So, I used JumpSPL1.56-KAIS (because I was getting the white screen of death with HardSPL) prior to installing Dutty's WM6.1 and it worked great. Now, I'm trying to use it again to install a radio (1.58.26.20) and I get this error message on my Tilt:
"The file 'JumpSPL1.56-KAIS' cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file."
I've tried to remove, redownload, retransfer, and reinstall the file, but keep getting the same error.
Has anyone had this problem and/or know what I'm doing wrong?
Thanks...
You must hard reset your device and then try again.
OK, I did a hard reset and tried again. This time it worked, but stopped at 99%. I recovered the connection and tried again. It stopped at 0%. I recovered again, but couldn't get out of the loop to try something else, so I soft resetted.
Now, I have the tri-color screen with the following
RUUNBH
KAIS1*0
SPL-1.56.000
CPLD-8
From reading some posts, it sounds like I'm stuck in the ROM update mode and I need to use MTTY to get back to the last known good state, but I'm not sure how to set up MTTY. When I try to run it with the port set to USB and everything else at it's defaulted settings, I get "USB port can not open."
I'm trying to do everything right based on what I've read on these forums, but can't seem to get on the right path. Any help is much appreciated.
- Uncheck "Allow USB Connections" in Activesync.
- Connect with MTTY
- Enter "boot"
- In case it again ends up in bootloader enter "boot" again
- If it boots in windows mobile flash "HardSPL" and nothing else !! (after running JumpSPL)
- If it doesn't boot in windows mobile, find the original rom and flash it (w/o JumpSPL)
How do I get MTTY to connect? It says "USB port can not open" when I try to connect. Do I need to change any of the default settings in MTTY?
afgoody said:
How do I get MTTY to connect? It says "USB port can not open" when I try to connect. Do I need to change any of the default settings in MTTY?
Click to expand...
Click to collapse
Uncheck "allow usb connections" in activesync (if that is what you use ..). Then put the phone in bootloader mode (tri-color display) and connect usb cable. Then start MTTY and enter boot.
Don't for get jock, you also need to select the RTS/CTS connection type!!
If you would like some one to walk you thru it, PM me. I can help thru MSN IM with file share. I've gotten good at this lately.
Thanks in a big way to Jocky of coure
jockyw2001,
Thank you so much for your patience. I am on a Windows Vista PC with Windows Mobile Device Center and have unchecked the "Allow USB Connections."
I think that a screen shot of how MTTY 1.42 pops up on my screen would help to explain my lack of knowledge with setting this program up correctly.
The Port dropdown has no USB selection available (only Com 1,2,3 & 7). How can I get MTTY to connect through USB?
Thank you
Sorry, I'm staying far from Windows Vista.
This guide will explain how to change your drivers to the xp.
GSLEON3: good work mate
Related
Hi All,
Out of the blue my HTC Vox stopped booting. I mean, it would load to the windows mobile screen and then stay there till eternity. Removing my memory card and SIM also did not help! I then tried the hard reset option.
Even after hard reset it sometimes boots(1 out of 15 times) and when it does...it hangs after 10 to 12 minutes. Still have not put my sim n memory card into the phone.
I tries flashing the ROM using the ARA 1.27 ROM. After it rebooted to the bootloader, the flash utility gave a connection error! It did not connect to ActiveSync and stayed at the bootloader screen.
I still do not know how to flash it successfully.
If anybody can help me out, I'll be extremely grateful!
Thanks
Prateek
take the battery out, put it back.
connect your Vox (USB).
Hold the camera button and turn on your Vox.
you should see a red, blue and green screen (if my memory works as it should) and the computer should recognize the device, though you won't be able to explore it with activesync.
Run the SDA_ApplicationUnlock thingy (if you need to)
now try flashing the device.
If it flashes but after 3% restart, you need to do a CID unlock right before flashing.
hope that helps.
Invalid Vendor ID
Hi MoRkusReX,
Its giving me Invalid Vendor ID. How do I CID unlock it?
Thanks,
Prateek
http://forum.xda-developers.com/showthread.php?t=330909
first post , download the last file:
Vox USPL- CID BYPASS.zip
There a Readme file in there, you should read it.
post back where you're done.
No Luck!
Hi MoRkusReX,
Since my phone is not booting into the OS thus I cannot use the UPSL_CID provided in the link.
Only once I have been able to boot into my OS and followed the instructions given in the link. The phone comes to the Linux black screen and then switchers off. Then the ROM Update Utility with which i'm trying to update the ROM gives an error that "cannot connect to the phone".
So, now I need to flash my ROM from the bootloader itself. Have managed to get mtty and connect to the phone. But even trying ResetDevice command, the phone does not boot.
Can you tell me the exact steps to flash a new ROM from the bootloader itself including CID unlocking? Can it be done??
Thanks,
Prateek
prateekswarup said:
Hi MoRkusReX,
Since my phone is not booting into the OS thus I cannot use the UPSL_CID provided in the link.
...
including CID unlocking? Can it be done??
Thanks,
Prateek
Click to expand...
Click to collapse
yes it can be done.
you don't need to boot to OS, I couldn't either. after the steps from my first post here, run the uspl_116_jockyw.bat file. follow instructions.
that will unlock the CID.
Now the VOXs' screen should be white or so... then you run the ROM update thingy.
Hi..
I connected with the usb and got the bootloader screen.
tried running the SDA unlock program...the button to unlock the phone is grayed out. Cant click on it.
Next tried running uspl_116_jockyw.bat file
..cannot connect to phone and hence copy of haret.exe did not occur and neither did pmemtest run successfully...
What am I doing wrong??
ok..
first steps again..
battery out, back in.
connect USB
CAMERA button + Turn on.
now.. does windows do that USB sound? you know.. "tu du" ?
No sound....using win 2k Nt server edition...
but has detected my phone once on that USB and then allows me to talk to the phone using mtty....as in commands like ResetDevice work on the phone using mtty..
also, cannot get into bootlaoder mode with USB plugged in...
Steps and their results:
Disabled USB connections in activesync
Booted to the bootloader (red and green and Blue screen)
Connected the USB
"USB" displays on the left hand side corner
Now tried unlocking using Apllication unlock...grayed out button...
Tried running USPL bat but stops and says phone not connected when copying haret.exe
Using windows NT server 2003
if the SDA Application unlock button is grayed, of course the USPL won't work.
why "Disabled USB connections in activesync"?
And.. I doubt this is the problem but you should check on an winXP pc, I did it on XP.
No Luck!
Tried the same with USB enabled...same result
basically the thing we need to figure out is why your computer doesn't recognize the device.
the rest is obvious.
when I go to bootloader on my device windows pops up with a message says windows found device "and it's ready to use". like when you cannot every other USB item.
have you tried doing that on an XP system?
Going to do that now....lets hope it works....
Does ur activesync turn green when u connect at bootloader?
Also, I have removed my sim and memory card...thats okay right?
yeah, I removed both of them.
and no, activesync didn't turn green, but Windows recognized the device when I turned it on. turn on the speakers and wait for that winxp "USB connected" sound.
Still No Luck!
Tried doing the same on win xp...
no luck...
it connects to win xp ans says new device found...and ur USB device is now
ready to use...
after that i try application unlock it still gives me grayed out button....
ne suggestions???
Finally....
Finally got it done...
Thanks for all the help....
I managed to cold boot into the system for one time ans then SDA unlocked it and then ran UPSL .... it ran and then balnked out...
then i disconnected the usb before the ROM update utility and unchecked the USB option in active sync...
then i flashed it with the ARA rom...
Seems to be working okay now..will test for a day and see...
thanks a lot
prateek
prateekswarup said:
Finally got it done...
then i disconnected the usb before the ROM update utility and unchecked the USB option in active sync...
prateek
Click to expand...
Click to collapse
I'm not sure this step was necessary but as long as it worked.. good times.
btw, how did you boot into the system?
kept trying hard reset and repeated booting...( it was booting 1 in 15 times type...)..and one lucky time it didnt hang..so used that window to slip in the SDA unlock and USPL..
thanks ...
you're welcome.
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
thimiost said:
I have flashed dutty's v4 rom and i want to change it
the problem is that when i try to do so i run
KaiserCustomRUU
my device goes into the 4 stripes screen it says usb
but then the program in the pc says error 260 and doesn't load the new rom
my phone still works as dutty's rom is still in but what can i do to change it?
Thank you and i have searched a lot but could not find a solution
Click to expand...
Click to collapse
OK lets start at the basics...... In bootloader mode (tricolour screen) what text does it say at top of the screen?
Have you DEFINITELY Sim Unlocked and CID unlocked?
it says these things
kais130 mfg
spl-10.0.Olipof
cpld-8
Ok that confirms you have the capability to flash. I have seen in the past some people have managed to flash one time only using jumpspl but then their device reverts back to original bootloader...I was one of those people
Next question then...Can you boot the phone normally and gain an activsync connection to it?
yes
i can use my phone normally
only i cannot put a new image in
Are you using Xp or vista? If using vista it may be worth trying a reboot... sometimes it goes doolally with its usb ports. If you cannot see the phone through WMDC or activsync after a reboot it is worth going to SYSTEM (on your PC) viewing non present devices through device manager,( Drop to Command prompt and type... Devmgmt.msc set DEVMGR_SHOW_NONPRESENT_DEVICES=1 ) removing the relevant phone connection and then re attaching it so that windows re detects it.
If you can get a connection via actvisync (win XP) or WMDC (vista) to your phone then all should be ok. Uncheck the activesync/ WMDC "allow USB connections" and try again.
If this still doesn't work then search around here for MTTY. That will allow you to specify the usb connection to the device...amongst other things.
thank you for your time
i have win xp and activesync works nice
the problem is when bootloader starts
When you attempt flashing, do you do it from the device already booted into windows mobile or direct from bootloader?
Which ever way you have tried it, try ther other way.
Not teaching you to suck eggs but just in case you dont know.... To get direct to bootloader hold camera button and soft reset with stylus whilst holding camera button down and the tri colour screen should appear.
With device at the bootloader screen, Can you confirm that you hear the windows "noise" when you unplug and re plug the USB cable just as you would when plugging and unplugging the device normally. This will determine if the device has connection at the bootlaoder stage.
why not just flash using the microsd card. its much easier that way
yes it has connection
the thing is that i have already flashed as i told before with dutty's v4
now i can't
Usually Error 260's are related to the USB port functionality ( Port can't be opened etc).
The SD card method or MTTY should sort you out.
thx again
hope it works
at least the sd trick worked!!!!
now running on winmob 6.1
Glad to hear you sorted it.
almost
i cannot use my sd card cause i have to have it formated in order to put a new rom in
thimiost said:
i cannot use my sd card cause i have to have it formated in order to put a new rom in
Click to expand...
Click to collapse
disable USB connections in ActiveSync and flash.
This Link gives a list of eror codes for Hermes, and probably the same for Kaiser.
It's likely that you have a USB port error - maybe try changing the USB port you use or a different sync cable - or just stick to SD card flashing in the future - I keep an old 1gig card for this.
this IS the problem...i cannot flash...
it stays in the bootloader with the message i wrote
thimiost said:
it stays in the bootloader with the message i wrote
Click to expand...
Click to collapse
It happen to me before hardspl again fix it, not sure why
you mean use the sd method to do hardspl again?
OHHH lord dutty we need your new rom
Hello all. I have followed the instructions to get wm6 and got stuck on step 9 of Karhoe's guide. Activesync will no longer see my device. so i cannot move forward. my phone is stuck on bootloader screen. After 'resetting device' in terapro. i saw the splash screen on my device then it went immediately to the bootloader color bars. everything else showed exactly what was on Karhoe pics. i just need activesync to see my device so i can proceed. any suggestions please. Thank you very much.
Activesyn will not see your device as it has been wiped clean of windows. Since you will need to be in booloader screen to install wm6, it doesn't matter if your activesyn sees your phone or not.
I ran into the same issue, i had to actually disable the 'allow usb...' option in activesyn so the romupdater utility can see the phone. So try it both ways.
enable it as suggested and just run the next step of installing the wm6gsmupdate...if you get some message saying connection error, then disable it and try again.
no activesync. Error [264]: Connection
thanks for the reply flashhsalf. it has not worked out for me tho. i tried both ways several times. enable/disable usb. i get same ERROR [264]: Connection.
im going to try it with a different laptop.thanks again.
Once I have this error too. Just reboot my PC and format BINFS one more time and all became fine. Don't know that is the reason, but this trick was helpfull
Have You re-enabled "Allow USB connection" @ connection options in Your Activesync??
got it to work...!!!
thanks all. i tried what was suggested all day...then when i went home i tried again with no success. to the point where my battery just died. i thought it was a paper weight at that point. but i decided to plug into the charger and the bootloader came up again. this time without the USB indication in the lower left corner. after a 2hr charge i took it to the same laptop which i rebooted. enabled usb then it worked! strange but glad i got it to work. Thanks again folks!
i updated to 6.1 but im experiencing issues with internet. ERROR
the remote party has ended this connection. this is the case with MMS as well. anyone experience this?
xdabe said:
Hello all. I have followed the instructions to get wm6 and got stuck on step 9 of Karhoe's guide. Activesync will no longer see my device. so i cannot move forward. my phone is stuck on bootloader screen. After 'resetting device' in terapro. i saw the splash screen on my device then it went immediately to the bootloader color bars. everything else showed exactly what was on Karhoe pics. i just need activesync to see my device so i can proceed. any suggestions please. Thank you very much.
Click to expand...
Click to collapse
i am also stuck to the same point ..
please help me what to do , why does this happens ..
i am very nervous ...as i cant make it a paperweight...
please help ..
thanks
my device is IMATE SP5M
and i have correctly done steps upto 8...
and when i try to do step 9 i only get three color boot loader screen
my device is super CID
info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
***** user area size = 0x7820000 Bytes
HTCSSuperCID ' HTCE
Xdabe if you actualise Radio ROM, before upgrading to WM6.1 you wouldn't notice that problem with an Internet.
Try upgrading Radio ROM for your device.
Gsmsikar once you are in bootloader, and have SuperCID, just start installing Radio ROM first, then OS.
Help please. I upgraded my Uni to one of TML's upgrades. When i reset it, screen comes up with radio version, software version, etc. but thats it. nothing happens. I have reset it several times, even taken battery out for a day and reset it again but no luck. I have also installed a new ROM but still the same. Computer still recognises the device in bootloader mode. Please help
Format the DOC with Mtty then reflash the rom
first of all, you need to be running windows Xp
then on activesync disable "allow usb connections"
plug your uni in bootloader mode into your computer, and if it is recognized open mtty and select from the top corner USB
then type in "set 14 0"
enter
type in "task 28 55aa"
and wait.
after that open activesynce and "allow usb connection"
and flash a rom into the universal
OOPs i got the link now. trying...
My Dear Samaritans,
IMPORTANT:
- My SD/Memory card is removed
- My Sim card is removed
I was upgrading to Tomal v8.9 on a vista 64 system via a virtual machine XP SP2. Update failed and I got stuck in bootloader.
Tried reflashing but got an error and the flash failed... also the program crashed during recovery.
Tried using v8.71 still crashed without any luck.
Moved to a pure XP SP3 desktop...
When I connect the device to the computer(s) "Serial" changes to "USB" but XP sees it as an unrecognized device.
Tried flashing again but same error as on the virtual machine.
Tried mtty (1.16 & 1.42) but neither give me the option of USB, only COM1 and COM2. And had already de-activated the USB connection in Activesync.
Have read through the forum but have had no luck. Everyone's issue is resolved as soon as they remove their SD or SIM, but I have neither and am also using XP with activesync's USB disabled.
Tried UNI_ExitBootloader but that does not find/recognise the device either.
If it helps -- My device is/was an O2 XDA Exec (Stock) which I had previously flashed with Tomal's v8.5
I am ready to try anything, please help!
P.S: The error is Error 112
Did you install ActiveSync on xp pc?
If not, do it now and try again.
I had similar problem. Had corrupted DOC sector
and MTTY was the only solution, but although the Serial changed to USB, I got 'unrecognised' message and Mtty didn't give USB as an option. At some point it occured to me that it was my computer's USB port, for some reason the device was recognised by 1 in 4 ports only, So I just tried my USB cable in different ports until the 'device unrecognised' messaged stopped appearing. Finally, after I was ready to cry in frustration, it just worked. Don't give up.
I heard it mentioned somewhere that the device that went through Mtty will be recognised only by the port used in Mtty procedure.
That... or your device's USB is no longer properly attached to the mainboard.
tomal said:
Did you install ActiveSync on xp pc?
If not, do it now and try again.
Click to expand...
Click to collapse
Already have activesync 4.5 installed with USB connection disabled...
Thank you so much for the prompt response and helpful thought!
enigma1nz said:
and MTTY was the only solution, but although the Serial changed to USB, I got 'unrecognised' message and Mtty didn't give USB as an option. At some point it occured to me that it was my computer's USB port, for some reason the device was recognised by 1 in 4 ports only, So I just tried my USB cable in different ports until the 'device unrecognised' messaged stopped appearing. Finally, after I was ready to cry in frustration, it just worked. Don't give up.
I heard it mentioned somewhere that the device that went through Mtty will be recognised only by the port used in Mtty procedure.
That... or your device's USB is no longer properly attached to the mainboard.
Click to expand...
Click to collapse
Thank you for the ray of hope! Will keep trying every hourly reboot in every USB port (4 in all).
Weird thing is I never had to go through mtty before so this is my first need for it.
Got the physical connection checked and it is supposedly OK...
Thank you for the prompt help...
Don't worry
I had exactly the same problem. First I tried this and it worked but still no connection via mtty. On that evening I disconnected and connected a lot and I removed the battery for a long time (one night). Later I could connect but I don't know why. Maybe these two things were the solution. Mtty showed "usb>" and I've done a DOC format...
If nothing works I would create a rom-image (on sunday or monday) for your sd-card like it's written in the service manual.
blingin said:
Thank you for the ray of hope! Will keep trying every hourly reboot in every USB port (4 in all).
Weird thing is I never had to go through mtty before so this is my first need for it.
Got the physical connection checked and it is supposedly OK...
Thank you for the prompt help...
Click to expand...
Click to collapse
No need for hourly reboots, just get into Bootloader, connect USB to your device and try different ports on computer with a few seconds in between to ensure no 'unrecognised device' message popping up. Once you'll get a connection - go for Mtty facility, the USB is the last on the list of ports.
330e said:
I had exactly the same problem. First I tried this and it worked but still no connection via mtty. On that evening I disconnected and connected a lot and I removed the battery for a long time (one night). Later I could connect but I don't know why. Maybe these two things were the solution. Mtty showed "usb>" and I've done a DOC format...
If nothing works I would create a rom-image (on sunday or monday) for your sd-card like it's written in the service manual.
Click to expand...
Click to collapse
There was no SD card when I began the initial flash but it still got stuck. Been trying without the SD and SIM but to no avail...
Thank you for the manual, downloading it now, will keep everyone posted in case anyone else is suffering from the same thing...
enigma1nz said:
No need for hourly reboots, just get into Bootloader, connect USB to your device and try different ports on computer with a few seconds in between to ensure no 'unrecognised device' message popping up. Once you'll get a connection - go for Mtty facility, the USB is the last on the list of ports.
Click to expand...
Click to collapse
Still trying, will keep you posted and thank you for the responses!
I think you understood me wrong. When your device is still unusable, I would create the files you need to do the steps in point 8.3 (Use Pre-loaded SD card to Re-flash Unit) in the service manual.
Sorry for my bad english
330e said:
I think you understood me wrong. When your device is still unusable, I would create the files you need to do the steps in point 8.3 (Use Pre-loaded SD card to Re-flash Unit) in the service manual.
Sorry for my bad english
Click to expand...
Click to collapse
It's the thought that counts not the language, thank you so much for your help!
I created succesfully a pre-loaded sd card, flashing via this sd works. But I can't copy the files. When I want to open the drive it says, that I have to format the sd card. Is there a special tool to copy the files? Or you find someone near you with a universal.
your need to format your SD after flashing.
330e said:
I created succesfully a pre-loaded sd card, flashing via this sd works. But I can't copy the files. When I want to open the drive it says, that I have to format the sd card. Is there a special tool to copy the files? Or you find someone near you with a universal.
Click to expand...
Click to collapse
tomal said:
your need to format your SD after flashing.
Click to expand...
Click to collapse
Tried the SD image method with a 128MB SD but didn't work. Maybe because I have a G4 and the method is for G3
managed to get a connection finally and ran MTTY, after "task28 55a" it just hung for a long time so I disconnected.
Tried running UNI_ExitBootloader.exe and now can get in and out of Bootloader but still cannot flash or connect...
Any suggestions welcome...
Try this....
This might sound silly but it's worked for me in the past.
1. Go into bootloader (without mem card or sim)
2. Plug-in the USB cable
3. Hold the buttons to go into bootloader again whilst plugged in.
4. DOC Format
5. Flash ROM
My Universal had loads of problems but that is how i fixed it, tried everything else like you, when i first plugged it in on the bootloader nothing happened until i pressed and held the buttons whilst it was plugged in, then windows made the usb connected sound so i quickly mtty'd! lol
Hope this helps, Good luck!!!
martinbrettphilo said:
This might sound silly but it's worked for me in the past.
1. Go into bootloader (without mem card or sim)
2. Plug-in the USB cable
3. Hold the buttons to go into bootloader again whilst plugged in.
4. DOC Format
5. Flash ROM
My Universal had loads of problems but that is how i fixed it, tried everything else like you, when i first plugged it in on the bootloader nothing happened until i pressed and held the buttons whilst it was plugged in, then windows made the usb connected sound so i quickly mtty'd! lol
Hope this helps, Good luck!!!
Click to expand...
Click to collapse
Thank you...
Xda2 stuck in bootloader screen after failed flash in vista
blingin said:
My Dear Samaritans,
Tried reflashing but got an error and the flash failed... also the program crashed during recovery.
When I connect the device to the computer(s) "Serial" changes to "USB" stuck within the bootloader screen
Tried mtty (1.16 & 1.42) but neither give me the option of USB, only COM1 and COM2. And had already de-activated the USB connection in Activesync.
Have read through the forum but have had no luck.
I am ready to try anything, please help!
P.S: The error is Error 112
Click to expand...
Click to collapse
Hi i have had similar problems also i have an XDA 2 pda originaly had wm2003 on it (tried to flash it to wm2003se ) can someone help me also im realy at a loss =C many thanks in advance (i will give more detail if someone actualy) replys to me
Wrong forum
Welcome to the forum
Universal does not means all devices, actually is a model
Please enter into the right section of the forum
Goos luck,
Can you Help?
I have an XDA II was on O2 uk network. I used to flash it all the time and knew my way around. however recently i flashed it in vista without thinking.. and as i upgraded the rom from wm2003 to wm2003se about 25% of the way through vista disconnected the device then it was unrecognised usb.. then vista started installing new drivers that recognised the device... however this then crashed flashing the rom onto the pda..
It wont soft or hard reset, i took the battery out for 24 hours and tried again and nothing.. the only thing on screen is that it says serial on the top of the screen (which changes to usb when connected but get error 101 when trying to reflash/ no activesync connection and am confused my mtty as when it does connect i cant type into the text area only paste)
on the bottom of the screen is v1.06 (which before the flash crash was V1.0 something lower than v1.06)
basicaly is the device recoverable as long as i have this serial / usb recognition by the device????? (using mtty i cant connect through ports or usb but thats because i dont seem to understand how to use it)
the other question is is there any other way to get a rom back onto the device without mtty or activesynch..
I pray that ysomeone will respond .. i miss my pda dearly
a thousand thanks in advance