Can someone please help.
Recently I installed WM6 on my palm treo 750 and after a lot of trial and errors with various applications (each fail install resulting in a hard reset - mainly WM Live and Skype to get it to work properly. Everything worked great for about a week and yesterday everything ran really slowly, even after a hard reset.
I decide to reinstall the ROM from the memory card and that's where it's broken.
I would get the screen up as follows:
00018002
CHEEIMG.nbh - loaded
SPLASH1 - OK
bOOTLOADER - OK
GSM -
MICROP -
EXTROM -
OS -
and the progress bar only moves to about 1/20th along and stays there permanently (I left it over night last night)
I now can't get it to load at all and if I take out the memory card, it stays on the red/green/blue screen with "serial" at the bottom
Any help would be much appreciated
Fixed
The above problem fixed itself but the other day I dropped the phone again and now it's stuck back in the above post position.
I've tried using the palm recovery tool but with no luck.
Any help please :-(
broken again
The above problem fixed itself but the other day I dropped the phone again and now it's stuck back in the above post position.
I've tried using the palm recovery tool but with no luck.
Any help please :-(
solution???
did you get your fone fix again?? same problem happened here but it never worked for me!!!! maybe you might help!!
Try installing the 223 ROW from the EXE with the suggested mods to the XML config file. It may be something with your SD card.
Related
Hi - Okay, having installed active sync 4.1 I ran the ROM updater (JAMin_WWE_213923_2139123_022021_shi).. at 95% the PC crashed. This has left the phone in a complete mess. All I have is a screen with a red, green and blue horizontal bands.
On the screen it says RUU - IPL 1.00 - SPL2.13
I can't seem to reset the phone.
Can anyone help me sort this out?
Many thanks in advance.
Russell
UPdate problem fixed
Hi
Turned out that the screen described was the bootloader screen (I think).
I had to resart the PC to get rid of any open connections (error 260) and then run the ROM again. This connected and updated the phone despite the fact that active sync couldn't see the phone..
Phew, been a long day!!
Cheers Russell
Press reset button+camera button bootloader mode after load this rom
RUU_Prophet_220734_2207114_024721_NVID and enjoy it...
I've got a 2x T-mobile Vario here, i've flashed the first one to XMr6r3 this went fine. The other one stops at 98%, no the phone when i restart it only shows the RGB screen in the beginning and thats it. During the update process, the programs gives error 302, and them he gives me a rescue button which works fine but then i have to restart the update process but it still fails.
I though that the were both CID en lock free but maybe this one wasn't unlocked.
Can someone tell me how I can fix this vario?
Stuck in the bootloader eh?
The solution here fixed that for me many times
http://forum.xda-developers.com/showthread.php?t=276963
Hope it helps
Hey guys,
Really sorry if this a repeat of a previous discussion. I am new to posting.
I have never had any problems loading new ROMS, have had an 8125 and an 8525 and installed several different roms with no problem at all. Recently I bought a tilt several days ago. I had the issue with the white screen when installing SPL so I used jumpSPL. This worked but when I was installing the ROM it only got to 19 percent. I completed the recovery but still nothing happened. After this I used mtty.exe, a very nice program I might add, and used the boot command. Phone boots fine and everything works, however whenever I soft/hard reset I am stuck back on the bootloader screen and have to use mtty again. My question is this: How can I recover the original bootloader? Whenever I try to run any ROMS it stays at 0 percent. Someone please help.
Thank you
Figured I left some information out. I currently have service with ATT. On the bootloader screen top left: KAIS1*0, SPL-1.56.0000, CPLD-8....top right:RUUNBH
Contact me if assistance is still required or see the post regarding MTTY by L26.
READ BEFORE YOU FLASH! You have flashed without the use of HardSPL. This is the quick way to a brick.
Hello again,
I been flashing ROMS for a while now but now I having some problems that I can't solve.
Since I installed the Laurentius26_KaiserDiamond_V10 I can't update the rom anymore. The Kaiser connects to the update, the update program confirms the connection (it checks if the battery is above 50%, confirm the previous fiirmware, etc.)
When the program shows the progress bar (On the PC) the kaiser screen blimp one time to the grey screen (the one with the progression bar) and turn back to three collors screen (in less than a second). After one or two minutes the program (on the PC) gives a erro message.
I have to reset the Kaiser but no ROM was installed
Does anyone know how to solve this problem? I'm using SPL 3.29 but I have already tried Hard SPL 3.28 and back to the 3.29 again.
Thanks
Hi there,
That happened to me too. What I had to do was to download the original rom from HTC and flash that. After, i did the usual: hard reset, remove batter, restart computer. Then I could flash
Michael
Diamond: dutty 1.8 full
Kaiser: Romeos 4.3
Check the link in My Sig.
Ta
Dave
I tried your sugestions. Tried to flash the original Orange ROM but had the same problem as the cooked ROMs. It stopped at the three colors screen.
I think myh problem is a little different from other cases here. My phone is working with the Rom it have right now. It only got stuck on the three color screen when trying to flash a new Rom. To remove the screen is just reset it (normal reset, no hard reset) and it goes back to 'normal' but with the old rom. Can't flash a new one
Also tried the mtty.exe method, but when I open the mtty it shows "CLIENT". If I push any key it shows one more "CLIENTE". after 34 "CLIENT" Messages (it shows "CLIENTCLIENTCLIENTCLIENT" it freezes...
Can someone help me please?
Thanks
Try flashing the new Hard SPL be cmonex.
http://forum.xda-developers.com/showthread.php?t=420683
Thanks
Dave
Hi, I've got the HTC Touch Pro (Raphael)
And I've had it in my drawer for a while becuase it broke down one morning and I just bought a new one, But I'm thinking of sorting out the problems with it now since I need an extra phone.
The main problem with it is that it locks up in boot.
If I do a normal boot it locks at the HTC logo and the "friendly dinging sound"
I was thinking of reflashing it, but since it never boots up the only flashing I can think of is through the SD card.
So i put the file "RAPHIMG.nbh" in the root folder of my SD card and booted it up using the volume button pressed to looad the loader, it swaps over to a loading screen then it just freezes here aswell.
Any ideas on to WHY this happens and HOW to solve the issue.
issue solved, I managed to get the bootloader to get to waiting mode and cet a connection to it from my windows computer and run a default ROM onto it, now I can start modding it
i couldnt help but notice this thread, im am facing the same problem, except that my phone has never been flashed before, its fully stock. how did you manage to load a ROM beyond the "Loading..." screen. i have done exactly what several guides, including the ones i found in the forum, have told me to. Neither the SD card flash, nor the Activesync flash are working.. help please?
flashing
try tsis :http://forum.xda-developers.com/showthread.php?t=540290
I've tryed this on Touch Pro and it works , but do only the driver replace on windows......don't do task 29 or else .Instal the driver bring the phone into a bootloader and flash a stock rom...
hope it will do...