hello everyone,
i seem to have a problem with the camera of my blue angel,whenever i try to turn it on it gets this error "unable to start preview mode,internal error 36001:101:1 "
i already tried soft reset but is seems not to work :? , i was thnking of doing a hard reset but would there be any other way to solve this before i do a hard reset?
thanks!
shareo
Hi...
try to unlock and unhide ext ROM,by installing extrom unlocker for BA found in the ftp or at buzzdev,then click on the IA camera cab,this will reinstall ur camera software...if this works,then no need to hard reset anymore.. :wink:
Good luck...
RAGO :lol:
re:"Unable to start preview mode" camera erro
ok,thanks! i'll try that!hope that it works.
Related
I own an MDA compact on t-mobile uk,
whilst on there homepage i saw a "update your MDA software"alert,
i downloaded the software and ran it.
the MDA then went off and when turned back ran a hard reset.
the MDA then runs thru the set up,when thats complete is shows a grey type screen with serail v1.02
its frozen on this screen and unuseable any effort to do anything makes a repeat cycle of the above
please help me turn my paperweight back into a pda
thank you very much
(i think im best sticking to a standard phone from here on in,im not techy enuff to have a pda.doh!)
ur just in bootloader..go read wiki
u gotta press the reset,power and record camera btton together..thats wot i do for my 9090
thank you very much for your help
its appreciated .
ill try that
thanks again friend.
Jace,
the power & camera & soft-reset button will bring you in bootloader, just where you're now.
You'd better connect USB & run the update again. Something got broke the previous time, that's why you're in bootloader now.
Regards, M
brill guys ta
only problem(sorry guys still learning)from the bootload screen the pc wont see the device is connected and if i try to run the device to get to a standard screen to sync it just reboots?
how do i actisync while in bootloader?
ta
Jace pls don't try Act.sync. Run the update again :!:
ive manged to get the pc to see the pda and ran it under a guest partnership,
once it had seent he pda, i re-ran the update,but each time it goes thru the motions then gives and error msg.
man im goin back to a normal handset next time
What rom nr are you flashing? & what's the error message?
Cheers, M
Thanks for all your help sorry to be such a pain.
i got the file from the tmobile uk site .
file name ma-tmuk-11300-128-11200
when connectiong its says
updating from
device ce image:1.13.00
device ext imagethis is blank)
deivce radio:1.12.00
up dating to
device ce image:1.13.00
device ext image:1.13.128
deivce radio:1.12.00
it runs thru then stops and says
error 101:connection error
thanks
when booting up the bottom right shows
R 1.12.00
G t1337.42
D 1.13.00wwe
Ok that's the 1.13WWE rom, which is available sine october last year. Should be a normal rom without problems. If you never updated before & still in your warranty period, return your device.
BTW have you rebooted your PC during your sequence off tries?
Guess your no pain, but you got bad luck in upgrading this time. You did the right steps to cure everything.
Cheers, M
great thanks,
i have rebooted pc but ill do that then retry nothign to loose at this stage thanks mate
Did you ever make a rom-dump of your working device? Otherwise you can try to make one now & do a SD-update.
Cheers, M
no i didnt mate doh
ta for all your help mate appricated
when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up
try this
1) hold your communication button and soft reset *keep holding comm-button until see the RGB color bar,
2) plug-in your USB cable, u will see a 'USB' appear at your bottom left,
3) install the flash ROM from your window.
well I tried install WM6 once fail, so I do the above step, and 2nd time successfully upgrade to WM6, you can use back your original ROM download form dopod site.
goodluck
feiyee said:
when i flashing my dopod , my house suddenly blackout.
So what happened to my dopod is that i stuck at IPL, SPL , GMS , OS page, and it didnt load windows anymore.
I tried to hard reset it , but it helpless
I can go in bootloader.
Is their any possible way to install a fresh rom into it?
Searched around , but found nothing. Pls help up
Click to expand...
Click to collapse
It's easy, mail your dopd to me.
Hi all,
I have tried to install WM6 but got the really big problem. The installation success but my Dopod 818 pro can't start and hang on the black screen. Try to hard reset but show:
formatting to FAT,
format failed
Any expert can help me... or show me how to downgrade it back to normal...
i'm really new on this..
(
thanks,
Ezuan
Did you unplugged your prophet after getting the "FINNISH" message from windows screen? Once i didn't do it,then it happened to me what you explain. Reflash again and this time unplug it before doing hard reset. If you are not able to get it going, try reflashing a wm5 rom from anyware around, then flash wm6 (you have to downgrade)
Search for instance lsvw 2.3 or jesterz rom in this forum
regards
ezuanizam, I've had the same problem and I replied to you in another topic: http://forum.xda-developers.com/showthread.php?t=302110
i have tired v3 wm6 update and..after the update my screen is stuck...at o2 sign..with bubbles,, the four red words appear on the screen but doesn't change anything...
i'd like to reflash back but it doesn't seem like connecting to PC via USB..
what do i do...?
and i found..
it just stopps in the boot loader mode and turns to black screeen .. and that's it...
I cna't even connect to USB so which means i can't flash back to normal..
is there any suggestions??
like resseting back up?
I have tried soft and hard reset but both don't seem to work.. still stuck in the bootloader mode....
What do I DO>>>>>>>>>>>>>....please help me...><
Try to Enter Bootloader:
Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
However, you have to write in the right post, i guess you mean the Ohlala_WWE_WM6_v3 ROM. If you had read the entire post youl'd know that this one is bad. V4 should solve the problem.
thanks for your answer !!but..
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
llvll said:
yes i have entered to that 3 coloured mode(bootloader mode like you said)
and I have connected my usb and it showed USB on the left corner ...
but the problem is...after I connect usb.. computer doesn't recognize my O2 device so I can't reflash my rom with SMart 1.
I ran the file called "upgrade_rom" for smart1 wm6 but it keeps telling me that "no device found.." so..
what should i do...
please help me...
and i really thank you for your response!
Click to expand...
Click to collapse
You cannot use "upgrade_rom.bat" to flash ur device with RGB screen. The bat file is for upgrade, not for fresh install. It means that you have to install AKU2.xx NVID.exe (executable) first. The .exe file can recognize ur device via RGB screen.
After reset ur device with AKU2.x and successfully connect to the PC vis Activesync, you then can run upgrade_rom.bat.
And... don't be too panic. You have to read more.
thank you so much !!
i' ll try it right now !! omg ...i'm so relived that I got an answer !!!
you are the best!
um...
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
llvll said:
i search it thru the forum.. but i Can't seem to find that file... AKU2 .xx.nvid..
can you please direct me to download that program?..
please... thanks again !
Click to expand...
Click to collapse
here http://www.4shared.com/file/12240109/ca99469a/RUU_Prophet_220734_2207114_024721_NVID.html
thanks !!!
is there an o2 version of NVID??? anywhere? i've just installed this but it says Qteck..
No it's a Qteck ROM not an O², I don't know if there is a 2.20 NVID ROM from O² here, sorry.
i've just installed AKU...thing
after installing AKU...
my phone doesn't seem like it can connect to Antisync program..
is there any reason why..this is happpenin..?
make hard reset after flash firmware!
yese !!
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
you could try this. Someone else posted it here, and when my phone stopped connecting after some update it fixed activesync. It's a switch.
llvll said:
i did the hard reset but still Activesync says It cannot be connected...
is there any other way to fix this???
I don't no if this can help but.. my device orignally was O2 and now i flashed up with Qteck AKU...
does this matter...?
if then would you let me know where i can find o2 AKU file..please...?
thanks for your reply !
Click to expand...
Click to collapse
Had O2 ever released HTC Prophet?
Sorry but I'm not O2 fan.
I have only Prophet so I know only Prophet.
You could go to the right thread for ur device O2 and look for the right .exe file.
PS: is it XDA Neo? If it is Prophet it should be OK.
Try holding Camera+Comm buttons during pressing reset button ur device will ask u to Format something. Press send button (green phone button) and try again.
Safe
Thanks guys, you saved my S200
Matos
Ohyea !!
I found the solution !!! dat Qteck one worked but um....
yea and my phone is Xda Neo !!!
the black one !
thanks for all the replies guys !!!!!!!
Whoohoo, thanx for mentioning the bootloader mode (by only holding the camera button ) Now I can try another WM6 rom, which does work I hope
hello there same problem here.. mine is also xda neo.. when trying to upgrade wm6 it stuck exactly same as yours..how did u fix the problem? thanx for ur advice
First sorry for my english
I have big problem since i've instaled few programs on my flashed polaris.
Rom i've instaled is Touch-IT Lite made by itje, and programs i've instaled are:
s2u2
s2p
s2v
trottleluncher
tcpmp
All of them works very good, but when i pug my earphones s2u2 start s2p and didnt start music... and stop everything...
now when i try to HR or turn on my polaris stop at red numbers and not want to go.
Do i have to go to serwis ?
Whot should i do to polaris work ??
thx for ansfers
can't enter bootloader
I've big problem not becouse of that i can't connect with activesynth
the point off problem is that i can't enter bootloader mode, and repair my phone by flashing it with sd card :/
1Q : When i have to press camera button and reset ?
2Q : How much time i have to hold these buttons ?
THX for help
CRC
Anybody help ??
One more question:
If i have custom rom crc will repair my phone ?