Related
After having my MDA slip through my hands too often I finaly tarted looking for a solution. The thing is as slippery as an eel.
I ended up taking a simple pieces of transparent tape and sticking them along both sides of the MDA about the length of the display. You can cut the tape once its in place with a sharp razor blade. When its done well, you won't be able to see the tape once its fixed. I used TESA, but I'm sure it doesn't matter what kind as long as it is really transparent. Wouldn't try Scothtape though, as its also quite slippery.
Best thing now: I can finally get the gripp of my MDA! On the next one I'll do this right away and avoid the scrathes mine now has from falling on the floor.
I recently bough the extended battery pack (HTC BP E270) and I am satisfied with the new look and feel of the phone, not to mention the improved up time. One very disappointing thing however, is that the new back cover comes off very easily. Simply pulling the phone out of my pocket makes the cover fall off.
The cover is not broken in any way.
Is there a way to make the cover fit tighter so that it doesn't accidentally fall off.
Put glue under it or something I got the same problem as you, backcover to my 1800 mAh is very plastic and the bottom is not fully pressed onto the phone or what should I say.
Thanks Artie. I would however, like to be able to change the cover for the slimmer one at certain occasions. How do you remove the cover if you glued it onto the phone?
Gripenstedt said:
Thanks Artie. I would however, like to be able to change the cover for the slimmer one at certain occasions. How do you remove the cover if you glued it onto the phone?
Click to expand...
Click to collapse
I use double sided tape.
actually, some ordinary transparent tape might be enough to do the trick.
i don't have an extended battery myself so i don't know why exactly it doesn't fit properly, but maybe you can tighten the hold a little at some places by putting some tape on your phone near where the cover holds onto your phone.
Back Cover
blue tac my friends just a small bit in hte right place
Back Cover
blue tac my friends just a small bit in the right place
I have the same original HTC extended battery, It fits right but comes off very easy.
What is blue tac? And where to apply it?
i have the same problem...i think that double sided tape is the best way to resolve this problem...i'll try
p.brazauskas said:
What is blue tac? And where to apply it?
Click to expand...
Click to collapse
http://cgi.ebay.co.uk/Bostic-Blue-T...y_CA?hash=item3ca579e18f&_trksid=p3286.c0.m14
...or bubble-gum, if you're stingy
(i already broke one of the corner bits because of the constant slip-off)
Updates are Bolded. Scroll down to see it.
So looking around, it is obvious that there is no such thing as a dock that fits the G2/Desire Z equipped with an Otterbox. I have heard of a material called Friendly Plastic which is very malleable when prepped but when it hardens, it becomes a very strong plastic. I'm thinking of creating a custom cradle that will fit the Desire Z with the otterbox which will include a charger as well. So I'm going to be buying the material from Amazon and see if I can mold the plastic into a dock that custom fits my phone with the otterbox on.
I'll give updates as I work on this project. It might take a month or two since I am doing my Master's degree, an internship and also working on a film for school (we go into production this week [in fact equipment check out is tommorrow and we shoot thursday]). I'll try to get this thread updated as I work on it so stay tuned.
03/01/11
Ordered parts to create a custom dock. I looked around for Friendly Plastic which is extremely hard to find in California (specifically in the LA area). I found on amazon.com a similar item called Instamorph which I checked their website. It is extremely well planned and pretty much the same item but much cheaper.
http://www.instamorph.com/
Now if you delve into their site, they show you how to do it and towards the bottom of the page, there is also a "techniques" page where you can do some pretty cool stuff with the material at an advanced level:
http://www.instamorph.com/instructions/
They sell specifically via Amazon. If you spend over 25 bucks in on amazon, you might be able to get the super saver shipping, so if you plan any shopping, add this along for free shipping.
another item I bought is a Left Angle Micro USB Extender.
Now this guy is extremely rare and pretty expensive if you get it custom made.
I found a site called www.usbfirewire.com which sells various types of usb and firewire cables for an ok price. I'm saying that it is ok because it is a very unique type of cable that I am looking for therefor it seems to work best for me. This is the one I got:
http://www.usbfirewire.com/Parts/rr-mcbl-ext-xxg.html
2 things to note here: a custom made cable would cost $50, but the one I got cost me a little under 13 bucks.
Another note is that I got the 5inch length cable because I don't want to spend too much time trying to fit 3 feet of cable inside a dock of malleable plastic. I plan on utilizing as little space as humanly possible to give it the cleanest look.
Currently I have spent: $22.45 + $16.45 = $38.90
This seems like alot but it's because again, it is custom.
Once I get it, I will give more updates.
03/04/11
I just received the stuff, both of them. So I can say that they shipped really fast. I'm going to start making a test trial run of the Instamorph pellets and get used to it before I make the actual dock.
This is the Instamorph and what the pellets look like:
The 5 Inch Micro USB Extender:
2 hours later:
Lessons Learned:
1) 150 degrees Fahrenheit is a very low heat level. On my electric stove, it was around a 3 or 3.5 out of 10.
2) Do NOT, I repeat, do NOT have any of the Instamorph beads touch ANYTHING PLASTIC (this includes the otterbox, plastic cutting sheets, saran wrap, anything that you even think might be plastic). Instamorph can and will stick itself to any plastic material especially when it's closer to the 140-150 degree temperature. It is much safer when it's much much cooler. (you can find this out by touch. if it starts to resist molding, then it is probably safe to attempt an imprint, but you should test it with the smooth side of your otterbox. It will take several tries)
This is what happens when you get impatient:
3) Find a surface that is smooth (glazed surface is good).
4) Use metal equipment. Instamorph will NOT stick to metals, so using any material such as a metal spatula or a metal ruler to get hard edges. if you have a good non plastic cutting surface, you can use a knife or blade to cut it for corners and use your fingers to give it an edge.
5) find a curved edge (again non plastic) that you can mold the initial part of the plastic to get a rough shape.
6) You will constantly place the plastic back into the pot to make it soft again if you're doing alot of changes and shaping. You get on average 2 minutes of molding until it gets too hard to mess with.
1 hour later (dinner):
Ok, now that I am back from dinner:
Today I focused on creating the rough shape of the dock. I'm starting from the part that cradles the phone.
First of all, I set my stove on low. I am at 140 degrees Fahrenheit. When you boil the pellets, this is when you pull it out:
Use tongs or something to take out the mass. If you think you're a badass and want to do it with your bare hands, you are most certainly welcome to do so. Here's another look of it when it's pulled out:
I then use the backing piece as a reference. I treated this mass like play-do. I rolled it and then spread it out on the counter surface. Here I force it into a larger mass that is about 3/4 cm thick.
I waited for the mass to cool down to a semiwhite color before I take a spatula to press down on the edges to get a flat boundary. This is what it looks like when it cools down completely:
Note that you see a notch on the bottom right. This is because when you open up the silicone port for the micro USB, it is a small flap. I use this as a reference piece so that I can create a gap for the flap to slide in so it goes straight into the slot without damaging anything.
The next part is to create the side guides to help you glide the phone in when you lock it down.The first part that I worked on is the right side of the cradle which is the bottom part of the phone. Here i created a long rectangle piece. I then use the edge of my kitchen counter (which is rounded, almost circular) to create a preliminary curve. I then measured the general area of it to how high it would guide the phone.
Originally I was planning to have it go all the way up to the end of the phone but I decided it was a bad idea and cut the side down to about halfway to allow me to grab it from the top half.
Now I worked on the left side (top of the phone). Here I noticed that there is a silicone cover for the headphones, so I decided to have the guide as tall as where the silicone port is at.
Now that I have done all that, This is all extremely rough work. Once I assemble the pieces that does not have the Micro USB port, I'll be sanding them down and smoothing it out so it looks better. Here's the general look of how it will be fitted in for now.
First of all this is only the part that the back of the phone will be sliding down. I am planning to create the bottom part that will house the Micro USB cable and the back piece that will hold the backing upright as the back base.
END OF DAY 1.
I will update on a later time. I am on set from 5:30am to 5:30pm so I might have time to work on the next step, but right now I might update this thread next week depending on how much time I have. I am currently juggling an internship, class, film production, post production, and moving to a new apartment (has to be done by the end of this month) so I might not update for a while. Hopefully I can work on it soon.
Small Update: 04/05/11:
After having an extremely hard time molding the material with a spatula and the kitchen counter, I finally caved in and bought a set of clay sculpting tool. (Link: http://www.amazon.com/gp/product/B000SVRSRY ). I'm waiting for it to come in the mail.
Another update to this is that I switched my method for creating the dock. I decided to start from the bottom first. I created the base for the dock by creating the first layer, this is where the general layout of where the microUSB cable will be laying on. Then I worked on creating smaller pieces that fit around the first base that sculpts itself around the cable. I'll be posting some pictures sometime later when I have more time.
April 26 2011:
I should've updated this a long time ago, but my internship has finally come to an end so I had enough time to give an update.
First thing I did was make use of the tool set that I received via Amazon from the above mentioned link:
Now with the use of these tools, I start to put the dock in parts and layers.
The first thing I did was create parts of the first layer, combined them into one piece, then finally heat them in the water pot just long enough to get a small amount of the whole surface moldable without damaging the core structure.
From that I create the next layer which is the top layer:
note here that the top piece (with the weird looking hole in it is made to accommodate the silicone flap that covers the port that comes with the otterbox case.
the last piece hasn't been change too much because I'm still trying to decide if I should have a backing piece for the phone or have a "well" that holds the phone just from the bottom.
the layers will be secured through 4 small metal bolts (the ones that you get from Ikea furniture that feature adjustable shelves [the small metal bolt thingies that you can remove and adjust.])
Another thing to note with this is that when using the pottery tools, you can easily dip the tips in the hot water for 5-10 seconds to heat it up and allow custom targeted molding at parts you specifically want.
Here are some more pics of the parts as I molded them.
5/27/11
So for the past few days I've been tweaking with the design and finding methods to give it a more defined look. While I was at Ikea, I came across these handle pieces that were meant for a particular furniture. They had 90degree angles, metal, straight. So I bought that and use it as a partial mold when I shaped the edges. After working about 6 hours over the course of 2 days, I have come pretty close to what I want before I finish it with sanding and a way to put it together.
Here are the pics of what I have ended up with so far. I still need to sand it, and also figure out a way to combine the pieces without encasing the cable permanently.
Here are the two pieces separated:
This is the bottom piece on where the connector pointed upwards
This is the bottom with the cable in it
This is what the pieces will look when put together (assuming that I can find out a way to combine them together [non permanently])
This is the dock with my phone in it (notice the rubber bands. It's only a temporary measure to keep it together). And It's charging! that means the connection is secure!
This is the side view from the right side
This is the side view from the left side
top view of the dock
From this point, I'd like to ask your help and suggestions as to how I can put the two pieces together to so that if anything happens, I can open it up and replace the cable again. I'm also considering the opportunity if in the far future when I happen to replace my Desire Z I can always remold the piece without doing extensive damage to the cable if it happens to survive.
My next steps are as follows:
Add a piece in the back to support the weight of the phone.
Sand and prep the surface to make it smooth.
Create a method to hold the 2 pieces together
potentially spray paint it to a specific color
Any suggestions would be great since this is my first ever project that is building a custom material.
Thanks!
5/29/11 - 99.90% completed!!!!!
After spending roughly 6 hours on it, I have managed to finish the dock!!!
The first thing I did was to drill 5 holes into the dock to place the metal pin. I started by drilling with a 1/16 drill bit as a guide. and finally followed up with a 3/16 drill bit. I drilled from the bottom piece with the 2 pieces together but stopped part of the way through the top piece because it was unnecessary to drill all the way through. This is for the metal pins to place in between the pieces.
After that I worked on just the top piece and drilled just deep enough for the pin to fit in flush.
Went back to the bottom piece to cover up the holes by using the plastic pieces that got pulled up as I drill to fill in the bottom hole and using the rounded end of one of the clay sculpting tools to jam pack it back down to the bottom to ensure a strong fit.
I then combine the 2 pieces together to see the fit. I noticed that I failed to account for the notch between the pin so I went back to the hot pot and heated up the inside surface of the bottom piece and placed the metal pins in and pushed it in so the notch sinks below the surface (with the help of a hammer [and no, don't go "HULK SMASH" on it, just tap it lightly]).
From that point, I tweaked the fit with the cable inside of it and by looking through the gap, I either added or removed plastic parts so that it finally closes completely.
After that is all done, I started with a 60 grit sand paper (with a hand sanding tool) and worked on ALL the surfaces and sanded until I got 99% of the surfaces rough
I then go back and refit the metal pins to make sure that the pieces still fit and see if I need to make tweaks (which I did since at 60grit, it takes away quite abit of plastic).
I did a little more tweaking with the plastic. Adding and removing as necessary to make it fit flush.
After all that is done, I go back and worked on all the surfaces again with a 150grit sandpaper to give it a smoother finish. and finally finished it off with a 220 grit sand paper.
A good hour and a half later of hand sanding it and sore back and arms the surface is as smooth as a 220grit sand paper can offer.
The last thing I did was reheated the hot pot to around 145 degrees Fahrenheit. I took apart the dock again and this time placed it in the hotpot for around 10 seconds. Just enough for the malleable plastic to "shrink" back into the plastic and give it a smooth finish.
After it's done, I ran the pieces through cold water to set the plastic and put the whole thing together.
Below are the pics of what I have done (again, these are thumbnails. Click on it for full size):
All the pieces completely disassembled. 5 metal pins. 2 plastic parts. Left Angle micro usb extender
Metal pins inserted into the bottom piece
Dock completely assembled
My phone on it
Plugged in!!!!
Landscape mode! (and notice that it's charging! So the cables work!)
More angles
Finally, I have one thing to ask of you guys. Should I leave the dock to look as it is or should I do something about it?
I am thinking about either spray painting it or buy a "skin" (think DecalGirl skins) and cut out the pieces to fit around it.
Tell me what you guys think and what you can think of to make it better! Thanks!
oh yeah, and I finally did something about the back piece of my otterbox when it got screwed up. I did the sandpaper treatment on it and here's what it looks like now:
Sounds interesting, looking forward to seeing your progress/results.
I'm currently in the process of ordering parts. So here's a question for everyone:
Which would be the best extension port for the dock. Standard USB, Mini USB, or Micro USB.
My plan is to mold a Micro USB male head to another adapter to give it the most commonly used female port. The idea is to plug in a cable into the dock to minimize the chance of the inner cord being damaged and moved unncessarily. (think of the docks you get off ebay that just have a male port to plug in the phone and a female port out the back end so you can plug in a cable of your choice (length, brand, etc)
Here's a poll of what your preference:
http://www.polljunkie.com/bA7AA5/Poll10601.aspx
Updated: 3/4/11
Any progress/updates?
Sent from my T-Mobile G2 using XDA App
Unfortunetly, not yet. I have to get through this month first. I need to have a first cut of my film out very soon, internship, finish moving to a new apartment and deal with classes. I will be promptly resuming this project when this month is over.
Sent from my Desire Z via XDA App
small Update. Check bolded txt in OP
Updated April 26. Bolded text in OP
Updated May 27. Bolded txt in OP
mputtr said:
From this point, I'd like to ask your help and suggestions as to how I can put the two pieces together to so that if anything happens, I can open it up and replace the cable again.
Click to expand...
Click to collapse
Why not try Moulding little tabs onto one side & then a hole on the other so it kinda snaps/slides together. That way you can always reopen it at a later date
KarlosTheJackal said:
Why not try Moulding little tabs onto one side & then a hole on the other so it kinda snaps/slides together. That way you can always reopen it at a later date
Click to expand...
Click to collapse
so you're saying to have one of the pieces have tabs that extends to the other piece and add a hole to kind of screw it in? Sounds like a good idea as well!
I'm a little fuzzy on the visual of it, is it possible for you to provide a visual example so I might be able to replicate it? Thanks!
Updated! 99.90% done!
does anyone have suggestions or comments on how I can improve on the dock?
The finished project looks awesome man! I think, like you said, if you added some type of black texture or skin to it that it would look fantastic and even store purchased. Great craftmanship.
Sent from my HTC Vision using XDA Premium App
PatrickHuey said:
The finished project looks awesome man! I think, like you said, if you added some type of black texture or skin to it that it would look fantastic and even store purchased. Great craftmanship.
Sent from my HTC Vision using XDA Premium App
Click to expand...
Click to collapse
ah, so you think a black coloring to the dock would work? I'll test that out!
I'm also thinking of maybe taking the top piece back into work and take out more of the recess/well for the phone and maybe fashion a silicone or softer piece for the phone to rest in and might look better. (that or get a sanding head bit and sand it down till it's smooth)
Would you suggest using a skin (like a sticker type material) or just spray paint the darn thing?
as usual for those who have read any of this, I would like to get suggestions on what I can do to improve upon it.
Currently I'm also researching a method on how to activate the phone's "dock" mode. As far as my research goes, some android phones have a special magnet inside of it that reacts to polarity (one polarity for car mode and the other for home dock). I also read that potentially, HTC made a special micro usb cable that has 1 additional pit that "activates" the feature. I do not really know much of this so I'm trying to figure out how to make this happen. If someone here happens to know, and it can be something I can physically manipulate, I'll modify the dock to include the manipulation.
and again, Thanks for the praise and your suggestions!
nice work and detailed instructions are always nice. I would definitely spraypaint it black. Did you form the top and bottom parts by hand? they look a litte bumpy to me.I thought about doing this for mine and integrate it into my desk.
As for the docking mode (deskclock) i use Alarm Clock Plus. It switches into dockmode when you plug it in. I think they getting the info if its docked either from the orientation of the phone and its usb connection or the poweradapter - maybe both. Maybe its the dock im using but i did't notice some special wiring oder plug.
dieterxy said:
nice work and detailed instructions are always nice. I would definitely spraypaint it black. Did you form the top and bottom parts by hand? they look a litte bumpy to me.I thought about doing this for mine and integrate it into my desk.
As for the docking mode (deskclock) i use Alarm Clock Plus. It switches into dockmode when you plug it in. I think they getting the info if its docked either from the orientation of the phone and its usb connection or the poweradapter - maybe both. Maybe its the dock im using but i did't notice some special wiring oder plug.
Click to expand...
Click to collapse
everything is formed by hand mostly. the curved parts had to be done by hand, but I did take down alot of the uneven by sanding it down for a good hour and half.
I'm currently using Alarm Clock Extreme and it does not have the dock mode, which bums me out, but I'm supplementing it with Night Clock which is a really neat app. I also paired it up with Automate It by adding a kill app on unplug action so it's sorta kinda like dock mode.
do you have any suggestions as how I can make the surfaces smoother? Is there something that I can do or get to remove the bumps more effectively?
i would use some kind of metalblocks and put the dock between them but that only works before putting it all together. Or maybe just wrap the plastic around the metalblock so that its hollow.
I probably wont be doing anything like messing with metal material since I do not have the necessary equipment nor do I have the time and money to afford that.
But I'm thinking of potentially using a skin type material and spraypaint it + my own design for it.
I had some fun with the dremel tool at my schools workshop room so I was able to get the right depth and well for the phone to slid in.
I wonder if there is anything like silicone material that can be injected on top of the material so I can make an impression (safely) and so when it sets it actually is cushioned rather than placed on the hard plastic.
I'll see if I can post more pics if I deem that the extra sanding I did made any difference.
Any updates to this?
hello, i have a couple of scrtaches on my nexus one body. is there any product that can remove them?
your help is appreciated
thanks
hnijhar said:
hello, i have a couple of scrtaches on my nexus one body. is there any product that can remove them?
your help is appreciated
thanks
Click to expand...
Click to collapse
Best bet go in to a car shop which have loads of paint, ask the guy what he thinks the best match would be, buy smallest bottle and spray sum in a tiny plastic cup, get an earbud, add a very small amount of paint on the bud from the cup, den dab on a clean area of the cup to remove 90% of paint from ear bud, so there's a extremely tiny amount on it then rub on smoothly on discolored areas.
Tip. Buy smallest bottle as very little is required.
/ Go 0.5 shade lighter/ use mixing compound once dried to blend paint very cheap 2$ can get from any car/paint shop rub on with lint free towel./do this only on front metal bit of phone as this will look stupid on plastic, ps. you can buy a plastic battery back cover from eBay for $7 from china
hit the thanks button... thanks
kuljit55 said:
Best bet go in to a car shop which have loads of paint, ask the guy what he think the best match would be, buy smallest bottle and spray sum in a tiny plastic cup, get an earbud add a very small amount of paint on the bud, from the cup den dab on a clean area of a cup to remove 90& of paint from ear bud, so there's a extremely tiny amount on it then rub on smoothly on discolored areas.
Tip. Buy smallest bottle as very little is required.
/ Go 0.5 shade lighter/ use mixing compound once dried to blend paint very cheap 2$ can get from any car/paint shop rub on with lint free towel./do this only on front metal bit of phone as this will look stupid on plastic, ps. you can buy a plastic battery back cover from eBay for $7 from china
i kindly spent 10mins of my time writing this so please hit the thanks button...
Click to expand...
Click to collapse
Have you done this? Does it end up looking OK? Do you happen to have any before or after pictures?
Thanks for the detailed instructions!
i have tried this on a slight chip of paint. it worked very well, i can show an after photo but i did not take any before. but i would only do this if you can find a very simular shade like a could. make sure u test the shade first on somthing metal to see final colour. show the shop keeper your phone and say i need this colour. s/he should have expertese on best colour available
Why don't you just change the housing is like 40 bucks My Nexus One ended up looking new. I already polish the old housing I just need cream to make it shine and I'm gonna paint the back door white and the bottom too maybe this weekend. this is the cheapest housing on ebay. http://cgi.ebay.com/Housing-battery...796?pt=LH_DefaultDomain_0&hash=item3a659866e4 32.00 bucks.
I'm actually way too much of a wuss to consider changing the housing...at least for now.
Way back when I had a Moto Razr vx3 or something and I attempted to change the housing and messed up on putting it back on and a corner of it was always loose.
Anyway, my Nexus One only has two tiny scratches just below the search hard key...not really worth it to change the entire housing. Though perhaps I could pick up a spare housing set in case something were to happen in the future.
Unfortunately, since our N1s have a kinda brushed look to them, there isn't a way to get rid of the scratches without it being more noticeable than the scratch itself.
There was someone who ended up completely polishing his N1 until it was a mirrored finish... I saw the pictures on here a few months ago.
bassmadrigal said:
Unfortunately, since our N1s have a kinda brushed look to them, there isn't a way to get rid of the scratches without it being more noticeable than the scratch itself.
There was someone who ended up completely polishing his N1 until it was a mirrored finish... I saw the pictures on here a few months ago.
Click to expand...
Click to collapse
yeah that is what made me polish the housing but I been so busy to even finish, He did a incredible job too
I just started developing this odd creaking noise near the bottom and sides of my S4G. Even with a Seidio Active case wrapped around it, the creaking can be felt and heard when hitting the bottom buttons.
The fix is pretty easy. You just need to decrease the amount of movement the back cover has.
I had some .010 mil fiber (fish) paper laying around so I cut a small square that covers the sim card and microsd card area. You can probably use something else, but hey, why not use some insulated paper if you have it.
Lay the paper on top of the area and then slowly place the back cover back on. No holes are in that area above the sim and microsd, so no worries there. You should see an immediate improvement
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
jlevy73 said:
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
Click to expand...
Click to collapse
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
GideonX said:
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
Click to expand...
Click to collapse
I took a post-it and folded it twice. Then placed it on the bottom right area and closed up the cover. For me when I press down on the bottom right side of the screen the whole screen sort of depresses a bit. Only way I could get rid of that was to place the paper in that region. Problem solved.
Post it would have been my backup method
Sent from my HTC Sensation 4G
buy another battery, i recently got an anker also had the creaking problems, noticed the anker is a TINY bit thicker than the stock battery and it removed that problem completely. and that anker battery was DIRT cheap
I just lined the case with some scotch tape. from the bottom to about 3/4 of the way up. I just went around the antenna nubs and the usb hole.
Posted this in another thread, but felt it was valuable here too...
Got the creaking here also, definitely a design flaw. Being obsessive with my devices i couldnt live with it!
I do not recommend putting paper in the cover to fill the gap, as this is just expanding the cover further making it even MORE loose when the paper is not in there. Also i wouldn't recommend it because the paper pushes the back cover out a little more, you may loose a connection for the ground. Which is the little metal springy thing, half way up the right hand side. Obviously its not a good idea to 'push' the cover further away from this ground spot. I have heard that people have had issues with screen responsiveness due to a static build up from not grounding properly.
What i did to fix this problem was a bit of a kitbash of sorts.
Mine was creaking on the bottom right area, like most. The problem is there is too much play between the little black catches on the battery cover and the latch on the handset. Instead of filling up the gap between the phone and the cover (Ala paper, card in the cover) I closed it!
What you need to do is get some very thin plastic film. Like that on kids toy packaging etc. Not the thicker stuff though. This stuff would be under 1mm thick. It came as a viewing window in the box my new wallet came in. So you can sorta imagine what im talking about.
I cut a piece about 10mm long and as wide as one of the two little black catches. I applied a VERY thin coat of super glue to one end of the film. Just enough to cover the area under the catch. Then i carefully placed the film with the superglue on it under the catch, and then quickly applied some pressure to it with some tweezers. Then i carefully cut the excess off with a pair of finely tipped nail scissors.
The result is that it now PULLS the screen/phone INTO the cover more by making the little black catch thicker. Not the opposite (paper method), which pushes the cover out, creating a further problem of adding more paper under the cover over time as the cover expands/loosens to compensate. Not to mention a possible grounding loss and resulting damage.
Hope this helps some people that have had multiple replacements or could not be bothered replacing for such a cosmetic issue. (Like me). It definitely works, just got to get your surgeon on and be accurate with your placement of the film.
Apply this to what ever side creaks the most, and bam its gone. Nice. Solid phone... again.
If anyone wants more specific details etc, im all ears.
Regards,
Matt.
will try it with an double side film ...
i mean a film that hold back cover and phone together ;-) i think doing paper in there will do damage with time
I contacted HTC and they sent me another/new one. No more creaking!
RaptorRVL said:
I contacted HTC and they sent me another/new one. No more creaking!
Click to expand...
Click to collapse
Back cover or whole phone?
I have the same problem too. And it just seems to get more and more "cracking"