818Pro dead after upgrade wrong ROM - JAMin, XDA Neo, S200 Software Upgrading

Dear All pleae help me, I upgrade the ROM for my friend 818Pro, after upgarde the Display cannot on, the charge light(Orange) and bluetooth light(blue) just flashing. What shold I can do, Please help. Thanks

alright i think i have exactly the same problem here seems like i finally bricked it.
i installed a vodafone compact s update for a wizard over a no vendor id update utility.
no when i turn it on it turns off after 1-2 seconds i can go into bootloader but it turns of after 1-2 seconds hard reset and soft reset stuff i did already hard reset is not working.
are there any other opportunities of working around that...? i guess not flashing with a turned of phone is bad^^
mh sd gold card probably? im trying that out^^
mh my ipl is on 2.21 and spl too
i got it to work so i'm in bootloader but only if its connected to the charger so i could probably flash over the sd card right?
usually ipl was on 2.15 and spl 2.21 maybe that helps...

Related

i think i have brick my dopod 818pro.. Please help

i think i have brick my dopod 818pro
have follow the step 1 and install without any error.
then installed the Cert_SPCS.cab and EnableRapi.cab.
then installed the Prophet_4.0.0.0.1_PV rom by running Upgrade_ROM.bat from the computer.
after that restat the device.
AND the phone boot after the HTC Innovation screen and stay at the loader screen.
NOw my screen only showing :
IPL 2.15.0001
spl 2.15.0001
gsm 02.69.21
os 4.0.0.0
and wouldn't boot in ???
anyone here please help
tq
finnally manage to boot in.
redo the step 1 in boot loader mode.
then installed the pdaviet 4.0.0.0.1 from pc
and it is done.
very nice screen
will try it out n c .
tq very much
Hi, how did you manage to solve the issue?
My situation is a little different.
-Load Step 1... ok Successful
-Load Upgrade_Rom.bat... completed
But when I reboot the PDA I just get this screen!!!
Nothing is responding.
PC cant detect the device.
Hard reset also get back to the same screen.
Please help
reboot your device into the bios screen (reset while holding camera button)
at that point i usually just put on the default WM5 comming from QTEK to reestablish operations.
i am using the prophet touch series from gullum and for that i do the following steps after having reestablished the WM5.
Put on PDAViet_TEMP
wait until phone restarts and shows 'Touch to get started'
Put on the Prohvet Touch (VIII or IX Beta)
Hard Reset (Com and Cam button, wait for the message asking to confirm afetr you release the reset button but hold on to com and cam buttons until message pops up) Confirm Hard Reset
So far i repeated this process about 6 times and it works every time
best of luck
need explanation
im planning to buy a dead prophet.....as the seller states...when he posted the pic, it still enters bootloader mode...but it shows
IPL: 1.00
SPL: 2.20.0001
Can this still be repaired? and is this possible? how can i repair it...it is being sold at a very cheap price
I've had similar issues and by just putting the original rom or the WM5 if you can enter bootloader mode thenit comes back to live. Once WM5 which is very stable is loaded, you can upgrade to the WM6 roms. Has always worked for me but it is a bit nerve racking to see the thing frozen. The key when upgrading is to use than WM5 rom and upgrade from there.

Wiazrd stops duing Initial Progrm Loader

To beguine i wont to thank all of you for making this forum possible. After hardSPl device and installed Wizard Love ROM i was trying to install kitchen ROM After i tryed Hard REseting it didnt ask me to tap Yes but just restarted and from now on i can se just the IPL Screen of Wizard Love With IPL 2.21.0001 SPL2.21Olip GSM 02.5.11 and OS 10.0.0.10 is this a BRICK meaning i downlded a wrong ROM by mistake and How can i get this running the ActiveSync Wont Connect in this mode and how can i get to bootloader screen thout a stylus my GF Lost it
Thnx
Oh, please try to write it slowly
Try holding your camera button and resetting. If it will enter a tri-colour mode (bootloader), it's alive. Just flash it again.
did you make that rom?
if so, it may be unicode rgu problem, imo.
if not, you made sth wrong..
if it is g4...oops.
sirtux said:
To beguine i wont to thank all of you for making this forum possible. After hardSPl device and installed Wizard Love ROM i was trying to install kitchen ROM After i tryed Hard REseting it didnt ask me to tap Yes but just restarted and from now on i can se just the IPL Screen of Wizard Love With IPL 2.21.0001 SPL2.21Olip GSM 02.5.11 and OS 10.0.0.10 is this a BRICK meaning i downlded a wrong ROM by mistake and How can i get this running the ActiveSync Wont Connect in this mode and how can i get to bootloader screen thout a stylus my GF Lost it
Thnx
Click to expand...
Click to collapse
Nopes !
Its not a Brick,just a bad flash.get it in bootloaders mode by pressing and keep holding the 'Camera' button and push the 'Power On' button,it'll go into bootloaders and flash the wizard_love rom again,hope it'll recover back.
And for god's sake get a new stylus,keep it away fgrom your GF
sirtux said:
To beguine i wont to thank all of you for making this forum possible. After hardSPl device and installed Wizard Love ROM i was trying to install kitchen ROM After i tryed Hard REseting it didnt ask me to tap Yes but just restarted and from now on i can se just the IPL Screen of Wizard Love With IPL 2.21.0001 SPL2.21Olip GSM 02.5.11 and OS 10.0.0.10 is this a BRICK meaning i downlded a wrong ROM by mistake and How can i get this running the ActiveSync Wont Connect in this mode and how can i get to bootloader screen thout a stylus my GF Lost it
Deleted
Click to expand...
Click to collapse

dead profit?

OK got a profit here that's had a bad rom attempt on it, all it does now is bounce to the bootloader and resets every 2 seconds?
If I plug it into the mains charger it goes to the bootloader and stays there but no charge light comes on.
If I plug it into a pc it just keeps rebooting to bootloader for about 1 second then reboots etc
on the bootloader screeen is:
RUU
IPL 2.26.0001
SPL 2.26.0001
is it dead, if so i'll stop searching for help and try and get a new one, if not is there a fix anyone has got? reload from sd card etc?
any help as every is appreciated, even if it's "your profit is dead"
catnip said:
OK got a profit here that's had a bad rom attempt on it, all it does now is bounce to the bootloader and resets every 2 seconds?
If I plug it into the mains charger it goes to the bootloader and stays there but no charge light comes on.
If I plug it into a pc it just keeps rebooting to bootloader for about 1 second then reboots etc
on the bootloader screeen is:
RUU
IPL 2.26.0001
SPL 2.26.0001
is it dead, if so i'll stop searching for help and try and get a new one, if not is there a fix anyone has got? reload from sd card etc?
any help as every is appreciated, even if it's "your profit is dead"
Click to expand...
Click to collapse
1. Is it a Prophet?
1.1 FIND A CHARGED BATTERY,
2. FORCE BOOTLOADER MODE MANUALLY~~~ THE ,
3. FLASH THE NVID (BETTER),
4. THEN UPGRADE TO WM6 (OPTIONALLY, YOU MAY TRY THE LAZY_TOOL)
http://forum.xda-developers.com/showthread.php?t=405454
GOOD LUCK ~~

Error 260 Update Error

Hi
I get this problem too often and I dont know why and what I did do when I dont get it. This is the case.
Now I have flashed the g3 wizard with one of the wm6-manilla roms. I have succeded with this once so I have followed the guides with the unlocking and downgrading etc. Now I have downloaded a new cook and try to install it by starting the rom update utility wizard.
Problem is that the installation ALWAYS fails now. It starts, the device disconnects from activesynk, waits another 30 seconds then fails to restart the device so I get the dreadful Error 260 update error and the phone is dead. I remove the battery, restart the device and try again and my hair turns grey.
I figure I need to downgrade first so I try all the differens RUU's that are pointed out in the guides (CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe, ruu_prodigy_226102_22610105_022511_tmous_wwe_ship.exe, Xda_MiniS_LaunchROM_v154102.exe) but always the same problem.
What am I missing?
WinXP
AS4.5
IPL 2.26
SPL 2.26
Once downgraded and CID unlocked,a G3 device will remain CID unlocked forever,there's no need to downgrade everytime you flash a new rom.Just simply flash a new rom whenever you desire.So don't reflash Button's Rom 1.05 before every flash,its just required to flash once to get IPL/SPL 1.xx for CID unlocking,after which there's no need to reflash it again.
Error 260 is due to open port,so reboot your pc and Soft Reset the phone,hope it'll work fine.If you have reflashed Button's Rom 1.05 and downgraded,it wud be better if you perform the CID unlocking procedure again through lokiwiz02b or WST_4.2.2,after that upgrade to IPL/SPL 2.xx by either flashing T_mobile 2.26 or any official aku 2 rom,then upgrade to any wm6.1 rom.
You can even take out the battery and leave it for 30 minutes,after that put it back and try to flash.
Hmm.. now I have rebooted the pc and disconnected the battery for 30 mins. No luck. Still the same error.
There must be something I have missed. I have flashed with several roms before w/o any trouble.
I am connected to activesync as a guest on usb-cable.
Oh i didnt downgrade because it failed that too. So right now im on a wm6 manilla pretty good rom but the wifi's gone
Try flashing from bootloader:
* Hold down the camera button and then softrest without letting go of the camera button.
You should se a pretty tri color screen with IPL/SPL Information.
* Connect Wizard to PC using usb and wait for windows to detect the drivers if they are not already installed.
* Start your RUU and follow the steps.
Normally this error occurs when trying to flash under vista, if this is the case visit a friend who has XP and take some coffee
It gets worse im afraid.. and I am under XP.
Now the phone wont pass the t-mobile bootscreen. It gets stuck when showing the IPL/SPL information.
I fail to enter the bootloader. Hopefully im doing something wrong.
I have tried this:
1) Holding down cam-button and pressing soft-reset. The phone boots as normal but stucks at same place.
2) soft-reset and when sceen goes black, hold cambutton. Doing this makes the boot halt totaly and the screen remains black. Looks like it turns off cause the softreset wont work and I have to press the powerbutton to get life signs again.
How (exactly) do I get it into bootloader?
Evolution... i managed to do a hard-reset and got the phone to boot up again. So back to square one with not being able to use the ubs+ruu
hmm very strange.. in a desperate attemt to get into bootmode i held down the voice-button instead of the cam-button and then power-on. Not it worked! Mystic....
***
update! problem solved
In case anyone else reads this. I rebooted the pc for the 10th time, rebooted the phone at the same time and (a dramatic paus here) i pulled the usb-cable and placed it in another slot in the pc. And there it goes...
I dont work with computers... i work against them!

Qtek S200 flashing problems

Hi,
I have a Qtec S200. G3
Now the problem is that I cannot flash it:
a) Using Softspl: the device screen sometimes turns bright white as it should, but when I start a RomUpdateUtility_NV_G3 it does not find my PDA
It tells to check my USB connections, which are ok.
b) Using Hardspl G3 found here, also at first produced the White screen, and when it came to the rom updating part, next, next, update-> the PDA screen turned black and eventually it could not connect to the PDA, displayed the same USB connection error.
c) Prophet Tools 2.8.3
Hardspl & Softspl are practically unusable, the same thing happens as above, softspl shows promise by entering into the "Bright white screen" state, but even then, when trying to "put" or "update" a rom to the pda in that bright white screen state, it still turns the screen black and does nothing, same connection error as before.
What could be the cause of this?
Any help would be appreciated
Details:
IPL 2.09
SPL 2.09.0000
GSM 02.07.20
OS 2.9.7.24
Help, anyone?
Help.. i have the same exact type of phone and the same error.. Can't get into SoftSPL and HardSPL doesnt work either. Really tired of WM5, nomatter how good it is
Today i tried to upgrade the IPL from 2.09 to 2.10 but still nothing. When i start the upgrade the phone turns off and wont start again until i pull the batter...
Any if all help would be welcome!
After a year i'm still stuck with this old ROM and the same problem as before.
Bump... Really could use some help on this
Same problem here
My S200 has the same issues.
But today when i tried to upgrade the IPL/SPL to 2.20 it worked and i was even able to hard spl .
I think the problem might be with the battery.Have you guys checked that out?
As for me,i am able to start flashing roms but the phone gets disconnected automatically in between.
I am going to try a whole night recharging and then flashing.
lets see if battery is the villain
my qtek s200 is mad
i tried to upgrade my rom from w to w6,and because i don't know how to do?my s200 has become unusable without charger,when hard reset it doesn't complete install process and it blocked,restarting it works unproperly,bud comands no sound no ...unpluging charger it turns off,battery is full "i'm sure ",but it indicate it empty 0% ???,
how can i syncronise it to pc and it is off
ipl 1.01
spl 2.20.0000
gsm 01.12.10
os 1.5.4.2
pleeeeeeeeeeeeeaaaaaaaaaaase heeeeeeeeeeeeeelp
Tomorrow i will try with my new battery..
Sofar, i know it boots into the 3 colour stripe menu when using RUU program and that's it, program crashes and phone stays the same..
Really hope battery is the solution..
BAttery change didnt do anything, still the same old ... cant upgrade.. anyone know if there is some upgrade block on some models?
BUmp.. the only phone i have been unable to flash is the S200.. ANY advice left in anybody?

Categories

Resources