Related
I have bought a Plantronics M3000 bluetooth headset for my QTEK 2020. I have no problems pairing, calling and answering. However the headset just shuts off after a few minutes of conversation. It doesn't just cut the conversation but shuts off. I can make multiple short calls but nothing longer than 3/4 minutes. It works, however, without problems on my wife's Ericsson T68. Anyone can help ? Thanks.
Marek
Hello,
I have the MDA2 (same as QTek2020) and a Plantronics M3000 and It's been working just fine.
The problem you describe it's very weird since you mentioned that the headset works fine with your wife's mobile, and that makes me think that your QTek has some sort of problem with the Bluetooth stack or hardware.
It may be well worth to try (if possible) another headset just to make sure that is not the M3000 fault.
Do you see any type of error or message on the screen at the time of disconnection?
Does it always cut the conversation at the exact same moment?
Does the problem match the time the QTek takes to power save?
Any other clues?
Thanks.
I did not have the occasion to test another BT headset on the Qtek. When it shuts down there isn't any message displayed.
I have no problems with the BT stack (with the Pocket Bluetooth Tools patch) when using it with a BT GPS (Emtac) receiver, it works for hours.
However, your suggestion that it might happen when the Qtek goes in energy saving mode is interesting. I will check that tomorrow.
I'll post the result.
Hi
I seem to have a similar poblem after installing pocket bluetooth tools!.
I use a Jabra BT 250..and I noticed that the headset just mutes during the call..
I am generally used to switching off the display of the XDA after placing the call to power save ...
So I discovered that the headset would mute whenever i switch off the xda after making the call (which it never did prior to installing PBT)!
any thoughts on that?
maybe it has to do with the auto switch off plugin?
Actually I just experienced that too...
If I place (or answer a call) the next time I try to use the phone via the BT headset I notice the BT headset was turned off... Yeah, it could be related to the Powersave feature on the today plugin that PBT installs as a plugin... :roll:
Need to investigate...
Best regards,
Rayan
Both my bt headsets have stopped working since installing pocket bluetooth tools latest version, I have reverted back to version 1005 and everything is fine. I have a sony-ericsson EBH-65 and a skypower clip on headset.
my platronics does the same also its annoying you cant even transfer the call back to the device you have to hand up turn off bt and then turn it abck on and headset mode back on it also does the same on my pc
when im on msn using it as a headset it just d/c and i have to turn it off and turn it back on again
dont see what the problem is
btw the range on the xda2 and platronics is amazing i had it on my bedrooms desk and i went outside it passed through the living room wall and the patio window and i was stood 5m down my garden im sure it would of been over 10m and it was still working if i kept still when i moved it went crackly but ah well lol
just hope someone sorts the prob out
Hi,
I was having the same problem with the M3000. I just had confirmation from Plantronics that this problem is a bug in the product that occurs with the XDA II. I am currently in the process of returning the product.
Regards...Mike
Same problem M3000 doesn't work. Give up now before too much frustration makes you feel ill.
Try the Hello 2 headset. Work with my Aussie XDA2 and is very small and lightweight. Even had a neck chain to carry it around like a USB drive.
I have tried searching the forums and can't find much Info.
Is anybody here using the above system for telephony & GPS; If so how do they intergrate/do they work well on the XDA II (I have ROM Version 1.72 with Radio1.17)
I Know about the headset profile probs not giving full functionality of the Handsfree use of the car kit but this doesn't bother me to much as long as I can Make and receive calls.
Thanks in anticipation!
I was going to get a CK3100, but heard so many problems regarding build quality, and lack of support, I got a HCB 30 instead.
It did not help when I tried to e-mail parrot for advice and 3 different e-mail adresses bounced back.
Works Perfect!
Just had the CK3300 installed today and it works perfectly - I Knew some of the functions didn't work because the XDA2 only supports headset profile but once you have transferred your contacts to the kit via bluetooth it works well.
Also the GPS works well with CoPilot 5 live; it picked up the signal straight away ; well pleased with this set up!!
same to me have the ck3300 tested with qtek2020 - works fine. problems with 9090 but after bluetooth update now it works fine. No tests with S100 at this time.
tested GPS with destinator 3 and map&guide fleet navigator and mobileobjects fleet management system.
don't use bluetooth tools after Rom 1.66 :!: CK3x00 didn't work aber installation of this
Set up
Just had the CK3300 installed today and it works perfectly - I Knew some of the functions didn't work because the XDA2 only supports headset profile but once you have transferred your contacts to the kit via bluetooth it works well.
Also the GPS works well with CoPilot 5 live; it picked up the signal straight away ; well pleased with this set up!!
Click to expand...
Click to collapse
Any tips on setting up the CK3300 with my XDA2?
Just had the car kit fitted - i need both nav and handsfree functions - but i am not sure that i have got the phone and ck3300 to bond properly. So everything is 'greyed out' on the parrot.
Using ROM 1.72.00WWE (1.72.181) and radio 1.17.00
Thanks for any help received.
If everything is greyed out then it isn't bonded properly!
Step 1
Delete the pairings you have from XDA2 and car Kit;
Step 2
On the car kit turn the control knob untill settings appear- then scroll to 'Advanced Settings' - 'pairing a telephone' - 'windows CE device'
Step 3
Now search for devices using your XDA2 and the car kit should be shown.
Step 4
Enter passcode 1234 and accept headset and serial profiles when shown.
PAIRING COMPLETE
to access your phonebook you need to transfere the contacts via bluetooth to the car kit.
Hope this helps
XDA2 CK3300
Managed to get the GPS set up (fiddling with COM ports - even imbeciles strike lucky sometimes)
Some items are now in black. However, I am not sure that I have done it right as I cannot get it to use my phone to make calls or receive them. Which is exactly why I bought it in the first place.
So, please (please please) can you tell me how to exchange my phonebook?
I am going to sit in the car right now and have a go at your bonding advice...maybe all will become clear (but that is not often my experience!)
Thanks again for your help.
You need to bond the phones in the manner I described or it will not work ; this is clearly ststed in the Parrot instructions and on their website.
(I have noticed a strong correlation between people who do not read instructions and complain things do not work!!) - Joke
You also need to make sure your headset profile is active on the XDA 2 for it to work. Again reading the instructions for the phonebook - you tap and hold a contact on the XDA2 and select 'beam contact' - 'via bluetooth' the bluetooth search then comes up and the car kit will be found you then 'tap to send'
Now i have the opposite problem!
Believe it or not, I have now got the XDA2 and the CK3300 bonding automatically so I can make and receive calls whilst driving. It works pretty well (occasionally makes an awful noise, but only occasionally). I am impressed.
However, once I had done that, the GPS is undetectable. I have tried all sorts of combinations. I have checked the instructions - and selected the long code (ends in 9600) but I am not certain that I am using the right com port. I have tried most of them without success.
Oddly, this is the one thing that WAS working before I got the car kit to work (for calls). Somehow, either I have lost the right settings OR the XDA2 won't do both (although I read somewhere that it would) OR my ROM needs updating (uh?)
Please help.
BTW, I am due a phone upgrade - I love the xda2 but would consider getting another phone if necessary, if anyone can recommend one that is fully CK3300 and TomTom compatible.
I don't use Tom Tom myself but from reading these forums I think you need to install the patch on their website to allow Tom Tom to use the correct Port .
Your Car Kit also needs it's software updating if it makes a noise like you say. On the Car Kit go to > settings-advanced settings-information and you will find the software version (sounds like 4.03) if it makes a noise. The latest on the Parrot website is 4.10b and this will fix the noise issue.
If you need help installing this let me know.
The best Phone is surprisingly the Old Fashioned Nokia 6310i - it has a good bluetooth stack and uses the handsfree profile rather than the headset so contacts sync automatically but if you require live traffic info best stick with what you got as the Nokia will not pair with the XDAII and the car kit at same time.
Which COM port?
For the moment, I have a temporary solution.
However, I have updated the TomTom Navigator software and the GPS, but still don't know which port the GPS in the CK3300 should be connected to.
Any ideas?
And, thanks Nikpro for the excellent help so far - you are a true altruist and a star!
The outbound port on the xdaII is port 5 by default
On XDAII go to Settings - System tab - Bluetooth settings and make sure you check the tick box for outbound COM port.
There is also a chance you have deleted your serial port profile so tap on the bluetooth icon in the Today Screen and go to bonded devices. Select the CK3300 and delete partnership (do not delete pairing from car kit end!)
Then search for new devices from the XDAII and the CK3300 will again come up; create a new partenship and everything should be good.
Still having problems
Oddly, I still cannot use the GPS on the CK3300.
I am using my old TomTom at the moment for GPS and the CK3300 for headset - which works fine, but I wanted the CK3300 to do both.
When I try and reset the GPS to the (series of numbers ending in 9600) as stated in the info and the instructions (Nikpro, take note - I have read them - but your comment made me laugh), the TomTom just 'freezes'. Wait - and wait - and wait - and when it reincarnates itself, no GPS at all.
I am using the 1.72.00WWE rom and radio 1.17.00
I think that I have tried every permutation for the COM port.
Has anyone any ideas? Please?
When you initially pair your XDA to the car kit do you get a message about serial connection show on the screen? The problem must be with the tom tom software as with copilot and mapopolis it works fine? or the way you are pairing the two!
What software version is the car kit? PLEASE DESCRIBE HOW YOU ARE PAIRING THE DEVICES??
Hi all, 1st post and all that.
Have you tried falshing the parrot with the newest rom, mine picked up enough to make and recieve call, but i flashed my xdaII with 2.02.T1WWE this morning and it works even better.
Hope you get a result
nikpro said:
I don't use Tom Tom myself but from reading these forums I think you need to install the patch on their website to allow Tom Tom to use the correct Port .
Your Car Kit also needs it's software updating if it makes a noise like you say. On the Car Kit go to > settings-advanced settings-information and you will find the software version (sounds like 4.03) if it makes a noise. The latest on the Parrot website is 4.10b and this will fix the noise issue.
If you need help installing this let me know.
The best Phone is surprisingly the Old Fashioned Nokia 6310i - it has a good bluetooth stack and uses the handsfree profile rather than the headset so contacts sync automatically but if you require live traffic info best stick with what you got as the Nokia will not pair with the XDAII and the car kit at same time.
Click to expand...
Click to collapse
Use Bluetooth tools www.bluetooth.jazztel.es
and edit the registry under hkey local machine, builtin, BTIBserial, rename BTIBserial.dll into BTIOBserial.dll
and go Start, Settings, System, Bluetooth settings and check both inbound and outbound.
Delete ALL paired devices, reboot, and re pair them.
You will now have an option for two serial ports, one for each device.
This is the only way to do it if you have two devices that need a serial port. If you have a third, you are SOL.
Normally, the stupid programmers who made the MS BT program, made it so it only had one dynamic port for BT. Some people would experience having to reboot before switching BT devices, most would have to re pair every dam time.
The new 2005 does not have this problem but it has other bugs.
They smart people at MS changed the databases so Mapopolis and other third party programs can not read the contacts or have other bugs with them. Plus the 2005 version here limits your memory.
The 2.02 - 2.06 will NOT work with Hands Free and most car kits need it and if you have caller ID via BT, you are SOL too.
The 2.20 is a stable and a good OS and the Hands free works much better. The down side is, when I get a call on the call waiting, even if I did not answer, it would disconnect the BT headset and no sound through the phone too. I would have to, click on Tools, Hands Free off, tools Hands
Free on before it would work. I have lost many clients this way.
I decided to disable call waiting in the phone settings and it only has a few bugs now like I have to turn off and then back on the BT headset after ever call or it would revert to Headset mode.
The caller ID will not display if the call is in the history of my BT headset or if it is in my contacts database.
I mention my BT headset because it is like a car system when used in Hands free mode.
Good luck, let me know if you have any trouble now.
Parrot 3100 with XDA II
Hello,
I have just put in a Parrot 3100 and it works fine as a handsfree phone.
is there any way when I am not in the car though to use my Jabra 250v headset without rebonding and selecting it as the preferred headset device?
I can't seem to switch between the Parrot and the Jabra when the other one is not in use without repairing.
Thanks for any advice
BT
Try turning of one and turning on the other and soft reset..
Ok, I have just spent my entire weekend trying to get my Qtek 9090 to communicate to my newly installed Parrot CK3300 (with GPS). I have read the manual about 3 times from beginning to end, know the whole website parrot.biz by hard (ugly site BTW), and have tried about everything in configuring, but with no success so far.
Initially I had the 2 devices paired to each other, but after I installed Tom Tom 3, it is impossible for me to get them to pair again. Nevertheless, the 2 devices "see" each other (when asked in "Linked devices"), but they can not get to communicate. From all the stuff I have read on forums and sites, it seems that I need to upgrade my Bluetooth version, but I have no idea how and where to start this procedure.
Can anyone help me out here ?
Any tips are welcome !
Hi All,
I just had a brand new Car with Bluetooth. (Citroen C4 Grande Picasso)
With this Bluetooth I should have the abbility to to connect, answer, and scroll trough the contacts, of my phone. I'm using a Wizard G3 with WM6 (Dutch) IPL/ SPL 3.08 and Radio: 1.08. (Radio will be updated soon)
Probelm is: stuff is not working! I can connect the phone to the car with Bluetooth and it is recognizing it. When I make a call or one comes in, the Car sees it and mutes the audio. But that's all. I do not hear anything and I can't be heard. Also the button (on the steering wheel) for contacts doesn't work; meaning: It says: there are no contacts.
Who experienced the same pproblems and more important who solved these?
Hi Jedeve,
I have the same problem with the same car. It worked for me when I first started TT and then automatically my bluetooth GPS mouse was connected and all was working fine. Strnage but true. It looks like if a channel is set open when connecting to the bluetooth GPS mouse and stay open so evrything is working. I also have looked into registry setting son bluetooth if I can find differences by using diff but no strange differences where found.
I also talked to the Citroen dealer and they told that it might be possible that new telephones with the newest software are not able to work correctly with the carkit.
I have a Wizard (I think a G3) with Octavoi 9.2 on it, IPL/ SPL 3.08 and Radio: 2.71.11.
Hi,
same car and same problem here.
It seems worked with WM5 and problem showed after upgrading to WM6.
Calling/answering from car controls ends with total silence most times.
I've noticed that if a call is answered from phone it works most times.
Also car phonebook seems support only latin characters and any contacts with non-latin ones(cyrillic in my case) do not appear on car.
Would appreciate any suggestions/solution to above problems.
Hi,
I have same problem, with same car! with TNT wm6 Roms!
With new TNT 6.1 did not try yet...
Now I have Slim wm6.1 ROM and no problem! With NTS wm6 rom not problem too... works fine!
Hi,
I am using my HTC Touch Pro with an Opel Vectra built-in bluetooth carkit.
All functions, like browsing the address book and call registers, are working fine. However, at random times, my carkit reports no phone. When I then check my Touch Pro's bluetooth status, I see that it is has been disabled.
After manually re-enabling it, I can pair with my carkit for as long as it takes for bluetooth to turn itselves off again.
I've already tested with JETware, but that does not change anything. Also tried the universal broadcom bluetooth stack, but doesn't seem to work on the Touch Pro. HTC only comes with a standard answer that they don't support all carkits and headsets... Since the BT stack on the phone seems to crash, I don't think it's a carkit issue.
Anyone here with the same issue? And maybe a solution?
Thanks and regards!!
Start -> Settings -> Connections -> Bluetooth -> Timeout (tab). Turn off Visible mode set to "Never".
I think this must be your problem.
Hi Freco,
Thanks for your reply! This option is set. However it's not really the visibility that turns to invisible, but the whole bluetooth stack is being turned off completely. Need to fully re-enable it via Comm Manager.
Any other options? Does anyone know if there is a working broadcomm stack for the Touch Pro?
Regards!
Hi,
I have exactly the same problem with a Vauxhall kit, I have tried all sorts of things, but nothing seems to work
try:
start -> settings -> connections -> bluetooth
timeout tab
select 'never' from drop down box
Hi Brendo,
Unfortunately this doesn't solve the issue. Once paired, the connection even works without being visible. It's also not a fixed period of time before the disconnect takes place (can be within a minute, sometimes after half an hour). However, the whole bluetooth icons disappears from the top icon bar and comm manager shows it's turned off completely.
Hope somebody has any other ideas, because the only thing HTC can do is point to the carkit vendor :-(. Since all functionality is there when connected and the phone is turning off BT in some way, I really don't think this is caused by the carkit vendor. I should at least expect BT to stay enabled on the phone.
Thanks!
Yes, same here, BTW I have tried this in my Friends Saab, and the same problem.
same problem here with a Opel DVD90 buildin bluetooth carkit.
With other htc phones it always worked like a charm, but my mda vario IV continuously disconnects after a random time period and shuts down the complete stack.
Try this!
I have the same problem with my opel with original bluetooth-kit (2007). On the touch pro I changed the band and network from auto to GSM, as G3 reseption in this area is quit poor, especialy while driving. It helped for me, at least the last few days. I agree this has been an annoying problem.
I have tried to switch to "GSM only mode" in the past, but as far as I remember it does not completely solve the issue. However, I will give it another shot! Actually I can't figure out at what point it occurs... It can happen within a minute or after half an hour without using any funtion.
Does one of you know if there is a way to do some debugging on the Bluetooth stack?
And has anyone experience with other Windows Mobile 6.1 based phones in this combination (just curious if it's a WM issue or HTC only)?
Furthermore I did some tests with JetWare. You should be able to limit the number of synchronised items then (might be related to this issue). However, it looks like this configured limit is being totally ignored: when I limit my recent call list to 5 with JetWare, it still syncs about 25 items. Anyone tested with Jetware?
I have tried the GSM only mode, this didn't help either
I have now given up and got myself a Nokia E66, which works perfectly.
All contacts are pushed to car, no disconnects and AD2P works so my mp3 ringtones play through the car speakers! Sweet
Word of note, I had issues with N-Series phones, would connect ok, but contacts would not push.
I have the samen problem with my HTC Touch Pro and Saab.
bluetooth pairs just fine with my pioneer bluetooth enabled deck, but the problem iwth mine is once i receive a call sometimes no sound comes from the car, instead the earpiece is still on. but if i initiate the call first sound works just fine and earpiece on the phone is disabled, BUT once the call is ended bluetooth disconnects randomly and the phone takes a good 1-2min to reconnect. i absolutely hate the bluetooth on this phone!
ExTREmE99 said:
bluetooth pairs just fine with my pioneer bluetooth enabled deck, but the problem iwth mine is once i receive a call sometimes no sound comes from the car, instead the earpiece is still on. but if i initiate the call first sound works just fine and earpiece on the phone is disabled, BUT once the call is ended bluetooth disconnects randomly and the phone takes a good 1-2min to reconnect. i absolutely hate the bluetooth on this phone!
Click to expand...
Click to collapse
I am having the same problems you describe. Anyone got an suggestions???
I encountered the same problem; first with an opel udp carkit and next with the bluetooth interface software from homeseer.
It has something to do with phone signal loss.
With the opel carkit I noticed bluetooth automatically turns off when the phonesignal switched from 3g to gsm.
I also noticed that in my home, BT turns off whenever I have been in a room with no phone-signal reception.
try this thread, both registry change and attached cab file, reset. DOn't worry if the make visible to all option is unchecked.
http://forum.xda-developers.com/archive/index.php/t-314996.html
My touch pro seems to have real bluetooth issues with my JVC KD-NX5000 stereo system. My kaiser worked flawlessly with it but with the touch pro it wont pair at times and when it does it wont let me use any of the many functions that the stereo offers (voice dialing, downloaded phonebook, etc) I assume this is a problem with the ms bluetooth stack and was wondering how tough of a job it would be to switch to a broadcomm stack or if anyone has thought about making a custom rom with the broadcomm stack. Just curious if Im the only one with issues with wm 6.1 and bluetooth.
i have the same problem with my diamnd anbd jvc car audio
Slightly OT rant:-
I had the opposite problem with pioneer + broadcom...
Pioneer only looks for handsets which identify themselves as phone or smartphone, and my device identified itself as a pda.
I actually told pioneer about the problem, and rather than forwarding on to the developers, I got a stock reply:-
"This phone is not on our compatibility list" (so we don't care)
So I went and got an MS based phone (you can change it to smartphone with a regedit).
Never buying pioneer again...
- Anthony
Similiar issue with my opel carkit.
Tried to make the broadcom stack working, but got a memory error when opening its blue tooth manager.
After uninstalling, bluetooth didn't work at all anymore, needed to perform a hard reset.
Has anyone successfully installed the broadcom BT stack on the touchpro/raphael?
I found that my Touch Pro would pair and then drop out when connecting to my Kenwood DDX5032 car stereo bluetooth adaptor. I couldn't dial from the Kenwood kit, couldn't use A2DP (wouldn't even connect), and really couldn't use any Headset Profile functions at all.
I persisted with pairing and unpairing in different ways (you can initiate the pairing from the Kenwood itself rather than the phone), but nothing really worked.
Then trinode's post about changing a registry setting sent me down that track and now everything is working fine
I found the relevant setting from http://forum.xda-developers.com/showthread.php?t=290871, which is [HKLM\Software\Microsoft\Bluetooth\sys\COD], and then changed the HTC TP default value of '5898764' (decimal), to the value from my old Dopod838Pro, which was '5374228' (in decimal).
I didn't even need to repair the Kewood to the HTC TP - it just worked straight away, as if it said "Oh, sorry, did you want me to work? I thought you wanted me to be in 'stupid' mode! My bad - everything will work now."
So all good, and thanks to trinode for pointing me in the right direction.
Codenix.
After hard-resetting my Touch Pro to fix another separate issue, now this problem has come back and this time changing the COD value hasn't fixed it. It would appear my previous post may have attributed my success to the wrong thing
The search for the answer continues!
I found a firmware update for my Kenwood's bluetooth adaptor which fixed the problem. I don't know why it ever worked at all before this update, but there you go!
I'll create a separate thread to share this with others in case anyone else out there has a Kenwood bluetooth kit and a Touch Pro or a Diamond.
Thanks.
The thread I created re the Kenwood is at http://forum.xda-developers.com/showthread.php?p=2835805
@ Trinode
Pioneer sent my unit back, but never told me that my phone was not supported. Where did you flag the smartphone in the registry? Did it fix the BT connection/unti reboot issue? I had a AVIC F500BT (sold it) now have a AVIC X910BT same issue as the 500 had.
@ Trinode. I found the hack , tried it, but it still doesn't resolve my issue. Are there any other mods out there for the BT Stack prob?