Hi Folks
Well, here it is, ported from what I did for the Polaris basically... I find it's a nice solution as it works by flashing your device with a patched radio and changing stuff properly, anyway...
download and run the EXE, follow the instructions.
bear in mind if you already have Hard-SPL on your device you can skip *straight* to Step 2.
and remember the golden rule:
YOUR DEVICE MUST BE IN CE AND SYNCED BEFORE RUNNING EACH STEP.
Download Here or Download Here
UPDATE: now version v2.0 - Model ID error fixed, it WORKS.
if and when you get success, POST!
PS: If you try to sell this, I will find you, kill you, and sell your ****ing testicles on eBay
Yes, apologies, my error, new version uploaded
So what is the status now?
I found this solution does not work on all of devices. But my solution is as follows.
Run KaiserUnlocker.exe
1. I started with the Step 1. The upper button of total 3.
2. Go through the menus and accept everything.
3. You get TRI-COLOR screen on your device and a few seconds later you get the USB label.
4. After some time you get a communication error Message. DON'T RESET YOUR MOBILE DEVICE. DON'T TOUCH IT.
5. Press Exit to quit KaiserUnlocker.exe on your Desktop machine.
6. Unplug and replug the USB cable.
7. Start the KaiserUnlocker.exe again and wait a little bit.
8. Your mobile device (AT&T Tilt) suddenly alive again. The progressbar shows up and you're from 0% to 100% in a few seconds. Wait a little bit and then you get the message the process is finished.
Now I don't know what to do with step 2 and 3. Should I perform them or not. Hmm?
What I would like to do is just to update from AT&T Tilt ROM to original HTC TyTN II ROM
AS I said before.
REDOWNLOAD IT.
I just tested the flash on my Kaiser, it's fine, no pissing Model ID error at all.
however, to avoid any confusion, download AGAIN and this time you'll find that the version in the debug output is changed to v2.0
so if you don't see v2.0, you don't have the new one
Oh I see you changed the version now. At the time I downloaded it and wrote my first message it was just V1. There was no V2. But I can't test it now because I already have the ROM patched.
And I didn't get the ModelID error. It was a connection error 260.
I think it's just some guys of you are lucky to have a device that doesn't get the white screen when using hardspl and it doesn't stop on tri-colors or the progressbar at 0%.
actually, it's steps 2 and 3 that I care about, having a patched ROM is irrelevant.
step 2 and 3 allow you to sim/CID unlock
Mirror:
Kaiser Unlocker v2.0
FTP Problems!
Hi everybody,
Our provider has notified us of the fact that our ftp server has appeared in a list of compromised FTP servers which are known to host malware associated with attacks on banks and banking infrastructure. We have been requested to secure our systems. Since we realize it would cause serious problems to some if not most of our users if we we're to close it down immediately or change the password in the next 5 minutes we hope you can all live with the following arrangement:
We will close down the ftp server Monday the 9th of march on 09.00 CET. You have until then to download anything from our ftp server you (urgently) need, especially if you host software of which you don't have a back-up on our ftp it's important to download it asap. After closing down our server upcoming Monday we will remove all malware and start restructuring our server, implementing a new user structure, this does mean our server will be offline for a while and we cannot assure you no data will be lost.
If you have space available to host your own software please do so, if you have space available for those who do not have their own space please let it be known by posting a reply to this post. Our apologies for any inconvenience this will cause, but we hope to be able to serve you with a better ftp server as soon as possible.
Best regards,
Flar
Site admin.
Click to expand...
Click to collapse
Just to be safe!
Thanx Olipro
Sorry for asking, what do you mean by "your device must be in CE"?
Olipro said:
AS I said before.
REDOWNLOAD IT.
I just tested the flash on my Kaiser, it's fine, no pissing Model ID error at all.
however, to avoid any confusion, download AGAIN and this time you'll find that the version in the debug output is changed to v2.0
so if you don't see v2.0, you don't have the new one
Click to expand...
Click to collapse
I did re-download after you said it didn't work. I must have downloaded it before it was fully uploaded. I did see the V2.0 NOw...this time no errors.
Thanks again Works perfect now. Thank again.
It Works!
This is awesome. I was trying with Jocky's unlocker for couple of hours. No luck.
Gave a try to this tool. Unlocked first time. Now, I got to check my phone with a different provider SIM.
Thank you so much!
Done, but I saw that you have change the radio version to 1.70.xxx. What radio is this?
Does this mean that the unklocker installs Hard SPL permanently - so future rom flashes are possible? what does device in CE mode mean?
Penske MB said:
Done, but I saw that you have change the radio version to 1.70.xxx. What radio is this?
Click to expand...
Click to collapse
it's 1.58.something, i forget the rest
FTP will close today.!!!!!!!!!!!!!!!!
I try to download and uploade to mediafire
Midget Edit: Mirror removed, new version.
doesn't matter, I'm updating the FTP link in a second or two with the new one
Active sysnc
Hi Olipro,
Thanks for all the hard work.
When I try to run the step 1, it keeps on disconneting the active sysnc. Am I doing something incorrectly?
Cheers
Shan
elmoono said:
Does this mean that the unklocker installs Hard SPL permanently - so future rom flashes are possible? what does device in CE mode mean?
Click to expand...
Click to collapse
These were my steps,
1. Identified my AT&T radio ROM & downloaded that from XDA website as a backup. Pick from here
2. Ran Pof's HardSPL Link
3. Ran Jocky's SuperCID & Security Unlocker Link
4. Installed Dutty's Official WM6.1.2.19199 Full Version Link
5. Installed Radio ROM 1.64.06.04 Download
6. Installed .NET Framework 2.0 on my Windows XP SP2 from Microsoft website.
7. Ran OliPro's Kaiser SIM/CID Unlocker. Followed just step 2 & 3 since I had already installed HardSPL.
8. Installed Radio ROM 1.64.06.04 to get my ringtone & HSDPA connection.
May be my steps 3 ~ 5 were over kill but that was just me. If you would like to skip 3 ~5 make sure you have WM 6.1 installed also remember to patch your original radio on step 8.
All the above steps does not need a strange SIM. I am yet to pop in a different carrier SIM to confirm about my Tilt Unlock Status. However, after the above steps, I found "Kaiser Unlock.exe" under my Tilt root folder. I ran that from phone, clicked on check SIM Status, came up as "You are already SIM Unlocked"
Hope this helps.
when you run step 3, just query what simlocks are active
Worked on my AT&T Tilt!
Not sure about step one already had SPL done with Whitescreen Fix
I will try it monday when my friend brings his tilt over to get it unlocked.
I did have to install a 6.1 ROM (I used Dutty's Official) between steps 2 and 3, had a blank screen, using the att rom -bloatware.
Related
99% of your questions can be answered by the wiki.
The main points are below. Please try and follow these instructions yourself before you start asking the questions everyone asks every week (sometimes every day) somewhere on this forum
Detailed Instruction On How To Upgrade with Bootloader method
Instructions for those stuck on Boot Screen
Instructions for those with Country Code error
Upgrade bootloader from 1.00 to 1.01
Instructions for those stuck on Boot Screen (UNI_exitbootloader)
If you have genuine problems that are not solved by reading these solutions, and performing the steps they say, then by all means, ask the question, but please, please please, don't fill the forum with useless questions that have been answered hundreds of times already.
Thanks for your help. but, i got errors with your link.
Sorry but they all work fine for me. Which link in particular are you having problems with?
All links are working fine here.
Nice job !!
Not my work, I'm just linking to the wiki pages that people are to stupid and lazy to look for themselves
So, the problem is me or my machine.. donna know...
By the way, upgrading bootloader is not necessary - everything works with BL 1.00
mamaich said:
By the way, upgrading bootloader is not necessary - everything works with BL 1.00
Click to expand...
Click to collapse
thats interesting, someone reported to me that 1.00 wasn't working (i have 2.01 so dont know )
OFF TOPIC:
how can i extract a bootloader dumped to sd card in windows or mac or linux? (preferably mac or linux cause they have sd card readers and i can't find my usb one)
Just to confirm that mine's still working fine with Bootloader 1.00 (as if anyone would doubt Mamaich!)
freezing problem with ActiveSync 4.2
Do not connect the Universal to your desktop unless you have ActiveSync 4.5 installed in the desktop or it will freeze your device.
Disable ActiveSync connection in Universal until ActiveSync is updated.
ActiveSync 4.5 beta 2
http://www.redirectto.com/?go=645c1c6e5b
Regarding instruction 7:
# Put the Universal in bootloader mode by pressing Power + Light + Reset, which brings up an un-backlit screen with "Serial" at the top, and "v0.XX" at the bottom. (A lot of people get an error message if they are not in bootloader mode. They can install the ROM a second time. If you are in bootloader mode, you won't get an error message.)
I dont get what you mean by press Power + Light + Reset? Are you talking about the button on the phone? On my O2 XDA Atom Exec there is no light button..cuz when i open the bootloader exe it goes this is not a valid win 32 program. Bootloader is not meant to be opened from the PDa but from your computer but i cant open it.
>> # Put the Universal in bootloader mode by pressing Power + Light + Reset
> On my O2 XDA Atom Exec there is no light button..cuz
So, is an O2 XDA Atom Exec an HTC Universal then?
ivorh said:
>>
> On my O2 XDA Atom Exec there is no light button..cuz
[/b] then?
Click to expand...
Click to collapse
Probably why it doesnt work..so i cant upgrade to WM6? I realyl dont get why Australia only have the ATOM and not the Exec?
Quick Question
I upgraded to WM6CB which I aquired from torrentspy, and the upgrade was sucessful. The device turns on after upgrade, and the extROM loads up. After the reset, a window pop-ups saying that I have illegally aquired this ROM. Im not sure what I did wrong. I used the maUpgrade file aswell. Any help is appreaciated.
davidw89 said:
Probably why it doesnt work..so i cant upgrade to WM6? I realyl dont get why Australia only have the ATOM and not the Exec?
Click to expand...
Click to collapse
In Australia, The HTC Universal is branded as the I-Mate Jasjar.
Cheers,
Ray.
neptune said:
I upgraded to WM6CB which I aquired from torrentspy, and the upgrade was sucessful. The device turns on after upgrade, and the extROM loads up. After the reset, a window pop-ups saying that I have illegally aquired this ROM. Im not sure what I did wrong. I used the maUpgrade file aswell. Any help is appreaciated.
Click to expand...
Click to collapse
I've never seen that, sounds like someone's either added in that popup as a joke, or it's from a ROM dump of one of the RTM or MVP builds, and your devices IMEI is different to the one it was for.
I know MVP's had the option of getting Crossbow, but they had to send their device to Microsoft to have it flashed. Perhaps these builds have something coded to the IMEI.
used BL 0.60 successfullty
Midget_1990 said:
thats interesting, someone reported to me that 1.00 wasn't working (i have 2.01 so dont know )
OFF TOPIC:
how can i extract a bootloader dumped to sd card in windows or mac or linux? (preferably mac or linux cause they have sd card readers and i can't find my usb one)
Click to expand...
Click to collapse
I could use BL 0.60 successfully
Hi!
I have using it for 2 days. Initailly it seem difficult to install soft. But now easer, the RAM still down like WM 05, Soft Reset time quite longer then Ivan test 2's ROM. But the icon look very nice.
Alan, i think u should add the solution for "stuck in the bootloader" problem, by using UNI_exitbootloader.exe. this is much simple than using mtty IMHO.
Please don't flame me but I've got a n00b question for you.
This is my first GSM phone as I've just come off of a CDMA network so I've never flashed a ROM before. I've gone through a lot of the posts that I've seen on the forum and on the wiki and I just want to clarify steps before I brick my phone.
I just picked up a new AT&T Tilt w/out the camera yesterday and I'd love to experiment with the new ROM that Dutty just released. Here are the steps as I understand them:
1) Download HardSPL for Kaisers onto my Vista computer
2) Attach the data cable from my computer to my Tilt and verify that the ActiveSync icon is green
3) Run kaiser-hardSPL.exe from the computer
4) After this has completed execute a HardReset
5) Download the Dutty's DualTouch v1.1 Rom to my Vista computer
6) Keeping the data cable attached verify that the ActiveSync icon is still green
7) Run the Kaiser_RUU.exe from my computer
8) Perform a HardReset again
9) Keeping the data cable attached verify that the ActiveSync icon is still green
10) Download the 1.27.12.17 version of the radio since I'm currently on .11.
11) Decompress the package
12) Run the CustomRUU.exe
13) Perform a HardReset
14) Go to Dutty's site, click on the paypal link, and show the love!
After this everything should work. Will I need to perform the keyboard fix at this time or is that already incoporated? Have I left any steps out? Anything in here completely wrong? Any suggestions what so ever?
Thanks in advance!!!
sounds like u have it all figured out. good job.
and yes, install the keyboard fix.
Any potential issues since I haven't "unlocked" the phone?
none that i know of. good luck.
Outstanding!!! Thank you for giving me a sanity check.
glad i could help. good luck w/ the roms. once youve done 1 it gets alot easier. just dont forget to hard reset. i did and had to flash all over.
Attached you find all you need to flash cooked ROMs on your Ozone (Cedar).
The sspl/hardspl are confirmed to work fine on the HTC Cedar platform (Ozone).
It will not work on the HTC Maple platform (Dash3G). Running this sspl on a Dash3G will definitely brick it. Also the HTC Willow platform (SNAP S511, Sprint) is not supported. For the Dash3G I have already developed a sspl/hardspl. Users of the S511 have to wait until I feel motivated ..
The packages contains a SSPL, HardSPL, patched ROM updater and the original Ozone SPL. The package is based on SPL v0.39
Instructions:
1. remove SD and SIM cards (don't forget otherwise the sspl is likely not to work!!)
2. connect your device to your pc with a USB cable and wait until it is synced
3. extract the file "Ozone HardSPL by JockyW.zip" and execute "auto.bat"
4. follow all instructions given on screen: first the sspl is copied to the device and executed. You must confirm running JumpSPL on the device: first time you must click Yes to allow it to run, you also must click the trackball to continue execution of JumpSPL. The device display will turn dark and after that the romupdate tool will install the hardspl on your device. (the identification string in the tri-color bootloader screen is "0.39.Hard")
5. to test the sspl and the hardspl you can flash the attached splash.nbh
Once the HardSPL is installed on your device you can flash any Ozone cooked or original ROM.
Have fun,
JockyW
PS: Moderators please make this a sticky. Thanks.
Awesome work JockyW.
Awesome, thanks for your hard work.
Now all we need are some 6.5 roms!
4. follow all instructions given on screen: first the sspl is copied to the device and executed. You must confirm running JumpSPL on the device: first time you must click Yes to allow it to run, you also must click the trackball to continue execution of JumpSPL. The device display will turn dark and after that the romupdate tool will install the hardspl on your device. (the identification string in the tri-color bootloader screen is "0.39.Hard")
Click to expand...
Click to collapse
Um... so most of this worked fine, and the screen is dark, and a generic htc driver got auto installed... and the Rom Utility popped up on my screen... But how do I get it to connect to activesync like this?
After my phone rebooted completely (following the ROM utility completing), I just re-enabled Allow USB connections and it seems to work fine.
No, so the rom update tool doesnt complete because ActiveSync doesnt work after the screen turns black...
Edit: and Im using XP (noticed ur not from the thumbnail...) idk if that matters or anything
I'm having some difficulties of my own. I'm running Windows 7 RC x64 with WMDC 6.1.6965.
I started by running the sspl.bat (with USB enabled in WMDC); the SPL app came up on my device's screen, I tapped ok, and the device screen went black w/ solid black pixels. The only way of rebooting it is yanking the battery. The OS loads fine after that.
Later I thought it had run sucessfully so I ran auto.bat. The JumpSPL steps ran fine (with USB enabled still) but it failed at step 4 when the ROM tried to flash (obv. because USB was still enabled).
Strange thing is, when USB is disabled and I run auto.bat, the device is unable to connect in steps 1-3. I canceled all those steps and then the ROM flasher starts, makes a connection, and starts the flash but won't go past 0%. The screen is still black because after step 3 the SPL flashes (or attempts to.)
I later put the device in bootloader manually (with the colorful bars) and ran the ROM flasher by itself. It runs but again, gets stuck at 0% on both the device and the PC. After a while a 262: update error pops up. This must be because the SPL is still locked? The OS boots fine after a battery pull.
Strange. Any advice would be welcome.
forgot to remove my SIM card! Gonna try again, give me a few minutes
no, same problems. :sigh:
The bootloader is still locked in 0.39.0000, confirmed.
EDIT: I'm pretty sure all my problems are coming from x64 drivers. I'm going to try this again in Windows XP Mode. Congrads everyone who's succesfully flashed! Good work guys!
businesschild said:
forgot to remove my SIM card! Gonna try again, give me a few minutes
Click to expand...
Click to collapse
businesschild said:
I'm having some difficulties of my own. I'm running Windows 7 RC x64 with WMDC 6.1.6965.
I started by running the sspl.bat (with USB enabled in WMDC); the SPL app came up on my device's screen, I tapped ok, and the device screen went black w/ solid black pixels. The only way of rebooting it is yanking the battery. The OS loads fine after that.
Later I thought it had run sucessfully so I ran auto.bat. The JumpSPL steps ran fine (with USB enabled still) but it failed at step 4 when the ROM tried to flash (obv. because USB was still enabled).
Strange thing is, when USB is disabled and I run auto.bat, the device is unable to connect in steps 1-3. I canceled all those steps and then the ROM flasher starts, makes a connection, and starts the flash but won't go past 0%. The screen is still black because after step 3 the SPL flashes (or attempts to.)
I later put the device in bootloader manually (with the colorful bars) and ran the ROM flasher by itself. It runs but again, gets stuck at 0% on both the device and the PC. After a while a 262: update error pops up. This must be because the SPL is still locked? The OS boots fine after a battery pull.
Strange. Any advice would be welcome.
Click to expand...
Click to collapse
businesschild said:
no, same problems. :sigh:
Click to expand...
Click to collapse
businesschild said:
The bootloader is still locked in 0.39.0000, confirmed.
Click to expand...
Click to collapse
Instead of replying to yourself, please use the edit button next time.
Anyways, if you run auto.bat, disable USB Connections after the screen turns black via ActiveSync. In your device manager (with the screen still black) look at your USB Devices. You should see a entry called HTC USB Sync. If you see that continue to flash. Seeing HTC USB Sync is a key step in this whole process.
Please read the testing/development thread for some good solid help. A bunch of us ran into the same issue you did. If you read all 4 pages you should be able to troubleshoot your problem: http://forum.xda-developers.com/showthread.php?t=550628
computerpro3 said:
Awesome, thanks for your hard work.
Now all we need are some 6.5 roms!
Click to expand...
Click to collapse
Working on it! Lots of work! Gonna grab my Ozone later today and cook you guys up some treats to taste test! Haha. Ready??
ookba said:
Working on it! Lots of work! Gonna grab my Ozone later today and cook you guys up some treats to taste test! Haha. Ready??
Click to expand...
Click to collapse
I'm a new member here and I can't believe how much hard work you guys put in for free. I am pretty broke right now but at some point in the next week or so I'm going send a small donation to both you and jockyw....won't be much as I really can't afford it but should buy you some decent beer at least...
computerpro3 said:
I'm a new member here and I can't believe how much hard work you guys put in for free. I am pretty broke right now but at some point in the next week or so I'm going send a small donation to both you and jockyw....won't be much as I really can't afford it but should buy you some decent beer at least...
Click to expand...
Click to collapse
HERE HERE!
The stock ozone rom is crap, I would love to cook my own ROM!
BTW hardspl successfully flashed first try on my device. Totally painless. Excellent job.
Anyone with a Telus SNAP try this?
ariesq said:
Anyone with a Telus SNAP try this?
Click to expand...
Click to collapse
I think the Telus SNAP is a CEDAR as well. Uses the same CDMA network as Verizon. Dump your SPL and post it for JockyW to examine and give the tumbs up.
Also, dump your RAW files, upload and post in this thread if you can.
http://forum.xda-developers.com/showthread.php?t=540586
Also guys, we gotta hook up JockyW with some donations. He worked his ASS off to build this and we have to show some gratitude. If you want him to continue to support us, we have to show him some love.
ookba said:
Also guys, we gotta hook up JockyW with some donations. He worked his ASS off to build this and we have to show some gratitude. If you want him to continue to support us, we have to show him some love.
Click to expand...
Click to collapse
I agree. Just sent him a small donation. You're next ookba, but will have to wait until next paycheck.
Update: Small donation sent to you as well ookba. I'll just have to skip lunch tomorrow
P
How sure are you that Ozone is Cedar?
RUU_Chief_W_WM65_VERIZON_WWE_2.10.605.1T_Radio_612522_1.71.00WV_NV_MFG_VZW
looks like a chief to me, but I could be wrong, I would like to release a 6.5 kernal, but dont want to have wrong device.
Attached you find all you need to flash cooked ROMs on your HTC Snap 511 (Willow).
The sspl/hardspl are confirmed to work fine on the HTC Willow platform (HTC Snap 511).
It will not work on the HTC Maple platform (Dash3G). Running this sspl on a Dash3G will definitely brick it. Also the HTC CEDAR platform (Ozone) is not supported. For the Dash3G and Ozone I have already developed a sspl/hardspl.
The packages contains a SSPL, HardSPL, patched ROM updater and the original Snap S511 SPL. The package is based on SPL v0.34
Instructions:
1. remove SD and SIM cards (don't forget otherwise the sspl is likely not to work!!)
2. connect your device to your pc with a USB cable and wait until it is synced
3. extract the file "Snap S511 HardSPL by JockyW.zip" and execute "auto.bat"
4. follow all instructions given on screen: first the sspl is copied to the device and executed. You must confirm running JumpSPL on the device: first time you must click Yes to allow it to run, you also must click the trackball to continue execution of JumpSPL. The device display will turn dark and after that the romupdate tool will install the hardspl on your device. (the identification string in the tri-color bootloader screen is "0.34.Hard")
5. to test the sspl and the hardspl you can flash a splash screen
Once the HardSPL is installed on your device you can flash any cooked or original ROM.
A donation for my work would be highly appreciated
Have fun,
JockyW
PS: Moderators please make this a sticky. Thanks.
Donation
Donation has been sent. Thank you for this.
Good work!!!!
Thanks Jocky, sending you good vibes and tips!
Once we install the hardSLP on the sprint snap, which cooked roms can we use? Are we going to need one specially cooked for the snap 511?
dougmwpsu said:
Thanks Jocky, sending you good vibes and tips!
Once we install the hardSLP on the sprint snap, which cooked roms can we use? Are we going to need one specially cooked for the snap 511?
Click to expand...
Click to collapse
Yes, ookba is waiting to get his own phone to get a ROM working... Donations really speed up that process
Should this be stickied like the last few? Maybe consolidate all into one?
Black_V!per said:
Yes, ookba is waiting to get his own phone to get a ROM working... Donations really speed up that process
Should this be stickied like the last few? Maybe consolidate all into one?
Click to expand...
Click to collapse
Anyone care to donate their S511 to me for a week or so?
ookba said:
Anyone care to donate their S511 to me for a week or so?
Click to expand...
Click to collapse
Maybe the next week I'm on vacation... can the phone be service deactivated while you have it?
dougmwpsu said:
Maybe the next week I'm on vacation... can the phone be service deactivated while you have it?
Click to expand...
Click to collapse
Sure it can. Where are you though?
ookba said:
Sure it can. Where are you though?
Click to expand...
Click to collapse
Raleigh, NC. My next vacation isn't till the week of Christmas though, so maybe someone else can step up in the meantime. I'll also be out of the office again for a week in the spring.
first off, thanks so much to Jocky and Ookba for all the work you guys do! but i'm having some issues. i've dont a lot of searching on here and i can't find a solution hopefully someone can help me. i can't get the hardspl to run successfully.
my bootloader screen shows this:
CEDA200
SPL-0.34.0000
MicroP-Willow#C (LED) v58B
i'm using windows 7 (through VMWare on my iMac), everything seems fine until the pop up on the phone, i click the button (the not really a trackball button) and the screen goes black, i lose all connectivity through WMDC and the Rom Utility gets error 266.
If i don't click when the pop up shows on the phone, the Rom Utility will show and then the phone will go into the bootloader with USB written in the white area then i get the error 266 again.
of course there's no sim because it's a Sprint s511, and the sd card is always removed.
what can i do? i'd really love to get 6.5 on there, but i'm at a loss.
The fact that your running on a MAC with VMWare makes me think the issue could be in the connection...
Im not even sure if Win7 works, i could be wrong however. You wouldnt happen to know of anyone that has a WinXP machine would you?
I did try in vmware with XP and Activesync, but it did the same things. I have a Dell that I was gonna make a hackintosh, but I'm gonna throw xp on it and try using that machine. I was thinking it was the vmware too, i guess i just wanted one of you guys (you know, the one's with a clue! LOL) to confirm.
I applied the HardSPL to my snap using Windows 7 and everything went well
robconway said:
I did try in vmware with XP and Activesync, but it did the same things. I have a Dell that I was gonna make a hackintosh, but I'm gonna throw xp on it and try using that machine. I was thinking it was the vmware too, i guess i just wanted one of you guys (you know, the one's with a clue! LOL) to confirm.
Click to expand...
Click to collapse
Thats what it sounds like... Good to know it works on Win7 though SPIK3.
Thanks Black_V!per for responding and all. I did finally get it going! I set up the dell with XP and it actually didn't work at first. I had originally unRARed the package on the iMac and just copied the unarchived folder over to the XP machine, thinking it would save me a download, but it didn't work. So i just dl'd an RAR utility for windows and unpacked the RAR on the xp machine and it worked perfect. originally the Rom Updater said it couldn't find the nbh file. all's well! And i'm loving 6.5!!
Thanks again Jocky and Ookba!!!
robconway said:
Thanks Black_V!per for responding and all. I did finally get it going! I set up the dell with XP and it actually didn't work at first. I had originally unRARed the package on the iMac and just copied the unarchived folder over to the XP machine, thinking it would save me a download, but it didn't work. So i just dl'd an RAR utility for windows and unpacked the RAR on the xp machine and it worked perfect. originally the Rom Updater said it couldn't find the nbh file. all's well! And i'm loving 6.5!!
Thanks again Jocky and Ookba!!!
Click to expand...
Click to collapse
Must have corrupted during the download... Havent seen that since my 56k-days.
Glad to hear that!
First off, I appreciate everyone's hard work throughout this whole process.
Unfortunately I am running into a problem. The auto.bat is able to copy the JumpSPL file and the .nb file to my phone just fine. However once the Rom Update Utility starts the flashing process, the phone shuts off.
I did a hard reset to my phone, and went through the process again. The JumpSPL notice popped up on the screen, but then crashed when I hit OK. I know it crashed because the Windows Error Reporting popped up (which apparently I had disabled before I did the hard reset, so I never was able to tell if it was still running).
So then I manually ran the JumpSPL file. This time the memory box popped up, so I hit OK with the Jump Address at the default 0x00000000. It then asked which SPL file I wanted to use. I chose the .nb that was copied over. Then the Windows Error Reporting screen showed up again.
I'm not sure what is going on, but hopefully the details I just provided will allow someone to figure something out. Thanks.
BTW: My phone is a Sprint HTC Snap S511, and my splash screen is the same as the one posted before:
CEDA200
SPL-0.34.0000
MicroP-Willow#C (LED) v58B
Jaymoon said:
First off, I appreciate everyone's hard work throughout this whole process.
Unfortunately I am running into a problem. The auto.bat is able to copy the JumpSPL file and the .nb file to my phone just fine. However once the Rom Update Utility starts the flashing process, the phone shuts off.
I did a hard reset to my phone, and went through the process again. The JumpSPL notice popped up on the screen, but then crashed when I hit OK. I know it crashed because the Windows Error Reporting popped up (which apparently I had disabled before I did the hard reset, so I never was able to tell if it was still running).
So then I manually ran the JumpSPL file. This time the memory box popped up, so I hit OK with the Jump Address at the default 0x00000000. It then asked which SPL file I wanted to use. I chose the .nb that was copied over. Then the Windows Error Reporting screen showed up again.
I'm not sure what is going on, but hopefully the details I just provided will allow someone to figure something out. Thanks.
BTW: My phone is a Sprint HTC Snap S511, and my splash screen is the same as the one posted before:
CEDA200
SPL-0.34.0000
MicroP-Willow#C (LED) v58B
Click to expand...
Click to collapse
Is your phone applications unlocked? When I did mine it gave me a bunch of errors because it wasn't applications unlocked. Also make sure you remove your memory stick.
SPIK3 said:
Is your phone applications unlocked? When I did mine it gave me a bunch of errors because it wasn't applications unlocked. Also make sure you remove your memory stick.
Click to expand...
Click to collapse
How would I go about checking this?
I remember on my Samsung Ace, before the 6.1 update, I had to install an "application unlocker" that allowed unsigned programs to install. Is this the same thing with the Snap? Also this is the Sprint version, so I don't have a Sim card, or anyway to typically "unlock" this phone.
EDIT: Ah, now I know what you mean. I found the SDA Application Unlock here: http://forum.xda-developers.com/showthread.php?t=563761
The Rom Update Utility finished successfully! Now to move on to the next step... Thank you SPIK3
No problem, glad I can help.
I am very new to flashing ROM's on phone, i have read thru most of the related threads and followed the steps with no sucess. Appreciate if someone can help me with detailed steps
Mobile - T-Mobile HTC Touch Pro2
OS - Win 6.5 (T-Mobile ROM)
RHOD210 32M MI-BC
SPL-0.87.0000
PC Details - WinXP with Active Synch
Queries on HARDSPL
Downloaded CDMA HARDSPL (RhodiumW-HardSPL_V1_10R3) and tried to do a automatic flash (while it is starting the application) the following message is displayed on the phone "This package is not intended for your device type, high chance of bricking exiting now" clicked ok on the phone and tried to continue (also during this time the Active sync disconnects and does not connect later, i have to unplug the usb) the install and it has been at 0% for 2-3 min and i get the error 262. I tried running the HARSPL in admin mode but still no luck
After spending some time reading the threads i decided to do the SSPL Manal "SSPL-Manual-RhodiumV1_10", i followed the instructions and copied the exe to the phone (in the windows explorer>mobile folder) but i am unable to run the exe on the phone (don't know what i am doing wrong).
1. Am i using the correct HARDSPL? Please send me the correct steps and point me to correct HardSPL.
2. If the Active Synch is disconnected, will the Hardspl still work
3. I have also read about Task29, do i have to run this after hardspl
vuday_raj said:
I am very new to flashing ROM's on phone, i have read thru most of the related threads and followed the steps with no sucess. Appreciate if someone can help me with detailed steps
Mobile - T-Mobile HTC Touch Pro2
OS - Win 6.5 (T-Mobile ROM)
RHOD210 32M MI-BC
SPL-0.87.0000
PC Details - WinXP with Active Synch
Queries on HARDSPL
Downloaded CDMA HARDSPL (RhodiumW-HardSPL_V1_10R3) and tried to do a automatic flash (while it is starting the application) the following message is displayed on the phone "This package is not intended for your device type, high chance of bricking exiting now" clicked ok on the phone and tried to continue (also during this time the Active sync disconnects and does not connect later, i have to unplug the usb) the install and it has been at 0% for 2-3 min and i get the error 262. I tried running the HARSPL in admin mode but still no luck
After spending some time reading the threads i decided to do the SSPL Manal "SSPL-Manual-RhodiumV1_10", i followed the instructions and copied the exe to the phone (in the windows explorer>mobile folder) but i am unable to run the exe on the phone (don't know what i am doing wrong).
1. Am i using the correct HARDSPL? Please send me the correct steps and point me to correct HardSPL.
2. If the Active Synch is disconnected, will the Hardspl still work
3. I have also read about Task29, do i have to run this after hardspl
Click to expand...
Click to collapse
1. no, you have a RHOD210, so you need this one: http://forum.xda-developers.com/showthread.php?t=550131
2. activesync is needed when you start the Hard-SPL exe but after that at one point it will go off, that's normal.
3. not really, except if you flash a ROM and you have weird issues. then it can be helpful to reformat the OS+data area.
cmonex said:
1. no, you have a RHOD210, so you need this one: http://forum.xda-developers.com/showthread.php?t=550131
2. activesync is needed when you start the Hard-SPL exe but after that at one point it will go off, that's normal.
3. not really, except if you flash a ROM and you have weird issues. then it can be helpful to reformat the OS+data area.
Click to expand...
Click to collapse
Thanks for the suggestion, it worked like a dream but when i tried to install the custom ROM (after installing the ROM "Energy.RHODIUM.28244.Sense2.5.Dec.21.Christmas.Edition") it rebooted but got a grey screen, tried installing the same ROM couple of times and hard rebooted couple of time but no success. I then installed a ROM "Energy.RHODIUM.23138.Sense2.5.Sep.13" which worked.
1. My question is how to find which compatible custom ROM's?
2. After the HardSPl the current SPL 0.85 olinex, but i have read some threads where the current version is 1.00 olinex. Do i have to install this SPL on the phone? or the current 0.85 will work? are the latest custom ROM's available need a specific SPL version?
vuday_raj said:
Thanks for the suggestion, it worked like a dream but when i tried to install the custom ROM (after installing the ROM "Energy.RHODIUM.28244.Sense2.5.Dec.21.Christmas.Edition") it rebooted but got a grey screen, tried installing the same ROM couple of times and hard rebooted couple of time but no success. I then installed a ROM "Energy.RHODIUM.23138.Sense2.5.Sep.13" which worked.
1. My question is how to find which compatible custom ROM's?
2. After the HardSPl the current SPL 0.85 olinex, but i have read some threads where the current version is 1.00 olinex. Do i have to install this SPL on the phone? or the current 0.85 will work? are the latest custom ROM's available need a specific SPL version?
Click to expand...
Click to collapse
1) GSM roms will work, CDMA ones won't.
2) no, 1.00 is the CDMA one. 0.85 is GSM one.
(Q) Cannot HardSPL T-mobile HTC Touch pro2
Guys I need help here am using window 7 home premium, I have windo
Mobile - T-Mobile HTC Touch Pro2
OS - Win 6.5 (T-Mobile ROM)
RHOD210 32M MI-BC
SPL-0.87.0000
PC Details - win 7 with WMDC
But keep getting an error message that server appears to be down...can anyone tell me how to get pass this server problem ?
kollins said:
Guys I need help here am using window 7 home premium, I have windo
Mobile - T-Mobile HTC Touch Pro2
OS - Win 6.5 (T-Mobile ROM)
RHOD210 32M MI-BC
SPL-0.87.0000
PC Details - win 7 with WMDC
But keep getting an error message that server appears to be down...can anyone tell me how to get pass this server problem ?
Click to expand...
Click to collapse
Try to disable your anti-virus, see if that works
x12CHRIS18x said:
Try to disable your anti-virus, see if that works
Click to expand...
Click to collapse
I did disable the antivirus but I keep getting the same error message..
kollins said:
I did disable the antivirus but I keep getting the same error message..
Click to expand...
Click to collapse
download this.....http://forum.xda-developers.com/showthread.php?t=578660... then try it again