Related
Hi, I've on Cingular's network using Faria's WM6 ROM w/ radio ROM 02.25.11 . I don't always get my voicemail notification. Sometimes I will get a notification that says "5 new Voice messages" Why didn't I get notified about the 1st one??!
Has anyone else had this problem? Just today I got a message saying "6 New Voice Messages" and one was from today, the rest were from up to a week ago! help!
-Jordan
Cingular 8125
unlocked
rom's at boot listed as:
2.25
2.25
02.25.11
2.18.00
read the threads on this issue please.. there are numerous threads stating there are problems and the best thing to do is to downgrade radio to 2.19uk
jacob-mda said:
read the threads on this issue please.. there are numerous threads stating there are problems and the best thing to do is to downgrade radio to 2.19uk
Click to expand...
Click to collapse
Yes, but he get's the messages that he lost the calls...I would blame the provider too for that. Just to be sure, read a little not to regret alot.
anichillus said:
Yes, but he get's the messages that he lost the calls...I would blame the provider too for that. Just to be sure, read a little not to regret alot.
Click to expand...
Click to collapse
Anichillus has a point here. If one checks the HTC America site for the official 8125 download, it uses .... 2.25
This is one of the behaviours I've seen with radio's higher than 2.19 on WM6 with Cingular network. I'll have lots of missed calls and SMS, and then hours later, I'll get notification about VM (and sometimes no notification at all).
So switch to the Tmobile 2.19 UK radio (or some even say a 2.07 Radio) and you should find things like this don't happen (at least it seems to work just fine on my phone with every WM6 rom I've run (and I've run most of them)).
Ok, I just installed to the 2.19 UK radio... I'll tell you how it goes..
-Jordan
hi -
the problems: since flashing 2 weeks ago my vario III only works for voice and data in gsm only mode - with 3G enabled i generally can't make or receive a call or connect to data, but the device . Everything works when i switch to GSM only...
The complications/wierdness: straight after flashing a new rom or radio i have sometimes been able to get the device to connect to 3G or make a call - but this usually only last for one session or so.
What i've done: i've installed just about every combination of ROM and Radio i can find - including all of the 6.1 radios with Dutty's 6.1, the "official" vodafone 6.1 rom, alex's, schaps, and i've tried going back to 6.0 roms and the 1.27.12.32 and .11 radios but still the same
what is the verdict? bricked? or am i missing something....
<crosses fingers>
wilbur said:
hi -
the problems: since flashing 2 weeks ago my vario III only works for voice and data in gsm only mode - with 3G enabled i generally can't make or receive a call or connect to data, but the device . Everything works when i switch to GSM only...
The complications/wierdness: straight after flashing a new rom or radio i have sometimes been able to get the device to connect to 3G or make a call - but this usually only last for one session or so.
What i've done: i've installed just about every combination of ROM and Radio i can find - including all of the 6.1 radios with Dutty's 6.1, the "official" vodafone 6.1 rom, alex's, schaps, and i've tried going back to 6.0 roms and the 1.27.12.32 and .11 radios but still the same
what is the verdict? bricked? or am i missing something....
<crosses fingers>
Click to expand...
Click to collapse
I don't think it's bricked.. if it was bricked your device wouldn't even turn on.
Did you hard reset after each flash?
Was it working before your original flash?
answers to both: yes
- working fine before i flashed it
- I've been obeying Dutty's rebooting advice - how could I ignore instruction given in bold AND capitals?
I'm having the same problems. Thinking of putting origional ROM with radio back on and removing hardspl and returning under warrenty but cant find origional splash screen anywhere! Help would be appreciated
had the same problem with my tilt...changed sim card ...different roms ...radios ...basically everthing i could do....but in the end called at&t and they sent me a replacement...goodluck
I had a similiar situation but with my GPS.
The Tilt I bought just 1 month ago was a GPS Champ, always acquired a lock quick. I had flashed XDA-Live v1.5 right over the at&t 1.62 Rom (after HardSPL of course).
Then I used th enew SIM/CID Unlocker (with the hacked Polaris Radio) and of course flashed back to the at&t Radio (from the leaked at&t 1.60 Rom).
Since then I had a coupel of times where the GPS locked-up and required a soft reset.
So yesterday I flashed a WM6.1 Rom and a Niki Radio as I've seen a lot of user report excellent results.
It made my GPS useless. I quickly reflashed XDA Live v1.5 (with the Radio from the at&t 1.60 Rom) but my GPS still seemed lost.
Ironically today is day #29 of the 30 on this Tilt so last night I removed HardSPL and flashed the Official at&t 1.62 Released Rom using the Official exe and everything figuring I'd returnt he unit today.
Wouldn't you know it, I tested the GPS and even on the untouched at&t Rom it was working better than it had ever worked before!
Now I know that the Radio in at&t 1.60, 1.61 & 1.62 are *supposed* to be the exact same but I can say that the over from at&t 1.62 fixed a problem that the 1.60 Rom's radio couldn't. Yes, I do a hard reset after each flash already.
Heck when my daughters return from Disney I'm going to flash the 1.62 version fo the at&t Radio onto my oldest's Kaiser and see if it improved her GPS also.
seems like everyone who replied has a tilt not a VIII. Are you sure your settings are correct for your network? that would be my first guess at this point input them manually and dont use the connection wizard app as sometimes it doesnt work right. also check your phone settings make sure its set to AUTO or UTMS only if all else falls force it into 3G mode using the Band settings post your results back please
martyotaku said:
had the same problem with my tilt...changed sim card ...different roms ...radios ...basically everthing i could do....but in the end called at&t and they sent me a replacement...goodluck
Click to expand...
Click to collapse
hey I am having a similar problem at my house when i first got my tilt i have a very strong 3G signal here. That tilt messed up sent it in and this new one that i got worked just fine till i flashed a new rom on it now it wont pick up 3G unless i go somewhere else and come back to my apt. And yes i HardSPL'ed it and hard reset after flashing. I even went back to stock tilt rom and that didn't work. I have tried all the radio's on this forum from stock to the new imported NIKI radio's nothing has brought it back. When I go get the 3G signal elsewhere and comeback god forbid i have to soft reset because there goes 3G out the window and locked to edge. Should i return to AT&T for an exchange or is there a fix i'm not finding?
austinsnyc said:
seems like everyone who replied has a tilt not a VIII. Are you sure your settings are correct for your network? that would be my first guess at this point input them manually and dont use the connection wizard app as sometimes it doesnt work right. also check your phone settings make sure its set to AUTO or UTMS only if all else falls force it into 3G mode using the Band settings post your results back please
Click to expand...
Click to collapse
The Tilt Roms by default don't allow manual band selection.
Bad Data settings wouldn't cause poor reception just inability to connect (regardless of 3G or Edge/Gprs) for data sessions.
Based on my experience I would say first test is to do the work and reset your phone to the latest shipped Carrier Rom for your Carrier and see if your problems persist.
When I was having my GPS issues I also had a few wierd Call issues like calls not disconnecting (I had to toggle the phone radio to actually end the call).
wilbur said:
hi -
the problems: since flashing 2 weeks ago my vario III only works for voice and data in gsm only mode - with 3G enabled i generally can't make or receive a call or connect to data, but the device . Everything works when i switch to GSM only...
<crosses fingers>
Click to expand...
Click to collapse
I had the same issue with a t-mobile(UK) viii. The issue appeared after a while using the phone before I'd got into flashing different ROMS. In the end, i had the unit swapped out and the problems went away and have not returned. You can assume its a hardware issue. I went through the is it your SIM, is it this... is it that... after explaining that basically i was right next to a 3G transceiver in a big city.
Like I mentioned, this was a fault which developed after two months of no issues.
Old hardware version (looking under battery cover):
DATE:061107(TB02)/EU
New phone:
date:090807(RB01)/EU
I have had the same issue. I have returned the phone today and exchanged on my insurance. the new phone works fine.
thanks for all the feedback - shame there isn't a fix ..
austinsnyc: thanks for your help...
- i was using the connection wizard (difference i've noticed was that it includes a proxy server which i don't when i set up manually) so i created a new connection manually
- i've changed to 3G-only and i got "no service" (though i have previously got it to work)
- i put it on auto, it registered 2G then showed 3G signal in the taskbar. Tried to connect to my manually created connection - no joy: "cannot connect for an unknown reason etc".... then i got "no signal" for about 30 seconds, then full bars of gsm, then shows 3G again....
changed back to gsm only - works fine.
I'm not exactly sure t-mobile are going to take it back!... i'll have to hunt down the original t-mobile uk rom first....
got my new tilt in yesterday and it works totally fine like i thought in my apt. If you could wilbur i would definitely get a new one i think its the phone itself.
lol so i checked to see if switching off the 3g on my new kaiser then switching back would cause the same problem and it sure did so now im stuck with edge in my damn apt. again. I wonder if these new kaiser's they're shipping out are different than the old ones, when i first bought mine at launch oct.5, 07 i could switch back and forth between 3g. Now with 3 new tilts i have gotten i cant do it anymore this blows Damn i should have never given that first one away damn
so annoying...
i upgraded to the latest Dutty Rom (the 6.1 hybrid) - sure enough, straight away after flashing i was able to use 3G to make and receive calls, and to make a data call (but it was really slow)... then, within 30 minutes, i was back to the old phone: cannot connect a 3G call and no connection to data... so annoying - i'd almost prefer it didn't work at all than tempt me with the prospect that one day i'll find a rom that works...
anyway - I'm going to need to replace it - anyone know which rom/radio combo i'd need to flash to convince the guys at T-Mobile to take my VIII back? and btw - does anyone have any experience of trying to return handsets covered in scratches?
can anyone tell me if these problems are linked to Flashing ROMS? Since i had my last Vario 3 replaced ive been apprehensive about flashing if this is what broke the last one but i really want to flash it again.
I have been experimenting with various kaiser radios recently. I have had good success with almost every radio I try BUT about every 45 minutes I will no longer be able to send/receive text messages, make or receive phone calls... In order to re-establish connectivity I must pull the battery, but it back in. power the phone back up, I will be told I have no service. Then I must once again pull the battery and try again. Usually on the second try I will get a signal. At that point its anything but reliable, it will drop connectivity, but still report a signal anywhere form 5-30 minutes after.
Currently Im running the official 3.34.721.2 WWE rom, 1.65.21.18 radio, and SPL-1.0.OliPof. I have a kaiser 130, unbranded, and my carrier is AT&T.
The issue existed with pdacorner v18, and every 1.7x.xx.xx I tried.
What am I missing?
My first guess would be your SPL, it's hella old. Try upgrading that to one from here, http://forum.xda-developers.com/showthread.php?t=420683
3.29 is most recommended one for newer roms
ok, flashed 3.29 hard2, i will have a status report in 30 (ish) minutes
Ok I tested the SIM in another phone, just for quality control. I no longer even get a signal. I tried both the 1.65.21.18 and the 1.71.09.01 radios. I also hard reset just for good measure for both radios. is there some kind of master-reset for the radio? i am going to leave the battery out for the rest of the evening.
After leaving the kaiser with the battery out for 6 hours, I still have the same issues. It plain doesn't make sense. Does anyone have any ideas?
reflash the stock at&t wm6.0 rom let it go threw its set up and all, then reflash the stock att 6.1 rom! i had similar issue with my phone at one time and just reflashing att 6.1 didnt fix it, had to do att6.0 then att6.1 then i was back up and running
Ok, I flashed the oldest wm6 wwe rom I could find. The problem did not get any better, I can no longer use wifi. What is the cause of this nonsense!!
similar problem here, but I had not updated the phone at all at this point. This week I've now tried AT&Ts official 6.1, HTC 3.34.721.2 with radio 1.70.19.09, nothing works.
Where about in the country are you guys located? Also, we should take this discussion to the radio thread here:
http://forum.xda-developers.com/showthread.php?t=393182
Please answer these for us:
Location!!!! Be specific, ie Cedar Rapids, Iowa.
Also, what is the exact current state of your phone? ROM info, Radio info, Hard SPL info.
As well, what phone were you using previous to the Tilt, or is it a problem that just surfaced? I know that if you don't have an AT&T 3G SIM card, it will have major issues if you try to use it with a 3G phone.
the0ne.john said:
Ok, I flashed the oldest wm6 wwe rom I could find. The problem did not get any better, I can no longer use wifi. What is the cause of this nonsense!!
Click to expand...
Click to collapse
Sell your Tilt and but a Tracfone. J/K
Same Issues
I'm having the same issues as the OP. I'm in Dallas, TX and I've tried different radios on several ROMs.
Currently I'm using radio 1.65.24.36. I've tried 1.71.09.01 and 1.65.16.25 also.
I'm attempting to flash back to an ATT OEM ROM, but judging from the OPs posts it seems like it might be a waste of time. My sim card is 3G and the phone was purchased in November. I might try getting the sim replaced and see what that does.
Swede405 said:
I'm having the same issues as the OP. I'm in Dallas, TX
Click to expand...
Click to collapse
It is a known problem with AT&T 3G services in cebteral Texas... it is a bit of an insider's secret. There is an excellent thread on www.phonescoop.com where AT&T emoyees discuss the matter. It is also prevalent in other areas of the country, and is a result of the switching boards for the 3G service not talking with one another properly.
Finding the right radio does make a difference, but it wil not be miraculous in it's improvement. I will post a link to the thread when i get a chance tomorrow afternoon, but if you go to phonescoop on your own, do a search of the forum for AT&T centeral texas and itshould bring it up in the first couple of results.
Here is the direct link for the thread talking about this:
http://www.phonescoop.com/carriers/forum.php?fm=m&ff=4&fi=2015964
Hey guys,
I recently got a Telstra TP2 on a new contract, but I can't stand what they've done to the ROM. For those who don't know, Telstra have added 4 extra tabs on TF3D (downloads, telstra applications, tv, news and sport) which can't be removed or turned off, and they've put 12 locked (unremovable) program shortcuts on the start menu.
As I'm in a rural area, I need the 850 band the Telstra version of the phone supplies, and I'm worried that flashing a new cooked rom will lose this functionality (I'm very new to this). As it is, the shipped version of the Telstra rom isn't found on this site through the wiki (version 1.19.841.3 (51489) wwe), so I'm scared that I'll lose it forever and won't be able to put it back on if something goes squirly.
Is there anyway I can get around this besides flashing a cooked rom, and possibly losing the shipped rom forever?
Also, have any other telstra users been able to use HDWall on the phone to replace the crappy blue telstra background throughout the device?
Many thanks,
Tim
Welcome to forums
Have a look on Rhodium ROM development and choose another ROM!
Good luck,
Thanks for the welcome
I've had a look around, making some heads and tails of it, but I really need to know if I'm going to lose my 850 band with Telstra if I flash another cooked rom without all this Telstra garbage on it.
No you wont
850 is a hardware stuff related and you cant change it with any ROM, so you can install
Just have a deep read on the how to section in rhodium rom development
Enjoy,
Hi there, me again.
I was at the Windows 7/Windows Phone pre-launch in Melbourne on Tuesday, and picked the brains of the Microsoft employees manning the Windows Phone booth showing off Winmo 6.5 on the TP2 and D2. One of the first things I was asked during the conversation was if I had already flashed 6.5 on my phone, which I was surprised about. I mentioned my reservations about losing the 850mhz band with Telstra NextG, and the employee told me that the support for the band is built into Telstra's crappy ROM, and would be lost if flashed with anything else.
Are they yanking my chain or what?
I would like to know this too.
I`ve changed my ROM twice, saved my original one.. and I`ve finally encountered a connectivity issue...
Perhaps it`s my using a Telstra, Unlocked HTC Touch Pro 2 with an Athine ROM (though it really doesn`t make any difference what ROM I use... Maybe) on my Rogers BlackBerry Internet plan.
But I`ve used the Sony Ericsson Xperia on it and a few weeks prior to this date, have had no problem surfing the internet.
It MAY be the fact that Rogers is having problems with their network in downtown Toronto, so I`m hoping it`s not my TP2...
In any case, I`m using HDWalls on my phone.. but I`m just (un)installing the individual walls as I go along.
There`s something wrong with my computer that I have to fix because I cannot install the items necessary to use HDsWalls on the phone, and on the computer.
But so far, it`s been the best.
Although, I just have to say.. if you don`t have anything like "background for all" sort of cab files on the phone, I believe;
1) The phone runs faster
2) The background quality is crisper/better
Took me 2 weeks for me to get my Telstra Touch Pro 2 from Australia to Canada, and it was worth it.
I BELIEVE just changing the ROM will do nothing to the radio.
Moving into radio talk, I was wondering if I updated my Telstra phone with the latest AT&T radio build, because the hardware is for 850mhz and so is the build...
Will it enhance my connectivity?
Does anyone have any expertise on this and help shed some light?
Hiya peeps well i am new at this so am not a out blown expert i did a lot of research and i could not find some answer to some wanted question on radio and stuff like that now where i should start
ok i had my treo 750 to att 2.25 and wm 6.1 and i wanted it unbranded to 2.27 so i followed the instruction and i tried to do the radio up date using cheetah but i most have did something not right, for this part i got one question
using a sim card in the network setting for band should it work on auto or its normal that i need to specified what band am using? or i did something to my radio? (and not talking what tower it should connect to that automatic am talking between gsm and umts since am on telus that uses bell/telus shared tower that on UMTS 850 / UMTS 1900 network code of 302880 since i did that at lease it said the right provider and its no longer disconnecting me or saying no service)
if i update my radio should i use from this site?
www crc.id.au/files/xda/Radio_Roms
if yes what version that is safely work with unbranded 2.27 and wm 6.1
if no then where i can find the right radio rom i can grab for my treo 750 and instruction how to install it lol
am trying to understand how the phone should be setup while using a sim card without any disconnection by the phone also gime ability of roaming as well since i like my phone to be able too for future use
anyway thanks for reading and really do hope someone reply
also P.S: about the roaming icon any solution to that?
When you flash an OS ROM, it doesn't change the radio ROM. You have to flash it seperately.
I would suggest you only use the most recent radio ROM for your provider.
I have used 1.54.07 and 1.54.27 on my AT&T Treo 750 with success.
The Treo uses Hermes ROM's ... here is the repository.
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
Do not install 1.54.30.10 ... it's not a great radio from many accounts and once flashed, you will be stuck with it. You can't flash a new radio over the top of it.
ok now the radio is updated and it work i used the 1.54.07.00 so now am happy for that part but i got 1 more treo 750 i could not updated the radio due to there spl is 0.25 then 1.40 like my main one i normally test on them other treo so if they turn into a brick i would not care lol
is there a way to update a bootloader or i miss something somewhere?
Sounds like you need to Hard SPL the second phone.
well that what am trying to do when i do try with the hard spl v7 it does not work it goes blank so am trying to see if i can find a bootloader that 1.40 so i can so the same thing on the second phone to test radios and other kinky stuff
also on the side spot i notice that my phone fails to auto detect its band and the only way i can make it work is to select the right band for my provider is it coz i didn;t completely unlock my radio or i did something that bad? or re-flash the phone?
Anyone tried the 1.48 Radio ROM. Some are claiming better battery life than the 1.54.
xmadragex said:
well that what am trying to do when i do try with the hard spl v7 it does not work it goes blank so am trying to see if i can find a bootloader that 1.40 so i can so the same thing on the second phone to test radios and other kinky stuff
also on the side spot i notice that my phone fails to auto detect its band and the only way i can make it work is to select the right band for my provider is it coz i didn;t completely unlock my radio or i did something that bad? or re-flash the phone?
Click to expand...
Click to collapse
I wasn't aware there was a v7 to Hard SPL, I just used the version in the first post of the HardSPL sticky here in the Treo 750 forum. It's worked on both Treo's I have tried it on. I would say re-download and re-format the SD card and try again?
As for having to select bands on your phone, my guess is whatever ROM you have flashed might not have the carrier information for your provider included, or your radio might not support the proper bands. Telus doesn't use the same 3G bands as AT&T, but Rogers does. Depending on which version of the phone you have, that could be the issue.
rdecker692000 said:
Anyone tried the 1.48 Radio ROM. Some are claiming better battery life than the 1.54.
Click to expand...
Click to collapse
I tried it on AT&T and both the 1.54.07 and 1.54.27 ROMS were far better in terms of reception for me. Can't remember on the battery life since it's been awhile, but have to believe at the time if it was an issue I would have made the change back.
startngate said:
I tried it on AT&T and both the 1.54.07 and 1.54.27 ROMS were far better in terms of reception for me. Can't remember on the battery life since it's been awhile, but have to believe at the time if it was an issue I would have made the change back.
Click to expand...
Click to collapse
Okay - mine has 1.54.27 on it so I'll leave well enough alone. I just got this off of eBay (non camera version so I can take it to certain places at work) so I'm not sure what to expect for performance. The orginal battery lasted about 1/2 day so I just got a new OEM original battery and still burning it in.
Thanks for the tip.
rdecker692000 said:
Okay - mine has 1.54.27 on it so I'll leave well enough alone. I just got this off of eBay (non camera version so I can take it to certain places at work) so I'm not sure what to expect for performance. The orginal battery lasted about 1/2 day so I just got a new OEM original battery and still burning it in.
Thanks for the tip.
Click to expand...
Click to collapse
I've always been able to get through the day without issue, but can't say I'm a heavy user.
The stock battery is 1200mAh, but Innocell makes a 1600 mAh battery that fits in the OEM space if you need more juice.
http://www.seidioonline.com/product-p/basi16tr680s.htm
startngate said:
I wasn't aware there was a v7 to Hard SPL, I just used the version in the first post of the HardSPL sticky here in the Treo 750 forum. It's worked on both Treo's I have tried it on. I would say re-download and re-format the SD card and try again?
As for having to select bands on your phone, my guess is whatever ROM you have flashed might not have the carrier information for your provider included, or your radio might not support the proper bands. Telus doesn't use the same 3G bands as AT&T, but Rogers does. Depending on which version of the phone you have, that could be the issue.
I tried it on AT&T and both the 1.54.07 and 1.54.27 ROMS were far better in terms of reception for me. Can't remember on the battery life since it's been awhile, but have to believe at the time if it was an issue I would have made the change back.
Click to expand...
Click to collapse
well can ya link me the right hardspl
for my band selection problem is it the OS rom or the Radio rom and if there is one for my carrier where i can find it?
xmadragex said:
well can ya link me the right hardspl
Click to expand...
Click to collapse
It's the first 'sticky' thread in this forum as I previously mentioned.
http://forum.xda-developers.com/showthread.php?t=334100
xmadragex said:
for my band selection problem is it the OS rom or the Radio rom and if there is one for my carrier where i can find it?
Click to expand...
Click to collapse
It's likely not the OS ROM causing it. Assuming you have other phones that lock onto a signal properly in the same locations, then it's probably the radio ROM. However, if the Treo in question was not originally sold for your carrier (which I assume is Telus) then it's possible that the phone is trying to find a frequency for 3G that is not supported by Telus. For example, AT&T shares the same 3G frequencies with Rogers, which are different from Telus'. If you have a Rogers or AT&T version of the Treo, you would probably be better off just locking the phone down to GSM only.
As for finding the proper radio, you would need to try to find any Telus radio ROM that you can. Have no idea what that would be, or where to find it. If you have the original WM5 or WM6 official Telus installer package it would likely be included there. Otherwise you are just going to have to scour the net in seach of it.
Hmm, in my tests it is the OS that handles the Band selection only, what bands the Treo supports is up to the Radio firmware. You can flash a radio that, say, doesn't support UMTS 850, and yet it's possible to write a code to have it selectable.
And a word of advice. If you flash any of those Hermes ROM's, there's no taking it out. No overwriting. So, say if your wireless carrier upgrades their network like mine did, there's no going back to any of the suitable Radios that you can find.
And, just to be helpful, I'll write down which Official Treo Radio can be found in where(the ones I have):
CNG 1.16 (Cingular WM5) with Radio 1.12c [no HSDPA enabled by default]
VFU/VFE 2.18 (Vodafone UK and EU WM6) 2.18 with radio 1.47.02.00 [fast HSPDA on UMTS 2100 band]
H3E 2.19 (H3E Australia WM6) with radio 1.52.30.00 [no GSM locking, AUS band]
ROW 2.23 (WWE Generic WM6) with radio 1.54.00.00 [equal performance on all bands]
ATT/CNG 2.25 (AT&T WM6) with radio 1.54.27.00[Optimized for 1900/850 UMTS bands]
TEL 2.26 (Telstra WM6) with radio 1.54.31.00 [Extra band locking to single UMTS band (850)]
ROG/ROW 2.27 (Rogers and WWE WM6) with radio 1.54.01.00 [Slight performance increase over ROW 2.23]
VFE 2.30 (Vodafone New Zealand WM6) with radio 1.54.02.00 [bug fixes and improvements over ROG/ROW 2.27]
All personally flashed and extensively tested by me on two wireless carriers testing all bands.
mangatron said:
Hmm, in my tests it is the OS that handles the Band selection only, what bands the Treo supports is up to the Radio firmware. You can flash a radio that, say, doesn't support UMTS 850, and yet it's possible to write a code to have it selectable.
And a word of advice. If you flash any of those Hermes ROM's, there's no taking it out. No overwriting. So, say if your wireless carrier upgrades their network like mine did, there's no going back to any of the suitable Radios that you can find.
And, just to be helpful, I'll write down which Official Treo Radio can be found in where(the ones I have):
CNG 1.16 (Cingular WM5) with Radio 1.12c [no HSDPA enabled by default]
VFU/VFE 2.18 (Vodafone UK and EU WM6) 2.18 with radio 1.47.02.00 [fast HSPDA on UMTS 2100 band]
H3E 2.19 (H3E Australia WM6) with radio 1.52.30.00 [no GSM locking, AUS band]
ROW 2.23 (WWE Generic WM6) with radio 1.54.00.00 [equal performance on all bands]
ATT/CNG 2.25 (AT&T WM6) with radio 1.54.27.00[Optimized for 1900/850 UMTS bands]
TEL 2.26 (Telstra WM6) with radio 1.54.31.00 [Extra band locking to single UMTS band (850)]
ROG/ROW 2.27 (Rogers and WWE WM6) with radio 1.54.01.00 [Slight performance increase over ROW 2.23]
VFE 2.30 (Vodafone New Zealand WM6) with radio 1.54.02.00 [bug fixes and improvements over ROG/ROW 2.27]
All personally flashed and extensively tested by me on two wireless carriers testing all bands.
Click to expand...
Click to collapse
I guess we have different experiences then. I have had improvements in my phone locking onto a signal by changing radio ROMs without changing the OS ROM. I also have also used several of the Hermes radio ROM's and have been able to flash new radios without issue. The only exception I have ever seen is the 1.54.30.10 ROM which was widely reported to be impossible to flash over once installed (which for that reason I never tried).
I took from the OP that he was having trouble with his phone locking onto a signal and it was showing up as roaming a lot. I guess my thought was that perhaps he had a phone that wasn't originally sold for his network and it was trying to lock onto a band his carrier didn't support. Logically it seems like that might cause his problem, but I'm not well versed enough to know for sure.
As I mentioned, I am on AT&T and am using the 1.54.27 radio you report. It's the best of the radio ROMs I have tried. The Hermes 1.54.07 was the second best I tried. Thanks for the list, I'm sure it will help a lot of people. Of course you will now start getting requests to post them ...
Heh, when I said it's the OS that controls th selection, I mean just that, basically the drop-down menu in Band Selection. I too know that one can flash new radio's without changing OS's (you don't even have to Clear Data to use the new radio, just edit your choice of Data Connection setting, save, and your phone will automatically re-list your internet setup for use), and that's the thing. The OS will retain the Drop-down menu selection of bands, as it is tied to the OS (or both .pxp packages), an example is several tests I tried, for example the H3E ROM, does not have a selection for "GSM only" in the network type list. Say, if you flashed the ATT radio only then it will still retain the lack of GSM, because it is tied to the OS.
And yeah, I'm sure there would be at least one request. The problem is, I lost my source of instructions for ripping the Radio Firmware from the .nbh files and I do not want people having bricked Treo's all because I didn't follow instructions [I don't have]. Other course of action is to share th ROM itself, but that's large and I don't have an always on connection (this here Treo is my only source for internet, tether and built-in browser)
By the way, there are a lot of others who could not flash over other Hermes Radios, not that .10 one. I myself have 2 AT&T Treo's, and I flashed radio 1.50.00.00 and it remained no matter what I used to flash over it. I eventually gave away that half past dead Treo :/
well it used to be on auto with my telus card and it works on 3g network, the problem happend when i updated my treo 750 to 2.27 from 2.25 with wm6.1 am starting to think i mightn eed to reflash the rom it self
ok my wife as a fido sim card indeed i think its telus sim card the problem i have to use selective band it didn't needed that before i turn the phone from 2.25 ATT to 2.27 rwe the fido card work with the last radio version and i finally updated the bootloader
telus work with selective band >.>
now to know why fido card work auto but not telus
what does the radio do?
i got radio 1.54 .and i got two battery indicator when i installed HTC home (six tabs)
one bat is full and the other is like by bar. i want to remove the two battery because i got some newer/cooler battery indicator.
and i search some radios (idk why) so i try to installed other radios. and my phone stucks at the three colors.
and something pops up to my mind. i use cheetah unlocker. it got
FLASH SPL
RADIO.
idk the one.
so i flash spl and till i get to radio. it automatically updates to 1.1six some other icons on task bar changes.
but what does the radio do? and i dont know.
-sorry for the Six. because my Sixth button on keyboard is broken.