Database Info

My Universal is compeletly down

Hi, I tried to install WM 6.1
but i think i installed wrong version to for universal and its now compeletly dead even i can not access the boot loader
any one can help me please

aahmed12 said:
Hi, I tried to install WM 6.1
but i think i installed wrong version to for universal and its now compeletly dead even i can not access the boot loader
any one can help me please
Click to expand...
Click to collapse
remove tha battery, wait two mins and re-insert the battery, power on the device and try to enter bootloader. If you can now access the bootloader, format the DOC with MTTY (instructions are in the Wiki) If you still cannot access bootloader mode, do you have any leds lit?
Cheers,
Beasty

yes I have red lit form time to time when i connect it to the usb
but nothing at all

to enter the boot loader while ur device is off u press backlight+power withiout the restart botton .. i dunno if u already know that

Hey, I've met the same problem as yours. After I used MTTY to clear DOC, my D900 was totally down, even I could not access the BL (I've tried more 20 times). Then I changed the battery to another one, and press Power+Light+Reset, 2 minutes later the BL screen appeared! I flashed the ROM again, my D900 is working well now~

Kaiser stuck on green WM6.1 clear memory screen

I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?

bsgbelg said:
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
Click to expand...
Click to collapse
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!

Not possible to flash anything
what I've tried so far:
- activate active sync to install hardSPL. Not working
- install HardSPL through microSD. Not working
- install ROM through SD. Not working
I tried a non HCSD for a change, and then I see the loading scree flashing up, but quickly says No rom found and returns to the bootloader screen.
The only thing that works is load the bootloader (red green blue white) into a screen that says:
KAIS130
SPL-3.29.0000
CPLD-8
Serial
When connected to USB, it says USB, but no disk is showing in Explorer or any connection is made to AS
The only thing I've done in the past is flash the 6.1 rom through the system provided by HTC with a file called RUU_Kaiser_HTC_NLD_3.29.404.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe
Please help, I really like this phone and hate to loose it

put it into bootloader, connect it to the computer and then flash one of the htc roms. make sure its an htc rom, you cant flash a custom rom cause you dont have hardspl

I have not been able to find the original rom, only the exe from htc which says Connect with active sync. Do I have to set it in bootloader and then execute the program?

Solved
Just want to let you know I sorted it out!
Flashing the original rom does not need active sync, the bootloader USB connection is sufficient.
After this, the phone restarted in 'Erasing memory' mode, but was able to finish it and reinstall the whole rom.
I believe I got the taste of it and will start testing some other roms...

msd24200 said:
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Click to expand...
Click to collapse
Thanks, worked fine

majedaly said:
Thanks, worked fine
Click to expand...
Click to collapse
good to know

Urgent Help Did I Brick My TP2

Please help.
I have the Verizon TP World Phone w/SIM card.
I downloaded the HARDSPL described as such: this package is for Rhodium CDMA-GSM worldphone version only (CDMA Touch Pro 2, not the original Touch Pro) devices. only RHOD400, RHOD500 modelids are accepted. this Hard-SPL supports WM6.5.
This process went successfully and I made it to the tri-color bootloader screen.
Next I ran this flashed this ROM NRGZ 21864, which appeared to complete successfully via PC, but when phone rebooted it just shows black w/Touch Pro 2 in middle of the screen.
Tried resetting, batter pull everything can't get anything to happen.
**Update: I was able to now get it into tri-color boot loader so what should I do with it now? It says SPL-1.00.Olinex, so its still unlocked. Should I just retry the rom again?
What did I do wrong? Is this phone dead? How do I get to bootloader? What should be my next step if phone is not dead.
Thank you!!!

Get a different rom that one didnt load or you could try reflashing doesnt seem as it took properly but no fears your phone is not bricked
Make sure you get a rom built for CDMA phones. this isnt the proper section for that goto RHODUIM CDMA

To Flash from the SD card, the .nbh file needs to be named "RHODIMG.nbh"
copy the .nbh file to a micro sd card, prefarably a 2gb or lower formatted as a FAT32
plug it in
get into the boot loader
i would recommend getting the stock ROM for your carrier and flashing that before moving to a custom ROM
hope that helps

ME TO
How do you get it to load in the bootloader menu ? Any luck with fixing it?

LECKEY73 said:
How do you get it to load in the bootloader menu ? Any luck with fixing it?
Click to expand...
Click to collapse
To enter the bootloader hold volume down and power (the red end key, not the sleep key on top) and press the stylus into the reset button. Once you see the tri-color screen you can release volume and power.

Same thing happened to me on my flash to that exact ROM. I guess sometimes it just doesn't flash correctly for some reason. No worries, enter bootloader mode and try flashing to MightyROM. After that, I was able to flash to whatever ROM I wanted. (But then I flashed back...MightyRom rules!!)

the spl 1.00 is fine. just go here it's for cdma phones only.

thanks everyone, got it back into bootloader via the challenging (hold both buttons and hit reset) Years of cosole gaming clearly paid off for those acrobatics.
Reflashed to original rom/radio, will put MightyRom back on..think I just needed to bump my head a bit, start over after some lessons and get this running better.

[Q] ;Help please. Can't get my Touch Pro's boot to start

Hello
I've flashed my Touch Pro several times in the past 2 years and everything went always OK. The last time I've flashed with TAELROM_v5.23138_17SEP2010
Everything went OK for several days, until yesterday:
1. battery drained very quick after full charge (6 hours);
2. Can't put it to charge again;
3. Can't wake it up, even with other battery fully charged;
4. No boot menu;
5. With just access to bootloader mode
Some info:
Is the device HardSPL'ed
Yes: SPL-1.90.Olinex
Is the device unlocked
Yes
Access to bootloader mode (tricolour screen)
Yes (won't start the phone even if I try to soft reset in bootloader mode)
How can I revive?
Thanks in advance

If you can get into the bootloader just plug it into your usb port and flash a new ROM.

I've done it already, and the problem stays the same... Although the installation runs normally, after reinstall the phone doesn't restarts unless in bootloader mode!
Could it be a hardware problem?

Try pulling the sd card (and maybe the SIM card) and resetting. A corrupted sd card could jack up the device.

Farmer Ted said:
Try pulling the sd card (and maybe the SIM card) and resetting. A corrupted sd card could jack up the device.
Click to expand...
Click to collapse
if that does not help then is something wrong with hardware probably.
I always pull out sd card and sim before flashing with new rom just to avoid that kind of problems.

expert.. help me please..
i also have same problem as u'r.. the device stuck in 3 color bootloader, i already flash it with original factory rom, but nothin' change.. try using axe box to create goldcard, but the problem still not solve. can somebody help me pls...
1. when updating with factory rom (RUU_Raphael_hTC_Asia_5.07.707.2_signed_Raphael_52.58.35.30_1.11.25.01ship) it stuck at 25%
-message: error(226): flash write -iu634
2. when updating via sd card the message that appear is -updating failed, wrong OS..
what should i do next to survive my lovely phone?

My advice in this case is: try task29 before flashing your rom (without sd- and simcard in TP)

so, what i should do now my friends?

borisku said:
My advice in this case is: try task29 before flashing your rom (without sd- and simcard in TP)[already doing task29, but nothin' happen.. pls help me if u hv another solution.. ]
Click to expand...
Click to collapse

what would i do?: I would flash bootscreen via task29, then (different?) radio, then a different (stock?) rom. If that doesnt help, i dont know more, sorry... good luck
btw ehhhm: Your phone is a gsm, isnt it?

rumpang said:
i also have same problem as u'r.. the device stuck in 3 color bootloader, i already flash it with original factory rom, but nothin' change.. try using axe box to create goldcard, but the problem still not solve. can somebody help me pls...
1. when updating with factory rom (RUU_Raphael_hTC_Asia_5.07.707.2_signed_Raphael_52.58.35.30_1.11.25.01ship) it stuck at 25%
-message: error(226): flash write -iu634
2. when updating via sd card the message that appear is -updating failed, wrong OS..
what should i do next to survive my lovely phone?
Click to expand...
Click to collapse
Do you have hard spl? Or were you flashing a stock rom with a gold card? I would try flashing the stock rom for your device/carrier. You may be screwed, if you don't have hard spl.

In my case, the problem was hardware: charging malfunction.
Thanks to all of you who helped me

Farmer Ted said:
Do you have hard spl? Or were you flashing a stock rom with a gold card? I would try flashing the stock rom for your device/carrier. You may be screwed, if you don't have hard spl.[yes, i already flashing stock rom with gold card, but before the problem, i install the rom without hspl, that is my fault! anyway, do you have solution for this? ]
Click to expand...
Click to collapse

yes, my phone is gsm..

If you can get into bootloader, then try flashing hard spl. Then flash whatever you want.

i can get into bootloader mode, but d device can't flash with hspl (RaphaelHardSPL-Unsigned_190_1_3), it only stuck at 0%. try flashing hspl with sd card with no success. any other way to flash d hspl? do i need to flashing with the factory rom that has 1.9xxx spl? My SPL is 5.07.0000.. I need ur ADVICE Sir.. TQ..

[Problem] Flashing HardSpl trough MicroSD fail (pls help)

I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.

You can't flash hard spl off your sd card; it's got to be done through a usb cable.
Just read through the hard spl thread; it's long, but your situation has probably been addressed. I did it almost 3 years ago, so I don't remember the tricks. That's the case with most posters, I'm afraid. Just read the thread.

can u pls tell me which thread?
this one?: http://forum.xda-developers.com/showthread.php?t=410150
or this one?: http://forum.xda-developers.com/showthread.php?t=448008

Either, but read the first one. You can also look in the unlocker thread. Hell, you may just want to buy the unlocker and run that. It will flash hard spl, and the directions may be better.

I just hope they aren't trying to HSPL(hard SPL) a CDMA device :S I've made the mistake to assume the person that was posting in this forum had a GSM device and they really screwed up after a third attempt at flashing HSPL!
Usually if I have a difficult time flashing my Fuze or TP(both GSM), I remove everything to include the battery, connect the USB to an available USB port on the computer then hold the volume down key while connecting the device to the USB cable. Probably not the most friendly way but it certainly will tell you if there is a problem with your USB port/cable or even device!

My htc raphael is GSM
I've tried to hold the volume down button but it's always the same
There's no problem with the cable just that I can't flash anything because I'm stuck with a stock-spl and I can't flash a hard-spl either. When I try to flash something from the computer it starts to flashing with 0% then nothing happends until the RUU gives me the 262 Error. And when i try to flash from my mSD it just stuck with a Loading screen.

Xadow said:
I had a StockSpl on my Htc touch pro and I wanted to flash an unsigned Hard-SPL from my MicroSD because I wasn't home and I didn't have the USB cable. After the screen loaded 100% the device restarted I took off the MicroSD and now it keep showing this tri-color screen:
RUUNBH
RAPH100
SPL-1.90.000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
Upgrade ROM code error
Please try again
Serial.
(I've also attached a picture)
If i try to flash again from MicroSD the same HSPL it loads until 100% then restart and start to load again until i get the MicroSD card off. Or if i try to flash other StackSPL or any other ROM it stays on Loading on a grey screen.
After I went home I tried to flash the HSPL again from my computer using the USB cable, it start to load 0% then it does nothing. I've tried to flash StockSpl and other ROMs from the computer too but it does the same.
I think i've tried anything but nothing seems to work ... if someone can help me pls ... i've searched the entire forum and there's someone that had almost the same problem here: http://forum.xda-developers.com/showthread.php?t=566796
but noone had any solutions.
Click to expand...
Click to collapse
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.

mskip said:
Naughty Naughty..
I guess you realise now that you should ALWAYS read read read before modifying your phone in any way.
What EXACT file did you originally flash to your phone via microsd card and where did you get it from?
If you go into the bootloader screen and then connect the usb cable does it show "usb" at the bottom of the screen?
PLEASE STOP TRYING TO FLASH HARDSPL FROM MICROSD AS YOU CANT DO IT. If you could then it would be in my guide..
Mark.
Click to expand...
Click to collapse
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again

I guess I missed the part in the OP where you said it was stuck in bootloader. That's not good. I would try flashing the stock raphael rom (assuming you have it). Have you tried that? I dunno, you may be stuck for good.

Xadow said:
Thanks for replying
Yes ... I did read the part with the SD flashing but i thought it's not a bit deal to flash from mSD since the flashing via activesync is so easy.
Well ... i extracted the RUU_Signed.nbh from the Hard-SPL found HERE and i copied it to the mSD (MicroSD) and renamed it RAPHIMG.nbh.
I restarted my phone holding the volume down button and it started to load until 100% then it restarted and showed the bootloader screen and after a couple of seconds start to flash the HSPL again so after it completed 2 or 3 times of flashing and restarted i took the battery and the mSD off (I DIDN'T TOOK THE BATTERY WHILE IT WAS IN THE PROCESS OF FLASHING). And when i started the phone again without mSD it showed the bootloader screen like it was waiting to get a .nbh file on mSD to start flashing again.
No matter what i do my phone start in bootloader and down it shows "Serial". If i connect the usb it shows "USB".
I tryed to do a hard reset and it seem to work but after it finish and the phone restarts is stuck with the same tri-colour screen.
Sry for trouble and thx again
Click to expand...
Click to collapse
As Farmer Ted said your best bet now is to download your ORIGINAL Rom (from your provider) and flash it from your pc with the usb cable attached. The phone had to be in SSPL mode before running the RUU which is why everything was packed in a single exe. You may have corrupted your SPL in which case you have bricked your phone but if you can manage to flash a Stock Rom then the Stock SPL should be reflashed and you can start again with the HardSPL by following the CORRECT instructions and not making up your own lol.
Good luck.
Mark.

When i bought my phone, the first thing i did was to dump the rom. So now i rebuild it from raw and tried to flash but it didn't work so i went to Orange site and i downloaded the official ROM then started to flash and ... IT WORKS
I think that the ROM was corrupted not the SPL, and since the SPL was stock it didn't allow me to flash other ROMs other then the official
Thanks for all guys I couldn't done this without your help
P.S: why did it allowed me to flash the official rom but the hspl not?

It didn't flash the hard spl because you did it all wrong; those rebuilt roms aren't exactly the same as the stock roms, so it's not surprising that wouldn't flash. Good job finding the original shipped one, though.
Now, just read mskip's instructions and you should be good to go. I think the trick is just to enter bootloader, then connect to your pc through the usb cable.