I upgraded the device to wm5, when the device connected to gprs at start but when I make some phone calls it will disconnected and can't reconnected again. I must turn off the phone or soft reset the device then it will connect again? please help ....
edmondyu said:
I upgraded the device to wm5, when the device connected to gprs at start but when I make some phone calls it will disconnected and can't reconnected again. I must turn off the phone or soft reset the device then it will connect again? please help ....
Click to expand...
Click to collapse
I got the same problem. Any solution?
Related
When I start upgrading ROM (Qtek 1.11.00 final) my mini struck at boot loader screen and my PC struck at
"Checking the information from your device...please wait...
Don't disconnect your device from PC or power supply until
the upgrade is completed "
I have strucked at this screen for an hour
what should I do ? Please help me . Thank You
I think you have not disabled the activesync USB connection yet. Do so, and reconnect your mini to your laptop/pc via USB again. then run the installation program again, u should be alright.
tt's what I faced earlier.
zenkinz said:
I think you have not disabled the activesync USB connection yet. Do so, and reconnect your mini to your laptop/pc via USB again. then run the installation program again, u should be alright.
tt's what I faced earlier.
Click to expand...
Click to collapse
I've tried this and I'm still stuck in the opening screen. Any other advice?
Regards,
Rajesh
rajeshr said:
zenkinz said:
I think you have not disabled the activesync USB connection yet. Do so, and reconnect your mini to your laptop/pc via USB again. then run the installation program again, u should be alright.
tt's what I faced earlier.
Click to expand...
Click to collapse
I've tried this and I'm still stuck in the opening screen. Any other advice?
Regards,
Rajesh
Click to expand...
Click to collapse
1. first mini must be in bootloader mode (screen will show serial)
2. disable USB in activesync, plug mini to USB cable (new hardware detection should occur and mini screen will show USB instead)
3. USB cable direct connect to laptop/pc..dun use USB hub..
should work..
Even I had the same problem
Thanks a lot it is solved now 8)
my o2 neo not connecting to PC in bootloader mode.
My o2 neo got stucked on the o2 reset screen.After going through this forum i came to know that few others too had this problem, so i went ahead with flashing of rom (RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_ Ship.exe) as suggested. But i am having a problem connecting my o2 with my PC using activesync 4.1 as well as 4.5 as it is required for the process. I tried all the option for connecting in activesync, but it failed to connect. Pls help
Somebody pls help. I am having a problem connecting my o2 with my PC using activesync 4.1 as well as 4.5 as it is required for flasing ROM
My exda exec is in bootloader mode
My Xdaexec not connecting to PC in bootloader mode. While I was uograding the rom, the computer shutdown. And did not finish th upgrade. Please can any one help me how to solve this problem. Tanks a lot.
Can somebody pls help
prajai said:
Can somebody pls help
Click to expand...
Click to collapse
Did u try a hard reset?
Dear All Frenz..
Could anyone help me to solved this Problem? Currently
# on The Device
I already unchecked the Box for Advance network on USB Setting, Finally on The Actvesync connection menu, I checked the box of 'Synchronize all PCS bla bla.... '
# on the Laptop
I have Installed actvesync 4.5.0
When I tried to connect the Device to Laptop using USB Cable, anything Doesnt happen. The Icon of Activesync on Laptop screen did not give response (no flashing showing ).
But The Battery Charging running well as long as the Cable connected.
Maybe there is any procedure that I Have not tried yet.. Please tell me..
Do you have firewall??
Bulldog said:
Do you have firewall??
Click to expand...
Click to collapse
Yup Bro..
I hv the Fire wall in my LT and I Already
disable it,but didnt give any response
sorry becouse i have not given yet the information as below :
My Device has just been format, becouse I cannot access to Windows at the time of Turn on device. Before the windows problem happen, I didnt find a connection failed ( always success evry time physical connection began), but after format the connection problem appears. The LT cannot detect device evry time the cable already plug in to LT.
Please give me more advice.
Highly appreciate for your support
tommyx21 said:
Yup Bro..
I hv the Fire wall in my LT and I Already
disable it,but didnt give any response
sorry becouse i have not given yet the information as below :
My Device has just been format, becouse I cannot access to Windows at the time of Turn on device. Before the windows problem happen, I didnt find a connection failed ( always success evry time physical connection began), but after format the connection problem appears. The LT cannot detect device evry time the cable already plug in to LT.
Please give me more advice.
Highly appreciate for your support
Click to expand...
Click to collapse
tommyx21.. If I did understand you correctly..You had a Windows problem on your Laptop then you reformate it... then your problem with not able to connect your LG to Laptops began isnt???
When you plug in your LG to your Laptop do you see any sign of been connected as USB device? Have you reinstall the ActiveSync.
Bulldog said:
tommyx21.. If I did understand you correctly..You had a Windows problem on your Laptop then you reformate it... then your problem with not able to connect your LG to Laptops began isnt???
When you plug in your LG to your Laptop do you see any sign of been connected as USB device? Have you reinstall the ActiveSync.
Click to expand...
Click to collapse
I Hv format my LGKS20 device, not my LT Boss
for acouple time after format, i can see the sign with the" not recognize" notification (asking for driver). But After that My LGKs20 cannot be detected by LT anymore..
I hv tried to connect my device to PC, but it not given any change too...
I hv already tried to reinstall Actvesync and it given nothing...
any other suggestion boss? or maybe i must try to change my Connection cable with the new one..?
Hi there.
I have problem with my phone called Myphone Cube 4 GB
I need to connect phone to my pc without battery to install usb driver and then use flashtool to install rom on it.
But the problem is when i remove battery and try to connect it to pc it's still connecting and disconnecting over and over.
I see it in device manager on second and then gone. I don't know what's is wrong. It's second time when im flashing it and at first time everything goes perfect.
Now can't solve thsi why the phone still disconnecting form pc.
Any ideas guys ?
I had been hard resetting my Huawei phone and it ended up dying while resetting itself. My fault for not charging it before proceeding with the reset. Anywho, now it is stuck in FASTBOOT&RESCUE MODE which wont allow me to access my device. Whenever I connect it to my computer, Hisuite automatically starts up, but it continually states my device is not connected. Apparently, I need to have USB debugging enabled; but I am unable to do so without access to my phone. Does ANYONE know what to do? I have scoured everywhere and haven't found any successful solutions.
jayboi247 said:
I had been hard resetting my Huawei phone and it ended up dying while resetting itself. My fault for not charging it before proceeding with the reset. Anywho, now it is stuck in FASTBOOT&RESCUE MODE which wont allow me to access my device. Whenever I connect it to my computer, Hisuite automatically starts up, but it continually states my device is not connected. Apparently, I need to have USB debugging enabled; but I am unable to do so without access to my phone. Does ANYONE know what to do? I have scoured everywhere and haven't found any successful solutions.
Click to expand...
Click to collapse
This might help you, uninstall usb divers of your specific device which you have previously installed and try to install the latest version again..Connect your phone in main usb port not in secondary hubs..Try it and report..