this is a major annoyance... I've had a Samsung i760 for a couple months now and have found it seems to have a serious design flaw.
I like to listen to music at work, through my phone using a wired headset (two way headset with mic). I work in a quiet office environment. I always set my ring to silent/vibrate while at work. If I'm listening to music, and happen to receive a call, the music will stop playing through the headset and will start playing through the built in speaker of the phone for all my coworkers and supervisor to hear.
The music would continue to play like this even after answering the call... I have to bring up the player and stop it manually. I was able to partially alleviate this by disabling the 'play in background' setting. With that, the music will still play through the external speaker briefly, roughly 3 seconds, before the player pauses the song. Which is still unacceptable.
I have tried TCPMP and Windows Media and had the same result.
Also, if I have the phone set to ring audibly, the ring is forced through the speaker as well, and the music I was listening to AND the ringtone will play at the same time for those 3 or so seconds.
what I'm hoping someone can help me with is a) a way to make ringtones play through the wired headset if possible, or b) at least keep the sound from being forced through the external speaker when the wired headset is connected and I recieve a call. As it stands, I either can't listen to music at work (a big part of why I bought the phone), or I have to turn the phone receiver off and risk missing calls. Either option sucks and is making consider another phone... though I don't know if this is a WM6 issue or an issue with this specfic phone.
any help would be greatly appreciated!
*bump* anyone?
any way thru the registry to disable the built in speaker alltogether while leaving the headphones operational?
On Acer s200, you can change the value of registry key HKLM\Software\Acer\Scenario\HeadsetIn to 1...
Maybe that can help...
Related
Hi,
When I still had wm5, whenever I received a call, the bluetooth headset interrupts the music being played and plays my ringtone. However in wm6, it still interrupts my music, however the ringtone comes out of the speakers of the cellphone. Is there anyway to remedy this without the need for any expensive software?
I have a Sony Ericsson A2DP Headset. It connects fine for both calls and for listening to music. There is however one small annoying issue.
If I'm listening to music (generally I have to have the volume up quite high) and a phonecall comes in and I take the call; something weird happens when the call ends.
The bluetooth connection is dropped and basically everyone in the vicinity gets and earful of whatever music I was playing before the call. This can be pretty bad if I'm sitting at one of our quiet, open plan offices. If I press the play buttin on my headset it reconnects and audio comes in over the headset again but it's not good to have to do this after every call.
Anyone else had this issue?
Thanks in advance.
Whenever I encounter a quirky bluetooth problem, deleting the pair relationship and repairing sometimes helps.
Works fine for me... Could be headset specific, as I use Motorola S9's and Plantronics 855's without the issue you're having.
It does it for me too. After the phone call the music is played through the phone's speaker for just a couple of seconds, then gets transferred to the headset in mono for a couple of seconds before reverting back to normal.
I can see this would be annoying if you were in a quiet place.
Sony Headset
and me, funnily enough I have a Samsung MP3 player and the headset works perectly with that - good old HTC
Hi,
I searched the forum, wiki, etc., but didn't find an answer.
I have an AT&T Fuze with the stock ROM (WM 6.1). I know the Fuze is supposed to support multiple simultaneous bt connections. What I would like to do is connect A2DP to my Pioneer stereo for music playback, and also connect handsfree to my Jawbone 2 headset for phone calls while in the car.
I can successfully connect A2DP to my stereo for music by itself.
I can successfully connect HFP to my Jawbone 2 by itself.
I *have* managed to connect to both at the same time, by staying on an active phone call with my Jawbone, then telling my Fuze to connect to the car stereo. However, no music could be heard (from either Mortplayer or WMP). The phone call stayed up just fine though.
Anyone know if there's a way to get both working at the same time?
(And before you ask, I would just use the hands-free capability of my Pioneer stereo for phone calls too, but I've found my car is too noisy for anyone to hear me with the Pioneer's microphone unless I hold it right in front of my mouth, which defeats the "hands free" goal...)
Thanks for any help you can offer.
Best,
Chris
In your case I do not think that is possible since the concept of being able to juggle 2 devices at the same time requires 1 to relinquish control while the other goes active. It turns off the music so you do not get distracted while talking and reconects the music after the call is over.
It seems to be a software protocol if anything. Yes both can be connected at the same time, but both cannot be "active" as in doing both music playback and voice calls.
I have a bt headset that handles 2 profiles at once and according to the protocol, if a call comes in, it pauses my ipod and then picks up the call and then resets back to normal after the call.. Either you have to mess with the coding itself or someone has to come up with a workaround, but I do not think that is possible.
Thanks for the reply. I had hoped it might be possible for the Fuze to route stereo audio to one BT profile (A2DP), while non-stereo audio (e.g., phone call, system tones, etc.) to the HFP profile, almost as though the profiles acted as addressable "service ports" (ala HTTP, SMTP, etc.).
But, unlike with TCP/IP, I admit to knowing next to nothing about how the BT stack works and how profiles are applied to certain types of data (or, how data is routed to a given BT association based on profile).
Thanks again,
Chris
well the thing is.. the fuze can connect to multiple devices simultaneously, but based on the music and voice call order, it is prohibited from doing both at the same time. so therefore when there is no call, the music plays, but when a call comes it, the music is paused and resumed after the call is done. (obviously the call has higher priority here).
My only suggestion is to leave it as it is since it is done so that you do not get distracted while talking and probably while you're driving.
Multitasking is difficult when you're listening to 2 things, responding to 1, and driving at the same time. The more you multitask the less you are able to devote to your main activity (in your case, driving).
but yeah. if you can find someone who can mess with that and allow for both to be active at the same time, then congrats. Otherwise just think of it as a safety measure.
Except that, when I had both the headset and the stereo connected to the Fuze, the music *didn't* pause. It just didn't output (as though the volume was muted). In fact, in both Mortplayer and WMP, it appeared as though it was playing at ~2X the normal rate (just watching the track playback time counter).
I know what you're talking about re: listen to music, call comes in, music pauses, call ends, music resumes. That's the behavior I get when I use the car stereo for both handsfree and A2DP.
The behavior when connected to two different devices seemed to be different, though, so I hoped that might mean it was in fact possible.
-Chris
yeah I know what you mean, but maybe the fact that it tried to do both tripped it up and so it took the call as a higher priority and focused the data towards the call.
atleast that is what I think.
I have almost the exact same configuration, except I am using a Sony car stereo but have a jawbone. What I have to do every time I get in the car is the following.
1. Let my stereo connect to both hands free and wireless headphone services.
2. Open bluetooth settings
3. Manually connect to my Jawbone.
It works great.
ATT Fuze
Energy Rom 072209
Old jawbone
Sony XPLOD Car Stereo
I'll also add it's pretty neat to be able to push the jawbone to activate MS Voice Commander and choose what music I want to play over my car stereo.
frankrizzo said:
What I have to do every time I get in the car is the following.
1. Let my stereo connect to both hands free and wireless headphone services.
2. Open bluetooth settings
3. Manually connect to my Jawbone.
It works great.
Click to expand...
Click to collapse
Thanks for the reply. I'll give that a shot. I'm not sure that my Pioneer stereo will automatically connect both handsfree and A2DP. I know it will do handsfree automatically. We'll see...
-Chris
I've been having an issue with the media audio streaming to Bluetooth on the Blaze, which I did not have on my previous phone (Optimus). I pair with a Soundfly View in my car, and use the app BeyondPod to listed to podcasts. On a "fresh" Blaze, the audio will begin to play/stream for a split second, and then stop (though the podcast will continue to "play" or advance on the phone). I can occasionally get it to do it again by clicking play, but never for more than that split second.
Through experimenting, I noticed that phone audio seems to be fine, as well as audio on the Music player. What I've found, consistently, when this happens, if I start the Music player, start playing some audio then pause it, then go back to BeyondPod, it streams fine. At least for a time, though I've yet to figure out exactly what "resets" this workaround. But when I'm unable to play, I have to redo this Music player trick to play the podcasts.
Any clue what is going on here, and any permanent fix?
Bluetooth streaming... I have been doing this for a few years using a slightly different method that I'll share here in hopes it might help. I know this is kinda unrelated to your app, but this might be a fix.
Connect any bluetooth headset (I use my PS3 headset)
Download an app called BTmono (its free and a very simple interface, on/off)
Press the on button
Now any sound you would of heard out of your phone speaker you hear on your headset. This lets you listen to music, audio books, videos, or whatever on your headset. When you are tired of it, make sure to press the off button on BTmono to go back to normal. Hopefully this will help or at least provide a temp fix for now. My boss just thinks I like to wear mine all the time, he has no clue I am jamming dubstep and listening to audio books all night
Well, even should that work, it's really the same solution...using another app to force the streaming which should be happening automatically if you're connected with the right BT profile.
I did forget to mention that I do use A2DP volume, which launches an app (BeyondPod) and adjusts the volume when BT is connected. I also used it on my old phone, so I doubt it's related, but...
Nobody else has any problems with Bluetooth from other apps? It's just me???
Firstly, I would just like to clarify that I am not talking about the autoplay when connecting to a bluetooth device (in my case, it's my car stereo). I actually really like that feature and would like to find a solution to my issue that doesn't disable that, if possible. The problem I am having is when I receive a phone call, whether I answer it or not. Let's say, for example, I was listening to my music and pulled into a gas station. I pause my music so as not to bother others while I run inside real quick. While I am in there I get a phone call. When the caller gets sent to voicemail and the call ends from my phones side of things the music starts playing again. While it does work as a great way to know that I missed a call while I was out of my vehicle it does pose the problem of disturbing others around. Not sure if it is relevant, but I use several different apps for my music (YouTube, LiveXLive, Google Play Music, etc.) I have tried the option I saw on here of disabling autoplay entirely by rerouting the request through a different app when first connecting to a bluetooth device (can't remember the name of the app) but since the device is already connected and I have been listening to music already when the call comes in I'm pretty sure that is being overwritten when I start playing music. If anyone has any suggestions it would be greatly appreciated.
TLDR
1. Phone connects to car stereo via Bluetooth
2. I start listening to music
3. I pause music
4. I receive a phonecall
5. After call (even if not answered) music automatically starts playing again <-- *this is the part I want to fix*