHE.1 file and restart and try the phone again.
I did go in and check the mounts in recovery and they were set to:
UNMOUNT CACHE
MOUNT DATA
UNMOUNT SDCARD
UNMOUNT SYSTEM
Thank you for your help so far.
UPDATE: So after installing the Android SDK, deleting the INFCACHE.1 file, restarting, and then plugging the phone in, comes up and says the USB Device is Not Recognized. Then goes to search the preconfigured driver folders, and fails to install the driver for Unknown Device. And ADB Devices shows no devices as well(didn't think it would, but yeah).
UPDATE: So after using my friends phone as a conduit to throw the Stock Odexed KJ2 w/ Root(http://forum.xda-developers.com/showthread.php?t=1328698) onto my SDCard and flashing that the phone seemed to go into a soft brick at pre-boot screen(where it says SAMSUNG T-Mobile blah blah blah). Mind you this would freeze before it was even able to get into recovery. So I took it into T-Mobile and they are doing a manufacturer warranty replacement. So hopefully this next phone will be able to connect to the computer and be read correctly.