problem with upgrading to WM6 - JASJAR, XDA Exec, MDA Pro ROM Development

while upgrading to WM6, my dopod 900 turn black... now cannot turn one... anyone got any advice what to do??? i try to hardreset, when i press 0 to clear it turn black again...
can someone pls tell me what to do..
Thanks

I have had this happen too
I also have had this happen several times.
The device seems to return to bootloader mode.
If you look at the screen carefully in bright light, you will see Bootloader vX.X
Just reflash with another ROM that you know is good.
Use Jwrightmcps ROM and select the dopod 900 link
Here is a copy of the link.
http://vidmes.com/Uni/ROMs/Jwrightmcps/2.12.04/WWE/900_WWE_21204_21207_11500.zip
Good Luck

saferty please unlock SIM/CID before upgrade new ROM.
then take out sim and storage card.
- make your PDA in bootloader mod.
- unselect usb connecting in activesyn
upgrade a new ROM.
be careful: do not turn off power and disconnect cab during upgrading

Related

Updating Qtek S200 ROM has cell phone locked in Boot loader

Hi there,
I bought a Qtek S200 and I tried to do a ROM upgrade. I followed the instructions given in the website http://kimpeacocke.blogspot.com/2006/06/how-to-perform-rom-upgrade-on-your-i.html
I got the upgrade from this site at ftp://xda:[email protected]_022021_Dopod_PDAMobizEdition_v101.zip
I followed the procedure given in the website given above. After I upgraded successfully the phone has become locked in the boot loader screen. I have done both soft reset and hard reset. Nothing works. The phone gets locked in the boot loader screen. Need help.
Thanks,
Julian
Try to reflash with Qtek ROM instead...
Why you said that it's locked on the Bootloader screen?
Is it frozen or locked?
Hi Rayan,
I tried flashing with the Qtek ROM. I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there. Nothing else happens. I have sent the device back to the guy from whom I bought it.
I got the same problem as Julian - I tried to upgrade with the mentioned ROM and now my device are stucked at the boot screen :?
Some help here ? I'm in same situation
I have an O2 with Dopod rom, after I instaled some software I must to restart and then my O2 are stucked/frozen on Windows Mobile splash screen
Only if I remove the battery I can stop the pda.
I can't do nothing to make him to start. Some ideea ?
:shock:
Later Edit :
solved with http://forum.xda-developers.com/viewtopic.php?t=49298&sid=35f5c1e9e165997b4634ea0c7700ac76
Same issue here with a O2 Xda Neo with German Rom.
Applied the procedure of the prophet wiki : How to CID unlock and Upgrade your Prophet (SPL 2.09 & 2.15)
After step 6 and a soft rest it is stuck in bootloader and will not do anything else, not even off or hard reset...battey has to be removed in order to shut it off....
Any ideas?
Remind me to find the guy who wrote the wiki page on unlocking CID in Prophet......good job pal......
Aaaaarggghhhh %^*^%*^%*^%*
Problem solved..
Hi everyone,
Good news at last. I sent my Qtek S200 to the guy from whom I bought the phone. He fixed it and now I am a happy man. You can check with him if everything else fails. Email him at E gadget Depot ( [email protected]).
All the best..
i tried to upgrade my QTEK S200 with this RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID.zip it got to 95% and then it gives me nbf file cannot work with your PDA. Please help.
I have this problem too, i know only one exit from this situation - i have flash my s200 with RUU_215737_2157135_023021_QTEK_s200_RUS ROM, now it work fine.
you find it her
bootloader issue
I have the same problem too, If anybody know method to fix this problem please help us.
I cannot active sync as it does not connect to the device. So I cannot flash. As soon as I powerup, I get the Qtek screen and then it goes to the bootloader screen and stays there.
THX in advance for you help
Robert
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Please, the links to the solution does not exists anymore.
I need help!!
Qtek S200 stuck in tri-color screen, all flashing so far still does not make it work..
When doing a hard reset I get format failed.
/Jonas
I have same problem!
Anyone can help?
TJSM said:
I have same problem!
Anyone can help?
Click to expand...
Click to collapse
Go to HMA4's upgrade guide or my thread in my signature...
same problem
i have exactly same problem and i couldnt solve it too.So can someone help us?
Please someone explain completely what should we do.
i can not active sync and waiting on the bootloader screen
bacardilima said:
have same prob but solved thanx to this post
http://forum.xda-developers.com/viewtopic.php?t=58892&highlight=boot
and remember First off all, to enter in Boot Loader Mode is:
Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.
Then upgrade using a ROM
Click to expand...
Click to collapse
daelee,
you can get normal state, follow the bolded attention at above quote.after entering the 3 colour screen connect USB and you can load the original WM5 ROM on your device. after that, upgrade to any wm6 by the rules and active sync.
the link is dead on that message..
i went to the that page and the link for solution is dead.
http://forum.xda-developers.com/showthread.php?t=376561
find out is there anything that can help!

Problems with rom update

Hi all
First of all sorry for my grammer, english in not my native language.
I've tried to update my O2 XDA Neo with SMART1 WM6 Rom, i've download the file and started the "UPGRADE_ROM.bat" after installation finished i notice an error click then hardreset the phone, for a second on the display apear the HTC logo, after that the QTec blue screen with the IPL 2.15.0001; SPL 2.20.0001; GSM 02.20.21; OS 10.1.0.811 and then nothing happens. I hardreset the phone several times but so far no good. I come up with idea to go to bootload (holding camera button and pressing reset) and try to reflash it but the update_rom.bat says "No Device Connected" from there i have no idea what to do. I'm with MS ActiveSync 4.5 please help me.
the same problem with me i tried several methods to fix this problem but unfortunetely couldn't find any solution to fix it finally took my phone to the technical service.If you have quarantie I recommend you to the same thing.But never say them that I tried to flash a new rom because this breaks the quarantie.Just say my phone doesn't start.Don't worry they can't understand that you 've tried to flash your O2
Ok, things you should *do* before upgrading to WM6
Make sure that you have AKU2.2 (for instance RUU_Prophet_220734_2207114_024721_NVID.exe) installed _BEFORE_ upgrading to either AKU 3.3 (aserg for example) or WM6. This is in any case true for G4, most probably this goes for G3 as well, but I cannot say this for sure, since I do not own one.
If you happen to get stuck at boot screen because update process failed, grab the rom above and run it with USB plugged in, this will 9/10 of all cases fix your device.
No, I do not have a link to this rom, try to look for it yourself.
For the rest, happy upgrading
rom flash
make sure you disable your antivirus softwear and your windows firewall don,t use any extended usb hubs and you have cid unlocked it make sure let it do a full flash dont do enything else with your pc when you flash your phone good luck i hope this was usefull

Orange SPV M600 (HTC Prophet) Stuck in Bootloader

Guys,
I wonder if you can help. I have trawled this and many other forums and found many people that are having problems with their HTC Prophet or variations of the same device.
I have the Orange SPV M600, it was in my pocket and when I took it out to turn it on, it was displaying the bootloader screen after seemingly soft resetting itself. It is displaying the tri-colour bootloader with the following IPL/SPL
- IPL 2.10.0001 - SPL 2.10.0001
I have tried the following things that I have found in the forums:
1. Taking the battery out for 10 minutes ~ Still the same.
2. Hard Reset ~ I get the "Press SEND button to factory restore" message
but nothing happens when I push the call button.
3. Reflashing the ROM ~ I am unable to do this. I only have Vista and
WMDC does not see the phone in bootloader mode.
Is the phone dead? If so how could this have happened?
If anyone could help I would be eternally greatful. Oh and to add another complication the phone is still CID Locked
Thanks in advance
Barry
well if you where is south africa i would of helped you im sure if you have it runing on xp it will work my jamin did the same and all i did was push the camera button and reseted it got into tri colour mode and reflashed it
sorry that i could not help you but like i said if you in SA we could of tried it on my mashine
Any progress ?
did you ever get this sorted out ? Surely all you're gonna need is a PC with XP and active sync....
If I was closer you could have sent the phone to me and I would have had a go at reflashing the rom, but I'm at the other end of the country....
Hello guy here is a solution to flash under vista i have too a orange m600 and it works fine
http://www.modaco.com/RUU-Vista-done-u-t252977.html
help stuck on the bootlader screen?
guyz i have a jamin.. my cousin was flashin it and flashed the wrong software.. if i reset the phone it shows the boat loader screen!! and i cnat do anythin..caz u tell me which slftware to flash..and how to do it?? My freind told me all solution to my problem's will be solved here
hopin i will get my solution
First of all, download the NVID (no vender) AKU2.2 from here. http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Then, open activesync, select connection settings and UNCHECK the connect through USB option.
Then run the NVID file. It will take a while, and may seem to get stuck at 80% or 95%. Just leave it alone.
When that's done, you can either use it as it is, or load anyother ROM you want.
i have a bit similar problem
can some one plese guide me how to flash it with xp?????
Regards
First get a version of ActiveSync, any will do, but more recent is probably better. Then download the ROM (see above). In ActiveSync>Connection Settings uncheck the Connect through USB option. Then connect the Prophet.
Next Unzip the NVID file, and run RUU_PROPHET... This will flash your Prophet with a very basic ROM. If you then want to upgrade to a different ROM follow these steps: http://forum.xda-developers.com/showthread.php?t=310452

No 3colourscren

my prophet was working normaly and while i was installing a program it stoped. i formated it and reinstalled the windows but what happened is:
1-it doesnt recognize the memory card anymore
I thought it is rom problem , i tried to install anothere rom but THERE IS NO 3 colour screen but the prophet is working
please any body have idea about this problem reply .
have u done hardspl? try flashing another rom..
i tried hardspl but it didnt continue the process
while i was doing hardspl my prophet turnedoff
thank blusilv for reply
where is the help??????????????
Listen up
First off all charge the battery for 2 hours before doing this.
After turn on the device and press for 5 seconds the com button on the left side of the device.
You will enter the 3 colours loader.
Connect the device to the PC.
Step 2 Install the original Rom
Step 3 Do a Rom update use step 2 of pdamobiz Rom, select update rom file and wait.
Step 4 Do a hardspl G3 or G4 see your device to see witch one is it.
Step 5 install a new Rom with the RUU update utility G3 or G4.
Then you just have to wait the device to reboot and you can use it.
Note: Use the 2.19 radio Rom its the most stable, you can install it after installing the final Rom ok.
Any questions feel free ok bye.
i am sorry but i thought the three colour screen meens bootloader my problem now that i cant change this rom as it dont recognize the memory and also there is prblems with bluetooth.
thanx deltav but ineed more help
Listen up that procedure i explained would put the PDA working 100%, if you have the problems you say you do, its because you installed a rom inappropriate for you device. The memory and bluetooth problems come from bad radio rom and from roms that are not suitable for the device, you mad bad installations, that is the real origin for your problems, if you want to stay with your device with problems fine, in my opinion the best is to put the original rom in and after that, do the rest of procedure if you don´t want to this its up to its your device not mine.
i tried what you said deltav but the problem is there is no 3 color screen and i tried almost all tools of ubgrading and downgrading but i cant remove this rom from my prophet my prophet is G3.
thanks for help but more please
Hello,
Same problem here, no 3-color screen appears when I start or reset and press the comm button on the side.
help for me and seichi please
OK guys after beeing in bootloader mode do a g3 or g4 update with a new rom don´t forget to connect the usb cable correctly, see if it works, if it does not tell me what are your problems, bye.
drdisho said:
i tried what you said deltav but the problem is there is no 3 color screen and i tried almost all tools of ubgrading and downgrading but i cant remove this rom from my prophet my prophet is G3.
thanks for help but more please
Click to expand...
Click to collapse
Listen did you charge the device for 4 hours first on the electricity - step 1
Do a hard reset with the stylus on the device - step 2
press the left com button for 5 seconds on the device, before anything appears on screen - step3
If everything goes well the 3 colour screen will appear.

PLEASE HELP! spv c600 stuck on 3 colour screen!!!

I tried upgrading to a wm6 rom without knwoing i had to app unlock and supercid my phone... now its stuck on the 3 colour screen!! what can i do???
Reinstall rom again.
Flash original ROM
Flash the original ROM first and then after unlocking your Tornado, flash any ROM you want to upgrade to.
Follow the excellent Kar Hoe's guide to upgrade your Tornado and you will be fine.
you cant flash original rom when its stuck in the colored screen
Yes you can
wel im trying for more then a week now, but no go, no matter what i do or try.
It stays in bootloader 3 colour screen
Original flash file = no go, cause it cant connect to activesync.
mtty = no go , USB port can not open no matter what version of mtty.
ttermpro = no go , can not open.
So if its possible, please tell me how.
muiz2 said:
wel im trying for more then a week now, but no go, no matter what i do or try.
It stays in bootloader 3 colour screen
Original flash file = no go, cause it cant connect to activesync.
mtty = no go , USB port can not open no matter what version of mtty.
ttermpro = no go , can not open.
So if its possible, please tell me how.
Click to expand...
Click to collapse
turn off the phone and redo the ttrermpro steps
When i put the battery in, the phone goes on automaticly.
And goes in 3 colour mode.
And from there nothing works
muiz2 said:
When i put the battery in, the phone goes on automaticly.
And goes in 3 colour mode.
And from there nothing works
Click to expand...
Click to collapse
cause you dont have a operating system so to say so its going to go into the bootloader. if you get to a bootloader than your phone is not "bricked" or broken, you just need to flash a rom onto it.
follow this guide exactly http://karhoe.net/guide-upgrading-htc-tornado-to-windows-mobile-6
i have read that many times, and tried over and over again.
But it wont flash, no matter what i try.
i give up
You should flash with factory wm5 original rom.
Can you please tell me where to get that?
Simple, just google for SPV C600 WM5 AKU2 ROM
http://www.google.com.my/search?q=S...s=org.mozilla:en-US:official&client=firefox-a
http://www.orange.co.uk/business/download/c600_aku2/c600_email.exe
Try this
http://www.orange.co.uk/business/download/c600_aku2/c600_email.exe
Try this
Simple, just google for SPV C600 WM5 AKU2 ROM
http://www.google.com.my/search?q=S...s=org.mozilla:en-US:official&client=firefox-a
Double Posting
Talk about double posting
Can you tell exactly what procedure you are following so that we can troubleshoot?

Categories

Resources