My i-teq X-bond is Dead pleas hellp me - JAMin, XDA Neo, S200 Software Upgrading

Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...
Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
i am mohsen from iran tehran

Related

Updating Qtek S200 ROM has cell phone locked in Boot loader

Hi there,
I bought a Qtek S200 and I tried to do a ROM upgrade. I followed the instructions given in the website http://kimpeacocke.blogspot.com/2006/06/how-to-perform-rom-upgrade-on-your-i.html
I got the upgrade from this site at ftp://xda:[email protected]_022021_Dopod_PDAMobizEdition_v101.zip
I followed the procedure given in the website given above. After I upgraded successfully the phone has become locked in the boot loader screen. I have done both soft reset and hard reset. Nothing works. The phone gets locked in the boot loader screen. Need help.
Thanks,
Julian
Try to reflash with Qtek ROM instead...
Why you said that it's locked on the Bootloader screen?
Is it frozen or locked?
Hi Rayan,
I tried flashing with the Qtek ROM. I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there. Nothing else happens. I have sent the device back to the guy from whom I bought it.
I got the same problem as Julian - I tried to upgrade with the mentioned ROM and now my device are stucked at the boot screen :?
Some help here ? I'm in same situation
I have an O2 with Dopod rom, after I instaled some software I must to restart and then my O2 are stucked/frozen on Windows Mobile splash screen
Only if I remove the battery I can stop the pda.
I can't do nothing to make him to start. Some ideea ?
:shock:
Later Edit :
solved with http://forum.xda-developers.com/viewtopic.php?t=49298&sid=35f5c1e9e165997b4634ea0c7700ac76
Same issue here with a O2 Xda Neo with German Rom.
Applied the procedure of the prophet wiki : How to CID unlock and Upgrade your Prophet (SPL 2.09 & 2.15)
After step 6 and a soft rest it is stuck in bootloader and will not do anything else, not even off or hard reset...battey has to be removed in order to shut it off....
Any ideas?
Remind me to find the guy who wrote the wiki page on unlocking CID in Prophet......good job pal......
Aaaaarggghhhh %^*^%*^%*^%*
Problem solved..
Hi everyone,
Good news at last. I sent my Qtek S200 to the guy from whom I bought the phone. He fixed it and now I am a happy man. You can check with him if everything else fails. Email him at E gadget Depot ( [email protected]).
All the best..
i tried to upgrade my QTEK S200 with this RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip it got to 95% and then it gives me nbf file cannot work with your PDA. Please help.
I have this problem too, i know only one exit from this situation - i have flash my s200 with RUU_215737_2157135_023021_QTEK_s200_RUS ROM, now it work fine.
you find it her
bootloader issue
I have the same problem too, If anybody know method to fix this problem please help us.
I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there.
THX in advance for you help
Robert
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Please, the links to the solution does not exists anymore.
I need help!!
Qtek S200 stuck in tri-color screen, all flashing so far still does not make it work..
When doing a hard reset I get format failed.
/Jonas
I have same problem!
Anyone can help?
TJSM said:
I have same problem!
Anyone can help?
Click to expand...
Click to collapse
Go to HMA4's upgrade guide or my thread in my signature...
same problem
i have exactly same problem and i couldnt solve it too.So can someone help us?
Please someone explain completely what should we do.
i can not active sync and waiting on the bootloader screen
bacardilima said:
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Click to expand...
Click to collapse
daelee,
you can get normal state, follow the bolded attention at above quote.after entering the 3 colour screen connect USB and you can load the original WM5 ROM on your device. after that, upgrade to any wm6 by the rules and active sync.
the link is dead on that message..
i went to the that page and the link for solution is dead.
http://forum.xda-developers.com/showthread.php?t=376561
find out is there anything that can help!

PLease HELP..ROM update !!!

i have tired v3 wm6 update and..after the update my screen is stuck...at o2 sign..with bubbles,, the four red words appear on the screen but doesn't change anything...
i'd like to reflash back but it doesn't seem like connecting to PC via USB..
what do i do...?
and i found..
it just stopps in the boot loader mode and turns to black screeen .. and that's it...
I cna't even connect to USB so which means i can't flash back to normal..
is there any suggestions??
like resseting back up?
I have tried soft and hard reset but both don't seem to work.. still stuck in the bootloader mode....
What do I DO>>>>>>>>>>>>>....please help me...><
Try to Enter Bootloader:
Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
However, you have to write in the right post, i guess you mean the Ohlala_WWE_WM6_v3 ROM. If you had read the entire post youl'd know that this one is bad. V4 should solve the problem.
thanks for your answer !!but..
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
llvll said:
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
Click to expand...
Click to collapse
You cannot use "upgrade_rom.bat" to flash ur device with RGB screen. The bat file is for upgrade, not for fresh install. It means that you have to install AKU2.xx NVID.exe (executable) first. The .exe file can recognize ur device via RGB screen.
After reset ur device with AKU2.x and successfully connect to the PC vis Activesync, you then can run upgrade_rom.bat.
And... don't be too panic. You have to read more.
thank you so much !!
i' ll try it right now !! omg ...i'm so relived that I got an answer !!!
you are the best!
um...
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
llvll said:
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
Click to expand...
Click to collapse
here http://www.4shared.com/file/12240109/ca99469a/RUU_Prophet_220734_2207114_024721_NVID.html
thanks !!!
is there an o2 version of NVID??? anywhere? i've just installed this but it says Qteck..
No it's a Qteck ROM not an O², I don't know if there is a 2.20 NVID ROM from O² here, sorry.
i've just installed AKU...thing
after installing AKU...
my phone doesn't seem like it can connect to Antisync program..
is there any reason why..this is happpenin..?
make hard reset after flash firmware!
yese !!
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
you could try this. Someone else posted it here, and when my phone stopped connecting after some update it fixed activesync. It's a switch.
llvll said:
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
Click to expand...
Click to collapse
Had O2 ever released HTC Prophet?
Sorry but I'm not O2 fan.
I have only Prophet so I know only Prophet.
You could go to the right thread for ur device O2 and look for the right .exe file.
PS: is it XDA Neo? If it is Prophet it should be OK.
Try holding Camera+Comm buttons during pressing reset button ur device will ask u to Format something. Press send button (green phone button) and try again.
Safe
Thanks guys, you saved my S200
Matos
Ohyea !!
I found the solution !!! dat Qteck one worked but um....
yea and my phone is Xda Neo !!!
the black one !
thanks for all the replies guys !!!!!!!
Whoohoo, thanx for mentioning the bootloader mode (by only holding the camera button ) Now I can try another WM6 rom, which does work I hope
hello there same problem here.. mine is also xda neo.. when trying to upgrade wm6 it stuck exactly same as yours..how did u fix the problem? thanx for ur advice

My i-teq X-bond is Dead

My i-teq X-bond is Dead
--------------------------------------------------------------------------------
Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...
Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
i am mohsen from iran tehran

My i-teq X-bond is Dead pleas hellp me

Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...
Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
i am mohsen from iran tehran

No bootloader for Gene

My htc gene is bricked.I have tried all the methods. I am unable to recover using Orefkov's method. When I try to press power key or soft reset button , onlr red and green light blinks. Nothing else happens. no charging indecator when i connect it to wall charger. I am even not getting the tri color screen.
please help me. to at least get into bootloader.
plese reply
hi guys can u please help me fin solution to my problem.
pravin.kamdi said:
hi guys can u please help me fin solution to my problem.
Click to expand...
Click to collapse
U better ask in gene's forum..
so whats happening exactly .. i flashed yesterday first time ever ... but after reading many times teh first sticky step step guide for flashing..
http://forum.xda-developers.com/showthread.php?t=472169

Categories

Resources