hi
when i write with ntrw the rom imge in the sd card it shows me it was writen bat nothing is on the sd card ..when put in pda in bootloader mode nothing happening.just show serial v1.02..what is the problem...
thanks
i find the problem
i find the problem
How did you solve the problem?
re
.don't have to format the sd card after romupgrade just write with ntrw the rom image without format .
Related
SD Card problems after upgrading to 1.12
I posted this in the normal form but no one replied, I think this may be a problem causing my upgrading, so I post again here
--------------------------------------------------------------------------------
The SD Card used for dumping rom with ntrw could no longer be accessed by my notebook which was accessable before(I formatted the SDs already with my mini), it needed to be formatted, after I did that, and plug the SD into my mini, the mini couldnt read it and prompting the SD card needed to be formatted again!
So, I formatted it again with my mini, but after that my Notebook want to format the SD again, and the fight between them keeps going...
anyone encounter the same issue...there are some clues that I tested:
1. I got 3 SD cards, 2 for them used for upgrading and they occured the same problem, but the third one which is clean can be accessed by both machine
2. The SD cards(those with the problem) can be read by my PC's Card reader...
I know I could use the card reader instead, but I dont wana waste the build in one in my notebook and the data exchange between my Notebook and mini is quite important to me, pls if anyone could help me solving the problem, Many thx!
Hi, you must use ntrw in comand window ( in winxp run cmd )
Take ntrw.exe and your file.nb1 in roof directory.
Type the command C:\ntrw read rom.nb1 x: ("x" is your cardreader name)
Ignore any error message when you plug SD card into your cardreader.
After that you type d2s in next window, so on...
When finish you will have file .nb1 in your roof directory.
Hope you successful !
hi guys
ive got a problem with my sd card.
it keeps on asking me to format it on my pc and xda but is unable to complete the formatting process, therefore i can not use the card.
its showing memory are 241kb remaining but there are no visible files on the card. ive used "format flash" and "pocket mechanic" to try and format the card but they are unable to see the card on the xda.
ive also used some software to see the deleted items on the card and yes there are some files..
how do i delete these as i think they are causing the problem.
thank you for any help
jav
sorry that should have read 241mb
also ive just tried the panasonic formatting tool and it keeps on saying its write protected when i can clearly see it isnt........
help
sometimes they just die for no reason
try another sdcard
try the card in other devices which use sd cards
Hi,
I have a prophet,my device seems like dead during bad update, not it stucks on bootloader, but when connecting to USB, device hangs,and computer doesn't recognize it, seems the part of the bootloader that help device recognizes itself to usb is broken...
PLZ someone help me,
all i need is a flash SD card image some of guys can take an image from Flash SD card and sent it to me or upload to rapidshare or something... and then i can flash my device with flash sd card...
PLZ help me
Thanx...
Hi I have got s200 and S Card.How Do You install Sd card image file and How Do I Can Create Sd Card image file
QtekS200tr said:
Hi I have got s200 and S Card.How Do You install Sd card image file and How Do I Can Create Sd Card image file
Click to expand...
Click to collapse
is ur device G3 or G4 ? i need G4 sd card image
u can download this software
ftp://xda:[email protected]//Uploads/Prophet/Prophet-tools/TeraTermPro_WinCE_USB.zip
* Get into the tri-color screen (bootloader) (hold CAMERA, reset) and plug into the USB port.
* Kill wcescomm.exe from Windows XP using the Task Manager (CTRL-ALT-DELETE) (this is the ActiveSync driver for the USB port)
* Start Tera Term
* Selec the "serial" radio button and from the drop down list select "USB"
* Hit "return" to ensure you have a command prompt.
* Make sure your 128MB SD card is in the slot.
* Type "r2sd all" and hit return.
then download this software
http://rapidshare.com/files/220968581/XDArit.exe.html
connect that SD card to ur pc's card reader,don't try to open it with my computer, cause it doesn't contain any files or folders...and also File System,if u try to open,ur computer will tell u to format it or not !
open the software, choose the drive belongs to ur memory card from the droplist...
in bottom of the window click read from SD ... another window will be appeared, select both Bootloader and Windows CE ... this will give u 2 file ... save them, upload them to rapidshare or megaupload ...
that's it
i make it and i tested and work but i cant read sd card to extract 2 files i don´t know why.
sorry for my english
My USB Mini port seems to be damaged. I can charge the phone but when i connect it to my PC, the orange light lits and the phone gets charged but it is not found by my pc. So pls let me know how can i upgrade to wm 6.1 through sd card flash.
The solution is:
U need
ntrw ftp://xda:[email protected]/Magician/Tools/Backup_tools1/ntrw.exe
wm6.1 nb1 file http://www.mediafire.com/?sharekey=02c513f13b6fba677f7ec40ada4772a6e04e75f6e8ebb871
If the 1st method doesnot work then u need the backup of existing rom Click here to know how to back up ur exsiting rom http://wiki.xda-developers.com/index.php?pagename=BackupExistingRom
the hex editor http://www.hhdsoftware.com/Download/free-hex-editor-neo.exe
Method 1:
write to the sd card using
ntrw write Cotulla6.1.O3.nb1 F:
F: is ur sd card drive
There will be an error saying parameter incorrect. dont worry. Insert the card into the phone and enter the bootloader( Power+Camera+ SOft reset). A message will come asking you to press power button to flash. Press the power button and wait for complete flashing. in the end there will be a error that checksum failed . dont worry and do soft reset. Hurray u now have wm6.1 on ur magician.
Method 2:
If this doesn't work try this.( U should have a backup copy of ur old rom nb1 file.)
copy the first 416 bytes of ur old rom to the 416 bytes of the rom downloaded using hex editor
write the new rom to the sd card and install as in method 1.
It's not possible to install my rom via SD card.
Sorry, it designed for RUU flashing only.
I was wondering this myself...
Are you sure, Cotulla, that following this procedure would fail with your ROM?
Please someone try and if sucessful pls upload the .nb1 file so that i can write it to SD card and flash it through SD card. Thank you in adavnce
I can dump my ROM for you if you're willing to test to flash it.
please. i will try on my o2. thanks
Here it comes: click. Password is xda-developers.com.
the file appears to be too small only 23 mb . coutulla's rom was somewhere around 50 mb. will this work. i will try tomorrow as i am outside & donot have pc access
That's because of compression, the file itself is 63.7 MB.
I was planning to try this as well, but I don't have a memory card at the moment.
Keep us posted and good luck
As MusikMonk stated, this file is compressed and crypted with 7z. Haven't you heard of 7z yet? It's about time!
I doubt it will brick your Magician, since it's not overwriting the bootloader. Thus you can always flash you beloved old ROM.
While writing the file to the memeory card i am getting this as output.
NTRW v2.00
Removeable media
Cylinders: 0:120
TracksPerCylinder: 255
SectorsPerTrack: 63
BytesPerSector: 512
bufsize is 65536
WriteFile(): Cotulla6.1.03.nb1 -- the Parameter is incorrect
When i put the memmory card in my PDA and enter the bootloader mode only the screen with Serial and v.1.02 is there and there is no option to install press power button.
You must have done something wrong when filling your SD card.
I get that "press power to flash" message.
I hope someone will eventually try to flash that file... otherwise I made a lot of effort for nothing :-(
So does it work or not???
I used 1 GB Memory card. The Problem Might be because of than. Pls Letme know what memory card u used. Shold I used 64/128 MD card instead of 1 GB. Pls Help
64MB is a few bytes too small, 128MB is sufficient. I used a 256MB card... maybe the boot loader is unable to read much bigger cards... if my 16 GB card were empty I could give it a try... ;-)
I tried to copy the Cotulla.nb1 file on my SD-card, but it doesn't work. I used a 2gb and 128mb card...
I copied the ntrw.exe and the Cotulla.nb1-file to c://user/username. Then I write "ntrw write Cotulla.nb1 j:" in the black DOS-Window and press enter. j: is my SD-card.
Now there appeare some lines of text and I can wait about 3 minutes until there comes something about a wrong parameter...
But as I understand it, this should be no problem.
But the problem is when I try to take a look on the SD-card, there comes a window, that says that I must format the card. I cant open it... When I take out the card from the card reader and put it inside again, I can see what is inside on the card. But there is only one folder with the size of only about 130kb and no ROM...
My OS is Vista.
What am I doing wrong???
Magician boot loader does not expect any file system on the SD card, thus ntrw writes the OS directly to the first sectors of your card. When you insert this card now anywhere Windows does not find any file system and recommends to format. That is correct (as long as don't answer yes) and shows writing WM6.1 was successful (given your card is big enough and failure free).
To make clear: you shouldn't be to browse that card in Explorer when you wrote WM6.1 on it.
Ok but if I put the card out of the reader und back again I can browse the card and there is nothing except of an 130kb small folder...
And if I put the card into my magician on bootloader, nothing happens...
What could be the reason for that?
I tried with 256 MB memory card I am gettin gthe same message while writing to card.
NTRW v2.00
Removeable media
Cylinders: 0:120
TracksPerCylinder: 255
SectorsPerTrack: 63
BytesPerSector: 512
bufsize is 65536
WriteFile(): Cotulla6.1.03.nb1 -- the Parameter is incorrect
And when I enter the bootloader mode with the card Inserted I get the message:
SD Download
==========
Sections=1
Not allow
update!
But with the same SD card when i write my old ROM( whic i had backed up) I get no error and when I insert the card and enter Bootloader mode I get the message :
SD Download
==========
Sections=1
Press Power to Flash
This means that there is some problem with the nb1 file . So kindly someone try it and post the results
one more thing. The backup.nb1 which i backed up from my sd card is 243 mb big. So i feel that the nb1 file which U extract from your card should also of around the same size and not 65 MB. Correct me if i am wrong.
I tried to extract nb1 file after writing ur rom to my sd card. it is also 243 mb big.
Hi guys,
I hope this is the right section to post this issue.
Does anyone have a solution to completely erasing data from a sd card, my problem with my sd card is that i am not able to delete files from the card or add any new files. I am able to copy files from the sd card to the pc though. I have tried formating it on various computer operating systems as well as on an android system.
What i get is the format completes but after reconnecting the card to the pc or phone, all the files that were previously on the card have somehow returned and the files are not corrupt or anything because i am able to view images and play music from the sd card. Is there any method I could use or is it time to let the memory card go?
Check for Errors
Try check your SD card for errors on the computer (Mount it first).
JBmorris said:
Try check your SD card for errors on the computer (Mount it first).
Click to expand...
Click to collapse
Hi JBMorris, i have tried mounting it to the computer still no luck, I used a program called active kill disk to format it and check for errors but the program freezes on the verify and checking for errors section. I think something about the sectors not being readable so I might as well get a new sd card and thanks for the suggestion!
JazzedMontage said:
Hi guys,
I hope this is the right section to post this issue.
Does anyone have a solution to completely erasing data from a sd card, my problem with my sd card is that i am not able to delete files from the card or add any new files. I am able to copy files from the sd card to the pc though. I have tried formating it on various computer operating systems as well as on an android system.
What i get is the format completes but after reconnecting the card to the pc or phone, all the files that were previously on the card have somehow returned and the files are not corrupt or anything because i am able to view images and play music from the sd card. Is there any method I could use or is it time to let the memory card go?
Click to expand...
Click to collapse
use a external card reader and then try to format
if not then use a software utility " low level format "
try if it helps
singh_aman said:
use a external card reader and then try to format
if not then use a software utility " low level format "
try if it helps
Click to expand...
Click to collapse
Hi Singh, i tried using a software utility also tried the windows disk management and I'm still stuck with the same problem.I have decided to get a new card as my apps are not able to write to the sd card. Thanks for the help.
JazzedMontage said:
Hi guys,
I hope this is the right section to post this issue.
Does anyone have a solution to completely erasing data from a sd card, my problem with my sd card is that i am not able to delete files from the card or add any new files. I am able to copy files from the sd card to the pc though. I have tried formating it on various computer operating systems as well as on an android system.
What i get is the format completes but after reconnecting the card to the pc or phone, all the files that were previously on the card have somehow returned and the files are not corrupt or anything because i am able to view images and play music from the sd card. Is there any method I could use or is it time to let the memory card go?
Click to expand...
Click to collapse
I think you had encrypted it with some device before.... So if you insert in that device and remove encryption...
But if you have factory reset your device and remove encryption key.. Then it will be very hard (may be impossible) to format it or change permissions
Hit thank button if this post helped you
Killwish said:
I think you had encrypted it with some device before.... So if you insert in that device and remove encryption...
But if you have factory reset your device and remove encryption key.. Then it will be very hard (may be impossible) to format it or change permissions
Hit thank button if this post helped you
Click to expand...
Click to collapse
Hi killwish, that makes sense it is possible it was encrypted before as i used a different rom, so would you advice me to install the previous rom and try to format it?
JazzedMontage said:
Hi killwish, that makes sense it is possible it was encrypted before as i used a different rom, so would you advice me to install the previous rom and try to format it?
Click to expand...
Click to collapse
Bro you have flashed new rom... And encryption key is deleted.... So now I think it is impossible to do what you want....
May be some hacker will help you... Wait if someone give you the solution
now you have only 1 option left
try replacing it from service centre for free
singh_aman said:
now you have only 1 option left
try replacing it from service centre for free
Click to expand...
Click to collapse
Oh.. Yeah it is the solution.. If your card is in warranty
You should format your SD card through CMD
To format a memory card from command prompt, follow the below procedure:
Connect the memory card to your PC through card reader.
Click on Start > Run > Type CMD and click on OK.
Assuming the letter of the memory card drive is G.
Now enter this command.
format /q /x G: and press Enter.
Note: Don't forget to replace the letter "G" with your drive letter.
snehashish93 said:
You should format your SD card through CMD
To format a memory card from command prompt, follow the below procedure:
Connect the memory card to your PC through card reader.
Click on Start > Run > Type CMD and click on OK.
Assuming the letter of the memory card drive is G.
Now enter this command.
format /q /x G: and press Enter.
Note: Don't forget to replace the letter "G" with your drive letter.
Click to expand...
Click to collapse
I think it will also not work
Hit thank button if this post helped you
snehashish93 said:
You should format your SD card through CMD
To format a memory card from command prompt, follow the below procedure:
Connect the memory card to your PC through card reader.
Click on Start > Run > Type CMD and click on OK.
Assuming the letter of the memory card drive is G.
Now enter this command.
format /q /x G: and press Enter.
Note: Don't forget to replace the letter "G" with your drive letter.
Click to expand...
Click to collapse
Hi Snehashish, i have tried using the cmd and get an "access denied error" even though i am using cmd with administrator rights. It seems to me there's nothing i can do as i have tried formatting using different methods.
Replacing Card
Hi guys,
Thanks for all the effort, my card doesn't have warranty and I will be replacing it, what I have learned from all this is to stay clear of encryption if you not sure of what it fully entails!
Cheers Fellas!