What are the AT&T connection settings for a flashed Tilt - Tilt, TyTN II, MDA Vario III Windows Mobile ROM De

Hello -
I just got my tilt today and I've tried out a couple of ROMs already. On both of them everything seemed to work fine except the network connection. On the original config I connected just fine. I have an unlimited data plan and I have a good 3G signal around here. I found the comm manager but I'm not sure what settings to put in. Where can I find the settings?
thanks!

dhecker said:
Hello -
I just got my tilt today and I've tried out a couple of ROMs already. On both of them everything seemed to work fine except the network connection. On the original config I connected just fine. I have an unlimited data plan and I have a good 3G signal around here. I found the comm manager but I'm not sure what settings to put in. Where can I find the settings?
thanks!
Click to expand...
Click to collapse
Which rom are you currently running?
If the custom rom is based on and HTC rom, then after the flashing completed, you should have seen a notification for the Network Configuration Wizard. That will autoconfigure all of the required AT&T settings. I believe that the Network Wizard can be run from Settings --> Conections also.
If you check the Wiki for the Kaiser, you should be able to find a CAB file that will configure MEdia Net for you.

MediaNet
Cellular Line (GPRS, 3G)
Access Point = wap.cingular
User Name = [email protected]
Password = CINGULAR1
I use alternate DNS Servers (Under Advanced)
208.67.222.222
208.67.220.220
DNS is provided by Open DNS www.opendns.com
Dave

Related

WM6 proxy setting, quick help.

Hello.
I'm using faria's latest WM6 ROM, but can't find where to enter proxy server / proxy settings in accordance to t-mobile's guide. WM6 doesnt have the place where to enter proxy numbers as specified. After a little digging i heard you might need to change the settings in the registry for wm6.
Can anyone please advise?
Thanks!
12. Tap Edit my proxy server under T-Mobile GPRS.
13. Tap to check This network connects to the Internet.
14. Tap to check This network uses a proxy server to connect to the Internet.
15. Enter 216.155.165.050 in the Proxy server field.
16. Tap Advanced.
17. Tap HTTP.
18. Enter 8080 in the Port field.
Click to expand...
Click to collapse
I was able to configure mine just fine today, but I'll admit it took me a few tries in the past before I figured it out.
Go to Start --> Settings --> Connections tab --> Connections.
Since you're not using the standard T-Mobile ROM, just adapt the steps a bit to match up with what is on the WM6 ROM. Where it says T-Mobile GRPS in the instructions, actually use the My Work Network section on the device. You can also rename My Work Section to T-Mobile GRPS if you want.
Under that section, you should see:
Add a new modem connection
Add a new VPN server connection
Edit my proxy server
Other than the My Work Network/T-Mobile GPRS thing, the steps were exactly the same.
Oh yeah, instead of 216.165.155.050 enter 216.165.155.50.
I did that and I was able to get an Edge connection and send/receive MMS messages from my Verizon phone.
Dave
sgtcasey said:
You can also rename My Work Section to T-Mobile GRPS if you want.
Under that section, you should see:
Add a new modem connection
Click to expand...
Click to collapse
Hi.
When I goto Settings > Connection; "My Work" is no longer listed as a connection, only My Home.
How can i get back / add "My Work" ?
THanks.
Hmmm... I'm not sure. I have My ISP and My Work Network and I've always had that with the WM6 ROM's.
Dave
I know this is kind of buggy... I had the same issue.
If you add a new connection, call it My Work or something, and choose GPRS 3G for the type, and finish, it will put 2 connections, which will allow you to change between My Work Network again, etc. No registry hack needed, it's there, it's just not showing. By adding a 2nd connection, it will show your "My Work Network" again. Keep in mind, if you had MMS messaging, but no 'net until now, once the 'net works, you will have to change your MMS setting to "My Work Network" as well.
Now 'net and MMS works on my phone (Cingular 8525) on Tmobile, using only T-Zones and WM6 Thx for the help!

Just got a Touch Cruise

I am a long time reader newer poster. I am coming from a Treo 750. Is there anything I should do to this before I start adding my apps and transfering contacts? Is there a better backup of my Treo other than the Windows Vista Sync? I am mainly concerned with contacts and software. Also I am on Att I heard about the only thing I need to do is swap Sim card out, also should I adjust the wap settings for this to work. [email protected] password CINGULAR1. Also does it matter when syning new device the device name be the same? What is the best ROM I should have?
ATT
I also use att and all i have to do is set up the network to use media net and tell it under advanced to not use the proxy. It should work fine for you then. I am using Bepe rom 6.3 premium. The connection wizzard sets up right for ATT in the us except fothe proxy. you do npot have to enterthe wap settings they are there already.
Coming from my 750, I didn't have to do a thing - just stick in sim card and I was good to go. I am on the PDAConnect plan so no issues with proxies and such.
As for backup, use Sprite. It comes with the Cruise on the CD.
Thanks I will do that. I should have it in my hands tomorrow morning.
mpf54 said:
I also use att and all i have to do is set up the network to use media net and tell it under advanced to not use the proxy. It should work fine for you then. I am using Bepe rom 6.3 premium. The connection wizzard sets up right for ATT in the us except fothe proxy. you do npot have to enterthe wap settings they are there already.
Click to expand...
Click to collapse
I got my phone installed bepe rom premium, I thought I got all of the att settings correct I am able to receive sms and email but for some reason It only has edge when before the rom i was getting hsdpa and 3g speeds. can you please take me through a small tutorial of what excat settings I need in the connections panel. I have only 1 listed MEdiaNet I then went to the advanced network and it says: turn on HSDPA it is checked, GPRS PAP authentication is checked, CSD Line Type data rate 9600 bps(v.32) connection element Transparent, SMS Service SMS over GSM. What else do I need to do? Please help
Also under comm manager it shows no data connection available?????
I figured it out. I removed all settings and went through the connection wizard. Also I forgot to change the band type to auto, that is why I would only get edge speeds. I wasnt sure about the proxy settings, I was supposed to checkit not uncheck it. and found the server settings and port numbers. Thak for everything. This phone is so much better than the treo 750. Well worth the money. No more square screen for me.
Out of curiosity what do we need to set the proxy to? Is this for using tethering or something else? I am on ATT as well and the auto network configure app thing seems to have set it all up correctly. Is there anything additional to be done?

O2 MMS settings

Just started getting a problem with the MMS on my Serra and not sure if anyone can let me know theirs please.
Under connections/My ISP I have
Mobile Web - Cellular Line (GPRS,3G), mobile.o2.co.uk, o2web/password, DNS 193.113.200.200, Alt DNS 193.113.200.201
Mobile Web 2 - Cellular Line, mobile.o2.co.uk, o2web/password, DNS 193.113.200.200, Alt DNS 193.113.200.201
My Work Network
02 Active - Cellular Line (GPRS, 3G), wap.o2.co.uk, o2wap/password, user server specific
MMS Settings
o2uk - Gateway 193.113.200.195 port 8080, server address http://mmsc.mms.o2.co.uk:8002. Connect via My ISP
Thanks
Sorry all fixed myself, my proxy settings were incorrect
What exactly was the error - I still cannot get MMS to work even with your seetings from your post?
I found out that mine was that a proxy server was enabled. I hook mine up to my laptop while in the office to charge and activesync with my Exchange server. Hadn't realised that it also enables my office proxy server.
crazyC, is the SIM in your Serra on O2 contract or Pay and Go? I'm guessing it's the former, but if it's the latter I know the settings...
Is it just MMS that's not working, or is your data connection (via telephone I mean) not working either?
It was just MMS that did not work.
I am on contract, and after a lot of digging and trialling of cabs that should have fixed it, but didn't, I have sussed it out and tested it.
I will roll the settings into my O2 setup cab, test it, and then post it if anyone wants it.
YES! Please post it.
I am using these settings on my contract o2, htc touch pro. all my 3g and internet works... just no mms.
I have sat here for four hours now messing around with it...
any chance of posting the settings that worked for you?
Try this
MMS Settings
o2uk - Gateway 193.113.200.195 port 9201, server address http://mmsc.mms.o2.co.uk:8002. Connect via My Work Network
Other connections as per the normal O2 set up.
'My Work Network' shows up as O2 Active
Dont forget to set the O2MMS server as the default under MMS options
I havent tested this yet, but this cab SHOULD insert the O2 MMS settings - note you must already have the correct O2 network setup for calls and data, this is just the MMS bit.
im also having prblems with this, using the new Elite RC4. Im gunna reflash it and try again cuz i have fiddled with the settings too much
Edit - i tried the cab and the setting listed above it and neither worked for me
I have called O2 to see if they can help me and they sent me the some lame ass intruction which are exactly the same as on here... except afte you set up the o2web settings it says to use auto download for the rest :/
Whats the deal witht he proxy for the o2 active settings are they supposed to be on or off and if on, what do i set them as?
Installed the original O2 ROM to get all the settings working properly. It seems the missing details are in the WAP Proxy ones.
start - settings - connections - connection settings - manage existing under the 'my work network' (or whatever you renamed it too) - proxy (ensure use proxy is ticked) - advanced
WAP - 193.113.200.195:9201
SECURE WAP - 193.113.200.195:9203
Other than that settings are as they have been mentioned previously
MMS issues
I have extensively searched forum after forum and this seems to be the only thread with the sort of info i am searching for. I have installed TPC V3.1 Rom With required radio, everything works including MMS, however, no matter what settings i try i cannot receive normal sized pictures and any MMS videos go straight to the O2 website and all i get is a message your phone is not compatible with this type of message. Can anyone help, its really annoying............
I have tried the above .cab file and it doesn't work for me either.
Thanks in advance for any help.
O2 serra (raphael) win6.5, TPC v3.1 radio 1.14.25.05
Kevfm said:
I have extensively searched forum after forum and this seems to be the only thread with the sort of info i am searching for. I have installed TPC V3.1 Rom With required radio, everything works including MMS, however, no matter what settings i try i cannot receive normal sized pictures and any MMS videos go straight to the O2 website and all i get is a message your phone is not compatible with this type of message. Can anyone help, its really annoying............
I have tried the above .cab file and it doesn't work for me either.
Thanks in advance for any help.
O2 serra (raphael) win6.5, TPC v3.1 radio 1.14.25.05
Click to expand...
Click to collapse
Try some of these reg edits.
Thanks, but that is more for increasing the send size limit of mms, I can send them fine, but my network O2 cannot determine what phone I have and therefore only allows me to receive the smallest possible sized attachement.
I have tried numerous settings and radios to adjust this I've even tried the get settings feature and I get a txt back sorry we are unable to blah blah blah. with out going back to O2 stock rom i'm running out of options.......
Also I have never attemped to edit the registry
Again thank u for your reply......
EDIT......
Attempted reg edit, has had no affect, am I doing something Wrong.......?
o2 mms size problems
crazyC said:
I havent tested this yet, but this cab SHOULD insert the O2 MMS settings - note you must already have the correct O2 network setup for calls and data, this is just the MMS bit.
Click to expand...
Click to collapse
Hi guys, I have entered all the settings found on here and my mobile web and mms work but the mms messages received are resized to a tiny default size as mentioned on here.
Any chanch of an idiots guide to edit the registry so that o2 think it's another phone allowing me to received full size pics.
My phone is a Vodaphone UK HTC Touch Pro2 with O2 Pay Monthly Sim.
Any help is appreciated

Please help with at&t media net connection...

I have at&t service with the HTC Fuze and I downloaded this 2.1 Edition of manila. I am now (after downloading and installing) having a problem connecting to the internet.. Please tell me the media net settings nd stuff that actually works.. what about proxy settings?? and it won't let me turn on the data connection in the wireless manager saying, "cannot connect for an unknown reason. To check your connection settings and change them if neeeded, tap settings...". If you know a solution please help.. I also have the NATF v4.5S ATT WWE rom... so should I have the proxy settings on and off option thing that's available on the menu like on the BJ2?
Much Appreciated in advance...
There is a cab floating around that can automate this process of setting up your phone for ATT.
I would actually go get the official HTC ATT Rom update and use that to get back up and running, I do believe it has the newest manilla in it (I could be very wrong about this).
I use RRE roms so they are setup for ATT already.
Under connection settings...manage existing connections... I have only Media Net as a cellular line (GPRS, 3g) at access point name 'wap.cingular' with user name [email protected] and password ? with no domain present. Under advanced it is Use Server Assinged IP and that is it.
Go to Settings\Connections\Connections\
Click on manage existing connections and go to Proxy settings.
Take out any proxy and check 'connects to the internet' and uncheck 'uses proxy'.
Click okay and in previous screen go to Advanced\Select Network and set both to MediaNet.
This should resolve any connnectivity issues.

[Q] LG Quantum/Mango can't connect to TellMe server

I have a Bell unlocked Quantum running on Telus that will not connect to TellMe server via data connection. Works fine when tethered or through wifi.
Is there a old Bell setting that blocks it from connecting through telus?
I have setup the Telus APN settings.
Thanks.
Alti20 said:
I have a Bell unlocked Quantum running on Telus that will not connect to TellMe server via data connection. Works fine when tethered or through wifi.
Is there a old Bell setting that blocks it from connecting through telus?
I have setup the Telus APN settings.
Thanks.
Click to expand...
Click to collapse
go into mfg, engineering menu and click other options "edit your apn"
set to telus from in there.
You need to change that apn also
It's already set to sp.telus.com in mfg as well, all the other APN fields are empty.
make sure the proxy setting is disable in MFG also
It's set to "Off"
I checked the current profile and it still shows a bunch of Bell settings (i.e CM_ProxyEntries, MMSProxy etc).
I figured it out, last posting sort of clued me in, network profile needed to be updatd.
1.) MFG / Engineer menu
2.) Other setting
3.) Set network profiles
4.) Entered MCC=302 MNC=202
5.) Clicked Find
6.) Installed profile tls_ca_302_220_eng.xml
All is good now!!!
Thanks.

Categories

Resources