Hi,
My Typhoon phone is freezed on the splashscreen (Blue sky with Qtek).
I want to upgrade the ROM but at this step it don't connect to the laptop.
How can I put th ephone in bootloader mode ?
Thx
I didn't know that Tornado and the Typhoon are the same.
Well try this, Turn off the phone, Press the Camera Key and Insert the USB Cable, and that will get you to the Bootloader Mode
or
Why don't you just try a Hard Reset first and see what will happen.
Goodluck.
Please transfer this on the Typhoon Category. Thanks
My device is a Tornado. (I dont know why I said Typhoon)
Now I am in bootloader mode. How can i upgrade the ROM ?
Thx.
Well Done ! I put my Tornado in bootloader mode. I have upgraded the ROM.
I am waiting for the result.
Related
Hi,
I have tryed to upgrade my rom to a new version (Prophet WM5 AKU3.2 v3231). Followed the stept correctly, however my phone does not boot anymore. It gets stuck in the qtek logo (when it displays the AKU version i´ve got) and the sceen gets all shacky.
An addictional problem is because it is stuck at that point it does not connect to my computer....
What can I do to fix this, any good suggestions
Thank,
Sebastiaan
You should be able to enter bootloader mode by pressing and holding the camera button while you power on your phone. On the bottom left, you should then see "USB" - connect it to the PC and flash it again.
Had to do this yesterday after flashing failed.
Mike
thanks it worked
Sebastiaan
Error [296] Upgrade Only
Hello
I have same Trouble & I Make Bootloder from USB but Always I get This Error
ERROR [296] UPGRADE ONLY
This NBF file connects used for your PDA Phone. Please get newer NBF file.
Note: I try to Upgrade to 2006-11-12_Prophet_WM5AKU2.3_lvsw_edition but my Phone Stack So I reset as say after 30 m
Now I trying to back to Old Software from I-mate
Also I try to upgrade to 2006-11-12_Prophet_WM5AKU2.3_lvsw_edition but no Connection....
Please help me I with out Live (Phone)
I know it sounds strange but i used a different USB port and then it did connect. Now that everything is back to normal i can use the old one again.
maybe it works for you as well
I tried doing that, but for some reason my computer doen't recognize the device...pls help!
Can someone upload an old ROM for the prophet? I can't start up my prophet, but I've got it in bootloader. So I nedd a little bit old ROM so I can install on it.
Understand?
Thanks!
Look for the first link here http://forum.xda-developers.com/showpost.php?p=1166927&postcount=2
Are this ROM old ROM?
Not really old but if your phone stuck in bootloader this one is ok
I can't make it, it says that i should connect to Active Sync, and how im I suppose to do that?
Go in bootloader (screen with 3 coulours) by Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
When you are in bootloader logicaly your PC must detect the Prophet, then run the update
Sorry for my bad English but I'm Franch
Yes i've got it in bootloader, and its stands USB on the PPC screen. But it aint the Active Sync that finds it, it says "Uknoknown Unit" or something when i connect them together..
Active Sync isn't a problem, update work or there is an error message?
In right corner down on the PC sreen it comes up "A unkknown Device connected" or something like that, nothing more is happening..??
It sayd that it can't recognize the unit..
Qtek_S200 said:
It sayd that it can't recognize the unit..
Click to expand...
Click to collapse
In bootloader mode, on connecting via usb ,if u r getting 'USB' written on left down corner of ppc then ur ppc can be flashed via proper RUU and nk.nbf
Be sure that this nk.nbf dont include ipl/spl parts for risk free flashing and for not getting brick device.
thanx
nandlal
Im trying to flash a ROM with that, but it coming up on the screen that "Not connected". It's standing that i nedd to connect with Active SYnc!!
could somebody upload an ipl/spl lower than 2.09 or higher but not 2.09^^
rest doesn't matter language english or german would be good...
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
hehh
same happend to me once. Go online and finde botton run , update utility 2.00.1
go step by step:
Disconnect your phone from the usb cable,disable any Firewall and Anti virus and reboot your Pc.
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t Bluetooth for the Upgrade)
4. When you see usb appear at the bottom of bootloader screen
5. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
After then, install origial ROM. (u can try T-Mobile MDA Software Version (2.26.10.2) )
Let me know if it's working
ty man for ur reply , i have tried every possible solution, including mtty! no luck. from ur post i didnt understand the following
Go online and find botton run , update utility 2.00.1
Click to expand...
Click to collapse
did u mean button rom . if yes , what the 'update utility 2.00.1' ?
ty
can i use mtty to revive my phone? i found some command for erasing my entire rom in the phone , but it doesnt seem to work . help me
Hello XDA Nice Team !
By mistaken i wrote some file to my bootloader in my I-Mate Jam ..
That was after using the bad ROM : 2.03
it's the worst cooked version i saw !
Now my bootloader mode is working .. but no way to connect to PC with USB port ..
My computer does not recognize my Magican when plugged in bootloader mode anymore!
Bootloader Ver: 1.0
is there any way to fix or upgrade or restore original bootloader
Now i cant upgrade or downgrade my magican by any method
Noway to use successful connection with any roomupdate utility
Please help me to fix or restore my bootloader!
Thanks to any one read or replay or try to help or help me to resolve my problem
XDA lover
i'm sorry that happened mate...
i've had success with flash-from-bootloader attempts before, both on my Magician, when i accidentally flashed off of Vista and it'd enter the bootloader every week or on a reset using the reset hole, and also on my Wizard when i ignored warnings from WM5torage and it'd only enter the bootloader
what precisely happens when you connect to the PC, allow USB connections in AS/MDC, and let the phone enter bootloader however it does? i can just flash a rom from there, but i won't (iirc) get any reports of as recognising the device...
My experience:
1- when i plug my sd card into my jam .. usb not recognized in bootloader mood !!
2- when i use puty or roomupdate it reaches to USB> then when i type any command it does not respond !
3- i could do something .. i let my phone bootup and this i-mate logon screen stays 4ever .. i connected my ppc to pc and i could explre my imate by activesync ...
i could reach something .. when i explore my phone and remove everything from startup folder .. my phone boots .. and i can see start botton .. no touch alignment comes .. and everything works .. but.. screen is virtually reversed .. i can see the OK botton but i must click on the facing area and it be clicked ..
i think i executed some wrong hard SPL to my phone ant that happened >
is there any way to resolve this problem?
is there any way to erase flash on my I-Mate Jam????
is there any way flash my phone?
i also have prepaid JAFWM with pkey and USB cable .. no BOX ..
Help please!
that's messed up... howsabout flashing it at the point when the phone boots up? if there's an AS connection there, then it may work... i'd flash to an official rom though
Same problem , PLS Help !!!
Thx for help
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
If your magician isn't detected at ALL by your PC when plugging the USB cable into it (i mean, no new hardware; no unrecognized hardware; nothing is detected in your PC when you plug the USB cable), and unless you had previously made a SD backup of your entire Flash with this procedure ( http://wiki.xda-developers.com/index.php?pagename=MagicianSDflash ), then your only option will be to build a JTAG diag cable:
Here are some general directions / ideias:
Magician JTAG pinout: http://wiki.xda-developers.com/index.php?pagename=MagicianJTAG
How to build/run the JTAG: http://wiki.xda-developers.com/index.php?pagename=DeadBoot
Photos : http://www.cf-box.com/htm_data/55/0912/1679.html
Some interesting stuff for debugging problems: http://pda2u.ru/ptopic205.html
For sure cotulla has one built so to test his ROMs + bootloader - maybe he will be willing to give you some directions if you run into problems, and above all, give you a prepared .nb0 (with the bootloader file) for your magician, which i do not know if there's one out there, extracted from an original ROM.
Anyway, you can always try and do it for yourself using itsme utilities. Follow this link: http://forum.xda-developers.com/showthread.php?t=218643
Regards
Keeper,you're awesome! I'm searching for JTAG,too
xiaojin1985 said:
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
Click to expand...
Click to collapse
Dear xiaojin1985 ,
Thx for your help, But unfortunately i tried your solution but it dosnt work !
Dear Keeper,
Thanks too for your help,
and i think the solution for my problem is one of the solutions you says ( How to build/run the JTAG: ) ,
but the pictures is not available anymore , so pls can you get the pictures ?
All the pictures are in here:
http://s218.photobucket.com/albums/cc23/alex_beda/ and in attachment there's a .mth file with all the pics built-in.
Don't take it wrong what i'm about to say, but in all honesty if you can't figure this out yourself (digging up the internet for the missing pics), i would suggest that you shouldn't try this, since this ain't easy at ALL...
Just to give you some ideias, it will require you to adapt your magician test point signals (TDO;TDI; nRESET; etc,)seen on the magician pinout pic to what is said; solder very thin wires (best done with a small hot air tip); fixate the small dip switch (micro switch) to be always on; keep the USB connected...idk... plus alot of other small details which ain't easy to accomplish.
Personally i haven't tried this yet but for sure it would work
If you decide to go ahead, please post some results!
Connection error solution
this is my problem
hi all. A friend of mine gave me an S100, and after i played for a few days with it, i decided to update it's rom. A "country error" problem appeared,cause i have the greek version, so i ran MaUpgradeUt_noID.exe which completed (as showed 100% process). My (new) problem is that i cannot update anymore. Every time i enter boot menu, i ran the upgrade
(HTCMAG_ROM_WWE_O2.rar) following all the steps normally. When the device resets (so the upgrade is going to start), it's re-reseting again and showing ERROR 101 connection error. Any ideas?
Qtek Greek version
R 1.12.00
G 1337.42
D 1.12.00 WWE
P.S. apart the problem everything is function properly
and the solution
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe radio_1.11_greek but idont reset the qtek in first screen
and upgrate downgrate start all ok
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe MagicianRadio_1.12.10. uk but idont reset the qteki n first screen
upgrate from radio 1.11 to 1.12.10
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run HTCMAG_ROM_WWE_O5_251209
everything is ok my magisian run the new Rom
here..........................
very newbie, help me please. i download magician radio, unzip it and copy it to my mini. knowing nothing, i press the enterBL.exe now my mini always in kinda bootloader state, dark screen and written serial v1.00 what should i do to get my mini back T_T help me please
Did you try resetting the device? (pushing the small button next to the headphones plug with the stylus)
thats the first thing i did, nope nothing
You should not copy it to your device...
Just hold Camera+Power+Reset,enter to SerialUSB Mode,connect it to PC with USB wire,run update.exe.
yes thank you all, now i have the WM 6.1 hehehehe ^_^