Related
Hi guys, first of all I just want to say thank you for this forum.. I ran into it a while back and was inspired to buy a kaiser just because of you guys. I have an iphone right now and I really want to replace it with something that has i don't know user accessible memory, MS office, GPS and the list goes on so I bout an At&t 8925, I got a good price on it and was very happy to finally able to get rid of the iphone
anyway I received the phone a few days ago and proceeded to do a sim unlock to use it with t-mobile after playing with it for a little while, I have already read the wiki, and lot of posts and searches..
I dnloaded this http://forum.xda-developers.com/showthread.php?t=375583 and plugged in the phone made sure activesynk connected and flollowed the instructions...
It went through the first step (hard spl) without a problem and I think the second step went well also. After that I begain the third step and the program froze, I waited for almost an hour just to be sure (windows also said it was 'not responding') I finally had no choice but to restart my computer, (its vista)
Anyway I pressed the power button on the phone and the phone acts like its booting up, I see the at&t screen, then it goes to the 3g screen and It just goes to a blank, black screen. I am still able to connect it to my computer and access the phone. I can access the 'boot loader' red blue green screen
I did a soft reset and tried to reload the unlocker porgram but nothing happens, I am stuck and I havent found out what to do through my searches can you guys help me out I am really new to this phone
I even took the time to downgrade my computer from vista to XP (finding all my drivers was a ***** since my computer was shipped with vista) but I found them one by one and still no luck loading the unlocker
one thing I did notice was that the bootloader screen now says "security unlocked" on top, not sure if It did that before
Thanks for all the help
Thanks
all you have to do to fix your phone is flash a new rom onto it. just open the boot loader and run the ruu and it should fix the problem
that's because you need to install a wm6.1 rom on your phone to use this unlocker. you would have found the answer if you read the thread
Olipro said:
hence why I wrote a message box on Step 2 stating "you may need to upgrade your phone to WM6.1"
****ing idiots.
Click to expand...
Click to collapse
oh **** how did i miss that... going to try another rom, i'll let you guys know how it goes
thanks
tman6919 said:
oh **** how did i miss that... going to try another rom, i'll let you guys know how it goes
thanks
Click to expand...
Click to collapse
Thread done. Please remember to read through all instructions etc...
I know, I know, there are loads of threads like this but I must be lacking something in the brains department as I've spent the last 6 days (since I got my orange tytn) reading this forum trying to understand how to unlock the thing without turning it into a brick and then to flash a rom and radio.
Everything I read on here has people contradicting other people and I end up not having a clue what to do in the end.
HEELLLLP!!!
To confuse matters even more I thought I'd got it sussed and then read about roms having/not having a CUBE!!!! WTF???? I then gave up and started typing this thread...
Here's what I think......and PLEASE correct me or agree with me....
Firstly I seem to be stumbling at the first hurdle since I have an orange tytn and that it seems is the worse to have for some reason???
I thought I'd start off simply by using the kaiser simunlocker to unlock the phone (by jocky) but then came across something called hardspl with all its variances, so OK lets go with the flow and dismiss the hardspl step for now assuming I can do it and read on...
Assuming I could ever find a program that makes a backup of the rom I've got I'd carry on with the unlocker until I get to the step (step 10) that says download the original radio..............this of course doesn't exist (1.27.14.32) so I look for a proggy that downloads the radio to use at this point. Here's where I come unstuck again.........no proggy!!
At this point I must assume that this may not be possible on the model I've got if I want to be sure I can make it original again.
Could someone please confirm this so I can accept the fact that I have to use what came with the phone and save myself a few hours a night getting nowhere...
Sorry for my rant but I'm frustrated that my old brain can't figure this out and giving up seems to be the only option. I completely understand that I'll get flamed for this since I'm a noobie and asking again what numerous otheres have asked but I accept that...
I have great respect for all you guys that can actually understand this on first reading and especially the people who produce this stuff....
Thanks again folks
familyguy said:
I know, I know, there are loads of threads like this but I must be lacking something in the brains department as I've spent the last 6 days (since I got my orange tytn) reading this forum trying to understand how to unlock the thing without turning it into a brick and then to flash a rom and radio.
Everything I read on here has people contradicting other people and I end up not having a clue what to do in the end.
HEELLLLP!!!
To confuse matters even more I thought I'd got it sussed and then read about roms having/not having a CUBE!!!! WTF???? I then gave up and started typing this thread...
Here's what I think......and PLEASE correct me or agree with me....
Firstly I seem to be stumbling at the first hurdle since I have an orange tytn and that it seems is the worse to have for some reason???
I thought I'd start off simply by using the kaiser simunlocker to unlock the phone (by jocky) but then came across something called hardspl with all its variances, so OK lets go with the flow and dismiss the hardspl step for now assuming I can do it and read on...
Assuming I could ever find a program that makes a backup of the rom I've got I'd carry on with the unlocker until I get to the step (step 10) that says download the original radio..............this of course doesn't exist (1.27.14.32) so I look for a proggy that downloads the radio to use at this point. Here's where I come unstuck again.........no proggy!!
At this point I must assume that this may not be possible on the model I've got if I want to be sure I can make it original again.
Could someone please confirm this so I can accept the fact that I have to use what came with the phone and save myself a few hours a night getting nowhere...
Sorry for my rant but I'm frustrated that my old brain can't figure this out and giving up seems to be the only option. I completely understand that I'll get flamed for this since I'm a noobie and asking again what numerous otheres have asked but I accept that...
I have great respect for all you guys that can actually understand this on first reading and especially the people who produce this stuff....
Thanks again folks
Click to expand...
Click to collapse
Screw what everyone tells you and start with the link above this thread. Actually the second thread on this page. I think I am one of the oldest around here so its not your "old" brain. _Alex_ has gone to great length to get all of the information you need in one place. Start with his sticky. Good luck.
hello, lots of stuff to learn, first thing, which sounds like you did is read, next hard SPL
see the 2nd sticky in the forum,
go down to kaiser wiki, then rom tools wiki, the 3rd choice, hard SPL cid unlock, read carefully and install, once completed, now your phone is ready to flash roms, (for Kaiser) most come with radio or recommend radios to use and not use. if you have problems with hard spl then use the wiki again to troubleshoot and the first 2 stickys
im out
just sell your kaiser and stick to a razor......lol.....j/k....just listen to p1tater...hes right!!
Hey family guy,
A few months back I got an Orange TYTN II just like you. I read for about a week on here untill I felt confident enough in the steps needed to flash a new ROM. First off I Hard SPL and then went for Dutty V3 ROM which was perfect untill I then felt clever enough to flash a new ROM a few weeks later. Due to not sim unlocking correctly the first time around, upon a new radio being flashed to the phone It locked my SIM.. untill I found out the true way to SIM unlock the phone.
Once you have Hard Spl and SIM unlocked you are well away. I know at this point you are probably feeling pretty confused with all this but believe me it is well worth it in the end.
Oh and FYI.... I can confirm that there is an Orange original Rom on here and a few compatible radios should you ever need to revert back to them for some reason as I had to do this myself at one point when trying to work out where I was having issues with something.
All the best
Chris
P.s are we going to start the "who is the oldest contest yet?"
c.b said:
P.s are we going to start the "who is the oldest contest yet?"
Click to expand...
Click to collapse
There's been one around for a while:
http://forum.xda-developers.com/showthread.php?t=325426
but then they do say that memory's the first thing to go, so I'll forgive you!
Confused Stu said:
There's been one around for a while:
http://forum.xda-developers.com/showthread.php?t=325426
but then they do say that memory's the first thing to go, so I'll forgive you!
Click to expand...
Click to collapse
PMSL....That's where it went, I knew I had left it somewhere. Now where are my damn glasses I can't read a thing.
Unlock your Orange Kaiser
Here's my experience ..
1. Basically HardSPL your Tytn II to facilitate a cooked ROM that can be 'sim unlocked'
2. Install the Cooked Rom
3. Run the Sim unlock generator code
4. Phone is *UNLOCKED !*
5. Install a ROM of your choice
6. Install a Radio of your choice
Here's the stuff I used:
READ ALL THE POSTS - READ ALL THE POSTS !!
** USE WINDOWS XP OS with Activesync!! **
1. HTC Kaiser Hard-SPL v1 - CID Unlock & Flash any ROM to your device
You will know you got it right when it says either 1.0.HardSPL or 1.0.OliPof.
NOTE: I had problems here and had to force it with JumpSPL1.93 because HardSPL would not install.
2+3. I used Jockyw2001 Kaiser Sim Unlocker v0.1
NOTE:
> The file has three steps ... 1, 2 & 3 so you can't go wrong:
> Step 1. Installs the 'patched' Radio
> Step 2. Generates the key code for unlocking (on your PC) which you enter into the Tytn.
> Step 3. Installs a replacement radio
4. My code was a series of numbers that I had to type into the screen.
5+6. Read my signature for what I'm using today (it changes)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
All instructions are on screen with prompts.
I sweated for days before I chanced it and it took me about 15 minutes from start to finish but you end up with a pucka HTC looking Tytn II and not the Orange variant.
A few important pointers from the bit I learned:
1. You cannot do this on a WM6.1 Tytn II, you have to go down to WM6.0 - As mine was WM6.0 it didn't matter.
2. Vista is a ***** for doing this and you have enough things to think about without the PC's OS .. USE XP !!
3. HardSPL once done, the Tytn II is clear for all future ROM + Radio upgrades.
4. Bootloader = Power button + Camera button + Reset with stylus
5. Hard reset is Left softkey + Right softkey + Reset with stylus
6. Always Hard reset after blowing any new ROM before using.
7. Backup all your contacts etc. to your SD card with PIM Backup 2.8 before you do anything.
8. Remove the SD card before you begin.
9. The 'Cube' isn't always included in the ROM's - I use this CUBE
10. Most Roms come with their own 'loader' called 'Kaiser_RUU' so you don't have too much to think about.
11. Stick your Radio and ROM information in your signature, you never know when you may want to go back and forget what you had installed ;-)
12. Installing a new radio on a phone that isn't SIM Unlocked will result in a LOCKED TO ALL NETWORKS phone - So SIM Unlock it !!
Enjoy
PS. Let me know if you can't find the files you need.
SIM Unlocker Software HERE
PPS. Before you unlock your Orange can you pop over to this thread and answer Rabdo's question - Thanks.
ajs007 said:
Here's my experience ..
12. Installing a new radio on a phone that isn't SIM Unlocked will result in a LOCKED TO ALL NETWORKS phone - So SIM Unlock it !!
this thread and answer Rabdo's question - Thanks.
Click to expand...
Click to collapse
Hey I have a question about this point - I've never SIM unlocked my phone and have flashed about 6 ROMS, and various radios and never had a problem. All I did was run hardSpl, then started flashing.
So what I'm asking is are you sure of this point?
Mods Please Close
This is a useless thread. Mods please close this thread.
P1Tater said:
Screw what everyone tells you and start with the link above this thread. Actually the second thread on this page. I think I am one of the oldest around here so its not your "old" brain. _Alex_ has gone to great length to get all of the information you need in one place. Start with his sticky. Good luck.
Click to expand...
Click to collapse
Oldest around here your a Matt Serra fan I swore you were like 25.
-McMex
mattarse said:
Hey I have a question about this point - I've never SIM unlocked my phone and have flashed about 6 ROMS, and various radios and never had a problem. All I did was run hardSpl, then started flashing.
So what I'm asking is are you sure of this point?
Click to expand...
Click to collapse
I have heard before that Orange Kaiser's are a little different to other networks and need to be SIM-unlocked before they can use a different network.
Confused Stu said:
I have heard before that Orange Kaiser's are a little different to other networks and need to be SIM-unlocked before they can use a different network.
Click to expand...
Click to collapse
Ok thanks, that would make sense then.
Cheers!
Hi all and thanks for your comments advice and encouragement..........just quickly looking at the old age thread I am one of the oldest at 47!!
The thing about this thread is that it's happened again and there are only 13 posts!!
There's been contradiction about the orange tytn above. Some peeps say it needs to be unlocked (and that they've done it but don't mention what radio they're using), and some peeps say it doesn't need to be unlocked!?!?!?
There is my confusion and my hesitation to do anything in case I lock the sim out completely. That I can't have as I need the phone at all times to get in toch with my kids (humans or small goats depending on what your state of mind is!).
Here is what I think I should do...
1.) Use hardspl to unlock something (not sure what at the mo) so that I am able to flash
2.) Unlock the SIM lock using kaiser sim unlocker (or not! jury is out, but not sure which radio to use so scared of brickifying it)
3.) Flash my choice of rom (but not sure if I have to then flash a radio or if the radio is included in the rom)
That's about all my poor tired OLD.......VERY OLD brains can figure out and there are enough 'I don't knows' there to stop me in my tracks...
I'll keep reading though but in the meantime I could do with gleaning info from someone who is in the UK on orange and maybe has a recent model...
TTFN
familyguy said:
I'll keep reading though but in the meantime I could do with gleaning info from someone who is in the UK on orange and maybe has a recent model...
TTFN
Click to expand...
Click to collapse
I'll be 48 in August, so it's not just the Youngsters who play with the 'phones.
(Does that make me the oldest ?)
I bought the TytnII from the Orange Shop in Leicester just before Christmas but didn't have the bottle to unlock it for months ... Main reason was the unlocking 4 months ago was £20 !! and i didn't want to brick it either.
I spotted someone selling the unlocking service on ebay about a month ago, so I knew someone had cracked it here (and some cheapskate was selling the service.)
Feel free to private message me, if you need to we can talk it through over the phone.
Alan.
familyguy said:
There's been contradiction about the orange tytn above. Some peeps say it needs to be unlocked (and that they've done it but don't mention what radio they're using), and some peeps say it doesn't need to be unlocked!?!?!?
TTFN
Click to expand...
Click to collapse
I may have added to the confusion - I do not have an Orange phone, adn was questioning whether you need to SIM unlock the phone b/c I hadn't. Later it was pointed out that Orange phones may be different and need to be.
mattarse
Greetings to all...........and a damn good weekend to everyone!!
mattarse you simply added to the confusion in my mind............for other it was probably very clear
ajs007, I will PM you and perhaps a quick chat to get me up and running would be great!
One thing I do know though..........when (yes, I've gone from if to when) I get more knowledable about this I'll be one of the first peeps there to help anyone out if I can!
After a long chat with ajs007 (for which I am very grateful) I felt I had the confidence to go ahead and install hardspl using the jumpspl route.
My tale of woe follows as it was unsuccessful every time...
I followed jockys instructions,
1a. download the 5 attached files
1b. connect your PC to phone with a USB cable
2. REMOVE SIM and SD CARDS !!
3. copy JumpSPL1.56-KAIS.exe to your device and run it (make sure the USB cable is still connected). If you still get a white screen then reset your device and now try JumpSPL1.93-KAIS.exe
4. after a few seconds "USB" appears on the phone display
5. unplug and replug the usb cable
6. deselect "Allow USB connections" in Activesync connection settings
7. now flash hardSPL (run KaiserCustomRUU.exe from flash-hardSPL.zip on your PC)
After step 3 (for both 1.56 & 1.93) I get the tri-colour screen (not mentioned above) shortly followed by 'USB' on the white at the bottom (step 4).
(I guess this makes it a quad colour screen instead of
I then did step 5 and step 6 as above and moved on to step 7 to run kaisercustomruu.exe.
I then get a screen which says verifying phone settings and a further screen which has 'current info about your pda phone:' and lists nothing!!
Another line that says 'image version:' and has nothing listed and yet another line that says 'select from below:' and has nothing next to it!?!?!?!?
There is a button that says update the current ROM version but I dare not press it if it is going to update with nothing!!!??
On top of all that I read contradiction again where the instructions above state that you must deselect 'allow usb connections' yet when you run kaisercustomruu.exe it states that you must have an activesync connection....
I'm now really confused and convinced it just isn't to be. Sorry Alan it did sound so easy when you explained it but there must be something different about my phone.........I'm going to throw myself or the phone or both of us off a tall building.............now Im totally depressed
Exit stage left feeling very sorry for oneself...
Looks like everything was A.O.K. for flashing..
IMPORTANT ** You didn't say if you had SPL xxx PoF on the Tri Screen ?
I didn't have any reference to a ROM on the install screen but it worked, probably because the ROM was in the same directory and it didn't need to look anywhere ....
I think (but I'm not 100%) the activesync USB connection is an XP v. Vista thing, and you do need USB connection in XP.
In summary, if you did have SPL xxx PoF on the Tri Screen you should be good to go.
From totally & utterly confused to successfully running Dutty's 6.1!!
Lots of bonus points and many thanks to AJS007 for allowing me to bother him with all my questions and lack of confidence.
Here's my tale...
Firstly I tried to install hardspl running from my PC and a USB cable but I got the infamous white screen!
I then followed the instructions for using jumpspl version 1.53 (for some reason the instructions I read didn't say remove and re-inset battery therefore I didn't do that bit!).
I got to the bit where 'USB' appears on the screen and pulled out the cable then re-inserted it. I have no idea why you do this but I did it. When I pulled the cable out the screen had 'Serial' on it and when I re-inserted it, it went back to 'USB'
I carried on to the next step and unchecked the 'Allow USB Connections' in Activesync (again I have no idea why you do this) and went on to run 'kaisercustomruu.exe'
Here's where I hesitated and got stuck. The program started on the PC and got to a point where it interrogated the phone, shortly after that I was presented with another screen that waited for my input ready to 'Update' but I hesitated since there was no information listed under 'Image Version:' and 'Select from below:'.
I wasn't sure what to do here and cancelled the whole thing in case I bricked it
After further investigation, more reading and speaking once again to my mentor AJS007, I decided to go ahead and throw what caution I had left to the wind, so I pressed the 'Update' button.
After a few more screens I got to the point of no return and gritted my teeth.........nothing happened........I disconnected and re-connected and tried again..........nothing again............after a third time though (and I don't know why) it burst into life and I got the 'percentage screen'.
At this point I did think I had trashed it but plodded on regardless in the hope that I hadn't and everything would be OK. Thankfully it was and on entering the bootloader screen I saw 'olipof'..............all was well
This gave me the extra bit of confidence I needed to go through the unlock procedure and then on to flash Dutty's latest. I did get to the point where I had to enter the unlock code and it took 2 attempts to accept it for some reason........I can't explain that either!!
It was all in all a stressful time and involved a lot of pacing up and down when the ROM was flashing, taking what seemed to be hours to complete and slowing down to an almost stop at certain points, but in the end it did all work and I am now left with a transformed T2, but with the following little problems,
1.) My bluetooth headset has to be paired every time I want to use it!
2.) When I go to re-calibrate the screen (with the cross hair) it freezes up and I have to do a soft reset.
3.) My screen 'tap' noises have disappeared (except when I press the 'start' button)
I haven't tried to reflash the radio to see if that will take care of the bluetooth issue yet but I intend to do so in the next few days.
For anyone that's interested I'm using the radio ROM that was included in Dutty's latest build (WM6.1_5.2.19209) which is 1.58.16.27.
Finally, once again my thanks to AJS007 who went to the trouble of helping me in my few hours of need.
If anyone new here would like to ask me any questions about my noobie experience please don't hold back!!
I was trying to load wm6.5 and I must have missed a step or loaded bad rom. I unlocked it, at least i think i did. When I load the boot screen (volume down and power) it says "security unlocked".
When I start the phone, it says "Touch Pro" like usuall and then crashes, vibrates and restarts.
I used the search function on this forum to find a similar problem but I could not understand the solutions. Any help would be great, since I have NO phone.
Ya know, if you want help, you could post some basic info. As is, your post is as useless as your phone.
Exact device?
Carrier?
SPL?
Previous ROM?
ROM that bricked your phone?
Previous flashes? Radio?
OK,
Touch Pro - Sprint
All the other info I know is that before this it was running stock rom. And all the info I can get now is off the bootloader screen. It says...
"
Security unlocked
RAPH800
SPL-0.37.CMONEX
MixeoP-Hermann (LED) v0C85
MicroP-Hermann (KEY) v0685
PSOC-Raph STAGE_EVT v20
"
You have a CDMA phone, and you have tried to flash GSM ROM. That is the best way to kill your phone. ROMs that you want are in this section: http://forum.xda-developers.com/forumdisplay.php?f=465.
Well that would explain the problem. But everytime I go to install new ROM it starts the process then goes from 0% TO 100% in less than 30 sec. It says its complete and there is still no change.
It's time for Mr. Herman to meet Mr. Microwave.
absolutely brick... never flash GSM ROM in CDMA...
gld_krieg said:
absolutely brick... never flash GSM ROM in CDMA...
Click to expand...
Click to collapse
Farmer Ted said:
It's time for Mr. Herman to meet Mr. Microwave.
Click to expand...
Click to collapse
Really guys, because after hours of messing around with it I fixed it. Fricken Senior and Junior members acting like they know it all, got bested by a noob. bunch of douche bags
so how did u fix it?
touch pro symbol then crash
I had the same problem if you turn the phone off hold the volume down and the power buttom together this will turn your phone on and place it in boot loader mode
Now use a differnt Rom to flash on the phone and it should work as long as the new rom is the correct rom for your phone (GSM, CDMA)
i had a sprint CDMA and i used the energy rom from oct 25 which crashed my phone then mighty rom brought it back to life so try that and see if it works
Floods7 said:
Really guys, because after hours of messing around with it I fixed it. Fricken Senior and Junior members acting like they know it all, got bested by a noob. bunch of douche bags
Click to expand...
Click to collapse
hey watch what your saying in the forums, theyre only suggesting and teaching u some moral lessons
Ted is just suggesting u something thatll get u a refurb or possibly(if your lucky) a new TP
and Krieg is just telling you that, soo the next time it wont happen again
good for you for fixing ur TP, consider yourself lucky, but maybe next time be more grateful that theyre telling u stuff that you DONT know and that will help u in the long run instead of calling them douche bags, theyre more experienced than you, not saying ur dumb but name calling makes you look immature
i suggest u reading this before you go any further
http://forum.xda-developers.com/showthread.php?t=508084
Sorry for double post
I think i bricked theHTC fuze that i bought yesterday I tried to do the Hard SPL but i was getting an error message, error 244 invalid model ID so i used a program to change the .nbh (a radio file) file so it bypassed the error message (by changing DIAM***** to RAPH*****, since my phone is raphael). I even got a message that the process was successfully finished but it turned out not to be true because the screen went black and now i cant turn it on, and i cant even get it into the bootloader mode. If i could at least get it into to tricolor screen i would be able to flash back the original radio and that would solve the problem because ive already done it a few times. Please let me know if there is a chance to get it fixed, even i had to send it to a professional but as long as it could be fixed, im really desperate. Thank you
brick, htc fuze, diamond, raphael, hardspl
You only get that error when your trying to flash the wrong device... Did you use the file "Raphael_CDMA_HSPL_037.zip" to unlock..?? Sound's to me like you used the Diamond Unlocker... Shouldn't be that hard to fix, hold the volume down button, power button, and insert stylus into the hole on the bottom to soft reset to try and open up BL screen... LMK if that works...
Why didn't you just follow the instructions for flashing? You aren't even security unlocked, so why were you trying to flash a diamond radio? That makes no sense at all. Also, if you are security unlocked, you need to get diamond radios from the raphael forum, because they're patched to flash onto raphaels. It sounds like you got yours from the diamond forum, which is the wrong way to go (especially if it's a cdma radio-that would kill your phone for sure). Did hard spl work? If not, why on earth did you forge ahead? YOU CAN'T DO ANYTHING UNTIL YOU FLASH HARD SPL!!!!!
Try pulling the battery for a while, the see if it will start up. It's hard to tell what you did, but since you went down such a wrong path, I wouldn't be surprised if the phone is a giant brick.
komar808 said:
by changing DIAM***** to RAPH*****
Click to expand...
Click to collapse
this should've been clue #1. If you have to change it because of the device ID, it's the wrong thing to flash. The Diamond and Raph look alike on the front, but are almost totally incompatible ROM-wise.,
I even got a message that the process was successfully finished but it turned out not to be true because the screen went black and now i cant turn it on
Click to expand...
Click to collapse
You are wrong there, it did flash successfully. The tools worked EXACTLY as they were designed. It's not the tools fault
Please let me know if there is a chance to get it fixed, even i had to send it to a professional but as long as it could be fixed, im really desperate. Thank you
Click to expand...
Click to collapse
You might contact olipro, I hear he's got the "magic touch" with devices. No guarantees. I've heard that it's almost impossible to unbrick a device like this after an incorrect/bad radio flash.
I really hope it works out for you. Read dude, the stickies are everywhere for your benefit. Best of luck to you.
brick, htc fuze, diamond, raphael, hardspl
I run into things like this DAILY. Been a service rep for over 30 years. If people would ONLY follow the instructions, I'd have less follow up work to do.
Unfortunately they make these phones too easy to hack (good for us) but sometimes noobs make it hard for the rest of us.
lol
This is what happens when you don't follow directions, don't read enough, and are monkeying with things you obviously shouldn't be monkeying with.
When you got the device ID error, you should have stopped right there and thought "gee, maybe I should go over these instructions again and see what I did wrong" instead of trying to force a radio that will never work on your device.
Hope you can get it in to bootloader, otherwise enjoy your shiny new brick.
Well, hope you get it solved and otherwise you learned a lesson in a very expensive way I'm afraid...
Farmer Ted said:
Why didn't you just follow the instructions for flashing? You aren't even security unlocked, so why were you trying to flash a diamond radio? That makes no sense at all. Also, if you are security unlocked, you need to get diamond radios from the raphael forum, because they're patched to flash onto raphaels. It sounds like you got yours from the diamond forum, which is the wrong way to go (especially if it's a cdma radio-that would kill your phone for sure). Did hard spl work? If not, why on earth did you forge ahead? YOU CAN'T DO ANYTHING UNTIL YOU FLASH HARD SPL!!!!!
Try pulling the battery for a while, the see if it will start up. It's hard to tell what you did, but since you went down such a wrong path, I wouldn't be surprised if the phone is a giant brick.
Click to expand...
Click to collapse
I did hard SPL first with 1.90OliNex (because the one that was in the unlocking package originally didnt work beacuse of the invalid model ID message) and i thought thats what security unlocked the phone and then i tried to put a costume radio that would allow me to unlock the phone but the radio wouldnt flash. So i went back to the SPL from the unlocking package (HARD SPL 1.34) and i changed the .nbh file from DIAM***** to RAPH***** and then it bricked... The reason i did this is beacuse of the following link :
http://forum.xda-developers.com/archive/index.php/t-427305.html
I just hope something can still be done otherwise this is just a good warning for all others not to do this. Thank you for the replies
jdmsohc22 said:
You only get that error when your trying to flash the wrong device... Did you use the file "Raphael_CDMA_HSPL_037.zip" to unlock..?? Sound's to me like you used the Diamond Unlocker... Shouldn't be that hard to fix, hold the volume down button, power button, and insert stylus into the hole on the bottom to soft reset to try and open up BL screen... LMK if that works...
Click to expand...
Click to collapse
No I used a gsm unlocker, HARD SPL 1.34... There is a more detailed explanation in the post above
Hard spl 1.34 is either cdma or diamond gsm-I don't know which. I do know that it will brick a gsm touch pro. Flashing the wrong hard spl is the guaranteed way to kill a phone. If you actually flashed it, the phone is dead. Try pulling the battery for a day.
You need to run the gsm raphael unlocker to security unlock your phone. You need to pay for it, too. Hard spl doesn't security unlock your phone-it only CID unlocks it.
Farmer Ted said:
Hard spl 1.34 is either cdma or diamond gsm-I don't know which. I do know that it will brick a gsm touch pro. Flashing the wrong hard spl is the guaranteed way to kill a phone. If you actually flashed it, the phone is dead. Try pulling the battery for a day.
You need to run the gsm raphael unlocker to security unlock your phone. You need to pay for it, too. Hard spl doesn't security unlock your phone-it only CID unlocks it.
Click to expand...
Click to collapse
I used the GSM one. Ok i just pulled out the battery and hopefully the phone allows to get it into the bootloader...
Worst case scenario, smash it and pay $100 for ur insured replacement... That is, if you have insurance...
jdmsohc22 said:
Worst case scenario, smash it and pay $100 for ur insured replacement... That is, if you have insurance...
Click to expand...
Click to collapse
Hahahaha !
Good one !
But dude no offense but u deserve a black shiny 600$ brick because YOU DIDN'T FOLLOW THE INSTRUCTIONS ! THEY ARE THERE TO BE FOLLOWED UNLESS AND UNTIL YOU ARE SO RICH THAT YOU CAN WASTE 600$ OR YOU ARE A SUPER CHEF AT XDA AND ARE SURE OF WHAT YOU ARE DOING !
Anyways Best of luck hope you can unbrick it !
otherwise smash it
Bye.
LoL yeah a $600 paper weight may also come in handy..?? Or like previously stated, take your anger out on it for not doing it right the first time lol...
I now this might be a little too late to answer,but i want to give my two cents to this brick posts. Maybe someone will need it. This is for anyone that might be where I was for over 2 weeks. I though my Fuze/ Raphael / touch pro was history. My phone will get into restart loops when ever he wanted. It was very anoying. After replacing every possible software from Radio, Hard Spl, different rooms and even start up splashes, and almost getting "ORD" in the process. I finally took my phone apart, since there was no warranty. Once open I saw that the reset bottom inside was too close to the rubber reset bottom from outside. Guess what ?? That as all it was..... Good luck to all. : )
So is there anything i can do? i cant turn the phone on but windows sees the device just cant add a driver to it.... any help please?
Have you tried flash HSPL of TP2 on top of it?
yes but windows isnt recognizing the device so the hspl for tp2 wont work cuz it says that its not connected
not even if you put it in bootloader mode?
i cant get the phone to turn on in any mode.
notanerd1411 said:
i cant get the phone to turn on in any mode.
Click to expand...
Click to collapse
Ouch...you just spooked me out of unlocking/flashing my TP2 for another few weeks.
Wish I could help you out...sorry
Send us a screenshot of what do u see when you turn on the phone, is it it three color?
AstronusX said:
Send us a screenshot of what do u see when you turn on the phone, is it it three color?
Click to expand...
Click to collapse
Agreed - i've 'bricked' my tp1 several times, and forced the reflash from hardspl on, successfully from the bootloader screen, instructions to get there are all over.... Thinking positive here
notanerd1411 said:
i cant get the phone to turn on in any mode.
Click to expand...
Click to collapse
Sorry dude yea I was in the same boat as you,,,2 days ago bad news its officially bricked...I flashed mine tp2 also with the tp1 hardspl
I know u cant turn it on,,when u plug it in sometimes u get the battery charger light to come on...and thats about it...You cant bootloader it...and you cant turn tp2 on.
Luckly I had the insurance and got a new tp2 the next day..learn from your mistakes man, its beyond bricked....buying a new phone only option or insurance way
codom2000 said:
Sorry dude yea I was in the same boat as you,,,2 days ago bad news its officially bricked...I flashed mine tp2 also with the tp1 hardspl
I know u cant turn it on,,when u plug it in sometimes u get the battery charger light to come on...and thats about it...You cant bootloader it...and you cant turn tp2 on.
Luckly I had the insurance and got a new tp2 the next day..learn from your mistakes man, its beyond bricked....buying a new phone only option or insurance way
Click to expand...
Click to collapse
i had the same problem with my tp1 - forced to boot loader, and just forced the flash even though the screen was blank. I AM NOT SUGGESTING YOU DO THIS. But on that particular model on its OWN roms it worked for me ^^
[edit]
very scary process hehe
starscalling said:
i had the same problem with my tp1 - forced to boot loader, and just forced the flash even though the screen was blank. I AM NOT SUGGESTING YOU DO THIS. But on that particular model on its OWN roms it worked for me ^^
[edit]
very scary process hehe
Click to expand...
Click to collapse
How did you do it?
Thanks for the help all. But i could not even get the little led to come on. I imagine the device was on seeing as windows knew something was there however it could not find a driver. So i called Verizon and have them shipping me a new one.
if windows sees it, you might be able to reinstall stock rom.. windows wont even see mine
yznhmr said:
if windows sees it, you might be able to reinstall stock rom.. windows wont even see mine
Click to expand...
Click to collapse
I dont think so, I think you have to have a bootloader waiting for the rom.
other option would be JTAG it, i dont think anybody has done it so far, you need a hardware guy to figure out where the jtag points are on the phone board for that.
a1jatt said:
I dont think so, I think you have to have a bootloader waiting for the rom.
other option would be JTAG it, i dont think anybody has done it so far, you need a hardware guy to figure out where the jtag points are on the phone board for that.
Click to expand...
Click to collapse
whats a "JTAG"
yznhmr said:
whats a "JTAG"
Click to expand...
Click to collapse
your going to need some google for that - try googleguide.com
i am having a similar problem the phone does not turn on at all but when i plug it into my computer i hear a sound that a new device has been plugged in, however my computer does not recognize it as a touch pro2 is there any way to fix it?
rk73 said:
starscalling said:
codom2000 said:
notanerd1411 said:
i cant get the phone to turn on in any mode.
Click to expand...
Click to collapse
Sorry dude yea I was in the same boat as you,,,2 days ago bad news its officially bricked...I flashed mine tp2 also with the tp1 hardspl
I know u cant turn it on,,when u plug it in sometimes u get the battery charger light to come on...and thats about it...You cant bootloader it...and you cant turn tp2 on.
Luckly I had the insurance and got a new tp2 the next day..learn from your mistakes man, its beyond bricked....buying a new phone only option or insurance way
Click to expand...
Click to collapse
i had the same problem with my tp1 - forced to boot loader, and just forced the flash even though the screen was blank. I AM NOT SUGGESTING YOU DO THIS. But on that particular model on its OWN roms it worked for me ^^
[edit]
very scary process hehe
Click to expand...
Click to collapse
How did you do it?
Click to expand...
Click to collapse
heh i literally described it.
I just took the battery out, to make sure it was powered down. did the keys for boot loader, and just trusted it would make the connection.
had to try a few times, and its been a while since i did it - but as i recall i told the bastard flash on the computer and walked away, and the next time i got bootloader, so i turned it off and let it charge, then back to bootloader and flash and i was fine.
now for me i had flashed a gsm on cdma iirc and ive no idea why the above worked at all. Likely the flash was corrupted on the way in or something, but its been so long there's no way to remember enough details to see if its even something that's been observed in that state and sequence of events.
Code:
and for you lazy ppl - this board doesnt do multiquoting correctly, as they went lateral [more in a chain - good] but left out depth [how many sam quoted lucy quoted billy levels can we get]
so if your curious here's something for how to manually multiquote:
when your the third in the chain, you have to go to the quoted post and push quote copy and paste that. then go to the post you WANTED to quote, and right where the writing starts paste away:
[ QUOTE=rk73;4859704 ] [ QUOTE=starscalling;4856587 ]inner[ / QUOTE ]
outer [ / QUOTE ]
you
starscalling said:
your going to need some google for that - try googleguide.com
Click to expand...
Click to collapse
what a vague topic.. i saw like millions of things "JTAG"
any ways i called Sprint, and they are sending me a new one(refurb) It will be here on wed or thurs..
yznhmr said:
what a vague topic.. i saw like millions of things "JTAG"
any ways i called Sprint, and they are sending me a new one(refurb) It will be here on wed or thurs..
Click to expand...
Click to collapse
http://lmgtfy.com/?q=JTAG+cell+phone
[edit]
look its how you directly interface with the system board and components...