Database Info

ERROR 262 - Bricked phone with Radio Rom Upgrade - SOLVED -

Hi to all,
I have an AT&T TILT HTC 8925,
ROM: 1.57.502.2
RADIO: 1.27.12.11
VE: 22.45.88.07H
Installed the kaiser-HardSPLv1 with no problems.
After this I Flashed (via USB) Q-Mobile_v1.2 ROM, that went perfect. Made a soft reset and then a Hard Reset after this I configured the phone.
After everything was working I made a Radio flash with KAIS Radio Only 1.27.12.17 CustomRUU, all seemed normal until it got to 95%, it suddenly interrupted the update (error 262), and took me to recovery dialog 1-4 steps which I did.
From that moment until know I get the tricolor screen with the following text:
RUUNBH​KAIS 1*0
SPL-1.56.0000
CPLD-8
USB​
Click to expand...
Click to collapse
And when I try to flash ANY ROM, It gets past the tricolor screen, to a white screen with a percentage bar that gets to 0%, after a minute or so the customRUU screen goes to error 262 and I get to the recovery screen, etc...
I run on WinXP SP2, and have already tried several roms with the same result, with the exception of original ATT RUU_Kaiser_CINGULAR_WWE_.exe, it then gets to 1% and displays error code 294 Invalid Vendor ID.
When I tried the MicroSD method with the rom it gets to the tricolor then the "Loading..." screen, and keeps there (I waited for about 30 min)...
There was no SIM or MicroSD card on the phone at the moment of flashing, and I did dump the original ROM to the 4 raw parts as per instructions.
I live waaay out of the countries with AT&T or HTC servicing routes, so I am stuck with it until I fix it, which I know I can do, and to be honest with myself, can't afford to waste the money spent on this thing.
Until now the best similar thing I found about this was with the hermes unbrick phone thread, and I am not sure this works on the KAISER, but to be honest, I get cold sweats to use any more procedures (without reconfirmation) on this as I have a phone that at least still shows "some" signs of life.
After reading days of threads (my eyes are burning) I know the knowledge is within this site, but I need guidance since I am new to this thing (smartphone flashing) although familiar with computers.
Any kind of help will be very appreciated and valued.
Best Regards.
----------------------
As an update, I solved this thing. Thanks for your help.
After seeing that there was some sort of problem with the boot mode screen not showing the kaiser-HardSPL data, I went in that direction. After some suggestions and much trying I decided to download all / any original roms I found in here for my phone (ATT Tilt) then I worked my way from top to bottom based on the versions of the radio.
The one that solved my problem was 1.5.502.3 Radio 1.27.12.11 although strangely it shows on my phone after the successful flashing. 1.5.502.1
Just out of curiosity I went and installed again kaiser-HardSPLv1 and it gets to this text on tricolor screen:
Kais1*0
SPL-.JumpSPL
CPLD-8
Doing a hard reboot (camera button + soft reset) gives me a different screen:
Kais1*0
SPL - 1.56.0000
CPLD-8
Really don't know if this is normal, and after flashing a cooked rom I had to reinstall it (kaiser-HardSPL).
I have now reflashed QMobile rom and have no problems. Although I didn't flashed again new radios
For flashing the Original rom I did make sure of the following steps in addition to normal ones (Just in case)
1) Disconnected fisically from LAN (Unplugged LAN Cable)
2) Disabled all firewall protections
3) Disabled all antivirus and spyware protections
4) Run RUU original files
5) Pray
Thanks again people

I had the same issue (I mean exactly the same). After failing the radio upgrade (Luckily I had my trusty Universal, so I started playing around (MTTY, Radio Roms etc.). The only thing that saved my TytnII was the original ROM!!
ftp://ftp.xda-developers.com/Uploads/Kaiser/Roms/

I just tried it again (See I am not so scared anymore), and received the same results (Radio upgrade fails on 95%).
I have burned the original ROM back and all is well again!

I also can't get past the same screen and try as I might Activesync won't recognise the phone. When going through the recovery process on Kaiser Custom RUU it says its recovered but then when trying to go through the update it sticks on 0% and then says there are communication problems etc.
On the tricloloured screen it says
KAIS130
SPL-1.81.0000
CPLD-8
Will a hard reset do anything?
Any help much appreciated.

Bump
Now managed to boot via MTTY but power off etc returns me to bootloader screen

Looks to me like you guys have had problems flashing hardspl. Your tri-colour screen should have:
KAIS130 MFG (or Kais 120 etc)
SPL-1.0OliPof
CPLD-8
I don't know about the CPLD number but you MUST have the OliPof SPL. Check this after running hardSPL to make sure that it's there before flashing another ROM.
If you have this but still get trouble flashing, try going to the tri-colour screen and then run the kaiser_RUU.exe to upgrade.

http://forum.xda-developers.com/sho...ked. (One without a radio)
- Flash a radio...

i had the same thing with my MDA Vario 3,but with no success finding the original ROM, since I`m from a small country. I`ve tried to reboot to normal screen via MTTY but it gives me the error: Command error . So - now I`m left with two options: to dump and reconstruct an original ROM from the same type of phone or to find what`s wrong with MTTY.
Anyone had a similar problem, I mean with MTTY and command error???
yes, i`ve searched trough the posts regarding this problem but I didn`t find any saying that MTTY gave this error.
any idea?
THX in advance!

Focus on HARD-SPL - get that on the phone and make sure its there.
If you cant get it on try this method:
http://forum.xda-developers.com/showthread.php?t=354061

Martinhdk said:
Focus on HARD-SPL - get that on the phone and make sure its there.
If you cant get it on try this method:
http://forum.xda-developers.com/showthread.php?t=354061
Click to expand...
Click to collapse
if you`re reffering to my problem-how can I copy the JumpSPL1.56-KAIS.exe file and execute it from the phone if I can`t boot it normaly,it always stays in tri-color boot screen?
actually, I`ve bricked my phone with that HardSPL procedure.It was the first step for unlocking. I`ve copied the JumpSPL1.56-KAIS.exe file, executed it and then rebooted and tried to flash with the modified ROM from the jockyw2001`s unlocker. it stopped at 95% and now it seems that it is still CID locked and bricked in boot mode. i`ve already said what MTTY gives as an error.
any idea what may be the problem?

like always:the problem is in RTFM
while i was working on my Kaiser i was doing lots of other things on other computers so i`ve skipped the step with flashing the HardSPL,that`s why all went wrong now,as i`m at home i have more time to read the posts and i`ll try with the jockyw2001`s procedure from the MTTY, with the task8 command.
hope it will help,unless the only solution is to dump the same ROM....
i`ll higly apreciate if anyone has a different solution....
will post results

The problem is that I can't flash the phone with anything be that HardSPL or the original Orange ROM or whatever you care to mention because the PC can't communicate with the device via the USB cable after Activesync ceases to operate. As such everything works up until the % progress bars come on both screens and then they stay at 0% before the communication error message appears.
Funny thing is that the phone is communicating with the PC as USB/Serial alternate depending on whether the cable is plugged in or not and the PC recognises the USB device when its plugged in and when Activesync isn't controlling the situation.

I've been stuck like this with a Hermes but not the Kaiser (yet). As far as I'm aware, you don't need activesync running to run a rom upgrade. If you are in bootloader mode (tricolour screen) you can run the upgrade directly with activesync not connected. If hardspl isn't installed then you should flash the original rom, and if you're unlocked then any rom should do.
Also it might be worth trying the SD card method for flashing. But either way I'd use the original rom and then when you get the phone working again keep trying with HardSPL until it's successful - don't flash any other roms without it.

Laubscherc said:
I had the same issue (I mean exactly the same). After failing the radio upgrade (Luckily I had my trusty Universal, so I started playing around (MTTY, Radio Roms etc.). The only thing that saved my TytnII was the original ROM!!
ftp://ftp.xda-developers.com/Uploads/Kaiser/Roms/
Click to expand...
Click to collapse
Thanks for your help.
I did try other "original" rom I got in here http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
The version corresponding my rom is (1.57.502.2 (radio 1.27.12.11)), however I got the error code 294 Invalid Vendor ID after 1%.
I did try the ftp address you mentioned, but I can't login neither anonymously nor with user & psw for xda-developers.
I would like to try the rom you are referring to, please give me another link to download the file.
Best Regards.

Martinhdk said:
http://forum.xda-developers.com/sho...ardware devices list.
Thanks for your help.:)
Click to expand...
Click to collapse

Stuck in Tri color screen
I have been fighting the same issue for several days. Radio gets to 95% and errors. Then hung up in tri color screen. I used MTTY - "set 14 0" command then "boot" command inMTTY to get the phone to boot. I have had to do this a number of times, sometimes more than once per incident. Hope it works for you too. P.S. once you have a successful flash the phone returns to normal operation until then it will go back to tri color screen on reset. I just flashed a startup splash screen to get mine back to normal.

pennco can you expand in further detail on what you actually did with MTTY cause I have the EXACT same problem....

Is it dead

I have a situation with m600 when powering on theres a green screen like the bootscreen but all green and it only shows ipl spl and os. the operator logo has gone it wont connect to active sync from OS i can get usb bootloader have tried everything apart from the microwave.

Electronburn said:
I have a situation with m600 when powering on theres a green screen like the bootscreen but all green and it only shows ipl spl and os. the operator logo has gone it wont connect to active sync from OS i can get usb bootloader have tried everything apart from the microwave.
Click to expand...
Click to collapse
Why do you put a M600 post in the Prophet forum? (edit: sorry just confused with the device ETEN M600 from Hong Kong here )
1. Anyway, what had you done to your device? .....(edit: message deleted)

Why do you put a M600 post in the Prophet forum?
Click to expand...
Click to collapse
They're the same device damnit!
I have a situation with m600 when powering on theres a green screen like the bootscreen but all green and it only shows ipl spl and os. the operator logo has gone it wont connect to active sync from OS i can get usb bootloader have tried everything apart from the microwave.
Click to expand...
Click to collapse
If you disable connect through USB in activesync, then plugin the device, and then run a WM5 (AKU2.2) No Vendor ROM (Check the Wiki or the FTP server). You should be able to recover your device.
It does sound like a failed upgrade, but it should be fixable.

Electronburn said:
I have a situation with m600 when powering on theres a green screen like the bootscreen but all green and it only shows ipl spl and os. the operator logo has gone it wont connect to active sync from OS i can get usb bootloader have tried everything apart from the microwave.
Click to expand...
Click to collapse
OK,
if your device can fall into the bootloader mode, you can save it easily.
1. force device to bootloader mode manually (please see howto in the link within my signature),
2. ooops, before that, you should had prepared(downloaded) the PVtemp or NVID to flash your device to WM5. (also provided in my thread),
YOU CAN DO IT !!​

Electronburn said:
I have a situation with m600 when powering on theres a green screen like the bootscreen but all green and it only shows ipl spl and os. the operator logo has gone it wont connect to active sync from OS i can get usb bootloader have tried everything apart from the microwave.
Click to expand...
Click to collapse
this is very simple
soft reset and press and hold camera button
and upgrade. enjoy it.

Kaiser boots to Tri-color screen unless I use mtty boot command, help...

ok this is the wierdest thing ever. Yesterday I soft reset my phone (which was flashed to HardSPL and SuperCID and the Hyperdragod II rom about 2 weeks ago) and it now only goes to the bootloader screen. I ran mtty and did a boot command and the phone boots! But as soon as I softreset it goes back to the bootloader screen. Please note it wasnt a bad flash or anything because since I flashed 2 weeks ago my phone has worked 100% fine, soft resets and everything worked. I tried flashing to the original Kaiser bootloader, I flashed back to the original HTC rom and it still does this. One thing I noticed is that when I use mtty to boot and plug in my phone via usb my Windows XP PC doesnt start activesync, windows says it cannot recognize the plugged in usb device! However in tricolor mode I can still flash 100% so I dont think the usb port is defective.

same here..
the phone was hanging at night... wanted to reboot.. and tricolor..
Now I am using it for months.. an something it boots ok and sometimes I have to use MTTY or waiting without the battery in it for 10 min solves it sometimes to.
gone install 6.1 now.. hope it fixes it.

what does it display at bootloader screen?

sorry to jump in, but mine's started doing this today.
I had it flashed with 'Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid V2_1_65.14.06', which seemed to be working OK.
Then I soft reset it earlier today and got to loading my tday screen, screamed the battery was dead (it was nearly fully charged) and turned off.
I turned it back on and it was as though it was booting after the soft reset, or like I'd taken the battery out (I hadn't).
I couldn't get this to change, so I flashed it with Sleuth v3.0, one ive used very successfully before - now it only shows the tri-colour bootloader screen, with the following details:
KAIS130 MFG
SPL-1.0.0.oliPoF
CPLD-8
USB
Anyone know what I can do?
Thanks in advance
'tunes

Do the letters RUUNBH appear anywhere on the screen. LOOK AGAIN!
If so I can help easily, if not It'll take a little homework on your part. Let me know.

the exact text from the bootloader screen is:
KAIS130 MFG
SPL-1.0.OLIPOF
CPLD-8
Down the bottom it says Serial, or USB if it's connected to my PC.
(these may have changed from earlier, ive been trying all sorts to get this going properly!)
Thanks for your help

mad_tunes said:
the exact text from the bootloader screen is:
KAIS130 MFG
SPL-1.0.OLIPOF
CPLD-8
Down the bottom it says Serial, or USB if it's connected to my PC.
(these may have changed from earlier, ive been trying all sorts to get this going properly!)
Thanks for your help
Click to expand...
Click to collapse
I answered you in the other thread. Use one thread for correspondence, we don't need 15 different threads & posts about the same thing.

Help!
I have the same problem descripted in this thread but I wasn't able to find the other thread you are talking about with the answer... Is there anybody here who would help an unlucky tytn2 owner? Thank you so much... I'm waiting for you!

What is wrong with my phone? Tried to Flash new Rom...Black Screen

Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....

ahh that sounds like a nightmare... wish i could help

klrob33 said:
Okay. I tried to install one of Dutty's ROM's that can be found here: http://forum.xda-developers.com/showthread.php?t=398271.
I read through all the stickys and FAQ's first. I read Dutty's wiki, the Kaiser wiki, and the flashing new ROM wiki. I followed all of the directions and followed Dutty's instructions to the T.
After installing the HardSPL found here(http://forum.xda-developers.com/showthread.php?t=334679), I backed up all my personal info/data.
Then used the Custom RUU Dutty supplied and proceed through the ROM flashing process. Everything went fine and I got no error messages. But when my phone booted up I got a black screen. I waited but my phone stayed on the black screen. So I pressed the standby button on and off a few times and eventually I wound up with a black screen that had about a million multi-colored speckled dots all over it. And I have been stuck on this screen since. I've tried soft-reseting and hard resetting but nothing is working.
I am Using an ATT Tilt BTW.
Please Help me. My phone is my life so right now I'm feeling like Dionne Farris.....Hopeless....
Click to expand...
Click to collapse
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device

redbandana said:
can you get into bootloader mode?
hold down power and camera button while inserting stylus it should introduce you to the tri color screen. Please tell us what it states. You may have just experienced a bad flash or you have the radio from hell installed on your device
Click to expand...
Click to collapse
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.

klrob33 said:
Yes I can get to Bootloader mode.
In the red bar it says:
KAIS1*0 MFG
SPL-1.0.OliPof
CPLD-8
And Serial at the bottom in the white bar where USB normaly would be.
Click to expand...
Click to collapse
ok soft reset your phone and when it starts up does something like this appear in red text?
r 1.65.20.29
g 25.88.40.04w
d 3.29.xx.xx
please tell me what it says after R

R- 1.58.25.17

klrob33 said:
R- 1.58.25.17
Click to expand...
Click to collapse
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit

I had the same problem, what i did was read all through the thread of the ROM or while inside the thread i use the search function and type in the keywords like "blank screen" it happened to me exactly, but i didnt bother to post since i found the answer, 1 user said flash it to WM 6.1 i did exactly that and it helped! some said not necessary, but i didnt see that instruction so i flashed the 6.1 blindly and fortunately it worked...
here is the thread
http://forum.xda-developers.com/showthread.php?t=375583&page=30
on the search function type black screen and you should get and idea what you need to do...

redbandana said:
well it appears to be a bad flash. unplug your device from the usb cable, restart your computer, and flash again.
Hopefully after your computer restarts it will recognize the device as being connected. If it doesn't just double click on your windows mobile device center icon and it should connect. After connecting just reflash the rom
edit
Click to expand...
Click to collapse
I tried that and It different work. I'm trying a whole new ROM now and I hope it works.

Problem solved.
Thanks to everybody for their help.
I just used a different ROM and everything worked perfectly. I guess that ROM just didn't want to work with my phone. But it's okay. The ROM I'm using now is perfect.

Qtek S200 flashing problems

Hi,
I have a Qtec S200. G3
Now the problem is that I cannot flash it:
a) Using Softspl: the device screen sometimes turns bright white as it should, but when I start a RomUpdateUtility_NV_G3 it does not find my PDA
It tells to check my USB connections, which are ok.
b) Using Hardspl G3 found here, also at first produced the White screen, and when it came to the rom updating part, next, next, update-> the PDA screen turned black and eventually it could not connect to the PDA, displayed the same USB connection error.
c) Prophet Tools 2.8.3
Hardspl & Softspl are practically unusable, the same thing happens as above, softspl shows promise by entering into the "Bright white screen" state, but even then, when trying to "put" or "update" a rom to the pda in that bright white screen state, it still turns the screen black and does nothing, same connection error as before.
What could be the cause of this?
Any help would be appreciated
Details:
IPL 2.09
SPL 2.09.0000
GSM 02.07.20
OS 2.9.7.24

Help, anyone?

Help.. i have the same exact type of phone and the same error.. Can't get into SoftSPL and HardSPL doesnt work either. Really tired of WM5, nomatter how good it is

Today i tried to upgrade the IPL from 2.09 to 2.10 but still nothing. When i start the upgrade the phone turns off and wont start again until i pull the batter...
Any if all help would be welcome!

After a year i'm still stuck with this old ROM and the same problem as before.

Bump... Really could use some help on this

Same problem here
My S200 has the same issues.
But today when i tried to upgrade the IPL/SPL to 2.20 it worked and i was even able to hard spl .
I think the problem might be with the battery.Have you guys checked that out?
As for me,i am able to start flashing roms but the phone gets disconnected automatically in between.
I am going to try a whole night recharging and then flashing.
lets see if battery is the villain

my qtek s200 is mad
i tried to upgrade my rom from w to w6,and because i don't know how to do?my s200 has become unusable without charger,when hard reset it doesn't complete install process and it blocked,restarting it works unproperly,bud comands no sound no ...unpluging charger it turns off,battery is full "i'm sure ",but it indicate it empty 0% ???,
how can i syncronise it to pc and it is off
ipl 1.01
spl 2.20.0000
gsm 01.12.10
os 1.5.4.2
pleeeeeeeeeeeeeaaaaaaaaaaase heeeeeeeeeeeeeelp

Tomorrow i will try with my new battery..
Sofar, i know it boots into the 3 colour stripe menu when using RUU program and that's it, program crashes and phone stays the same..
Really hope battery is the solution..

BAttery change didnt do anything, still the same old ... cant upgrade.. anyone know if there is some upgrade block on some models?

BUmp.. the only phone i have been unable to flash is the S200.. ANY advice left in anybody?