Hi all,
Have purchased a German MDA_C and flashed it to the latest dutch WWE rom (1.13). I use the NOID updater and get an error message at 99% of the update.
After this my MDA hangs at the splash screen (but showing updated rom and radio versions).
Doing a lot of soft and hard resets I managed to get by the splash screen 1 time...
Tried a lot of different rom versions but each time I get the same problem
I've read that the SPLASH screen problem is more or less common but I wasn't able to find a solution on the forum.
Now I made one stupid mistake... I did not backup the original rom...
Any suggestions how to get up and running?
Thanks in advance...
BuDDaH
The very first boot takes a long time, 15 mins for some! If you're not waiting for around 15 mins ....
Thanks for this valuable information kta.
This time I waited 1 hour after upgrading just to be sure.
same result. flashing stops at 99% of the CE Rom.
Hard reset shows splash screen with version numbers (radio 1.13 rom 1.13 wwe) and then just hangs.
From bad to worse
So I had a MDA_C that did not boot further than the splash screen.
Updated using the MaUpgradeUt_noID.exe. Thought I'd give the SD way a try since I already tried about 6 different roms all with the same result.
First I made a backup to SD card of what was in my MDA using romupdate.exe
extracted the file to my HD.
After extracting (and securing the device ID) I tried rebooting my MDA.
Now things got worse!!! instead of the splashscreen I now have the BLACK SCREEN......
Have tried resetting and hard resetting dozens of times (more like a thousand times) and only occasionaly the splash screen comes up. :roll:
But over the last couple of days I only managed to get the bootloader 1 time (and at that time there was no SD card inside) :shock:
this is behaviour I haven't read about on the forum.
Guess I will have to get it serviced.
Is there anyone on the board that has an address in the Netherlands that can flash or repair my mda? Not sure T-Mobile NL services German devices...
Thanks!
Not dead yet?
Here's some more info.
My 'almost dead' Magician is showing signs of life.
I had the BLACK SCREEN.... (first couple of lines of pixels were not black)
After thousands of hard and soft resets (soft resets seemed to have the best results) I managed to get into the bootloader!! Flashed with an older rom and at least I'm getting the splash screen again. (but still getting an error at 99% of update of the CE rom).
I'm updating using the exe in bootloader mode btw....
Since there's always an error at 99% when I use the exe method and the device is not booting I thought about giving the SD method a shot.
My device didn's show the SD option but fortunately tadzio explained about the MBR (didn't even know a SD card had one!!! :lol:
http://forum.xda-developers.com/viewtopic.php?t=32849
When I decode a nbf file using nbfdec.exe and flashing afterwards I get a message that my ROM is to small.
Size is same as nbf file.
How do I correctly decode a nbf file?
Thanks for the help.
BuDDaH
Don't use a nbf, get a dumped or bs rom from the ftp & follow instructions with copying bytes etc.
M
Ok OLTP I'll skip the nbf decoding route.
Think one of the problems is the way the newer roms are encoded.....
Saw you're using a 1.13 bigstorage rom?
That one is not on the ftp is it?
Modified your own rom image?
Hi BuDDaH,
I downloaded at the Dutch TMO site the shipped-rom, unzipped the exe file & decoded the nk.nbf nbfdec. In this nk.nb1 I altered the usual BS bit patterns and re-encoded the nk.nb1, again with nbfdec, to the nk.nbf. After that it was just running, the extracted, upgrade program & it worked like the usual shipped-rom upgrade. you might have to use the maupgrade_noid version, sometimes twice.
This method is better described in the thread about upgrading to radio 1.13 which you can add along the road as well.
So yes I made it myself, not so fond of using other people's rom unless I have to. Please don't let anyone be offended by this, cause a replaced bit can cause serious harm, like I encountered myself, with my own corrupted rom-dump.
Good luck, M
Just wanted to update you all on the latest status.
I managed to flash a german rom (as I've got a German device) although I always get an error message at 99%.....
Fist it just stuck on the splash screen but this somehow deteriorated. Now I get a black screen covering about 5/6th of the screen. the first 1/6th shows a part of the splash screen. No backlight and it hangs.
No more bootloader so I need to have it serviced (anybody knows what the techies do with such a device?)....
Now the question remains where.
T-Mobile NL refuses to service it since the IMEI is unknown to their system
T-mobile Germany doesn't have a service center but only takes repairs through a T-Punkt shop..
Any ideas?
Thanks,
BuDDaH
Latest update...
I sent it in for repair and it turns out that the ROM is damaged and the phone needs a mainboard replacement..... which costs about the same as a new unit...
Anyone got a spare one laying around for me?
So much for my Magician!
Cheers,
BuDDaH....
Sorry to hear...did you try another SD card?
Yep I did; but unfotunately the situation deteriorated and I'm completely unable to get into bootloader mode.....
Well.. :idea: maybe I must see this as a great opportunity to get wild with a set of scewdrivers
Hey BuddaH,
There enough people interested in the parts here at the forum, so there's a tiny brightside on your adventure :-(, man i do feel sorry for you.
Regards, M
Yup, i need some parts also
BuDDaH said:
Yep I did; but unfotunately the situation deteriorated and I'm completely unable to get into bootloader mode.....
Well.. :idea: maybe I must see this as a great opportunity to get wild with a set of scewdrivers
Click to expand...
Click to collapse
You probably ran the battery down. I don't think it charges unless the ROM is working. That is why it is highly recommended that you start with a full charge before commencing a ROM update.
Hi Stevedebbi,
Even in my situation the it still seemed possible to charge the battery (at least the red light went out and the battery got hot).
Sent my device to apexlaptops.co.uk cause they claimed they reflash...
Got the reply back that they couldn't get it too bootloader mode and were unable to repair. (guess they could not do some JTAG debugging).
I may be able to buy a working device that's damaged on the outside....
Related
I think i must have the worst luck or else I'm doing something stupidily wrong...
I fried my device when trying to apply the bigstorage hack on ROM version 1.12WWE.
A week later my mate asked me to do the same on his JAM- same thing again- device just totally fried!
I had successfully applied the bigstorage hack on both the above devices with the original T-Mobile Rom (1.01 or something)- this went without a single hitch.
The method I used was using the 'Bigstorage software'
Do i need overwite the first 416 bytes even if im using my own rom and not a downloaded one?
What am I doing wrong?? This has really got me frustrated now.
Any insight as to what I could be doing wrong would be very much appreciated.
Thanks
Quite a few people have reported to get a totally "dead" magician using the "Make BigStorage" method. The good news is that when they return the machine to the service center, it can be fixed.
This is different from the "stuck at bootloader or splash screen" cases, which can be easily recovered by the user without the need to return it for repair.
It is much more safe to use the "edit two bytes at two locations" method to get BigStorage.
Talents- I was guessing that it would be you to reply- much appreciated for that . I was/am 99.9% confident that the service centre would get it working again. My frustrastion comes from figuring out what I am doing wrong. I am stumbled even with professional background (IT/PCs!).
So is it just my worst luck- or could I have done something wrong, unknowningly?
As much I want the latest ROM and bigstorage- i dont think i can run that risk again- even with the 'two bytes' method.
P.S. I was using a 128MB SD to perform hack- surely this is enough?
I recently did the bigrom hack, and had the same problem. after the device took the hacked rom, i soft reset, and it stayed on the boot screen for 25 mins.
I re-flashed the original non edited dumped rom to the device and it worked, copied the hacked rom to the card, and tried to flash again....and it worked.
My heart stopped when i just hung on the boot logo originaly.
Imp
Impossible,
From what I can gather the problem that you had is (was) not fatal... when I performed the bigstorage hack the device was TRUELY dead- nothing showing on the screen whatsoever... as Talents has also mentioned.
Anyway I had it sent off to the repair centre and have a brand new JAM back. Performed the 'two bytes' bigstorage method (thanks to Talents) and all is running well
Glad you didnt loose will in the upgrade.
Where abouts did you have to send your dead handset to, how long did it take to get a replacement.
Imp
In the end performing the upgrade was purely for the fact of doing it for the sake of it and frustration.
My original JAM was only about 2 and bit months old so it was still under warranty- returned to the place of purchase- T-mobile centre.
My one took 8 working days for me to get back but my mate's one took only 3 days.
Hello,
I experience same trouble as u all, still wasn't able to get the big storage to work. Let me tell u what I already tried:
Had a good working Dutch Orange M500 device with 1.06 original ROM. Udated it to 1.11 WWE I-mate ROM, no prob. Opend the storagespace with the mksBigStorage method, no problem,had 27MB free.
Updated to latest 1.12 original new Orange ROM via USB-cable method, no problem.
Now I want to open bigstorage on this original Orange 1.12 ROM, and no matter what I try, I cant get it to work.
-Tried yesterday all day, got a backup from CLEAN Orange 1.12 ROM, edited it with mksbigstorage program, no success at all. Got through all the steps, it goes to 100 %, checksum fale, upgrade fail message. Now it is stuck in bootloader mode.
-Edited original clean ROM with "edit two bytes at two locations" method, got through all the steps, it goes to 100 %, checksum fale, upgrade fail message. Again stuck in bootloader mode. Funny thing was that when I edited the rom, I only found 1 location in the ROM to edit, not 2. Went through it with the following query in the Bytes field: 02 00 00 80 00 20.
Maybe this is my mistake? Anyhow:
- got an external reader today, after trying all day yesterday with internal reader. Doesn't seem to make any difference, no matter what method, still no big storage. Did the whole process again, both metods. No luck until now. WHAT AM I DOING WRONG???
Yoho, I did it! It turns out that my 128 MB SD-card is giving me trouble, when I used the 512 card it finally worked!!
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Drunknasty said:
I am a little confused. I have been trying to get WM6 on my T-mobile Wizard and actually got TNT 1.1 loaded and was working fine. I found that I could no longer view my contacts. The page would appear and then as quickly as it appeared it disappeared.
So I figured, I at least got it this far. I will just reload this rom and see if perhaps something did load right. Well after the reload. The phone boots up to the splash screen with IPL\SPL numbers and just sits. NOTHING.
I left it there for like 2 hours and still nothing. But I can still get into the BootLoader.
My questions to you gurus is:
Is the phone fubared?
Can I do some kind of master reset?
Why would it tell me "Invalid Vendor ID" when trying to flash the orginal T-mobile rom?
Are there any tools that can help me out? Paid\free?
Please help!!! Seriously! Please HELP!!!
Very much appreciated.
Thanks
Click to expand...
Click to collapse
if your device is G3, unlocking is required to flash any rom, before upgrade your device, it is recommended to flash an official WM5.0 rom (in your case T-Mobile rom) with IPL and SPL 2.xx then flash again.
in general there are many probabilities for your issue.
((Where is TNT1.1?? did you mean 1.0?? ))
My Bad meant 1.0
So to get it straight.... I will need to unlock my phone each time?
Oh and to correct myself again, when flashing with the T-mobile ROM it says UPGRADE ONLY. And the read me file says its the wrong RUU. But it is the same file from Tmobile I used when I first got the phone. But I will try again.
Are there any other suggestions?
You need to read the "how to flash" sticky.
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Try another ROM.
Sounds like you need the "Wizard Love" rom. I dont have the link handy but I am sure someone else does.
Drunknasty said:
I did. I am not any expert or anything but I believe the phone is unlocked already since I once had WM6 on my phone. The real issue I am having is that it wont boot past the splash screen after flashing.
And that is true when re following the steps in guide. After flashing to the button rom it will not boot past the splash screen.
Click to expand...
Click to collapse
Already got it. Thanks I am trying to load it now. But the only thing is that the last time it failed and I can understand what the error says. I know the number is 300 but can read the language.
But I will let you guys know when this load completes.
Thanks again for all the assistance.
No worky worky. The load completed and then boots the splash screen shows and then stays there.
Any ideas?
Try to remove the battery and let it out for at least half an hour. Then put it back in and see what it does then.
I thought the same thing too. So when it got done last night, out of frustration, I removed the battery and left it there to wait on when I get off work today. I will report back on what happens.
Again I would like to thank you guys for helping me. I really do appreciate it!
STEP 1 install the original manufacturer ROM
T-mobile UK
http://www.tm-phonedownloads.com/download_manager_mda_vario.html
T-mobile US
http://www.t-mobile.com/wmupgrade/
Search for the original rom for any other
instructions on how to use the original rom can be found here
http://support.t-mobile.com/knowbase/root/public/tm23294.htm?&A2L.SERVICE=AboutUpgrading
Put it in the bootloader mode.. ( three color screens )
hope this helps..
cheers
Praneet
Ok I did that and it gave me ERROR 296: UPGRADE ONLY
Then it tells me that the NBF file cannot be used for my PDA Phone. Please get newer NBF file.
Is there any way I can get the Tmobile splash and IPL\SPL number back to original, it doesnt need to boot all the way into WCE but atleast show the same numbers and splash during boot up?
Or any other way to get this thing to work?
Thanks guys
BTW it is a HTC Wizard from T-mobile.
If you are getting an error 300 you need a newer rom update utility, and regardless if your phone is a G3 or G4 it needs to be unlocked before you flash any rom.. LOAD a OFFICIAL cingular ROM onto your device before going any further, then unlock your phone either via www.imei-check.com or through some of the tools offered here...
Which one should I down load from Cingular? Even though I have a Tmobile phone?
what ipl and spl are you using and what radio are you using. Just post all the numbers from the bootloader
As soon as I get home, I will post them.
Thanks
Ipl 1.01
Spl 3.08
Thanks
Drunknasty said:
Ipl 1.01
Spl 3.08
Thanks
Click to expand...
Click to collapse
uh oh. someone tell me if I'm wrong, but I think this is bad. it's the result of flashing a g4 with g3 or the other way around... keep searching, and good luck.
flash the original t-mobile rom. your phone doesn't appear to be unlocked. good luck
Hi,
Was changing the ROM on my Kaiser, using JUMPspl as I had got the white screen using Hardspl. During the upgrade got an error at about 18%, went through the recovery procedure only to get back to the Bootloader screen with the screen saying
SPL-1.93.0000
I think it should say something different here!
At the moment can only get the the tri-colour bootloader screen with usb at the bottom.
Please any help would be much appreaciated.
Thanks
If you are at the tri-color bootloader screen, reflash a ROM.
that's where the process starts at anyhow,the bootscreen.
But doesn't the SPL have to be either Hardspl or jumpSPL.
I have tried to do the rom update again but sticks on 0% and gives error 262
Alemaker said:
If you are at the tri-color bootloader screen, reflash a ROM.
that's where the process starts at anyhow,the bootscreen.
Click to expand...
Click to collapse
Not advisable if he has the default SPL still though which by the number appearing at the tri col screen it appears to be the case.
Try doing a hard reset and see if it boots into the original ROM then at least you will find out if it is bricked or not, however, i'm not sure it will work based on the fact you got part way through in the first place.
Hold down the keys directly next to the Send and End (green and Red) Hold in the stylus and keep them all held untill you get a screen telling you to press the green (send) key.
Tried the hard reset, takes me back into the bootloader. Any other ideas?
Hmm... ok then.... you are pretty much looking at a very expensive paperweight at this moment in time then.
Look at this thread...it "may" (i'm not promising anything but it may point you in the right direction) help you out. Let us know how it goes.
http://forum.xda-developers.com/showthread.php?t=361612&highlight=bricked
cmcmill01 said:
Hi,
Was changing the ROM on my Kaiser, using JUMPspl as I had got the white screen using Hardspl. During the upgrade got an error at about 18%, went through the recovery procedure only to get back to the Bootloader screen with the screen saying
SPL-1.93.0000
I think it should say something different here!
At the moment can only get the the tri-colour bootloader screen with usb at the bottom.
Please any help would be much appreaciated.
Thanks
Click to expand...
Click to collapse
Hate to joint the parade, but the exact same thing happened here - 18% now stuck at 1.93.0000
For anyone else reading this BEFORE flashing a new ROM please read, read and read again EVERYTHING related to flashing on this site, wikis and wherever else you can get info.
Another idea for you. Search around here for how to flash from an SD card that may solve the issue out for you. As previously noted though....READ READ READ and be 110% certain you understand what you are doing before you do anything.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=stuck+bootloader
details some info for a Wizard, should it be the same for a Kaiser?
Will Mtty get me any further?
MTTY will at least give you a USB connection to the device it is worth a shot given your current situation.
There is hope!
I did a clean reboot of my PC and disabled my antivirus (avast) and was able to sucessfully reflash the new 1.62 rom (released from ATT site today).
Thanks will try the new 1.62 rom.
What commands can you use with MTTY?
tried the At&t rom gives me an error on the vendor id. Will try a HTC rom
I have tried multiple roms and they all give me the same error Error 294:Invalid Vender ID
Any ideas
Am starting to get worried because if the misses finds out that I have bricked the new phone, I am up to my neck i it.
If you are stuck in boot loader & would like some help via MSN Messenger, please PM me or look for me on MSM messenger at [email protected]. I will be available to help later this evening or tomorrow morning.
I have most of the files to fix these issues & can use MSN fileshare folders to help you.
Good chance that you can be up again in a matter of minutes
cmcmill01 said:
I have tried multiple roms and they all give me the same error Error 294:Invalid Vender ID
Any ideas
Am starting to get worried because if the misses finds out that I have bricked the new phone, I am up to my neck i it.
Click to expand...
Click to collapse
Invalid Vendor I.D. is cuz it's locked.
Had the exact issue myself and found a ATT ROM that will boot. It saved me bigtime, so I saved it. It's in one of the posts on one of the threads but I have the actual ROM, it'll overide that lock.- PM me if ya need it.
Got the same solution, Holy S**t about to have a heart attack. Tried nearly ever ROM out there, it was the Asia one that got me going.
Lesson learned: make sure you Hardspl after jumpspl.
Thanks for all the help folks
Glad ya got it fixed. One quick question?
Is your original ROM ATT or HTC ?
It is a HTC ROM. Done My Hardspl and got Sleuth v3.0 on it already
Happy days
Hello guys...
Iam not new, and i have already flashed my first(it was wasted not by my fault)KAISER, it was one year ago and i did it with HARDSLPv1, and lately added some new roms cooked by sakajati(respect)...
Yesterday i bought new one(but one year old) so i tried to flash him as well, i have used HARDSPL 1.93, and then i tried to put Sakajati"s 4th feb ROM, but i come across one big trouble, everytime i try to put it on i encounter the same RUU error:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue. Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
what to do...????
i am very afraid that i destroyed my Kaiser...???
what it means that Wince is destroyed...
Please help me, i am desperate...
Iam not new,
Click to expand...
Click to collapse
But the solution could be found here (search)
If you see the tri color screen everythng is ok, just win mobile is destroyed. Try to flash a rom from your sd card
Thank you very much...
I hope it will work, i really did search for about an hour and tried to put rom on sevral times, but i didnt find nothing 100% secure, i dont want to indanger the unit any more that i did...
thanks again, i will try it tommorow morning at my job, thats where my SD card is...
)))
greganovak said:
Thank you very much...
I hope it will work, i really did search for about an hour and tried to put rom on sevral times, but i didnt find nothing 100% secure, i dont want to indanger the unit any more that i did...
thanks again, i will try it tommorow morning at my job, thats where my SD card is...
)))
Click to expand...
Click to collapse
Part of the problem is that 1.93 is a jump spl and should be used to upgrade to Hard spl 3.29 or 3.56, not as an spl on its own. You need to run jump spl 1.93 from your device and make sure you are connected to your computer, when you see the bootloader you need to unplug your USB, count to 10 and plug your USB back in then flash a hard spl to your phone! Again 1.93 is not a Hard Spl by itself, it is only a middle man to flash a Hard Spl.
I think the best would be to flash a stock rom at first, cause therefore you don't need an other bootloader. Then flash Hardspl (3.29 if you have a kaiser or 3.56 if you have a tilt) and then flash any rom you want
i obviusly have a lot to learn, mate how do I asses if I have TILT or KAISER, what is the main difference...
[email protected]: i have already DL the stock rom before i posted the tread, i hoped on that resolution if there were no answer...
in about 10 hours from now i will get my hands on my tilt/kaiser and hope to arranged the mess i done; I drop by in any case at that time and notify you about condition and my successes...
p.s.:sorry for my poor english...
greganovak said:
i obviusly have a lot to learn, mate how do I asses if I have TILT or KAISER, what is the main difference...
[email protected]: i have already DL the stock rom before i posted the tread, i hoped on that resolution if there were no answer...
in about 10 hours from now i will get my hands on my tilt/kaiser and hope to arranged the mess i done; I drop by in any case at that time and notify you about condition and my successes...
p.s.:sorry for my poor english...
Click to expand...
Click to collapse
It realy doesnt make that much of a difference, I have a tilt and I use 3.29 and I would recomend it to anyone over 3.56 so flash either one, they will both work! And your english is great so no need to say sorry!
greganovak said:
i obviusly have a lot to learn, mate how do I asses if I have TILT or KAISER, what is the main difference...
[email protected]: i have already DL the stock rom before i posted the tread, i hoped on that resolution if there were no answer...
in about 10 hours from now i will get my hands on my tilt/kaiser and hope to arranged the mess i done; I drop by in any case at that time and notify you about condition and my successes...
p.s.:sorry for my poor english...
Click to expand...
Click to collapse
A Tilt is a At$T branded Kaiser, a TyNT II is a HTC branded Kaiser. Tilt has a different keyboard and OEM rom., only differences. People say use 3.56 if you have a Tilt because that is an AT$T Spl, but I use 3.29 on My Tilt and it works great so it doesn't really matter.
hey...
nothing seems to work...
I have tried to put default rom dl from here: http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs but the problem is that it is not bootable from SD, that has to be because the USB conection isnt on (i selected the 3.34.721.2) so i given up that way
Then i flashed the HARD spl 3.29(have kaiser) via SD steb by step first with this instruction: http://forum.xda-developers.com/showthread.php?t=433835; and it dint go through
so i tried with this instruction: http://forum.xda-developers.com/showthread.php?t=420683
it didnt work either, they are the same I know(noticed later);
So problem is that i stuck at WHITE screen that says "LOADING..."
nothig else...???
finally i manage to load/boot the htc rom from xda-wiki site, but i have to chose another one
I have tried to put default rom dl from here: http://wiki.xda-developers.com/index...me=Kaiser_ROMs but the problem is that it is not bootable from SD, that has to be because the USB conection isnt on (i selected the 3.34.721.2) so i given up that way
Click to expand...
Click to collapse
Hey man, nice to see that your device rewakes, you can flash every rom from sd card, simply rename the nbh file to kaisimg.nbh than restart into bootloader and it will automatically take the one from the card
Unfortanly, althought i would like you to be right, you are not. When i tried to do it via SD, i stuck at white screen saying LOADING...(blue) and nothih further... and i tried also the Cmonex_s Hard SPL3.29_SD which also stucks at same screen
So now (after updatig with default rom) that i have basicly normal working device i startet from the top. Using @mskip"[email protected] tutorial called: Flasing your first rom (for noobs); it all goes well, till i start to update RUU(sakajati 4 feb) if it matters, and i tried both (spls 1.56 and 1.93), it stops updatig at 17% and notrhin else then works just puting back the HTC default rom from wikiXDA side(thank god for that)
i am thinking of MTTY, although i dont know what it does guys here almoste all say it fix bad rom flash, but i am not sure if thats my main problem, i rahter think it has something with spls...
if someone has some good advice i will be very grateful...
greganovak said:
Unfortanly, althought i would like you to be right, you are not. When i tried to do it via SD, i stuck at white screen saying LOADING...(blue) and nothih further... and i tried also the Cmonex_s Hard SPL3.29_SD which also stucks at same screen
So now (after updatig with default rom) that i have basicly normal working device i startet from the top. Using @mskip"[email protected] tutorial called: Flasing your first rom (for noobs); it all goes well, till i start to update RUU(sakajati 4 feb) if it matters, and i tried both (spls 1.56 and 1.93), it stops updatig at 17% and notrhin else then works just puting back the HTC default rom from wikiXDA side(thank god for that)
i am thinking of MTTY, although i dont know what it does guys here almoste all say it fix bad rom flash, but i am not sure if thats my main problem, i rahter think it has something with spls...
if someone has some good advice i will be very grateful...
Click to expand...
Click to collapse
Hi,
I couldn´t flash my Kaiser via SD at the first time and tried something that worked.
The SD´s are formatted in Fat16 usually, try to format to Fat32... It seems like a stupid thing, but worked for me.
Reagards and good luck.
SD must be formated FAT32, to work, also I sugest a smal card, 512 or something like that, SHDC usual doesn't work
I have 1GB SD and its not shdc, so thats ok.and i have done it right now, like you two guys said so i formated it with FAT32 but still no succes.
I guess that this tree lines in red/green/blue screen arent right:
KAIS130
SPL-3.02.0000
CPLD-8
i thing this SPL has to da something to do with all this mess a have done
I have flashed a couple of roms( i had three devices) and i flashed a few for my friends and all was OK till now, and i dont know what else to do...
greganovak said:
I have 1GB SD and its not shdc, so thats ok.and i have done it right now, like you two guys said so i formated it with FAT32 but still no succes.
I guess that this tree lines in red/green/blue screen arent right:
KAIS130
SPL-3.02.0000
CPLD-8
i thing this SPL has to da something to do with all this mess a have done
I have flashed a couple of roms( i had three devices) and i flashed a few for my friends and all was OK till now, and i dont know what else to do...
Click to expand...
Click to collapse
Yes, you still have a stock spl on there. It needs to be hard spl'd before you flash anymore. Check out the stickies at the top of the forum.
hi again...
Well, I respect the "rules" of forum, thats why i wouldnt ask for insructions that are already written(thanks for the authors) with that i mean stickys, because i read them, almost all...
But I still tried once again, and I came across the same thing, i stuck at 17% when loading RUU or if i choose the VIA SD i stuck at white screen with blue text saying (LOADING...)...
nothing else helps than loading the dafault ROM by HTC... as i already said once again...
if i manage to solve the problem i will be in touch; what do you thing about MTTY
Edit 1:
i have done everything as it says in the instruction, and just like some of you "replyed" me...
but i always stuck at 17%when loading RUU, when i flash it with SPL 1.56 or 1.93 i never get stuck at white screen it always apeare the mentioned SPLs nimbers and some other text in yellow but when i then load RUUs i stuck at excatly 17% nothing less nothing more
edit 2:
yupi....yupi
i made it...
http://forum.xda-developers.com/showthread.php?t=354061 here is my lifesavior...
those instruction were the one that helped my problem...
it is very nice to ba a part of this community....
First of all please be gentle! I am a complete novice and this is my first post. I have a Touch Pro on a Vodafone contract. I downloaded the recent ROM software upgrade from the Vodafone web site and began the transfer to my phone having followed all the advice. However, the download got stuck at 12% and no matter how many times I start over again it will not go past that point. Worst still the phone is now locked on a red/green/blue/white screen with the message "Upgrade ROM code error Please try again". the error message on the Vodafone software download is No 302. I have tried Vodafone technical help but as I was due for a new phone anyway they have sent me a Touch Pro 2 but don't seem to want to help me resolving the problem with my "old" phone. It is only 5 months old (replacement insurance phone) and in good condition but useless if it can't be made to work.
Can anyone help with simple instructions on how to download a ROM that will work. If not does anyone want to make me an offer for the phone? Currently locked on Vodafone but I am sure you guys out there have the skill to resolve that one.
Many thanks,
Hollybeau
So, they aren't asking you to send it back, I take it? If that's the case, then the first thing I would try would be to flash with the stock rom, if you can find it (not the upgrade that quit on you). If that doesn't work, then just try to flash hard spl. If hard spl goes through ok, you're golden and can flash any raphael rom you want. If it doesn't, the phone is probably toast. You got a new one, so just use the old one as artwork.
Thanks Farmer Ted,
Unfortunately I do not know the orginal stock ROM. It is not on the Vodafone web site and the HTC site keeps telling me that all the likely candidates are "not suitable" ( I assume this is beacuse it is some sort of Vodafone variant). I am afraid that "flash hardspl" means nothing to me - I told you I was a novice! Can you direct me to what and where please.
What bugs me is that here is a phone worth £200? but for a problem caused by Vodafone's buggy software upgrade.
Hollybeau
Start Here.
Best way to find everything you want to know about flashing ROMs.
Lol.
Hard SPL is a bootloader that allows you to flash any rom you want (not just vodaphone). It also has over-write protection, so if you get into the situation you're currently in, the phone won't be bricked. If you can flash it (make sure you flash the gsm version in the raph rom forum), you are fine and dandy.
If you can't find the stock rom online, you may be able to flash the upgraded rom off of your sd card (I believe this will work with a stock rom and stock spl, but am not 100% sure). Re-name the .nbh image file to RAPHIMG.nbh. Format your sd card (1-2 gb works best) to FAT32, and put the image on the root of the card. Go into bootloader (well, you're already there, you may not need to) by holding volume down and soft resetting. Hold vol. down until the tri-color screen appears. At the prompt, press the power button, and let the flash run its course. Soft reset when it says that the update was a success. Let the phone boot up until it gets to the the alignment screen, the hard reset and boot it up.
If you don't have an .nbh file, and instead have a .exe file from vodaphone/htc, then you should be able to extract the contents with either winrar or 7-zip (google) to get at the .nbh image file. I've done this before, and it works fine.
Many thanks to all who have replied. I have fixed the problem. It turns out that it was the download to my PC that was at fault. I downloaded the Vodafone software to my lap top and ran it from there and it has recovered the phone. I now have a spare, and working, Touch Pro. I may try the HardSPL and other ROMS just to use the phone as a test bed. Alternatively, anyone out there want to make me an offer?
Hollybeau
Hollybeau said:
Alternatively, anyone out there want to make me an offer?
Click to expand...
Click to collapse
Ask in market place and you will probably get some takers