Related
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
denflorida said:
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
Click to expand...
Click to collapse
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
1. Disconnect your phone from the usb cable,shut down any firewall,disable any Anti virus,Reboot your PC.
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. On your PC Open windows Task Manager...>Tab Processes...>wescomm.exe...>End process
4. Power off the phone completely (Not stand-by,shut off completely),or you may take the battery out for few seconds
5. Make sure your phone is not Connected to the PC via USB cable and remove the dummy Sdcard or mini-Sd card
6. Get your phone into Bootloader mode (Multicolor screen) by pressing camera button + Power on button
7. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Be sure that your battery is charged over 70%)
8. "USB"will appear on the bottom of the screen of the Bootloader (Multicolor screen)
9. Run the Upgrade again and it will work fine without any problems.
10.Never use Bluetooth sync for the Upgrade
While upgrading, the ActiveSync program will not go on, however the upgrade is running.Please be patient when you're flashing your device, even if 98%. It can wait a little bit, 5 ~ 7 minutes.
Don't cancell the flash or get the phone off the usb cable till it confirms "Congratulations" or stops with an Error!!!
Hope it'll work, Good luck
Hi, this is the first time i saw a Paki guy on this web. I know there is alot of talent in IT profession in Pakistan. Anyway its good to see u here and i got a relief that with the help of a senior member like you i can get my phone work again.
To cut the chase, I have X01HT by Softbank Japan. It is Herms200 by HTC Japanese WM5 ROM. I have installed Asukal's English MUI and it was working fine for me. Now i'm planning to visit Pakistan this month so i though to unlock the sim and i used Prof v3a to unlock. I've successfully unlocked the sim and i guess CID also. When i use some other carrier's sim, i can receive the calls but cant make the calls out coz Softbank rom has a security which comes at screen and ask for password and dont let me do anything on the PDA. After studying alot on this forum i figured that i need to change the rom to get rid of that password message. i used the Olipro's Hard SPL and got bootloader 2.10 Olipro. I checked the other necessary stuff and when satisfied i started rom update. I end up with the same message of Error 260. Now my phone has no OS and it starts at bootloader. i tried everything possible like i make sure to remove all firewalls on my PC, used all the versions of Activesync and everything possible that i could. I trust that there is nothing wrong with the ROM etc but it is with connection.
Now if i update to the original ROM, i'm afraid that it will also upgrade my Bootloader and could never be able to flash english rom. I'm really depressed for the last three days and loosing sleep as well. I trust that you or any other senior member can help me with this.
Thanks in advance and looking forward anxiously.
Farrukh, wrong forum.
You know you have a Hermes, then you should know to post your questions in Hermes related forum, not wizard.
denflorida:
Try to update other Radio-only ROMs in xda's FTP server.
Sorry Brother, i know i have herms but i couldn't find some related topic in herms and i figured that Activesync problem is the same in all devices.
Anyway, thanks for the prompt reply. I'll try to find some from Herms.
Thanks
8125 rom update
i have tried to do a rom update on my 8125 g4. i recently purchased it off ebay and i have two problems. the reason i want to update it is because when i try to enable the wifi my device freezes. the other problem is that i can not seem to get the phone into boot loader mode. i have tried :
-turning the phone off and holding the camera button as i turn it on.
-holding the camera button and pluging it in to a usb port.
- using wizard service tool to enter boot loader mode.
after each of these different attempts i had to either remove the battery for 3 secs or hold the reset button for a few seconds before i can turn it back on. the phone still turns and just i can not use the wifi
Yes!!! Thank you! your instructions worked for me and got me past the Error [260] with my 8125 .
zabardast_1 said:
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
Click to expand...
Click to collapse
Thanks! Worked for Topaz and latest radio update.
so yea, iono what happened to my mda. i cant seem to turn it on. when i press the reset and camera buttons, it worked before and brought me into bootloader. and that was actually all i could do. now, i cant even get it on, iono whats happened to it. im trying and atempting rigorously to charge it so i can try to fix it. but the charge light dusnt even come on... i dont know what happend. please help me analyzed. i really want to fix this back ._.''
You may need to use the factory charger to charge your device. I keep hearing the problem people experience when trying to charge a completely dead battery with a usb charger. the factory charger is 1amp while usb is half that. that may be why it wouldnt charge.
also, when the phone is in bootloader (tricollor bars) the power does not turn off.
you may need to charge your device completely before turning it on; then flash the original rom to it.
anothor thing about flashing while in bootloader:
If you connect the usb and XP does not recognize it, you have to unplug it, reset the device, then connect the usb again. as soon as you hear the found hardware noise, open the rom upgrade utility. flash. should work.
when posting a question such as this, it helps to provide as much information about the device and the circumstances under which it failed. this being an electronic forum, it is difficult to play detective to find out what you did wrong to mess up the machene.
also remember that it is a machene. it can not ousmart you, but you can outsmart it.
Which is your device,what were you doing when this happened,were you trying to flash a rom ?
bricked Cing. 8125
my device just bricked on my while updating also. not sure why, i use a Cingular 8125. i flashed it to the t-mobile 1.2 rom (like i always do) and then tried flashing it to a new rom and about halfway through it bricked up. now activesync wont even recognize it. how can i fix this?
Bricked up is an over used word on these forums. If it does nothing no lights no charge when you put a fully charged battery in it, then its a brick.
Anyway here is me repeating myself yet again. A Wizard WONT CHARGE A BATTERY without windows mobile running. So charge the battery in another wizard or orbit or buy an external desktop charger /cradle with a spare battery slot or a new battery because it wont charge it
Not really...
Wizard can charge without powered on (when not bricked). It just can't charge if the battery is too flat.
starkwong said:
Not really...
Wizard can charge without powered on (when not bricked). It just can't charge if the battery is too flat.
Click to expand...
Click to collapse
It will charge a completely "flat" or dead battery with the original factory charger. the one that has the output of 1amp, not the usb, which is .5amp
so yea, sorry about this confusing post. sop what i was trying to do was changing my wizard love rom to XM6r5...but i dont know how
what i did was use shelltool and pooped it. but now iono how to really fix it. im still confused now cuz i cant boot up at all. i can get into the bootloader r/g/b screen
but iono how to fix it from there
sound to me like you may not have unlocked your device?
maybe.
try this: reset your phone with the reset button;
put it in bootloader (tricolorscreen) reset holding the camera button while untill it is in bootloader;
plug in the usb;
run the update utility.
as it updates, it will seem to freeze at 100%. do not unplug it.
I recomend you flash the love rom first.
but it says it cant even connect when i pplug my usb to the pc and device
th pc dun really "see" it
and the ruu, dont you need active sync on as well or sumthin? nothin shows up
m1k0e said:
but it says it cant even connect when i pplug my usb to the pc and device
th pc dun really "see" it
and the ruu, dont you need active sync on as well or sumthin? nothin shows up
Click to expand...
Click to collapse
try reseting it. then put it into bootloader; then plug it in; then run the flasher.
if you unplug it while it is in bootloader, then plug it in again it will not read.
exit everything (meaning flashing utility unplug usb; reset phone)
then try it again.
just a side note, dus it matter which ruu im using to do this? or should i use the wizard love first?
okayt so i have tried it, but curiously, how do i know if its actually working when i do that? cuz everytime im in bootloader and open ruu, it goes at first, but the status dusnt move past 0% and then an error message comes up. does it matter ifi supposedly have other programs open in the b/g?
I think it matters which ruu you are using depending on if you have a G4 or G3.
If you have a g4 then use the ruu for a g4.
the guy who designed the wizard service tool would know.
I would flash to the factory rom though to fix any issues first.
what is your IPL SPL? G3 or G4?
well, at least we know that your phone is not bricked. It will get fixed under the right circumstances.
It could be that your battery is not charged all the way.
remove the battery, then put it back in. charge it fully (overnight) and try to flash it to the factory rom.
well i upgraded my rom to wizard love previously, so apparently its a g4 now. i want to upgrade to the XM6r5 ruu but im not too sure.
maybe u could help locate me a few stable and nice roms for g4?
but thanks so far
when i run the RUU, i keep getting an errormessage 260, saying it cant connect my phone to the pc.,..
have you gotten it unbricked yet?
need more infoon your phone and it's current state.
everytime you post a message (it seems) you do not give enough information.
ipl spl current rom ...
I dont know any of these things. untill I do, I can't help you.
If you search the G4 forum you will find information on flashing your phone if it is a G4. (you may need to soft spl or hard spl your phone) look to the G4 forum for information for that.
just because it had the love rom does not mean that it is a g4. all roms that have OS ONLY can be flashed to a G4. If it has SPL/IPL (bootloader) Or extended roms can not be flashed to a G4
oh. haha sorry. now it just boots straight into the bootloader with "ruu" on the upper right hand corner.
ipl is 2.26.0001
spl is 2.26.0001
m1k0e said:
oh. haha sorry. now it just boots straight into the bootloader with "ruu" on the upper right hand corner.
ipl is 2.26.0001
spl is 2.26.0001
Click to expand...
Click to collapse
Its a G4,you can only upgrade through either SoftSPL or HardSPL,read about this in the G4 sub-forum posted as stickies.
but how would i use hardSPL thru only bootloadeR?
update: everytime i restart my phone, it keeps booting up into the bootloader screen with "RU" on the upper right of the screen
m1k0e said:
but how would i use hardSPL thru only bootloadeR?
update: everytime i restart my phone, it keeps booting up into the bootloader screen with "RU" on the upper right of the screen
Click to expand...
Click to collapse
ok,download official carrier's rom, get into Bootloaders,hook up the phone with pc via usb,Now Check,if small usb appears at the bottom of the Bootloader screen,if its there than Run the Ruu in the rom to flash it,but if it doesn't appear,its not establishing connection with pc and phone.There might be a connectivity problem,it cud be usb cable,mini usb port of the phone or usb input of pc.
Yes! you can only do HardSPL if its working normal,you can even try to flash wizard_love rom and if it flashes,then go for HardSPL.but official carrier's rom will be more appropriate and recommended,it will also remove any Extended_Rom corruption,if any.
I have read through endless posts and stickies.. I still can't figure out what the correct procedure is for updating my TYTN II from WM6.0 to WM6.1
I would greatly appreciate it, if someone would lay it out step my step
I tried to flash with the WM6.1 update, it said there was a vender error.
I tried flashing with HardSPL 3.28 and it stops at 0% and says there is there is a communication error, and to click next to perform the recovery. I perform the recovery, after removing the battery and putting it back in, the phone starts up normal.
I tried the white screen solution.. it reaches the three coloured display with USB and just sits there.. i eventually reboot the phone.. and it starts back up normally..
but none of the flashing procedures have worked yet..
I used the files found Here for the white screen problem.
I don't know what else to try..
Direct update - Invalid Vendor ID
HardSPL 3.28 - Communication Error
JumpSPL - Does nothing...
What am i missing?
Puff1911 said:
What am i missing?
Click to expand...
Click to collapse
Interpreation and sense of what you are reading.
http://hpcmonex.net/olipro/KaiserUnlocker.zip
That is the link to the Kaiser Unlocker by Olipro. It Hard-SPL's and SIM Unlocks. If you do not need the sim unlock simply flash to a different ROM after the first step.
Thanks socalkevin21 for providing a usable response
Not a problem, let me know if you have any issues.
The software says to unplug the USB connection as soon as the screen turns to the three coloured screen.
when i plug back in, the progress bar waits a couple seconds then jumps directly to 100%.. is that correct?
The phone reboots, and starts back up as normal.. but the same version ROM is still there..
Puff1911 said:
The software says to unplug the USB connection as soon as the screen turns to the three coloured screen.
when i plug back in, the progress bar waits a couple seconds then jumps directly to 100%.. is that correct?
The phone reboots, and starts back up as normal.. but the same version ROM is still there..
Click to expand...
Click to collapse
enter bootloader (press and hold the camera button all the way while pushing the stylus into the reset hole)
you should now be at a tri-color screen
what does this screen say?
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
when I click on Unlock Radio, it says "incompatible device"
Is that also normal?
Do i need to patch the radio as well?
wooooo!!! got it! i eventually got it to update the radio by clicking the button over and over..
I didn't get to unlock the phone (step 3).. but after i tried to update to windows mobile 6.1.. and it worked!
Thanks socalkevin21 and mbarvian!!
Well my device runs a lot faster.. but also sticks a helluva lot more!
Also my camera doesn't show anything, it takes pictures fine.. but there is no live display.. anyone having that problem?
And i also lost Voice Commander.. anyone have the install files for that?
**Fixed the camera problem. I had installed the HTC camera patch... Problem solved after removing it.**
Puff1911 said:
Well my device runs a lot faster.. but also sticks a helluva lot more!
Also my camera doesn't show anything, it takes pictures fine.. but there is no live display.. anyone having that problem?
And i also lost Voice Commander.. anyone have the install files for that?
**Fixed the camera problem. I had installed the HTC camera patch... Problem solved after removing it.**
Click to expand...
Click to collapse
Try a new HardSPL.
WM6.1 freezes sometimes with the OliPof 1.0 Hard SPL.
All the latest Hard SPL's are here: http://forum.xda-developers.com/showthread.php?t=396922
There are no other differences between 1 and 3.* other than the version number - they both work the same (oh and no MFG in 3.*, but you won't notice that)
Ta
Dave
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
bsgbelg said:
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
Click to expand...
Click to collapse
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Not possible to flash anything
what I've tried so far:
- activate active sync to install hardSPL. Not working
- install HardSPL through microSD. Not working
- install ROM through SD. Not working
I tried a non HCSD for a change, and then I see the loading scree flashing up, but quickly says No rom found and returns to the bootloader screen.
The only thing that works is load the bootloader (red green blue white) into a screen that says:
KAIS130
SPL-3.29.0000
CPLD-8
Serial
When connected to USB, it says USB, but no disk is showing in Explorer or any connection is made to AS
The only thing I've done in the past is flash the 6.1 rom through the system provided by HTC with a file called RUU_Kaiser_HTC_NLD_3.29.404.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe
Please help, I really like this phone and hate to loose it
put it into bootloader, connect it to the computer and then flash one of the htc roms. make sure its an htc rom, you cant flash a custom rom cause you dont have hardspl
I have not been able to find the original rom, only the exe from htc which says Connect with active sync. Do I have to set it in bootloader and then execute the program?
Solved
Just want to let you know I sorted it out!
Flashing the original rom does not need active sync, the bootloader USB connection is sufficient.
After this, the phone restarted in 'Erasing memory' mode, but was able to finish it and reinstall the whole rom.
I believe I got the taste of it and will start testing some other roms...
msd24200 said:
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Click to expand...
Click to collapse
Thanks, worked fine
majedaly said:
Thanks, worked fine
Click to expand...
Click to collapse
good to know
So,i upgraded my i-mate jamin whit touchflow 3d lookII,and before the upgrade is finish i got a message: update error!!!!!!!!!! And now my pda is dead,no flashing the led when i connecting the pc,and if i want to run the original rom back the program say:connection error! I can't do hard reset because my pda don't want switch on!
Please if somebody can,help me.
play007 said:
So,i upgraded my i-mate jamin whit touchflow 3d lookII,and before the upgrade is finish i got a message: update error!!!!!!!!!! And now my pda is dead,no flashing the led when i connecting the pc,and if i want to run the original rom back the program say:connection error! I can't do hard reset because my pda don't want switch on!
Please if somebody can,help me.
Click to expand...
Click to collapse
wait we need more Details id you try leaving the phone charging then take battry out and put it back in? also does the Device power on? I mean do you see the qtex screen you know the boot screen? also try putting it in bootloader mode then flash
__________________
Thank you very much for your help.I tried everything, which you wrote, already. I cannot switch the device on. If I put it on a charger then sometimes automatically onto 2-3 seconds the bootloader appears,afterwards turns off.
He responds to nothing without a charger.Sorry for my bad english.
play007 said:
Thank you very much for your help.I tried everything, which you wrote, already. I cannot switch the device on. If I put it on a charger then sometimes automatically onto 2-3 seconds the bootloader appears,afterwards turns off.
He responds to nothing without a charger.Sorry for my bad english.
Click to expand...
Click to collapse
My Prophet has same symptom as yours. After 2 nights of charing, it now turns to charging light on all the time, no bootloader screen. After charging 1 day, it still on charging lamp. still cannot turn on, still cannot connect with PC.
what happens